PRODUCT DATA SHEET P3920 HDSL Transformer Features Applications ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Conexant HDSL ∗ SDSL Leasd-free (Pb-free) Low Distortion IEC 950 and UL 60950 Certified UL Recognized Component Supplementary Insulation Surface Mount Industry Standard Footprint DESCRIPTION P3920 is a low distortion transformer intended for Conexant HDSL chipsets e.g. BT8921 and BT8970. P3920 is certified to safety standards IEC 950 and UL 60950 for supplementary insulation, 250V working voltage. P3920 is a UL Recognized Component and is supported by an IEC CB Test Certificate. The part is completely lead-free and suitable for lead-free and conventional processing. ETALDOC 752/7 Page 1 of 4 The safety system yields very low transformer parasitics, ensuring that P3920 exhibits excellent frequency response and balance; in combination with its good harmonic distortion performance, P3920 is ideally suited to low cost yet demanding HDSL applications. January 2004 P3920 SPECIFICATIONS Electrical Typical values at T = 25ºC, unless otherwise stated. Parameter Conditions Min Typ Max Units Inductance 10kHz 100mV 1-5 (link 2-4) 1.8 2.0 2.2 mH Leakage inductance 100kHz, 100mV, 1-5 (link 2-4; link 7-9) - - 12 µH DC resistance 1-4; 2-5; 7-9 - - 0.8 Ω 1.98 2.00 2.02 - Turns ratio 1-5 : 9-7 ( link 2-4) Frequency response (1) 30kHz – 300kHz - - ±0.2 dB Longitudinal balance (1) 20kHz – 300kHz 50 - - dB - - -80 dB 2.12 3.0 - - kVrms kV -40 -40 - +85 +85 ºC ºC Total Harmonic (1) Distortion Voltage isolation Operating range: Functional Storage 20kHz 2Vrms 1-5 (link 2-4) (2) 50Hz DC (1, 2, 4, 5 : 7, 9) Ambient temperature Notes 1. 135Ω line, 32Ω equipment. 2. Components are 100% tested at 3.25kV DC. ETALDOC 752/7 Page 2 of 4 January 2004 P3920 Dimensions Connections Fig. 1 Fig. 2 15.40 17.15 max (0.67) 2,50 (0.098) CONSTRUCTION (0.606) 0.80 (0.032) 0.70 (0.028) 2,5 (0.10) 0.7 (0.03) 12.9 max (0.51) 13.0 (0.51) 12.2 max (0.48) CHAMFER ON BOBBIN Terminals finished: SnAg Dimensions shown are in millimetres (inches). SAFETY ABSOLUTE MAXIMUM RATINGS Constructed in accordance with IEC 60950-1, EN 60950-1 and UL 60950-1, supplementary insulation, 250V maximum working voltage, flammability class V-0. (Ratings of components independent of circuit). Short term isolation voltage (1s) 2.12kVrms, 3.0kVDC Installation requirements should be observed whereby a minimum of 1.0mm creepage and 1.5mm clearance is maintained between the ferrite core and accessible conductive parts in the host equipment. Storage temperature -40ºC to +85ºC Reflow temperature (10s) 260ºC ETALDOC 752/7 Page 3 of 4 January 2004 P3920 CERTIFICATION COPYRIGHT Certified by BSI to IEC 950:1991/A4:1996 (IEC CB Test Certificate No. GB518W) sub-clauses 1.5, 1.5.1, 1.5.3, 2.2, 2.2.2, 2.2.3, 2.2.4, 2.9.2, 2.9.3, 2.9.4, 4.4, 4.4.3.2 (class V-0) and 5.3 for a maximum working voltage of 250Vrms, nominal mains supply voltage not exceeding 300Vrms and a maximum operating temperature of +85ºC in Pollution Degree 2 environments, supplementary insulation, clearance greater than 2.0mm, creepage greater than 2.5mm, distance through solid insulation greater than 0.4mm. Certification covers Appendix ZB deviations for Sweden and Norway. ETAL and P3920 are Trade Marks of Profec Technologies Ltd. The Trade Mark ETAL is registered at the UK Trade Marks Registry. Profec Technologies Ltd. is the owner of the design right under the Copyright Designs and Patents Act 1988 and no rights or licences are hereby granted or implied to any third party. © 2000 – 2004 Profec Technologies Ltd. Reproduction prohibited. national Recognized under the Component Recognition Program of Underwriters Laboratories Inc. to US and Canadian requirements CAN/CSA C22.2 No. 60950-1-03/UL60950-1, First Edition, based on IEC 60950-1, First Edition, maximum working voltage 250Vrms, Pollution Degree 2, supplementary insulation. UL File number E203175. Additionally, Profec Technologies certifies all transformers as providing voltage isolation of 2.12kVrms, 3kV DC minimum. All shipments are supported by a Certificate of Conformity to current applicable safety standards. E203175 ISO 9001 FM 25326 ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Website: www.etalgroup.com Email: [email protected] ETALDOC 752/7 Page 4 of 4 January 2004