RFMA5065-2W 5.0 – 6.5 GHz Power Amplifier MMIC UPDATED 09/01/2006 FEATURES • • • • 5.0 – 6.5 GHz Operating Frequency Range 33dBm Output Power at 1dB Compression 30.0 dB Typical Power Gain @1dB gain compression -44dBc Typical OIM3 @ each tone Pout 22dBm N/C RF IN Vd Excelics RFMA5065 -2W-02 N/C N/C RF OUT N/C Vg APPLICATIONS • • Point-to-point and point-to-multipoint radio Military Radar Systems Caution! ESD sensitive device. ELECTRICAL CHARACTERISTICS (Tb = 25 °C, 50 ohm, Vdd=10V, Vgg=-5V) SYMBOL PARAMETER/TEST CONDITIONS MIN TYP MAX UNITS 6.5 GHz Operating Frequency Range 5.0 P1dB Output Power at 1dB Gain Compression 32 33 dBm G1dB Gain @1dB gain compression Output 3rd Order Intermodulation Distortion @∆f=10MHz, Each Tone Pout 22dBm 28.0 32.0 dB -40 -44 dBc F OIMD3 Input RL Output RL Input Return Loss -12 Output Return Loss -6 Idd Drain Current @small signal output power level Vdd Drain Supply Voltage 10 Vgg Gate Supply Voltage -5 Rth Thermal Resistance Tb Operating Base Plate Temperature MAXIMUM RATINGS SYMBOL 1260 -6 dB 1500 V 4.5 + 80 o C/W ºC @25°C1,2 CHARACTERISTIC ABSOLUTE CONTINUOUS Vdd Drain Supply Voltage 14V 10V Vgg Gate Supply Voltage -10V -5.5 V Idq Quiescent Drain Current Idss 1.5A Igg Gate Current 150mA 50 mA PIN Input Power 8dBm @ 3dB compression TCH Channel Temperature 175°C 150°C TSTG Storage Temperature -65/175°C -65/150°C 30W 15W Pt mA V 4 - 30 dB Total Power Dissipation 1. Operating the device beyond any of the above rating may reduce MTTF and cause permanent damage. 2. Bias conditions must also satisfy the following equation Vdd*Idd < (TCH –Tb)/RTH Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 page 1 of 2 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Revised September 2006 RFMA5065-2W 5.0 – 6.5 GHz Power Amplifier MMIC UPDATED 09/01/2006 Package Dimension and Pin Assignment 0.433 4X.050 CHAMFER 0.216 2X DIA .090 THRU 0.204 PIN1 Indicator N/C 6x0.100 RF IN 0.709 Excelics RFMA5065 -2W-02 N/C Vd N/C 0.591 RF OUT 8 X .013 N/C Vg 8X 0.100±0.010 0.075 8X 0.004 0.040 0.025 DIMENSION: INCH TOLERANCE: ±0.005 Ordering Information Part Number RFMA5065-2W-02 Refer 02 Package Outline Application Note 1. The package should be screwed onto a good heat sink and ground 2. Turn on/off sequence is required: ---to turn on: apply -5V first, then +10V. ---to turn off: turn +10V off first, then turn -5V off 3. Recommended Bias Circuit and Internal Block Diagram “N/C” pins on package can be either grounded or left open. (No connection inside of package) Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 page 2 of 2 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Revised September 2006