HITTITE HMC391LP4

HMC391LP4 / 391LP4E
v03.0209
MMIC VCO w/ BUFFER
AMPLIFIER, 3.9 - 4.45 GHz
Typical Applications
Features
Low noise MMIC VCO w/Buffer Amplifier for:
Pout: +5.0 dBm
• VSAT & Microwave Radio
Phase Noise: -106 dBc/Hz @100 KHz
• Radio Altimetry
No External Resonator Needed
• Test Equipment & Industrial Controls
Single Supply: +3V @ 30 mA
• Military
24 Lead 4x4mm QFN Package: 9 mm2
Functional Diagram
General Description
The HMC391LP4 & HMC391LP4E are GaAs InGaP
Heterojunction Bipolar Transistor (HBT) MMIC VCOs
with integrated resonators, negative resistance
devices, varactor diodes, and buffer amplifiers.
Covering 3.9 to 4.45 GHz, the VCO’s phase noise
performance is excellent over temperature, shock,
vibration and process due to the oscillator’s monolithic
structure. Power output is 5.0 dBm typical from a
single supply of +3V @ 30 mA. The voltage controlled
oscillator is packaged in a low cost leadless QFN 4 x 4
mm surface mount package.
VCOS - SMT
12
Electrical Specifi cations, TA = +25° C, Vcc = +3V
Parameter
Min.
Frequency Range
Power Output
1.5
SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RF Output
Tune Voltage (Vtune)
Supply Current (Icc) (Vcc = +3V)
Typ.
12 - 30
Units
GHz
5.0
dBm
-106
dBc/Hz
0
30
Tune Port Leakage Current
Output Return Loss
Max.
3.9 - 4.45
10
V
40
mA
10
μA
7
dB
Harmonics
2nd
3rd
-9
-23
dBc
dBc
Pulling (into a 2.0:1 VSWR)
8.0
MHz pp
Pushing @ Vtune= +5V
16
MHz/V
Frequency Drift Rate
0.5
MHz/°C
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC391LP4 / 391LP4E
v03.0209
MMIC VCO w/ BUFFER
AMPLIFIER, 3.9 - 4.45 GHz
Frequency vs. Tuning Voltage, Vcc= +3V
4.7
4.7
4.6
4.6
OUTPUT FREQUENCY (GHz)
4.5
4.4
4.3
4.2
4.1
4
Vcc=2.75V
Vcc=3.0V
Vcc=3.25V
3.9
3.8
3.7
4.5
4.4
4.3
4.2
4.1
4
+25 C
+85 C
-40 C
3.9
3.8
3.7
3.6
3.6
0
1
2
3
4
5
6
7
8
9
10
0
1
2
TUNING VOLTAGE (VOLTS)
5
6
7
8
9
10
12
8
7
+25 C
+85 C
-40 C
6
5
4
3
+25 C
+85 C
-40 C
2
1
0
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
TUNING VOLTAGE (VOLTS)
-65
SSB PHASE NOISE (dBc/Hz)
-70
-75
-80
-85
10 KHz Offset
-95
100 KHz Offset
-100
-105
-110
-115
-120
0
1
2
3
4
5
6
7
TUNING VOLTAGE (VOLTS)
5
6
7
8
9
10
Typical SSB Phase Noise @ Vtune= +5V
-60
-90
4
TUNING VOLTAGE (VOLTS)
Phase Noise vs. Tuning Voltage
SSB PHASE NOISE (dBc/Hz)
4
Output Power vs.
Tuning Voltage, Vcc= +3V
OUTPUT POWER (dBm)
SENSITIVITY (MHz/VOLT)
Sensitivity vs. Tuning Voltage, Vcc= +3V
300
280
260
240
220
200
180
160
140
120
100
80
60
40
20
3
TUNING VOLTAGE (VOLTS)
VCOS - SMT
OUTPUT FREQUENCY (GHz)
Frequency vs. Tuning Voltage, T= 25°C
8
9
10
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
-150
3
10
+25 C
+85 C
-40 C
4
10
5
10
6
10
7
10
OFFSET FREQUENCY (Hz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
12 - 31
HMC391LP4 / 391LP4E
v03.0209
MMIC VCO w/ BUFFER
AMPLIFIER, 3.9 - 4.45 GHz
Absolute Maximum Ratings
Typical Supply Current vs. Vcc
Vcc
+3.5 Vdc
Vcc (V)
Icc (mA)
Vtune
0 to +11V
2.75
22
Channel Temperature
135 °C
3.0
30
3.25
39
Continuous Pdiss (T = 85°C)
(derate 3 mW/°C above 85°C)
150 mW
Thermal Resistance
(junction to ground paddle)
333 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Note: VCO will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
VCOS - SMT
12
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC391LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC391LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H391
XXXX
[2]
H391
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
12 - 32
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC391LP4 / 391LP4E
v03.0209
MMIC VCO w/ BUFFER
AMPLIFIER, 3.9 - 4.45 GHz
Pin Descriptions
Function
Description
Interface Schematic
1- 14, 17 - 19,
21, 23, 24
N/C
No Connection
15
GND
This pin must be connected to RF & DC ground. Package bottom
has an exposed metal paddle that must be RF & DC grounded.
16
RFOUT
RF output (AC coupled)
20
Vcc
Supply Voltage Vcc= 3V
22
VTUNE
Control Voltage Input. Modulation port bandwidth
dependent on drive source impedance.
12
VCOS - SMT
Pin Number
Evaluation PCB
List of Materials for Evaluation PCB 105706 [1]
Item
Description
J1 - J2
PCB Mount SMA RF Connector
J3 - J4
DC Pin
C1
4.7 μF Tantalum Capacitor
C2
10,000 pF Capacitor, 0603 Pkg.
U1
HMC391LP4 / HMC391LP4E VCO
PCB [2]
105667 Eval Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
12 - 33