Finisar Product Specification OC-48 IR-1/STM S-16.1 Multirate 2x10 SFF Transceiver FTLF1421S1xCL PRODUCT FEATURES • Up to 2.67Gb/s bi-directional data links • Standard 2x10 pin SFF footprint (MSA compliant) • Analog diagnostics functions • Uncooled 1310nm DFB laser transmitter • Duplex LC connector • Very low jitter • Metal enclosure, for lower EMI • SONET OC-48 IR-1 / SDH STM S-16.1 • Single 3.3V power supply • SONET OC-12 IR-1 / SDH STM S-4.1 • Low power dissipation <700 mW typical • SONET OC-3 IR-1/ SDH STM S-1.1 • • Gigabit Ethernet / 1x/2x Fibre Channel Extended operating temperature range: -10°C to 70°C APPLICATIONS Finisar’s FTLF1421S1xCL Small Form Factor (SFF) transceivers are compatible with the Small Form Factor Multi-Sourcing Agreement (MSA)1. They comply with SONET OC48 IR-1 (SDH STM S-16.1) standards2, and are compatible with Gigabit Ethernet as specified in IEEE Std 802.33, Fibre Channel FC-PI 13.04, SONET OC-12 and SONET OC-3 standards2. The transceivers are RoHS compliant and lead-free per Directive 2002/95/EC5 and Finisar Application Note AN-20386. PRODUCT SELECTION FTLF1421S1xCL x G M K H 2 Grounding Pins, Short EMI shield 6 Grounding Pins, Short EMI shield 2 Grounding Pins, Long EMI shield 6 Grounding Pins, Long EMI shield Finisar Corporation March, 2006 Rev A Page 1 FTLF1421S1XCL 2x10 Pin SFF Product Specification – December 2003 I. Finisar Pin Descriptions Pin MS Symbol MS Name/Description Mounting Studs for mechanical attachment. Chassis ground is internally isolated from circuit ground. Connection to chassis ground is recommended. 1 PD 2,3,6 4,5 7 8 9 10 11 12,16 13 14 VEER NC VCCR SD RDRD+ VCCT VEET TDIS TD+ Receiver Power Monitor. This pin must be connected to a positive voltage supply (Vcc), preferably via a small resistor. Supplies photocurrent and may be used to monitor received power. Receiver Ground (Common with Transmitter Ground) Not Connected. Receiver Power Supply Signal Detect. Logic 1 indicates normal operation. Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Disable Transmitter Non-Inverted DATA in. AC Coupled. 15 TD- Transmitter Inverted DATA in. AC Coupled. 17 Bmon- Laser Bias Monitoring (-). 18 Bmon+ 19 Pmon- 20 Pmon+ Laser Bias Monitoring (+) .(Bmon+ - Bmon-) = 10Ω x laser bias current. Laser Power Monitoring (-). Current implementation connects this pin to ground Laser Power Monitoring (+) .(Pmon+ - Pmon-) = 200Ω x mon. photodiode current. Logic Family NA Analog Current NA NA LVTTL CML CML NA NA LVTTL CML ECL CML ECL Analog Voltage Analog Voltage Analog Voltage Analog Voltage MS 20 19 18 17 16 15 14 13 12 11 TOP VIEW 1 2 3 4 5 6 7 8 9 10 MS Finisar Corporation March, 2006 Rev A Page 2 Finisar FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Lead Soldering Temperature/Time III. Symbol Vcc TS TOP RH Min -0.5 -40 -10 0 Typ Max 4.5 85 70 85 260/10 Unit V °C °C % °C/s Ref. 1 Electrical Characteristics (TOP = -10 to 70 °C, VCC = 3.00 to 3.60 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data output rise time Data output fall time SD Assert SD De-Assert Power Supply Rejection Total Generated Receiver Jitter (peak to peak) Total Generated Receiver Jitter (rms) Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr tf VSD assert VSD deassert PSR JRXp-p JRXrms Min 3.00 Typ 200 Max 3.60 300 Unit V mA Ref. Ω mV V V us 2 1200 Vcc Vee+ 0.8 10 100 250 Vcc – 1.3 Vee 300 Vcc – 0.5 Vee 100 400 100 100 800 175 175 Vcc Vee+0.5 0.07 mV ps ps V V mVpp UI 0.007 UI 3 4 5 5 6 6 7 Notes: 1. Non condensing. 2. AC coupled. 3. Or open circuit. 4. Into 100 ohm differential termination. 5. 20 – 80 % 6. Signal Detect is LVTTL. Logic 1 indicates normal operation; logic 0 indicates no signal detected. 7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000. Finisar Corporation March, 2006 Rev A Page 3 Finisar FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 IV. Optical Characteristics (TOP = -10 to 70 °C, VCC = 3.00 to 3.60 Volts) Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width –20dB Optical Extinction Ratio Sidemode Supression ratio Optical Rise/Fall Time Relative Intensity Noise Total Generated Transmitter Jitter (peak to peak) Total Generated Transmitter Jitter (rms) Receiver Average Rx Sensitivity @ 2.67Gb/s Average Rx Sensitivity @ OC-48 Average Rx Sensitivity @ 2X Fibre Channel Average Rx Sensitivity @ Gigabit Ethernet Average Rx Sensitivity @ OC-12 Average Rx Sensitivity @ OC-3 Optical Center (Input) Wavelength Receiver Reflectance SD Assert SD De-Assert SD Hysteresis Symbol Min POUT λ σ ER SSRmin tr/ tf RIN JTXp-p -5 1270 Typ Max Unit 0 1360 1 180 -120 0.07 dBm nm nm dB dB ps dB/Hz UI 0.007 UI 8.2 30 JTXrms Ref. 1 2 RSENS1 RSENS1 RSENS2 0 0 0 -18 -18 -21 dBm dBm dBm 3 3 4 RSENS3 0 -22 dBm 4 RSENS4 RSENS5 λC RRx SDA SDD 0 -10 1270 -22 -23 1600 -27 -19 dBm dBm nm dB dBm dBm dB 5 5 -30 0.5 Notes: 1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. Unfiltered , 20 – 80% 3. With worst-case extinction ratio. Measured with a PRBS 231-1 test pattern interspersed with 72 consecutive ones and 72 consecutive zeros. 4. With worst-case extinction ratio. Measured with a PRBS 27-1 test pattern. 5. With worst-case extinction ratio. Measured with a PRBS 223-1 test pattern. Finisar Corporation March, 2006 Rev A Page 4 Finisar FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 V. General Specifications Parameter Data Rate Bit Error Rate @ OC-48 Max. Supported Link Length on 9/125µm SMF @ OC-48 Max. Supported Link Length on 9/125µm SMF @ 2X Fibre Channel Max. Supported Link Length on 9/125µm SMF @ Gigabit Ethernet Max. Supported Link Length on 9/125µm SMF @ OC-12 Max. Supported Link Length on 9/125µm SMF @ OC-3 Symbol BR BER LMAX1 Min 155 Typ Max 2667 10-12 20 Units Ref. Mb/sec 1 2 km 3 LMAX2 30 km 3 LMAX3 30 km 3 LMAX4 30 km 3 LMAX5 30 km 3 Notes: 1. SONET OC-48 IR-1/SDH STM S-16.1 compliant. Compatible with Gigabit Ethernet, 1x/2x Fibre Channel, SONET OC-12 and OC-3. Supports FEC at 2.67Gb/s. 2. Tested with a PRBS 231-1 test pattern interspersed with 72 consecutive ones and 72 consecutive zeros. 3. Attenuation of 0.55 dB/km is used for the link length calculations (per GR-253 CORE). Distances are indicative only. A 2dB penalty is included for dispersion on >2db data rates. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application. VI. Environmental Specifications Finisar 1310nm SFP transceivers have an extended operating temperature range from –10°C to +70°C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -10 -40 Typ Max 70 85 Units °C °C Ref. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. Finisar Corporation March, 2006 Rev A Page 5 Finisar FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 VIII. Analog Diagnostics Functions (Top = -10 to 70 °C, VCC = 3.00 to 3.60 Volts) Parameter Transmitter Monitor photodiode current monitor Laser bias current monitor Symbol Min Pmon+, PmonBmon+, BmonRpd R Vpd 0 0.5 2.4 Receiver Received photocurrent Photodiode responsivity Applied voltage at PD pin Typ Max Unit 0 Vcc V 1 0 Vcc V 2 1 1.0 Vcc mA A/W V 3 0.9 Ref. 3 Notes: 1. Pins 19 and 20 provide an analog voltage output proportional to the monitor photodiode current, per the following formula: IBIAS = .V(Pmon+ - Pmon-) / 200Ω. The figure below shows the equivalent circuit. 2. Pins 17 and 18 provide an analog voltage output proportional to the laser bias current, per the following formula: IBIAS = .V(Bmon+ - Bmon-) / 10Ω. The figure below shows the equivalent circuit. 3. Pin 1 is used to monitor the received photocurrent. It must be connected to a positive voltage within the range specified above. The current that flows into this pin is the received photocurrent. The received power is given by the photocurrent multiplied by the photodiode responsivity. Vpd Vcc Vcc Laser Monitor Photodidoe 3 KΩ 3 KΩ Ipd Pmon+ Bmon+ 10 Ω 200 Ω Pmon- Bmon3 KΩ 3 KΩ Ibias Imon Receiver Photodidoe Analog monitoring function connections. Finisar Corporation March, 2006 Rev A Page 6 FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 IX. Finisar Mechanical Specifications Finisar’s OC-48/STM-16 Small Form Factor (SFF) transceivers comply with the standard dimensions defined by the Small Form Factor Multi-Sourcing Agreement (MSA). FTLF1421S1GCL (dimensions are in inches) – 2 pin version Finisar Corporation March, 2006 Rev A Page 7 FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 Finisar FTLF1421S1HCL (dimensions are in inches) – 6 pin version Finisar Corporation March, 2006 Rev A Page 8 FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 Finisar FTLF1421S1HCL – 6 pin version (Long EMI Shield) Finisar Corporation March, 2006 Rev A Page 9 FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 X. Finisar PCB Layout and Bezel Recommendations Minimum Recommended Pitch is 0.600” Finisar Corporation March, 2006 Rev A Page 10 FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 Finisar XI. References 1. Small Form Factor (SFF) Transceiver Multi-Source Agreement (MSA). January 1998. Documentation is available from Finisar upon request. 2. Bellcore GR-253 and ITU-T G.957 Specifications (Transmitter Optical Output Power complies with SONET OC-48 requirements only). 3. IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-LX. IEEE Standards Department, 2002. (Transmit Optical Output has a minimum Extinction Ratio of 8.2 dB only). 4. “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0)”. American National Standard for Information Systems. (*) 5. Directive 2002/95/EC of the European Council Parliament and of the Council. “On the restriction of the use of certain hazardous substances in electrical and electronic equipment”. January 27, 2003. 6. “Application Note AN-2038: Finisar Implementation of RoHS Compliant Transceivers:. Finisar Corporation, January 21, 2005. (*) Neither IEEE 802.3 nor FC-PI 13.0 specifies a 1310nm DFB single mode interface. The FTLF1421S1XCL complies with these standards except for receiver sensitivity, and transmit output power. See Section IV for details. XII. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com Finisar Corporation March, 2006 Rev A Page 11 FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 Finisar Corporation March, 2006 Rev A Finisar Page 12