IRLZ44, SiHLZ44 Vishay Siliconix Power MOSFET FEATURES PRODUCT SUMMARY VDS (V) • Dynamic dV/dt Rating 60 V RDS(on) (Ω) VGS = 5.0 V Available • Logic-Level Gate Drive 0.028 Qg (Max.) (nC) 66 • RDS(on) Specified at VGS = 4 V and 5 V Qgs (nC) 12 • 175 °C Operating Temperature Qgd (nC) 43 • Fast Switching Configuration RoHS* COMPLIANT • Ease of Paralleling Single • Simple Drive Requirements D TO-220 • Lead (Pb)-free Available DESCRIPTION Third generation Power MOSFETs from Vishay provide the designer with the best combination of fast switching, ruggedized device design, low on-resistance and cost-effectiveness. The TO-220 package is universally preferred for all commercial-industrial applications at power dissipation levels to approximately 50 W. The low thermal resistance and low package cost of the TO-220 contribute to its wide acceptance throughout the industry. G S G D S N-Channel MOSFET ORDERING INFORMATION Package TO-220 IRLZ44PbF SiHLZ44-E3 IRLZ44 SiHLZ44 Lead (Pb)-free SnPb ABSOLUTE MAXIMUM RATINGS TC = 25 °C, unless otherwise noted PARAMETER Gate-Source Voltage Continuous Drain Currente Continuous Drain Current Pulsed Drain VGS at 5.0 V TC = 25 °C TC = 100 °C Currenta SYMBOL LIMIT UNIT VGS ± 10 V ID Maximum Power Dissipation Peak Diode Recovery TC = 25 °C dV/dtc Operating Junction and Storage Temperature Range Soldering Recommendations (Peak Temperature)d Mounting Torque for 10 s 6-32 or M3 screw 36 A IDM 200 1.0 W/°C EAS 400 mJ PD 150 W dV/dt 4.5 V/ns TJ, Tstg - 55 to + 175 Linear Derating Factor Single Pulse Avalanche Energyb 50 300 °C 10 lbf · in 1.1 N·m Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. VDD = 25 V, starting TJ = 25 °C, L = 179 µH, RG = 25 Ω IAS = 51 A (see fig. 12). c. ISD ≤ 51 A, dV/dt ≤ 250 A/s, VDD ≤ VDS, TJ ≤ 175 °C. d. 1.6 mm from case. e. Current limited by the package, (die current = 51 A). * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 91328 S-81274-Rev. A, 16-Jun-08 www.vishay.com 1 IRLZ44, SiHLZ44 Vishay Siliconix THERMAL RESISTANCE RATINGS PARAMETER SYMBOL TYP. MAX. Maximum Junction-to-Ambient RthJA - 62 Case-to-Sink, Flat, Greased Surface RthCS 0.50 - Maximum Junction-to-Case (Drain) RthJC - 1.0 UNIT °C/W SPECIFICATIONS TJ = 25 °C, unless otherwise noted PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Static Drain-Source Breakdown Voltage VDS Temperature Coefficient VDS VGS = 0 V, ID = 250 µA 60 - - V ΔVDS/TJ Reference to 25 °C, ID = 1 mA - 0.070 - V/°C VGS(th) VDS = VGS, ID = 250 µA 1.0 - 2.0 V Gate-Source Leakage IGSS VGS = 10 V - - ± 100 nA Zero Gate Voltage Drain Current IDSS VDS = 60 V, VGS = 0 V - - 25 VDS = 48 V, VGS = 0 V, TJ = 150 °C - - 250 Gate-Source Threshold Voltage Drain-Source On-State Resistance Forward Transconductance RDS(on) gfs VGS = 5.0 V ID = 31 Ab - - 0.028 VGS = 4.0 V ID = 25 Ab - - 0.039 23 - - - 3300 - - 1200 - - 200 - - - 66 - - 12 VDS = 25 V, ID = 31 Ab µA Ω S Dynamic Input Capacitance Ciss Output Capacitance Coss Reverse Transfer Capacitance Crss Total Gate Charge Qg Gate-Source Charge Qgs VGS = 0 V, VDS = 25 V, f = 1.0 MHz, see fig. 5 VGS = 5.0 V ID = 51 A, VDS = 48 V, see fig. 6 and 13b Gate-Drain Charge Qgd - - 43 Turn-On Delay Time td(on) - 17 - Rise Time Turn-Off Delay Time Fall Time tr td(off) VDD = 30 V, ID = 51 A, RG = 4.6 Ω, RD = 0.56 Ω, see fig. 10b tf Internal Drain Inductance LD Internal Source Inductance LS Between lead, 6 mm (0.25") from package and center of die contact D - 230 - - 42 - - 110 - - 4.5 - - 7.5 - - - 50c - - 200 pF nC ns nH G S Drain-Source Body Diode Characteristics Continuous Source-Drain Diode Current IS Pulsed Diode Forward Currenta ISM Body Diode Voltage VSD Body Diode Reverse Recovery Time trr Body Diode Reverse Recovery Charge Qrr Forward Turn-On Time ton MOSFET symbol showing the integral reverse p - n junction diode D A G S TJ = 25 °C, IS = 51 A, VGS = 0 Vb TJ = 25 °C, IF = 51 A, dI/dt = 100 A/µsb - - 2.5 V - 130 180 ns - 0.84 1.3 µC Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD) Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. Pulse width ≤ 300 µs; duty cycle ≤ 2 %. c. Current limited by the package, (die current = 51 A). www.vishay.com 2 Document Number: 91328 S-81274-Rev. A, 16-Jun-08 IRLZ44, SiHLZ44 Vishay Siliconix TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted Fig. 1 - Typical Output Characteristics, TC = 25 °C Fig. 2 - Typical Output Characteristics, TC = 175 °C Document Number: 91328 S-81274-Rev. A, 16-Jun-08 Fig. 3 - Typical Transfer Characteristics Fig. 4 - Normalized On-Resistance vs. Temperature www.vishay.com 3 IRLZ44, SiHLZ44 Vishay Siliconix Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage www.vishay.com 4 Fig. 7 - Typical Source-Drain Diode Forward Voltage Fig. 8 - Maximum Safe Operating Area Document Number: 91328 S-81274-Rev. A, 16-Jun-08 IRLZ44, SiHLZ44 Vishay Siliconix RD VDS VGS D.U.T. RG + - VDD 5.0 V Pulse width ≤ 1 µs Duty factor ≤ 0.1 % Fig. 10a - Switching Time Test Circuit VDS 90 % 10 % VGS td(on) Fig. 9 - Maximum Drain Current vs. Case Temperature td(off) tf tr Fig. 10b - Switching Time Waveforms Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case VDS L Vary tp to obtain required IAS VDS tp VDD D.U.T RG + - IAS V DD VDS 5.0 V tp 0.01 Ω Fig. 12a - Unclamped Inductive Test Circuit Document Number: 91328 S-81274-Rev. A, 16-Jun-08 IAS Fig. 12b - Unclamped Inductive Waveforms www.vishay.com 5 IRLZ44, SiHLZ44 Vishay Siliconix Fig. 12c - Maximum Avalanche Energy vs. Drain Current Current regulator Same type as D.U.T. 50 kΩ QG 5.0 V 12 V 0.2 µF 0.3 µF QGS + QGD D.U.T. VG - VDS VGS 3 mA Charge Fig. 13a - Basic Gate Charge Waveform www.vishay.com 6 IG ID Current sampling resistors Fig. 13b - Gate Charge Test Circuit Document Number: 91328 S-81274-Rev. A, 16-Jun-08 IRLZ44, SiHLZ44 Vishay Siliconix Peak Diode Recovery dV/dt Test Circuit + D.U.T. Circuit layout considerations • Low stray inductance • Ground plane • Low leakage inductance current transformer + - - RG • • • • dV/dt controlled by RG Driver same type as D.U.T. ISD controlled by duty factor "D" D.U.T. - device under test Driver gate drive P.W. + Period D= + - VDD P.W. Period VGS = 10 V* D.U.T. ISD waveform Reverse recovery current Body diode forward current dI/dt D.U.T. VDS waveform Diode recovery dV/dt Re-applied voltage VDD Body diode forward drop Inductor current Ripple ≤ 5 % ISD * VGS = 5 V for logic level devices Fig. 14 - For N-Channel Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see http://www.vishay.com/ppg?91328. Document Number: 91328 S-81274-Rev. A, 16-Jun-08 www.vishay.com 7 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1