Finisar Product Specification Long-Wavelength GBIC Transceiver FTR-1319-3D Product Features • Up to 1.25Gb/s bi-directional data links • 1310nm Fabry-Perot laser transmitter • Optional Digital Diagnostics • Extended operating temperature range (-10°C to +85°C) • Compatible with 3.3 & 5V systems • Hot-pluggable (complies with GBIC specification Rev. 5.5) • Fully metallic enclosure for low EMI • Low power dissipation Applications • • 1.0625 Gb/s Fibre Channel 1.25 Gigabit Ethernet Finisar’s FTR-1319-3D 1310nm GBIC transceivers comply with GBIC Specification Revision 5.51. They are compatible with Gigabit Ethernet as specified in IEEE 802.32, Fibre Channel FC-PH, PH2, PH33 and FC-PI 13.04. Product Selection Part Number FTR-1319-3D FTR-1319-3D-DD © Finisar Corporation November 16, 2007 Rev. H3 Digital Diagnostics? No Yes Page 1 FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 I. Finisar Pin Out Pin Name Pin # Sequence RX_LOS 1 2 GND 2 2 GND 3 2 MOD_DEF(0) 4 2 MOD_DEF(1) 5 2 MOD_DEF(2) 6 2 TX_DISABLE 7 2 GND 8 2 GND 9 2 TX_FAULT (not supported) GND 10 2 11 1 -RX_DAT 12 1 +RX_DAT 13 1 GND 14 1 VCC 15 2 VCC 16 2 GND 17 1 +TX_DAT 18 1 -TX_DAT 19 1 GND 20 1 Table 1. GBIC to host connector pin assignment “Sequence” indicates the order in which pins make contact when the device is hot plugged. See “Table 3: Signal Definitions” in the GBIC Specification Revision 5.5.1 © Finisar Corporation November 16, 2007 Rev. H3 Page 2 Finisar FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 II. Electrical Power Interface Finisar FTR-1319-3D GBICs have an extended power supply voltage range of 3.15 V to 5.5 V as described in Table 2. They are compatible with both 3.3V and 5 V systems. Parameter Symbol Min Typ Max Units 200 300 +30 mA mA Supply Current Inrush Current Is Isurge Absolute Supply Voltage Vmax -0.3 6 V Operating Supply Voltage Vcc 3.15 5.5 V Notes/Conditions Hot plug, above steady state current. Not to be applied continuosly Referenced to GND Table 2. Electrical power interface III. Low Speed Signals RX_LOS and TX_DISABLE are TTL signals as described in Table 3. MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VIII, “Serial Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. For more detailed information, see sections 5.3.1 – 5.3.8 in the GBIC Specification Rev. 5.51. Parameter GBIC Output LOW GBIC Output HIGH GBIC Input LOW GBIC Input HIGH Symbol Min Max VOL 0 0.5 Units Notes/Conditions 4.7k to 10k pull-up to host_Vcc, measured at host side of connector VOH host_Vcc - 0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector VIL 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector Table 3. Low speed signals – electronic characteristics © Finisar Corporation November 16, 2007 Rev. H3 V Page 3 Finisar FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 Parameter Symbol Min Typ Max RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay --31 --0.5 t_loss_on 100 RX_LOS Negate Delay t_loss_off 100 TX_DISABLE Assert Time t_off 10 TX_DISABLE Negate Time t_on 1000 TX_DISABLE Reset Time t_reset -20 10 Units Notes/Conditions dBm dBm dB µsec From detection of loss of signal to assertion of RX_LOS µsec From detection of presence of signal to negation of RX_LOS µsec Rising edge of TX_DISABLE to fall of output signal below 10% of nominal µsec Falling edge of TX_DISABLE to rise of output signal above 90% of nominal µsec TX_DISABLE HIGH before TX_DISABLE set LOW Table 4. Low speed signal parameters IV. High Speed Electrical Interface All high-speed PECL signals are AC-coupled internally. Parameter Symbol Min Data Input Voltage Data Output Voltage PECL rise/fall Bit Error Rate Tx Input Impedance Vin Vout tr,tf BER Zin 650 370 Rx Output Impedance Zout Typ Max Units Notes/Conditions 2000 2000 260 10-12 mV mV psec PECL differential peak - peak PECL differential peak - peak 20%-80% differential PRBS 27 - 1 test data pattern 75 Ohm 75 Ohm Table 5. High-speed electrical interface © Finisar Corporation November 16, 2007 Rev. H3 Page 4 Finisar FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 V. Optical Parameters Parameter Symbol TRANSMITTER CHARACTERISTICS Transmitter Center Wavelength λc Transmitter Spectral Width ΔλRMS Min Typ Max 1270 1310 1355 4 RMS. Also meets curves in FC-PI 10.0 Figures 18. dBm Average power coupled into single mode fiber dB % Conforms to IEEE 802.3 and Fibre Channel Eye Masks Pout -9 Transmitter Extinction Ratio Transmitter Eye Opening OMI -- 9 60 Transmitter Rise/Fall Time tr /tf 260 ps RIN 160 -120 ps dB / Hz RECEIVER CHARACTERISTICS Optical Input Wavelength Receiver Reflectance Optical Input Power (1.25GB/s) Optical Input Power (1.0625Gb/s) Total Receiver Jitter λin RRX Pin Pin 1270 -3 nm nm Transmitter Optical Output Power Total Transmitter Jitter Relative Intensity Noise -6 Units Notes/Conditions 20%-80% differential unfiltered Peak to peak, filtered 1355 -14 -3 -3 160 nm dB -19 dBm BER < 10-12 w/ PRBS 7 -20 dBm 2 - 1 test pattern ps Peak to peak, filtered in loopback Note: Parameters are specified over temperature and voltage, at end of life unless otherwise noted. Table 6. Optical parameters VI. General Specifications Parameter Data Rate Fiber Length Fiber Length Fiber Length Symbol Min BR L L L Typ Max Units Notes/Conditions 1.25 1.0625 Gb/sec Fibre Channel, IEEE 802.3 Compatible 10,000 m 9μm Core Single Mode Fiber 550 m 50μm 500MHz-km Fiber 275 m 62.5μm 200MHz-km Fiber Table 7. General specifications © Finisar Corporation November 16, 2007 Rev. H3 Page 5 FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 Finisar VII. Environmental Specifications Note that the GBIC Specification requires an ambient temperature range of 0 to 50°C. The FTR-1319-3D has an extended range from –10°C to +85°C case temperature as specified in Table 8. Parameter Symbol Min Top RH Tsto -- -10 0 -40 Operating Temp Relative Humidity Storage Temp Eye Safety Typ Max Units Notes/Conditions 85 85 85 °C % °C Case Temperature Non Condensing CDRH and IEC-825 Class 1 Laser Product. See Note 1 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. Table 8. Environmental specifications VIII. Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for ‘Module Definition “4”’ as outlined in Annex D of the GBIC Specification 1. These GBICs use an Atmel AT24C01A 128 byte E2PROM at address A0H. For details on interfacing with the E2PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM.” 5 Parameter I2C Clock for Atmel (A0H) and Controller IC (A2H) Symbol Min Catmel 0 Typ Max 100,000 Units Notes/Conditions Hz Bus can be driven blind Table 9. I2C timing requirements © Finisar Corporation November 16, 2007 Rev. H3 Page 6 FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 Finisar IX. Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5.5, Section 61. Insertion, Extraction, and Retention Forces Parameter GBIC insertion GBIC extraction GBIC retention Symbol Min Typ Max Units Notes/Conditions FI 0 20 Newtons ~4.5 lbs FE 0 15 Newtons ~3.3 lbs FR 130 N/A Newtons Straight out ~29.3 lbs Table 10. Insertion, extraction, and retention forces Figure 1. GBIC outline drawing © Finisar Corporation November 16, 2007 Rev. H3 Page 7 FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 Finisar X. References 1. “Gigabit Interface Converter (GBIC) Revision 5.5”. Sun Microsystems Computer Company et. al., August 16, 1999. http://playground.sun.com/pub/OEmod/ 2. IEEE Std 802.3. IEEE Standards Department, 2002. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. American National Standard for Information Systems. 4. “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0). American National Standard for Information Systems. 5. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”. Atmel Corporation. www.Atmel.com XI. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1134 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation November 16, 2007 Rev. H3 Page 8