FINISAR FTLF1721P2BCL

Product Specification
OC-48 LR-1/STM L-16.1 RoHS Compliant Pluggable SFP Transceiver
FTLF1721P2xCL
PRODUCT FEATURES
•
Up to 2.67Gb/s bi-directional
data links
•
Hot-pluggable SFP footprint
•
Built-in digital diagnostic functions
•
Uncooled 1310nm DFB laser
transmitter
•
APD Receiver
•
Duplex LC connector
•
RoHS Compliant
•
Metal enclosure, for lower EMI
•
Single 3.3V power supply
•
Low power dissipation <700mW
typical
•
APPLICATIONS
•
SONET OC-48 LR-1 / SDH STM L-16.1
•
SONET OC-12 / SDH STM 4
•
SONET OC-3 / SDH STM-1
•
Gigabit Ethernet / 1x/2x Fibre Channel
Commercial operating temperature
range: -10°C to 70°C
Finisar’s FTLF1721P2xCL Small Form Factor Pluggable (SFP) transceivers are
compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1.
They comply with SONET OC-48 LR-1 (SDH STM L-16.1) standards2, Gigabit Ethernet
as specified in IEEE Std 802.33(*) and Fibre Channel FC-PI-2 Rev. 7.04(*). They are
compatible with SONET OC-12 SR and SONET OC-3 standards2 and are RoHS
compliant per Directive 2002/95/EC5 and Finisar Application Note AN-2038. Digital
diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA.
PRODUCT SELECTION
FTLF1721P2xCL
x
W
B
© Finisar Corporation January 20, 2006 Rev. A
Wide Extraction Bail
Narrow Extraction Bail
Page 1
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
I.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Pin Descriptions
Symbol
VEET
TFAULT
TDIS
MOD_DEF(2)
MOD_DEF(1)
MOD_DEF(0)
Rate Select
LOS
VEER
VEER
VEER
RDRD+
VEER
VCCR
VCCT
VEET
TD+
TDVEET
Name/Description
Transmitter Ground (Common with Receiver Ground)
Transmitter Fault. Not supported.
Transmitter Disable. Laser output disabled on high or open.
Module Definition 2. Data line for Serial ID.
Module Definition 1. Clock line for Serial ID.
Module Definition 0. Grounded within the module.
No connection required
Loss of Signal indication. Logic 0 indicates normal operation.
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Inverted DATA out. AC Coupled
Receiver Non-inverted DATA out. AC Coupled
Receiver Ground (Common with Transmitter Ground)
Receiver Power Supply
Transmitter Power Supply
Transmitter Ground (Common with Receiver Ground)
Transmitter Non-Inverted DATA in. AC Coupled.
Transmitter Inverted DATA in. AC Coupled.
Transmitter Ground (Common with Receiver Ground)
Ref.
1
2
3
3
3
4
5
1
1
1
1
1
1
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V.
MOD_DEF(0) pulls line low to indicate module is plugged in.
4. Finisar FTLFxx21xxxxx transceivers operate between OC-3 and OC-48, 1x and 2x Fibre Channel, and
Gigabit Ethernet data rates and respective protocols without active control. Finisar FTLFxx19xxxxx
transceivers operate at 1x and 2x Fibre Channel, and Gigabit Ethernet data rates and respective
protocols without active control.
5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
Towards
Bezel
1
VeeT
2
TXFault
3
TX Disable
4
MOD-DEF(2)
5
MOD-DEF(1)
6
MOD-DEF(0)
7
Rate Select
8
LOS
9
VeeR
10
VeeR
VeeT
20
TD-
19
TD+
18
VeeT
17
VccT
16
VccR
15
VeeR
14
RD+
13
RD-
12
VeeR
11
Towards
ASIC
Diagram of Connector Block Pinout on the Host Board
© Finisar Corporation January 20, 2006 Rev. A
Page 2
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
II.
Absolute Maximum Ratings
Parameter
Maximum Supply Voltage
Storage Temperature
Case Operating Temperature
Relative Humidity
III.
Symbol
Vcc
TS
TOP
RH
Min
-0.5
-40
-10
0
Typ
Max
4.5
85
70
85
Unit
V
°C
°C
%
Ref.
1
Electrical Characteristics (TOP = -10 to 70 °C, VCC = 3.10 to 3.50 Volts)
Parameter
Supply Voltage
Supply Current
Transmitter
Input differential impedance
Single ended data input swing
Transmit Disable Voltage
Transmit Enable Voltage
Transmit Disable Assert Time
Receiver
Single ended data output swing
Data output rise time
Data output fall time
LOS Fault
LOS Normal
Power Supply Rejection
Total Generated Reciever Jitter
(peak to peak)
Total Generated Reciever Jitter
(rms)
Symbol
Vcc
Icc
Rin
Vin,pp
VD
VEN
Vout,pp
tr
tf
VLOS fault
VLOS norm
PSR
JRXp-p
JRXrms
Min
3.10
Typ
230
Max
3.50
300
Unit
V
mA
Ref.
Ω
mV
V
V
us
2
1200
Vcc
Vee+ 0.8
10
4
5
5
6
6
7
0.07
mV
ps
ps
V
V
mVpp
UI
0.007
UI
100
250
Vcc – 1.3
Vee
300
Vcc – 0.5
Vee
100
400
100
100
800
175
175
VccHOST
Vee+0.5
3
Notes:
1. Non condensing.
2. AC coupled
3. Or open circuit.
4. Into 100 ohms differential termination.
5. 20 – 80 %
6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5
MHz up to specified value applied through the power supply filtering network shown on page 23 of the
Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000.
© Finisar Corporation January 20, 2006 Rev. A
Page 3
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
IV.
Optical Characteristics (TOP = -10 to 70°C, VCC = 3.10 to 3.50 Volts)
Parameter
Transmitter
Output Opt. Pwr: 9/125 SMF
Optical Wavelength
Spectral Width (-20dB)
Optical Extinction Ratio
Sidemode Supression ratio
Optical Rise/Fall Time
Total Generated Transmitter Jitter
(peak to peak)
Total Generated Transmitter Jitter
(rms)
Receiver
Average Rx Sensitivity @ 2.67Gb/s
Average Rx Sensitivity @ OC-48
Average Rx Sensitivity @ 2X Fibre
Channel
Average Rx Sensitivity @ Gigabit
Ethernet
Average Rx Sensitivity @ OC-12
Average Rx Sensitivity @ OC-3
Optical Center Wavelength
LOS De-Assert
LOS Assert
LOS Hysteresis
Symbol
Min
POUT
λ
σ
ER
SSRmin
tr/ tf
JTXp-p
-2
1280
Typ
Max
Unit
Ref.
+3
1335
1
1
2
160
0.07
dBm
nm
nm
dB
dB
ps
UI
0.007
UI
9
30
JTXrms
3
RSENS1
RSENS1
RSENS2
-9
-9
-9
-27
-27
-28
dBm
dBm
dBm
3
3
4
RSENS3
-9
-30
dBm
4
RSENS4
RSENS5
λC
LOSD
LOSA
-9
-15
1270
-29
-30
1600
-30
dBm
dBm
nm
dBm
dBm
dB
5
5
-41
0.5
Notes:
1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
2. Unfiltered, 20-80%
3. With worst-case extinction ratio. Measured with a PRBS 231-1 test pattern interspersed with 72
consecutive ones and 72 consecutive zeros.
4. With worst-case extinction ratio. Measured with a PRBS 27-1 test pattern.
5. With worst-case extinction ratio. Measured with a PRBS 223-1 test pattern.
© Finisar Corporation January 20, 2006 Rev. A
Page 4
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
V.
General Specifications
Parameter
Data Rate
Bit Error Rate
Max. Supported Link Length on
9/125μm SMF @ OC-48
Max. Supported Link Length on
9/125μm SMF @ 2X Fibre Channel
Max. Supported Link Length on
9/125μm SMF @ Gigabit Ethernet
Max. Supported Link Length on
9/125μm SMF @ OC-12
Max. Supported Link Length on
9/125μm SMF @ OC-3
Symbol
BR
BER
LMAX1
Min
155
Typ
Max
2667
10-12
Units
Mb/sec
45
km
Ref.
1
2
3
LMAX2
47
km
3
LMAX3
50
km
3
LMAX4
50
km
3
LMAX5
50
km
3
Notes:
1. SONET OC-48 LR-1/SDH STM L-16.1, Gigabit Ethernet and 1x/2x Fibre Channel compliant.
Compatible with SONET OC-12 and OC-3. Supports FEC at 2.67Gb/s.
2. Tested with a PRBS 231-1 test pattern interspersed with 72 consecutive ones and 72 consecutive zeros.
3. Attenuation of 0.55 dB/km is used for the link length calculations (per GR-253 CORE). Distances are
indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link
budget based on specific conditions in your application.
VI.
Environmental Specifications
Finisar SFP transceivers have a commerical operating temperature range from -10°C to
+70°C case temperature.
Parameter
Case Operating Temperature
Storage Temperature
VII.
Symbol
Top
Tsto
Min
-10
-40
Typ
Max
70
85
Units
°C
°C
Ref.
Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations.
These products are certified by TÜV and CSA to meet the Class 1 eye safety
requirements of EN (IEC) 60825 and the electrical safety requirements of
EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
© Finisar Corporation January 20, 2006 Rev. A
Page 5
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
VIII. Digital Diagnostic Functions
Finisar FTLF1721P2xCL SFP transceivers support the 2-wire serial communication
protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in
the GBIC standard, with the same electrical specifications.
The standard SFP serial ID provides access to identification information that describes
the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic
monitoring interface, which allows real-time access to device operating parameters such
as transceiver temperature, laser bias current, transmitted optical power, received optical
power and transceiver supply voltage. It also defines a sophisticated system of alarm and
warning flags, which alerts end-users when particular operating parameters are outside of
a factory set normal range.
The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a
2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic
monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally
defined serial ID memory map remains unchanged. The interface is identical to, and is
thus fully backward compatible with both the GBIC Specification and the SFP Multi
Source Agreement. The complete interface is described in Finisar Application Note AN2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through a 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the
SFP transceiver into those segments of the E2PROM that are not write-protected. The
negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod
Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are organized
as a series of 8-bit data words that can be addressed individually or sequentially.
For more information, please see the SFP MSA documentation1 or Finisar Application
Note AN-2030.
Digital diagnostics for the FTLF1721P2xCL are externally calibrated by default.
Please note that evaluation board FDB-1018 is available with Finisar ModDEMO
software that allows simple to use communication over the 2-wire serial interface.
© Finisar Corporation January 20, 2006 Rev. A
Page 6
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
IX.
Mechanical Specifications
Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the
dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.
FTLF1721P2BCL
© Finisar Corporation January 20, 2006 Rev. A
Page 7
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
FTLF1721P2WCL
© Finisar Corporation January 20, 2006 Rev. A
Page 8
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
X.
PCB Layout and Bezel Recommendations
© Finisar Corporation January 20, 2006 Rev. A
Page 9
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
© Finisar Corporation January 20, 2006 Rev. A
Page 10
FTLF1721P2xCL Pluggable SFP Product Specification – January 2006
XI.
References
1.
Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),
September 2000. Documentation is currently available at Finisar upon request.
2.
Bellcore GR-253 and ITU-T G.957 Specifications (Transmitter Optical Output
Power complies with SONET OC-48 requirements only).
3.
IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-LX.
IEEE Standards Department, 2002. (*)
4.
“Fibre Channel Draft Physical Interface Specification (FC-PI-2 Rev. 7.0)”.
American National Standard for Information Systems. (*)
5.
Directive 2002/95/EC of the European Council Parliament and of the Council,
“on the restriction of the use of certain hazardous substances in electrical and
electronic equipment.” January 27, 2003.
(*) Neither IEEE 802.3 nor FC-PI-2 Rev. 7.0 specifies a 1310nm DFB single mode
interface. The FTLF1721P2xCL complies with these specifications except for
transmitter wavelength, receiver sensitivity, and transmit output power. See Section IV
for details.
XII.
For More Information
Finisar Corporation
1389 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. 1-408-548-1000
Fax 1-408-541-6138
[email protected]
www.finisar.com
© Finisar Corporation January 20, 2006 Rev. A
Page 11