HMC736LP4 / 736LP4E v00.1008 MMIC VCO w/ HALF FREQUENCY OUTPUT 14.5 - 15.0 GHz Typical Applications Features The HMC736LP4(E) is ideal for: Dual Output: Fo = 14.5 - 15.0 GHz Fo/2 = 7.25 - 7.5 GHz • Point to Point/Multipoint Radio • Test Equipment & Industrial Controls Pout: +9 dBm Phase Noise: -105 dBc/Hz @ 100 kHz • SATCOM • Military End-Use No External Resonator Needed 24 Lead 4x4mm SMT Package: 16mm2 Functional Diagram The HMC736LP4(E) is a GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCO. The HMC736LP4(E) integrates a resonator, negative resistance device, varactor diode and feature half frequency output. The VCO’s phase noise performance is excellent over temperature, shock, and process due to the oscillator’s monolithic structure. Power output is +9 dBm typical from a +4.2V supply voltage. The voltage controlled oscillator is packaged in a leadless QFN 4x4 mm surface mount package, and requires no external matching components. 12 VCOS WITH FO/2 OUTPUT - SMT General Description Electrical Specifi cations, TA = +25° C, Vcc = +4.2V Parameter Frequency Range Min. Fo Fo/2 RFOUT RFOUT/2 Power Output 6 -8 SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RFOUT Tune Voltage Typ. 9 -3 Vtune Supply Current 1 120 150 Output Return Loss Units GHz GHz 13 2 -105 Tune Port Leakage Current (Vtune= 13V) dBm dBm dBc/Hz 13 V 180 mA 10 µA 2.5 dB -45 -42 dBc dBc Pulling (into a 2.0:1 VSWR) 12 MHz pp Pushing @ Vtune= 5V 24 MHz/V Frequency Drift Rate 1.2 MHz/°C Harmonics/Subharmonics 12 - 220 Max. 14.5 - 15.0 7.25 - 7.5 1/2 3/2 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC736LP4 / 736LP4E v00.1008 MMIC VCO w/ HALF FREQUENCY OUTPUT 14.5 - 15.0 GHz Frequency vs. Tuning Voltage, T= 25°C 17 17 16 16 FREQUENCY (GHz) 15 14 +25 C +85 C -40 C 13 15 14 Vcc = 4.0V Vcc = 4.2V Vcc = 4.4V 13 12 12 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 TUNING VOLTAGE (VOLTS) Sensitivity vs. Tuning Voltage, Vcc = +4.2V 6 7 8 9 10 11 12 13 12 14 500 OUTPUT POWER (dBm) SENSITIVITY (MHz/VOLT) 5 Output Power vs. Tuning Voltage, Vcc = +4.2V 600 +25 C +85 C -40 C 400 300 200 100 0 12 10 8 +25 C +85 C -40 C 6 4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 TUNING VOLTAGE (VOLTS) -70 -50 SSB PHASE NOISE (dBc/Hz) -30 -80 10kHz offset 100kHz offset -100 -110 -120 0 1 2 3 4 5 6 7 8 9 TUNING VOLTAGE (VOLTS) 2 3 4 5 6 7 8 9 10 11 12 13 SSB Phase Noise @ Vtune = +5V -60 -90 1 TUNING VOLTAGE (VOLTS) SSB Phase Noise vs. Tuning Voltage SSB PHASE NOISE(dBc/Hz) 4 TUNING VOLTAGE (VOLTS) 10 11 12 13 +25 C +85 C -40 C -70 -90 -110 VCOS WITH FO/2 OUTPUT - SMT FREQUENCY (GHz) Frequency vs. Tuning Voltage, Vcc = +4.2V -130 -150 3 10 4 10 5 6 10 10 OFFSET FREQUENCY (Hz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 10 12 - 221 HMC736LP4 / 736LP4E v00.1008 MMIC VCO w/ HALF FREQUENCY OUTPUT 14.5 - 15.0 GHz RFOUT/2 Output Power vs. Tuning Voltage, Vcc = +4.2V 9 0 8.5 -1 OUTPUT POWER (dBm) FREQUENCY (GHz) RFOUT/2 Frequency vs. Tuning Voltage, Vcc = +4.2V 8 7.5 7 +25 C +85 C -40 C 6.5 -2 -3 -4 +25 C +85 C -40 C -5 6 -6 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 TUNING VOLTAGE (VOLTS) VCOS WITH FO/2 OUTPUT - SMT 12 12 - 222 Absolute Maximum Ratings 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (VOLTS) Typical Supply Current vs. Vcc Vcc +5.5V Vtune 0 to 15V Vcc (V) 4.0 Icc (mA) 140 Junction Temperature 135 °C 4.2 150 Storage Temperature -65 to +150 °C 4.4 160 Operating Temperature -40 to +85 °C Note: VCO will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Package Information Part Number Package Body Material Lead Finish MSL Rating HMC736LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC736LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H736 XXXX [2] H736 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC736LP4 / 736LP4E v00.1008 MMIC VCO w/ HALF FREQUENCY OUTPUT 14.5 - 15.0 GHz Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 12 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Application Circuit For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com VCOS WITH FO/2 OUTPUT - SMT 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. 12 - 223 HMC736LP4 / 736LP4E v00.1008 MMIC VCO w/ HALF FREQUENCY OUTPUT 14.5 - 15.0 GHz Pin Descriptions Function Description 1 - 9, 11 - 14, 18, 19, 21, 23, 24 Pin Number N/C No Connection. These pins may be connected to RF/ DC ground. Performance will not be affected. 10 RFOUT/2 Half frequency output (AC coupled). Requires external AC coupling capacitor. 16 RFOUT RF output (AC coupled). 20 Vcc Supply Voltage, +4.2V 22 VTUNE Control voltage and modulation input. Modulation bandwidth dependent on drive source impedance. See “Determining the FM Bandwidth of a Wideband Varactor Tuned VCO” application note. 15, 17, Paddle GND Package bottom has an exposed metal paddle that must be connected to RF/DC ground. VCOS WITH FO/2 OUTPUT - SMT 12 12 - 224 Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC736LP4 / 736LP4E v00.1008 MMIC VCO w/ HALF FREQUENCY OUTPUT 14.5 - 15.0 GHz Evaluation PCB List of Materials for Evaluation PCB 123987 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 2 mm DC Header C1, C2 100 pF Capacitor, 0402 Pkg. C3 4.7 μF Tantalum Capacitor U1 HMC736LP4(E) VCO PCB [2] 124532 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com VCOS WITH FO/2 OUTPUT - SMT 12 12 - 225