Finisar Product Specification Short-Wavelength GBIC Transceiver FTR-8519-3D Product Features • Up to 1.25Gb/s bi-directional data links • 850nm VCSEL Laser Transmitter • Optional Digital Diagnostics Functions • Extended Operating Temperature Range (-10°C to +85°C) • Compatible with 3.3V & 5V Systems • Hot-Pluggable (complies with GBIC specification Rev. 5.5) • Fully metallic enclosure for low EMI • Low power dissipation Applications • • 1.0625Gb/s Fibre Channel 1.25 Gigabit Ethernet Finisar’s FTR-8519-3D 850nm GBIC transceivers comply with GBIC Specification Revision 5.51. They are compatible with the Gigabit Ethernet as specified in IEEE Std 802.32, Fibre Channel FC-PH, PH2, PH33 and FC-PI 13.04. Product Selection Part Number FTR-8519-3D FTR-8519-3D-DD © Finisar Corporation November 16, 2007 Rev. E3 Digital Diagnostics? No Yes Page 1 F i n i s a r FTR-8519-3D GBIC Product Specification – November 2007 I. Pin Out Pin Name Pin # Sequence RX_LOS 1 2 GND 2 2 GND 3 2 MOD_DEF(0) 4 2 MOD_DEF(1) 5 2 MOD_DEF(2) 6 2 TX_DISABLE 7 2 GND 8 2 GND 9 2 TX_FAULT (not supported) GND 10 2 11 1 -RX_DAT 12 1 +RX_DAT 13 1 GND 14 1 VCC 15 2 VCC 16 2 GND 17 1 +TX_DAT 18 1 -TX_DAT 19 1 GND 20 1 Table 1. GBIC to host connector pin assignment “Sequence” indicates the order in which pins make contact when the device is hot plugged. Also see “Table 3: Signal Definitions” in the GBIC Specification Revision 5.5.1 II. Electrical Power Interface © Finisar Corporation November 16, 2007 Rev. E3 Page 2 F i n i s a r FTR-8519-3D GBIC Product Specification – November 2007 Finisar FTR-8519-3D GBICs have an extended power supply voltage range of 3.15 V to 5.5 V as described in Table 2. They are compatible with both 3.3V and 5 V systems. +5/3.3 Volt Electrical Power Interface Parameter Supply Current Surge Current Symbol Is Isurge Min Absolute Supply Voltage Vmax Operating Supply Voltage Vcc Typ 190 Max 300 330 Units mA mA Notes/Conditions -0.3 6 V Not to be applied continuously 3.15 5.5 V Hot plug Table 2. Electrical power interface III. Low Speed Signals RX_LOS, and TX_DISABLE are TTL signals as described in Table 3. MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VI, “Serial Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. If host_Vcc is 3.3V, then they must be pulled to 3.3V. If host_Vcc is 3.3V, do not pull the MOD_DEF pins to 5V. For more detailed information, see sections 5.3.1 – 5.3.8 in the GBIC Specification Rev. 5.51. Low Speed Signals, Electronic Characteristics Parameter GBIC Output LOW Symbol VOL GBIC Output HIGH VOH GBIC Input LOW VIL GBIC Input HIGH VIH Min 0 Max 0.5 Units Notes/Conditions V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector host_Vcc - 0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector* 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector* *Note VIH and VIL are the same for both 5V and 3.3V operation Table 3. Low speed signals – electronic characteristics © Finisar Corporation November 16, 2007 Rev. E3 Page 3 F i n i s a r FTR-8519-3D GBIC Product Specification – November 2007 Low Speed Signal Parameters Parameter Symbol RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay Min Typ --30 --0.5 t_loss_on RX_LOS Negate Delay TX_DISABLE Assert Time TX_DISABLE Negate Time TX_DISABLE Reset Time Max Units Notes/Conditions dBm dBm dB 44 100 μsec From detection of loss of signal to assertion of RX_LOS t_loss_off 44 100 μsec From detection of presence of signal to negation of RX_LOS t_off 10 μsec Rising edge of TX_DISABLE to fall of output signal below 10% of nominal t_on 1000 μsec Falling edge of TX_DISABLE to rise of output signal above 90% of nominal t_reset 10 μsec TX_DISABLE HIGH before TX_DISABLE set LOW Table 4. Low speed signal parameters -19 IV. High Speed Electrical Interface All high-speed PECL signals are AC-coupled internally. High Speed Electrical Interface Parameter Data Input Voltage Data Output Voltage PECL rise/fall Bit Error Rate Tx Input Impedance Rx Output Impedance Symbol Vin Vout tr,tf BER Zin Zout Min 650 370 Typ 75 75 Max 2000 2000 260 10-12 Units mV mV psec Notes/Conditions PECL differential peak - peak PECL differential peak - peak 20%-80% differential PRBS 27 - 1 test data pattern ohm ohm Table 5. High-speed electrical interface © Finisar Corporation November 16, 2007 Rev. E3 Page 4 F i n i s a r FTR-8519-3D GBIC Product Specification – November 2007 V. Optical Parameters Optical Parameters Parameter Transmitter Center Wavelength Transmitter Spectral Width (RMS) Transmitter Optical Output Power Transmitter Extinction Ratio Relative Intensity Noise Transmitter Eye Opening Total Transmitter Jitter Symbol λc Δλ Pout OMI RIN -- Min 820 -9.5 9 Typ 850 0.5 Max 860 0.85 -3.5 -117 60 TJTX 180 Transmitter Rise/Fall Time Optical Input Wavelength Optical Receiver Sensitivity Tr/Tf λin RXSENS 210 860 -19 Average Received Power Max Reflectivity Total Receiver Jitter RXMAX TJRX 770 0 -14 180 Units nm nm dBm dB dB/Hz % ps Notes/Conditions RMS Average Power Conforms to IEEE 802.3 and Fibre Channel Eye Masks Peak to peak, filtered ps Unfiltered 20%-80% nm dBm BER < 10-12 w/ PRBS 27 - 1 test data pattern @ 1.25Gb/s dBm dB ps Peak to peak, filtered in loopback Table 6. Optical parameters VI. General Specifications General Parameter Data Rate Fiber Length Fiber Length Symbol Min Typ Max Units Notes/Conditions BR 1.25, 1.0625 Gb/sec Fibre Channel, IEEE 802.3 Compatible. Rate tolerance = ±100ppm L 550 m 50μm 500MHz-km Fiber L 275 m 62.5μm 200MHz-km Fiber Table 7. General specifications © Finisar Corporation November 16, 2007 Rev. E3 Page 5 F i n i s a r FTR-8519-3D GBIC Product Specification – November 2007 VII. Environmental Specifications Note that the GBIC Specification requires an ambient temperature range of 0 to 50°C. Finisar GBICs have an extended range from –10°C to +85°C case temperature as specified in Table 8. Environment Parameter Symbol Min Top RH Tsto -- -10 0 -40 Operating Temp Relative Humidity Storage Temp Eye Safety Typ Max 85 85 85 Units Notes/Conditions °C % °C Case Temperature Non Condensing CDRH and IEC-825 Class 1 Laser Product Table 8. Environmental Specifications VIII. Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for ‘Module Definition “4”’ as outlined in Annex D of the GBIC Specification 1. These GBICs use an Atmel AT24C01A 128 byte E2PROM at address A0H. For details on interfacing with the E2PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM.”5 I2C Timing Requirements Parameter Atmel I2C Clock Rate Symbol Catmel Min 0 Typ Max 100,000 Units Notes/Conditions Hz Bus can be driven blind. Table 9. I2C timing requirements © Finisar Corporation November 16, 2007 Rev. E3 Page 6 FTR-8519-3D GBIC Product Specification – November 2007 X. F i n i s a r Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5.5, Section 61. Insertion, Extraction, and Retention Forces Parameter GBIC insertion GBIC extraction GBIC retention Symbol Min Typ Max Units Notes/Conditions FI 0 20 Newtons ~4.5 lbs FE 0 15 Newtons ~3.3 lbs FR 130 N/A Newtons Straight out ~29.3 lbs Table 10. Insertion, extraction, and retention forces FTR-8519-3D Figure 1. GBIC Outline Drawing © Finisar Corporation November 16, 2007 Rev. E3 Page 7 FTR-8519-3D GBIC Product Specification – November 2007 F i n i s a r XI. References 1. “Gigabit Interface Converter (GBIC) Revision 5.5”. Sun Microsystems Computer Company et. al., September 27, 2000. http://playground.sun.com/pub/OEmod/ 2. IEEE Std 802.3. IEEE Standards Department, 2002. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. American National Standard for Information Systems. 4. Fibre Channel Draft Physical Interface Specification (FC-PI 13.0). American National Standard for Information Systems. 5. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”. Atmel Corporation. www.Atmel.com XI. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1134 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation November 16, 2007 Rev. E3 Page 8