Finisar Preliminary Product Specification DWDM SFP Transceiver FWDM-1629-XX PRODUCT FEATURES • Up to 1.25 Gb/s bi-directional data links • Hot-pluggable SFP footprint • Temperature-stabilized DWDMrated DFB laser transmitter • 100GHz ITU Grid, C Band • Low dispersion DFB laser suitable • Metal enclosure for low EMI • Extended operating range: -5°C to 70°C case temperature • Wavelength controlled within ± 0.1 nm over life and temperature • Amplified DWDM networks Bandwidth aggregation • • Extended link budget with APD receiver technology • Ring topologies with OADM • GbE and 1X FC compliant APPLICATIONS Finisar’s Dense Wavelength-Division Multiplexing (DWDM) transceivers offer DWDM transport with dramatically lower power and cost in a standard pluggable Small Form Factor Pluggable (SFP) package. The FWDM-1629 is designed expressly for service providers deploying DWDM networking equipment in metropolitan Ethernet and SAN networks. The fiber link budget has been enhanced to 30dB with an Avalanche Photo Diode (APD) receiver. In addition, digital diagnostic features are implemented as described in Finisar Application Note AN-2030, “Digital Diagnostic Monitoring Interface for Optical Transceivers”2. Finisar Corporation Rev C, February 2005 PRELIMINARY and Confidential Page 1 Finisar PRODUCT SELECTION Product Code FWDM -1629-17 FWDM -1629-18 FWDM -1629-19 FWDM -1629-20 FWDM -1629-21 FWDM -1629-22 FWDM -1629-23 FWDM -1629-24 FWDM -1629-25 FWDM -1629-26 FWDM -1629-27 FWDM -1629-28 FWDM -1629-29 FWDM -1629-30 FWDM -1629-31 FWDM -1629-32 FWDM -1629-33 FWDM -1629-34 FWDM -1629-35 FWDM -1629-36 FWDM -1629-37 FWDM -1629-38 FWDM -1629-39 FWDM -1629-40 FWDM -1629-41 FWDM -1629-42 FWDM -1629-43 FWDM -1629-44 FWDM -1629-45 FWDM -1629-46 FWDM -1629-47 FWDM -1629-48 FWDM -1629-49 FWDM -1629-50 FWDM -1629-51 FWDM -1629-52 FWDM -1629-53 FWDM -1629-54 FWDM -1629-55 FWDM -1629-56 FWDM -1629-57 FWDM -1629-58 FWDM -1629-59 FWDM -1629-60 FWDM -1629-61 Finisar Corporation Rev C, February 2005 Frequency (THz) 191.7 191.8 191.9 192.0 192.1 192.2 192.3 192.4 192.5 192.6 192.7 192.8 192.9 193.0 193.1 193.2 193.3 193.4 193.5 193.6 193.7 193.8 193.9 194.0 194.1 194.2 194.3 194.4 194.5 194.6 194.7 194.8 194.9 195.0 195.1 195.2 195.3 195.4 195.5 195.6 195.7 195.8 195.9 196.0 196.1 PRELIMINARY and Confidential Center Wavelength (nm) 1563.86 1563.05 1562.23 1561.42 1560.61 1559.79 1558.98 1558.17 1557.36 1556.55 1555.75 1554.94 1554.13 1553.33 1552.52 1551.72 1550.92 1550.12 1549.32 1548.51 1547.72 1546.92 1546.12 1545.32 1544.53 1543.73 1542.94 1542.14 1541.35 1540.56 1539.77 1538.98 1538.19 1537.40 1536.61 1535.82 1535.04 1534.25 1533.47 1532.68 1531.90 1531.12 1530.33 1529.55 1528.77 Page 2 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 I. Finisar Pin Descriptions Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ 19 20 TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault Transmitter Disable. Laser output disabled on high or open Module Definition 2. Data line for Serial ID Module Definition 1. Clock line for Serial ID Module Definition 0. Grounded within the module No connection required Loss of Signal indication. Logic 0 indicates normal operation Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. 100 ohm termination between TD+ and TD-, AC Coupled thereafter Transmitter Inverted DATA in. See TD+ Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 5.5V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar 2x receiver achieves simultaneous 1x and 2x operation without active control. 5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 5.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Towards Bezel Finisar Corporation Rev C, February 2005 1 VeeT 2 TXFault 3 TX Disable 4 MOD-DEF(2) 5 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 VeeR VeeT 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 PRELIMINARY and Confidential Towards ASIC Page 3 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 Finisar Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature III. Symbol Vcc TS TOP Min -0.5 -10 -5 Unit V °C °C Ref. Max 4.7 85 70 Max 3.50 305 Icc+30 1.0 Unit V mA mA W Ref. 1200 Vcc Vee+ 0.8 Ω mV V V 1 250 Vcc – 1.3 Vee 2 175 1000 150 150 VccHOST mV ps ps V 3 4 4 5 Vee+0.5 V mVpp 5 6 Electrical Characteristics (TOP = -5 to 70 °C, VCC = 3.13 to 3.50 Volts) Parameter Supply Voltage Supply Current Inrush Current Maximum Power TRANSMITTER Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage RECEIVER Single ended data output swing Data output rise time Data output fall time LOS Fault Vout,pp tr tf VLOSfault Vcc – 0.5 LOS Normal Power Supply Rejection VLOS norm PSR Vee 100 Notes: 1. 2. 3. 4. 5. 6. Typ Symbol Vcc Icc Isurge Pmax Rin Vin,pp VD VEN Min 3.13 Typ 3.30 100 Connected directly to TX data input pins. AC coupled thereafter. Or open circuit. Into 100 ohms differential termination. 20 – 80 % Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. Finisar Corporation Rev C, February 2005 PRELIMINARY and Confidential Page 4 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 IV. Finisar Low Speed Signals Parameter Symbol Min Typ Max -42 -36 -34 2 -32 RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay t_loss_on 100 RX_LOS Negate Delay t_loss_off 100 TX_DISABLE Assert Time t_off 10 TX_DISABLE Negate Time t_on 1000 TX_DISABLE Reset Time TX_FAULT Assert Finisar Corporation Rev C, February 2005 0.5 t_reset 10 -0.2 +0.2 Units Notes/Conditions dBm dBm dB µsec From detection of loss of signal to assertion of RX_LOS µsec From detection of presence of signal to negation of RX_LOS µsec Rising edge of TX_DISABLE to fall of output signal below 10% of nominal Falling edge of TX_DISABLE µsec to rise of output signal above 90% of nominal. Time indicated is under steady-state temperature conditions. µsec TX_DISABLE HIGH before TX_DISABLE set LOW nm TX_Fault will assert before the device is outside of specified wavelength range PRELIMINARY and Confidential Page 5 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 V. Finisar Optical Parameters Parameter Symbol Min TRANSMITTER CHARACTERISTICS Center Wavelength Spacing Spectral Width Transmitter Center Wavelength – End of Life Transmitter Center Wavelength – Start of Life Side Mode Suppression Ratio (SMSR) Optical Rise/Fall Time Transmitter Optical Output Power Units Notes/Conditions λc X - 100 X X + 100 pm λc Y - 25 Y Y + 25 pm Corresponds to approximately 0.8 nm Full width, -20dB from max X = specified center wavelength Y = X – 60pm SMSR 30 dB Modulated tr / tf Pout 0 ∆λ 20 OMI Relative Intensity Noise Dispersion Penalty at 180km RECEIVER CHARACTERISTICS Optical Input Wavelength RIN Pin GHz 0.2 0.3 nm 200 +4 9.0 40 -120 3.0 1520 Receiver Jitter Generation OSNR Limit OSNR Penalty Max 100 Transmitter Extinction Ratio Transmitter Eye Opening Optical Input Power (BER < 10 -9) Optical Input Power (BER < 10 -12) Optical Input Power – Receiver Damage Threshold Receiver Reflectance Typ 1570 nm 100 ps Pin -32 -9 Pin -30 -9 6 RRX OSNRmin ps Unfiltered, 80% -20% dBm Average power coupled into single mode fiber dB % IEEE 802.3 and Fibre Channel Eye Mask Margin dB/Hz dB 3600ps/nm. See Note 3. Peak to peak, -25 dBm Rx power dBm 1.25 Gb/s w/ PRBS 2 7 -1 dBm 1.25 Gb/s w/ PRBS 2 7 -1 dBm -27 dB 2.0 dB dB 20 For OSNR = OSNRmin. See Note 4. Notes: 1. Parameters are specified over temperature and voltage, at end of life unless otherwise noted. 2. All parameters are measured on a Finisar SFP Evaluation Card unless otherwise noted. 3. Dispersion penalty is measured in loop back with OSNR set at Rx < 28 dB. Data rate and pattern used same as specified for Optical Input Power. Dispersion penalty is measured at BER = 10-10 4. OSNR penalty is measured in loop back. Data rate and pattern used is same as specified for Optical Input Power. OSNR penalty is measured at BER = 10-10 Finisar Corporation Rev C, February 2005 PRELIMINARY and Confidential Page 6 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 Finisar VI. Wavelength Stabilization The laser transmitter will not be turned on until its temperature is adjusted to ensure operation within the specified channel (X +/- 0.4nm). This temperature stabilization time is dependent on the ambient temperature conditions, but will typically occur within 90 seconds of powering the device. The device will transmit within the specified wavelength tolerance (X +/- 0.1nm) within 5 seconds of transmitter operation. VII. General Specifications Parameter Symbol Min Data Rate BR 1.06 1.25 Max Units Notes/Conditions 1.25 Gb/sec Fibre Channel, IEEE 802.3 compatible Total System Budget 30 32 dB @ 1.25 Gb/s, BER <10-12 w/ PRBS 2-7-1. See Note 1 Note 1: Total system budget is defined as Pout – Pin – typical connector losses. VIII. Environmental Specifications Parameter Operating Temp Symbol Min Top -5 Typ Max Case temperature measured on top-side of device Storage Temp Tsto -10 85 °C Ambient temperature Eye Safety CDRH and IEC-825 Class 1 Laser Product. See Note 1 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. Finisar Corporation Rev C, February 2005 70 Units Notes/Conditions °C PRELIMINARY and Confidential Page 7 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 Finisar IX. Serial Communication Protocol All Finisar SFPs support the 2-wire serial communication protocol outlined in the SFP MSA1. These SFPs use an Atmel AT24C01A 128 byte E2PROM with an address of A0h. For details on interfacing with the E2PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM.”4 Finisar’s DWDM SFPs also support extended diagnostic features as described in Finisar Applications Note AN-2030, “Digital Diagnostic Monitoring Interface for Optical Transceivers”2. A controller IC that monitors system parameters such as laser current, module temperature, transmitter power, and received power is accessible at address A2H. Parameter I2C Clock for Atmel (A0H) and Controller IC (A2H) Symbol Min Catmel 0 Typ Max Units Notes/Conditions 100,000 Hz Bus can be driven blind. ( E2PROM Description TBD pending MSA) Finisar Corporation Rev C, February 2005 PRELIMINARY and Confidential Page 8 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 X. Finisar Mechanical Specifications Finisar’s Multi-rate DWDM Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA). Figure 1. DWDM SFP Outline Drawing Finisar Corporation Rev C, February 2005 PRELIMINARY and Confidential Page 9 FWDM-1629-XX DWDM SFP Preliminary Product Specification – February 2005 Finisar XI. Ordering Information Part Number FWDM-1629-XX Description DWDM SFP with APD Receiver XX = channel number (see product selection on page 2) XII. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available from Finisar upon request. 2. “Application Note AN-2030: Digital Diagnostic Monitoring Interface for Optical Transceivers”, Finisar Corporation, April 2002. 3. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”, Atmel Corporation. www.Atmel.com 4. “Digital Diagnostic Monitoring Interface For Optical Transceivers Rev 6.1”, September, 2004. Documentation is currently available from Finisar upon request. For More Information: Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. (408) 548-1000 Fax (408) 541-6138 [email protected] www.finisar.com Finisar Corporation Rev C, February 2005 PRELIMINARY and Confidential Page 10