LM139,LM239,LM2901,LM3302,LM339 LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators Literature Number: SNOSBJ3C LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators General Description Features The LM139 series consists of four independent precision voltage comparators with an offset voltage specification as low as 2 mV max for all four comparators. These were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. These comparators also have a unique characteristic in that the input common-mode voltage range includes ground, even though operated from a single power supply voltage. n n n n n Application areas include limit comparators, simple analog to digital converters; pulse, squarewave and time delay generators; wide range VCO; MOS clock timers; multivibrators and high voltage digital logic gates. The LM139 series was designed to directly interface with TTL and CMOS. When operated from both plus and minus power supplies, they will directly interface with MOS logic — where the low power drain of the LM339 is a distinct advantage over standard comparators. n n n n n n n Wide supply voltage range LM139/139A Series 2 to 36 VDC or ± 1 to ± 18 VDC LM2901: 2 to 36 VDC or ± 1 to ± 18 VDC LM3302: 2 to 28 VDC or ± 1 to ± 14 VDC Very low supply current drain (0.8 mA) — independent of supply voltage Low input biasing current: 25 nA ± 5 nA Low input offset current: ± 3 mV Offset voltage: Input common-mode voltage range includes GND Differential input voltage range equal to the power supply voltage Low output saturation voltage: 250 mV at 4 mA Output voltage compatible with TTL, DTL, ECL, MOS and CMOS logic systems Advantages n n n n n n High precision comparators Reduced VOS drift over temperature Eliminates need for dual supplies Allows sensing near GND Compatible with all forms of logic Power drain suitable for battery operation One-Shot Multivibrator with Input Lock Out 00570612 © 2004 National Semiconductor Corporation DS005706 www.national.com LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators March 2004 LM139/LM239/LM339/LM2901/LM3302 Distributors for availability and specifications. Absolute Maximum Ratings (Note 10) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ LM139/LM239/LM339 LM139A/LM239A/LM339A LM3302 LM2901 Supply Voltage, V+ 36 VDC or ± 18 VDC 28 VDC or ± 14 VDC 36 VDC 28 VDC −0.3 VDC to +36 VDC −0.3 VDC to +28 VDC 50 mA 50 mA Molded DIP 1050 mW 1050 mW Cavity DIP 1190 mW Small Outline Package 760 mW Differential Input Voltage (Note 8) Input Voltage Input Current (VIN < −0.3 VDC), (Note 3) Power Dissipation (Note 1) Output Short-Circuit to GND, (Note 2) Storage Temperature Range Continuous Continuous −65˚C to +150˚C −65˚C to +150˚C Lead Temperature (Soldering, 10 seconds) 260˚C 260˚C Operating Temperature Range −40˚C to +85˚C LM339/LM339A 0˚C to +70˚C LM239/LM239A −25˚C to +85˚C LM2901 −40˚C to +85˚C LM139/LM139A −55˚C to +125˚C Soldering Information Dual-In-Line Package Soldering (10 seconds) 260˚C 260˚C Vapor Phase (60 seconds) 215˚C 215˚C Infrared (15 seconds) 220˚C 220˚C Small Outline Package See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices. ESD rating (1.5 kΩ in series with 100 pF) 600V 600V Electrical Characteristics (V+=5 VDC, TA = 25˚C, unless otherwise stated) Parameter Conditions LM139A Min Typ LM239A, LM339A Max Min Typ LM139 Max Min Typ Units Max Input Offset Voltage (Note 9) 1.0 2.0 1.0 2.0 2.0 5.0 mVDC Input Bias Current IIN(+) or IIN(−) with Output in 25 100 25 250 25 100 nADC 25 5.0 50 3.0 25 nADC Linear Range, (Note 5), VCM=0V Input Offset Current Input Common-Mode Voltage Range Supply Current IIN(+)−IIN(−), VCM=0V + V =30 VDC (LM3302, 3.0 + 0 V −1.5 + 0 V −1.5 + 0 V −1.5 VDC V+ = 28 VDC) (Note 6) RL = ∞ on all Comparators, 0.8 2.0 RL = ∞, V+ = 36V, 0.8 2.0 0.8 2.0 mADC 1.0 2.5 1.0 2.5 mADC (LM3302, V+ = 28 VDC) Voltage Gain RL≥15 kΩ, V+ = 15 VDC 50 200 50 200 50 200 V/mV 300 ns VO = 1 VDC to 11 VDC Large Signal Response Time www.national.com VIN = TTL Logic Swing, VREF = 300 1.4 VDC, VRL = 5 VDC, 2 300 (Continued) (V+=5 VDC, TA = 25˚C, unless otherwise stated) Parameter Conditions LM139A Min Typ LM239A, LM339A Max Min Typ Max LM139 Min Typ Units Max RL = 5.1 kΩ Response Time VRL = 5 VDC, RL = 5.1 kΩ, Output Sink Current VIN(−) = 1 VDC, VIN(+) = 0, 1.3 1.3 1.3 µs 16 mADC (Note 7) 6.0 16 6.0 16 6.0 VO ≤ 1.5 VDC Saturation Voltage VIN(−) = 1 VDC, VIN(+) = 0, 250 400 250 400 250 400 mVDC ISINK ≤ 4 mA Output Leakage Current VIN(+) = 1 VDC,VIN(−) = 0, 0.1 0.1 0.1 nADC VO = 5 VDC Electrical Characteristics (V+ = 5 VDC, TA = 25˚C, unless otherwise stated) Parameter Conditions LM239, LM339 Min Typ LM2901 Max Min Typ LM3302 Max Min Typ Units Max Input Offset Voltage (Note 9) 2.0 5.0 2.0 7.0 3 20 mVDC Input Bias Current IIN(+) or IIN(−) with Output in 25 250 25 250 25 500 nADC Input Offset Current IIN(+)−IIN(−), VCM = 0V Input Common-Mode V+ = 30 VDC (LM3302, Linear Range, (Note 5), VCM=0V Voltage Range Supply Current 5.0 50 V+−1.5 0 5 50 V+−1.5 0 3 0 100 nADC V+−1.5 VDC + V = 28 VDC) (Note 6) RL = ∞ on all Comparators, 0.8 2.0 0.8 2.0 0.8 2.0 mADC RL = ∞, V+ = 36V, 1.0 2.5 1.0 2.5 1.0 2.5 mADC (LM3302, V+ = 28 VDC) Voltage Gain RL ≥ 15 kΩ, V+ = 15 VDC 50 200 25 100 2 30 V/mV VO = 1 VDC to 11 VDC Large Signal Response Time VIN = TTL Logic Swing, VREF = 300 300 300 ns 1.3 1.3 1.3 µs 16 mADC 1.4 VDC, VRL = 5 VDC, RL = 5.1 kΩ, Response Time VRL = 5 VDC, RL = 5.1 kΩ, Output Sink Current VIN(−)= 1 VDC, VIN(+) = 0, (Note 7) 6.0 16 6.0 16 6.0 VO ≤ 1.5 VDC Saturation Voltage VIN(−) = 1 VDC, VIN(+) = 0, Output Leakage VIN(+) = 1 VDC,VIN(−) = 0, 250 400 250 400 250 500 mVDC ISINK ≤ 4 mA Current 0.1 0.1 0.1 nADC LM139 Units VO = 5 VDC Electrical Characteristics (V+ = 5.0 VDC, (Note 4)) Parameter Conditions LM139A Min Typ Max LM239A, LM339A Min Typ Max Min Typ Max Input Offset Voltage (Note 9) 4.0 4.0 9.0 Input Offset Current IIN(+)−IIN(−), VCM = 0V 100 150 100 mVDC nADC Input Bias Current IIN(+) or IIN(−) with Output in 300 400 300 nADC Input Common-Mode V+=30 VDC (LM3302, V+−2.0 VDC Voltage Range V+ = 28 VDC) (Note 6) Linear Range, VCM = 0V (Note 5) 0 3 V+−2.0 0 V+−2.0 0 www.national.com LM139/LM239/LM339/LM2901/LM3302 Electrical Characteristics LM139/LM239/LM339/LM2901/LM3302 Electrical Characteristics (Continued) (V+ = 5.0 VDC, (Note 4)) Parameter Conditions LM139A Min Typ Saturation Voltage VIN(−)=1 VDC, VIN(+) = 0, LM239A, LM339A Max Min Typ Max LM139 Min Typ Units Max 700 700 700 mVDC 1.0 1.0 1.0 µADC 36 36 36 VDC ISINK ≤ 4 mA Output Leakage Current VIN(+) = 1 VDC, VIN(−) = 0, VO = 30 VDC, (LM3302, VO = 28 VDC) Keep all VIN’s ≥ 0 VDC (or V−, Differential Input Voltage if used), (Note 8) Electrical Characteristics (V+ = 5.0 VDC, (Note 4)) Parameter Conditions LM239, LM339 Min Typ Max LM2901 Min Typ LM3302 Max Min Typ Units Max Input Offset Voltage (Note 9) 9.0 9 15 40 Input Offset Current IIN(+)−IIN(−), VCM = 0V 150 50 200 300 mVDC nADC Input Bias Current IIN(+) or IIN(−) with Output in 400 200 500 1000 nADC V+−2.0 VDC 700 700 mVDC 1.0 1.0 1.0 µADC 36 36 28 VDC Linear Range, VCM = 0V (Note 5) Input Common-Mode V+ = 30 VDC (LM3302, V+ = 28 VDC) Voltage Range (Note 6) Saturation Voltage VIN(−) = 1 VDC, VIN(+) = 0, V+−2.0 700 V+−2.0 0 400 0 ISINK ≤ 4 mA Output Leakage Current VIN(+) = 1 VDC, VIN(−) = 0, VO = 30 VDC, (LM3302, V O = 28 VDC) Differential Input Voltage Keep all VIN’s ≥ 0 VDC (or V−, if used), (Note 8) Note 1: For operating at high temperatures, the LM339/LM339A, LM2901, LM3302 must be derated based on a 125˚C maximum junction temperature and a thermal resistance of 95˚C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM239 and LM139 must be derated based on a 150˚C maximum junction temperature. The low bias dissipation and the “ON-OFF” characteristic of the outputs keeps the chip dissipation very small (PD≤100 mW), provided the output transistors are allowed to saturate. Note 2: Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output current is approximately 20 mA independent of the magnitude of V+. Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3 VDC (at 25˚)C. Note 4: These specifications are limited to −55˚C ≤ TA ≤ +125˚C, for the LM139/LM139A. With the LM239/LM239A, all temperature specifications are limited to −25˚C ≤ TA ≤ +85˚C, the LM339/LM339A temperature specifications are limited to 0˚C ≤ TA ≤ +70˚C, and the LM2901, LM3302 temperature range is −40˚C ≤ TA ≤ +85˚C. Note 5: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the reference or input lines. Note 6: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is V+ −1.5V at 25˚C, but either or both inputs can go to +30 VDC without damage (25V for LM3302), independent of the magnitude of V+. Note 7: The response time specified is a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance characteristics section. Note 8: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than −0.3 VDC (or 0.3 VDCbelow the magnitude of the negative power supply, if used) (at 25˚C). Note 9: At output switch point, VO.1.4 VDC, RS = 0Ω with V+ from 5 VDC to 30 VDC; and over the full input common-mode range (0 VDC to V+ −1.5 VDC), at 25˚C. For LM3302, V+ from 5 VDC to 28 VDC. Note 10: Refer to RETS139AX for LM139A military specifications and to RETS139X for LM139 military specifications. www.national.com 4 LM139/LM239/LM339, LM139A/LM239A/LM339A, LM3302 Supply Current Input Current 00570634 00570635 Response Time for Various Input Overdrives — Negative Transition Output Saturation Voltage 00570637 00570636 Response Time for Various Input Overdrives — Positive Transition 00570638 5 www.national.com LM139/LM239/LM339/LM2901/LM3302 Typical Performance Characteristics LM139/LM239/LM339/LM2901/LM3302 Typical Performance Characteristics LM2901 Supply Current Input Current 00570640 00570639 Response Time for Various Input Overdrives — Negative Transition Output Saturation Voltage 00570642 00570641 Response Time for Various Input Overdrives — Positive Transition 00570643 www.national.com 6 Driving CMOS The LM139 series are high gain, wide bandwidth devices which, like most comparators, can easily oscillate if the output lead is inadvertently allowed to capacitively couple to the inputs via stray capacitance. This shows up only during the output voltage transition intervals as the comparator changes states. Power supply bypassing is not required to solve this problem. Standard PC board layout is helpful as it reduces stray input-output coupling. Reducing this input resistors to < 10 kΩ reduces the feedback signal levels and finally, adding even a small amount (1 to 10 mV) of positive feedback (hysteresis) causes such a rapid transition that oscillations due to stray feedback are not possible. Simply socketing the IC and attaching resistors to the pins will cause input-output oscillations during the small transition intervals unless hysteresis is used. If the input signal is a pulse waveform, with relatively fast rise and fall times, hysteresis is not required. All pins of any unused comparators should be tied to the negative supply. The bias network of the LM139 series establishes a drain current which is independent of the magnitude of the power supply voltage over the range of from 2 VDC to 30 VDC. It is usually unnecessary to use a bypass capacitor across the power supply line. The differential input voltage may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages from going negative more than −0.3 VDC (at 25˚C). An input clamp diode can be used as shown in the applications section. The output of the LM139 series is the uncommitted collector of a grounded-emitter NPN output transistor. Many collectors can be tied together to provide an output OR’ing function. An output pull-up resistor can be connected to any available power supply voltage within the permitted supply voltage range and there is no restriction on this voltage due to the magnitude of the voltage which is applied to the V+ terminal of the LM139A package. The output can also be used as a simple SPST switch to ground (when a pull-up resistor is not used). The amount of current which the output device can sink is limited by the drive available (which is independent of V+) and the β of this device. When the maximum current limit is reached (approximately 16 mA), the output transistor will come out of saturation and the output voltage will rise very rapidly. The output saturation voltage is limited by the approximately 60Ω RSAT of the output transistor. The low offset voltage of the output transistor (1 mV) allows the output to clamp essentially to ground level for small load currents. Typical Applications LM139/LM239/LM339/LM2901/LM3302 Application Hints 00570604 Driving TTL 00570605 AND Gate 00570608 OR Gate (V+ = 5.0 VDC) Basic Comparator 00570603 00570609 7 www.national.com LM139/LM239/LM339/LM2901/LM3302 Typical Applications (V+= 15 VDC) One-Shot Multivibrator 00570610 Bi-Stable Multivibrator 00570611 www.national.com 8 LM139/LM239/LM339/LM2901/LM3302 Typical Applications (V+= 15 VDC) (Continued) One-Shot Multivibrator with Input Lock Out 00570612 Pulse Generator 00570617 9 www.national.com LM139/LM239/LM339/LM2901/LM3302 Typical Applications (V+= 15 ORing the Outputs VDC) (Continued) Large Fan-In AND Gate 00570613 00570615 www.national.com 10 LM139/LM239/LM339/LM2901/LM3302 Typical Applications (V+= 15 VDC) (Continued) Time Delay Generator 00570614 Non-Inverting Comparator with Hysteresis Inverting Comparator with Hysteresis 00570618 00570619 11 www.national.com LM139/LM239/LM339/LM2901/LM3302 Typical Applications (V+= 15 Comparing Input Voltages of Opposite Polarity VDC) (Continued) Squarewave Oscillator 00570620 Output Strobing 00570616 Basic Comparator 00570622 * Or open-collector logic gate without pull-up resistor Crystal Controlled Oscillator 00570621 Limit Comparator 00570625 00570624 www.national.com 12 700 Hz ≤ fO ≤ 100 kHz V+ = +30 VDC 250 mVDC ≤ VC ≤ +50 VDC Typical Applications (V+= 15 VDC) (Continued) Two-Decade High-Frequency VCO 00570623 LM139/LM239/LM339/LM2901/LM3302 13 www.national.com LM139/LM239/LM339/LM2901/LM3302 Typical Applications (V+= 15 Zero Crossing Detector (Single Power Supply) VDC) (Continued) Transducer Amplifier 00570630 Split-Supply Applications (V+ = +15 VDC and V− = −15 VDC) 00570628 MOS Clock Driver 00570631 www.national.com 14 Comparator With a Negative Reference and V− = −15 VDC) (Continued) Zero Crossing Detector 00570633 Schematic Diagram 00570632 00570601 15 www.national.com LM139/LM239/LM339/LM2901/LM3302 Split-Supply Applications (V+ = +15 VDC LM139/LM239/LM339/LM2901/LM3302 Connection Diagrams Dual-In-Line Package 00570602 Order Number LM139J, LM139J/883 (Note 11), LM139AJ, LM139AJ/883 (Note 12), LM239J, LM239AJ, LM339J See NS Package Number J14A Order Number LM339AM, LM339AMX, LM339M, LM339MX or LM2901M See NS Package Number M14A Order Number LM339N, LM339AN, LM2901N or LM3302N See NS Package Number N14A 00570627 Order Number LM139AW/883 or LM139W/883 (Note 11) See NS Package Number W14B, LM139AWGRQMLV (Note 13) See NS Package Number WG14A Note 11: Available per JM38510/11201 Note 12: Available per SMD# 5962-8873901 Note 13: See STD Mil Dwg 5962R96738 for Radiation Tolerant Device www.national.com 16 LM139/LM239/LM339/LM2901/LM3302 Physical Dimensions inches (millimeters) unless otherwise noted Ceramic Dual-In-Line Package (J) Order Number LM139J, LM139J/883, LM139AJ, LM139AJ/883, LM239J, LM239AJ, LM339J NS Package Number J14A S.O. Package (M) Order Number LM339AM, LM339AMX, LM339M, LM339MX, LM2901M or LM2901MX NS Package Number M14A 17 www.national.com LM139/LM239/LM339/LM2901/LM3302 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Molded Dual-In-Line Package (N) Order Number LM339N, LM339AN, LM2901N or LM3302N NS Package Number N14A Order Number LM139AW/883, LM139W/883 NS Package Number W14B www.national.com 18 inches (millimeters) unless otherwise noted (Continued) Order Number LM139AWG/883, LM139WG/883 NS Package Number WG14A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM139/LM239/LM339/LM2901/LM3302 Low Power Low Offset Voltage Quad Comparators Physical Dimensions IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated