HITTITE HMC699LP5

HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Typical Applications
Features
The HMC699LP5(E) is ideal for:
Ultra Low SSB Phase Noise Floor:
-153 dBc/Hz @ 10 kHz offset @ 100 MHz
Reference Frequency.
• Satellite Communication Systems
• Point-to-Point Radios
Programmable Divider (N= 56 - 519) Operating
up to 7 GHz
• Military Applications
• Sonet Clock Generation
Open Collector Output Buffer Amplifiers for
Interfacing w/ Op-Amp Based Loop Filter
Reversible Polarity PFD w/ Lock Detect Output
32 Lead 5x5mm SMT Package: 25mm 2
PLL - INTEGER-N SYNTHESIZER - SMT
11
Functional Diagram
General Description
The HMC699LP5(E) is a frequency synthesizer with
a wideband reversible polarity digital PFD and lock
detect output. The divider operates unconditionally
from 160 - 7000 MHz with a continuous integer
division ratio of 56 to 519. The HMC699LP5(E) high
frequency operation along with ultra low phase noise
floor make possible synthesizers with wide loop
bandwidth and low N resulting in fast settling and
very low phase noise. When used in conjunction with
a differential loop filter, the HMC699LP5(E) can be
used to phase lock a VCO to a reference oscillator.
Electrical Specifi cations, TA = +25° C, Vcc = Vcc1 = Vcc2 = Vcc3 = Vcc_pd = 5V
Conditions
Min.
Maximum Ref. Input Frequency
Parameter
Sine or Square Wave Input [1]
1300
Minimum Ref. Input Frequency
Square Wave Input [2]
Reference Input Power Range
100 MHz Frequency
Maximum VCO Input Frequency
Minimum VCO Input Frequency
VCO Input Power Range
SSB Phase Noise
Max.
Units
10
MHz
+5
dBm
MHz
-5
7000
MHz
Sine Wave Input
100 MHz Input Frequency
PFD Output Voltage
PFD Gain
Typ.
-10
160
MHz
+5
dBm
2000
mV, Pk - Pk
Gain = Vpp / 2π Rad.
0.32
V/Rad.
@ 10 kHz Offset @ 100 MHz Square Wave Ref. Input
Pin= 0 dBm
-153
dBc/Hz
345
mA
Total Supply Current
[1] Maximum frequencies may be limited by available counter division ratio.
[2] Square wave input achieves best phase noise at lower ref. frequency (see sine & square wave comparison plots)
11 - 24
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Phase Noise Floor [1][2][3]
Ref = Sine Wave, Vcc = 4.75V
Phase Noise Floor [1][2][3]
Ref = Square Wave, Vcc = 4.75V
-100
-110
-10 dBm
-5 dBm
0 dBm
+5 dBm
-120
SSB PHASE NOISE (dBc/Hz)
-130
-140
-150
-160
-170
-180
2
10
-110
-120
-130
-140
-150
-160
-170
3
4
10
10
-180
2
10
5
10
OFFSET FREQUENCY (Hz)
-110
-10 dBm
-5 dBm
0 dBm
+5 dBm
-120
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
5
10
11
-100
-130
-140
-150
-160
-170
-110
-120
-10 dBm
-5 dBm
0 dBm
+5 dBm
-130
-140
-150
-160
-170
3
10
4
10
-180
2
10
5
10
OFFSET FREQUENCY (Hz)
3
10
4
10
5
10
OFFSET FREQUENCY (Hz)
Phase Noise Floor [1][2][3]
Ref = Sine Wave, Vcc = 5.25V
Phase Noise Floor [1][2][3]
Ref = Square Wave, Vcc = 5.25V
-100
-100
-110
-10 dBm
-5 dBm
0 dBm
+5 dBm
-120
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
4
10
Phase Noise Floor [1][2][3]
Ref = Square Wave, Vcc = 5V
-100
-130
-140
-150
-160
-170
-180
2
10
3
10
OFFSET FREQUENCY (Hz)
Phase Noise Floor [1][2][3]
Ref = Sine Wave, Vcc = 5V
-180
2
10
-10 dBm
-5 dBm
0 dBm
+5 dBm
-110
-10 dBm
-5 dBm
0 dBm
+5 dBm
-120
-130
-140
-150
-160
-170
3
10
4
10
5
10
OFFSET FREQUENCY (Hz)
-180
2
10
3
10
4
10
PLL - INTEGER-N SYNTHESIZER - SMT
SSB PHASE NOISE (dBc/Hz)
-100
5
10
OFFSET FREQUENCY (Hz)
[1] Phase Noise Floor vs Offset Frequency with varying Ref Power Level
[2] Fin= 7000 MHz @ 0 dBm, Ref Frequency = 100 MHz, N = 70
[3] Phase Noise Floor remains constant beyond 100 kHz offset frequency
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 25
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Phase Noise Floor [1][2][3]
Ref = Sine Wave @ 5 dBm, Vcc = 5V
-100
-100
-110
-110
-120
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
Phase Noise Floor [1][2][3]
Ref = Square Wave @ 5 dBm, Vcc = 5V
+25 C
+85 C
-40 C
-130
-140
-150
-160
-170
-180
2
10
-130
-140
-150
-160
-170
3
4
10
-180
2
10
5
10
10
3
10
OFFSET FREQUENCY (Hz)
11
4
5
10
10
OFFSET FREQUENCY (Hz)
Phase Noise Floor vs Offset Frequency
with varying Fin @ 0 dbm, Ref = 100 MHz
Square Wave @ 5 dBm, Vcc = 5V [3]
Absolute Maximum Ratings
RF Input (Vcc = +5V)
+10 dBm
Supply Voltage (Vcc)
+5.5V
Logic Inputs
-0.5V to (0.5V + Vcc)
Junction Temperature (Tc)
135 °C
Continuous Pdiss (T = 85 °C)
(derate 87 mW/° C above 85 °C)
4.3 W
-140
Thermal Resistance
(Junction to ground paddle)
11.60 °C/W
-150
Storage Temperature
-65 to +150 °C
-160
Operating Temperature
-40 to +85 °C
-100
SSB PHASE NOISE (dBc/Hz)
PLL - INTEGER-N SYNTHESIZER - SMT
+25 C
+85 C
-40 C
-120
-110
1600 MHz
7000 MHz
-120
-130
-170
-180
2
10
3
4
10
5
10
10
OFFSET FREQUENCY (Hz)
Typical DC Characteristics @ Vcc = +5V
Typical Supply Current vs. Vcc
+25C
Symbol
Characteristics
Icc
Power Supply
Current
310
Voh
Output High
Voltage, (NU, ND)
5
5
5
V
Vol
Output Low
Voltage, (NU, ND)
2.9
3.0
3.1
V
Vcc (Vdc)
Units
Min.
Typ.
345
Max.
380
mA
Icc (mA)
4.75
318
5.00
345
5.25
369
Note: HMC669LP5(E) will work over full voltage range above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
[1] Phase Noise Floor vs Offset Frequency over temperature
[2] Fin= 7000 MHz @ 0 dBm, Ref Frequency = 100 MHz, N = 70
[3] Phase Noise Floor remains constant beyond 100 kHz offset frequency
11 - 26
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC699LP5
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC699LP5(E)
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H699
XXXX
[2]
H699
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - INTEGER-N SYNTHESIZER - SMT
11
11 - 27
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Pin Description
Pin Number
Function
Description
Interface Schematic
Pulsed output.
1
LD
Average “LOW” = UNLOCKED.
Average “HIGH” = LOCKED
PFD INVERT function
11
CMOS compatible input control bit
2
INV
PLL - INTEGER-N SYNTHESIZER - SMT
Logic “LOW” = NORMAL
11 - 28
Logic “HIGH” = INVERT
4, 5, 18, 25
Vcc1, Vcc3,
Vcc2, Vcc_pd
Supply Voltage 5V ±0.25V
9 - 14
N0 - N5
CMOS compatible control input bit 0 (LSB) - 5
15
FIN
(These pins are AC coupled and must be DC Blocked externally.)
Frequency Input
16
NFIN
Frequency Input Complement
CMOS compatible
22, 23
S1, S0
Control Input
bit 0 (LSB) -1
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Pin Description (Continued)
Pin Number
Function
28
REF
Description
Interface Schematic
Reference Input
Reference Input Complement
(These pins are AC coupled and must be DC Blocked externally.)
27
NREF
30
ND
Down Output
31
NU
Up Output
3, 6 - 8, 17,
19, 20, 24,
26, 29, 32
N/C
No Connection. These pins may be connected to RF/DC ground.
Performance will not be affected.
Ground
Paddle
GND
Package bottom has an exposed ground paddle that must be connected to RF/DC ground
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - INTEGER-N SYNTHESIZER - SMT
11
11 - 29
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
HMC699LP5(E) Programming Truth Table
Division
Ratio n
PLL - INTEGER-N SYNTHESIZER - SMT
11
11 - 30
N Counter
N Counter
Decimal Set
Swallow
S Counter
Swallow S
Decimal Set
(LSB)
N0
N1
N2
N3
N4
N5
(LSB)
S0
S1
S2
56
7
6
0
0
0
1
1
0
0
0
0
0
0
57
7
6
1
1
0
1
1
0
0
0
1
0
0
58
7
6
2
2
0
1
1
0
0
0
0
1
0
59
7
6
3
3
0
1
1
0
0
0
1
1
0
60
7
6
4
4
0
1
1
0
0
0
0
0
1
61
7
6
5
5
0
1
1
0
0
0
0
0
1
62
7
6
6
6
0
1
1
0
0
0
0
1
1
63
7
6
7
7
0
1
1
0
0
0
1
1
1
64
8
7
0
0
1
1
1
0
0
0
0
0
0
65
8
7
1
1
1
1
1
0
0
0
1
0
0
66
8
7
2
2
1
1
1
0
0
0
0
1
0
67
.
.
.
8
.
.
.
7
.
.
.
3
.
.
.
3
.
.
.
1
.
.
.
1
.
.
.
1
.
.
.
0
.
.
.
0
.
.
.
0
.
.
.
1
.
.
.
1
.
.
.
0
.
.
.
512
64
63
0
0
1
1
1
1
1
1
0
0
0
513
64
63
1
1
1
1
1
1
1
1
1
0
0
514
64
63
2
2
1
1
1
1
1
1
0
1
0
515
64
63
3
3
1
1
1
1
1
1
1
1
0
516
64
63
4
4
1
1
1
1
1
1
0
0
1
517
64
63
5
5
1
1
1
1
1
1
1
0
1
518
64
63
6
6
1
1
1
1
1
1
0
1
1
519
64
63
7
7
1
1
1
1
1
1
1
1
1
N = INT (n/P)
S = MOD (n/P)
Where: n = Desired division ratio
P = Prescaler value = 8
N = Counter N value (counter decimal set is N - 1)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
HMC699LP5(E) Programming Truth Table, Non-Continuous Division Ratios
N Counter
N Counter
Decimal Set
Swallow
S Counter
Swallow S
Decimal Set
(LSB)
N0
N1
N2
N3
N4
N5
(LSB)
S0
S1
S2
16
2
1
0
0
1
0
0
0
0
0
0
0
0
17
2
1
1
1
1
0
0
0
0
0
1
0
0
18
2
1
2
2
1
0
0
0
0
0
0
1
0
24
3
2
0
0
0
1
0
0
0
0
0
0
0
25
3
2
1
1
0
1
0
0
0
0
1
0
0
26
3
2
2
2
0
1
0
0
0
0
0
1
0
27
3
2
3
3
0
1
0
0
0
0
1
1
0
32
4
3
0
0
1
1
0
0
0
0
0
0
0
33
4
3
1
1
1
1
0
0
0
0
1
0
0
34
4
3
2
2
1
1
0
0
0
0
0
1
0
35
4
3
3
3
1
1
0
0
0
0
1
1
0
36
4
3
4
4
1
1
0
0
0
0
0
0
1
40
5
4
0
0
0
0
1
0
0
0
0
0
0
41
5
4
1
1
0
0
1
0
0
0
1
0
0
42
5
4
2
2
0
0
1
0
0
0
0
1
0
43
5
4
3
3
0
0
1
0
0
0
1
1
0
44
5
4
4
4
0
0
1
0
0
0
0
0
1
45
5
4
5
5
0
0
1
0
0
0
1
0
1
48
6
5
0
0
1
0
1
0
0
0
0
0
0
49
6
5
1
1
1
0
1
0
0
0
1
0
0
50
6
5
2
2
1
0
1
0
0
0
0
1
0
51
6
5
3
3
1
0
1
0
0
0
1
1
0
52
6
5
4
4
1
0
1
0
0
0
0
0
1
53
6
5
5
5
1
0
1
0
0
0
1
0
1
54
6
5
6
6
1
0
1
0
0
0
0
1
1
N = INT (n/P)
S = MOD (n/P)
Where: n = Desired division ratio
P = Prescaler value = 8
N = Counter N value (counter decimal set is N - 1)
11
PLL - INTEGER-N SYNTHESIZER - SMT
Division
Ratio n
* Choose values of R2 & R4 between 4.3 and 20 Ohms for best noise performance.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 31
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Evaluation PCB Circuit
PLL - INTEGER-N SYNTHESIZER - SMT
11
11 - 32
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Evaluation PCB
The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50
ohm impedance while the package backside ground paddle should be connected directly to the ground plane similar
to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The
evaluation circuit board shown is available from Hittite upon request.
List of Materials for
Evaluation PCB 116108
[1]
Item
Description
J1 - J4
PC Mount SMA RF Connector
J5 - J6
2mm DC Header
C1 - C5, C8 - C10
1000 pF Capacitor, 0402 Pkg
C6 - C7
100 pF Capacitor, 0402 Pkg
C15
1000 pF Capacitor, 0603 Pkg
C16
4.7 μF Tantalum Capacitor Case A
D
LED Green, 0603 Pkg
R1
10k Ohm, Resistor, Array
R8, R9, R10
10k Ohm, Resistor, 0402 Pkg.
R11
1k Ohm, Resistor, 0402 Pkg.
R12
100 Ohm, Resistor, 0402 Pkg.
U1
HMC699LP5(E) Synthesizer
PCB [2]
116106 Eval Board
Evaluation PCB Truth Table
(see Programming Truth Table)
Note: 0 = Jumper Installed.
1 = Jumper Not Installed.
Note: The evaluation PCB for the HMC699LP5 contains
10K Ohm pull up resistors for each of the control inputs N0
through N5 and S0 through S2. Programming the 489 distinct division ratios consists of installing or removing jumpers
N0 through N5 and S0, S1.
PLL - INTEGER-N SYNTHESIZER - SMT
11
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 33
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Typical PLL Application Circuit using HMC699LP5
PLL application shown for a 13 GHz Fout. Contact HMC to discuss your specific application.
PLL - INTEGER-N SYNTHESIZER - SMT
11
11 - 34
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER
(N = 56 - 519)
Typical Application
Showing Spurious Performance
Typical Application
13 GHz Measured Phase Noise [1]
SSB PHASE NOISE (dBc/Hz)
-100
-110
-120
-130
MEASURED
CALCULATED
-140
-150
-160
-170
3
4
10
10
5
10
6
10
7
10
OFFSET FREQUENCY (Hz)
[1] Phase Noise Floor remains constant beyond 100 kHz offset
frequency. Measured phase noise using Agilent 5500 with 2 unit
measurement technique and corresponding calculated phase noise
floor.
CMOS/TTL Input Characteristics
Maximum Input Logic “0” Voltage (VIL MAXIMUM) = 1.1V @ 1 μA.
Minimum Input Logic “1” Voltage (VIH MINIMUM) = 1.8V @ 50 μA.
Input IV characteristics for the logic inputs (N0 - N5 and S0 - S2) are shown below:
0.4
V
V
IL MAX
IH MIN
Input Current (mA)
0.3
0.2
0.1
0
-0.1
0
1
2
3
4
5
Input Voltage (V)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - INTEGER-N SYNTHESIZER - SMT
-180
2
10
11 - 35