HITTITE HMC807LP6CE_10

HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Features
Features
• RF Bandwidth: 12.4 GHz to 13.4 GHz
• 24-bit Step Size, Resolution 3 Hz typ
• Fractional or Integer Modes
• 225 MHz, 14-bit reference path input
• Ultra Low Phase Noise
12.9 GHz; 50 MHz Ref.
-95 / -98 dBc/Hz @ 10 kHz (Frac / Int)
-132 dBc/Hz @ 1 MHz (Open Loop)
• Direct FSK Modulation Mode
• Figure of Merit (FOM)
-221 / -226 dBc/Hz (Frac / Int)
• Cycle Slip Prevention
• Read / Write Serial Port, Chip ID
• 40 Lead 6x6mm SMT Package: 36mm2
Typical Applications
6
• VSAT Radio
• Military End-Use
• Point-to-Point / Multi-Point Radio
• Phased Array Applications
PLLS w/ INTEGRATED VCO - SMT
• Test Equipment & Industrial Control
Functional Diagram
[1] Please refer to the pin description table for details
6 - 44
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
General Description
The HMC807LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an
Integrated Voltage Controlled Oscillator (VCO). The input reference frequency range is 100 kHz to 220 MHz while the
advanced delta-sigma modulator design in the fractional synthesizer allows both ultra-fine step sizes and very low
spurious products. The highly integrated structure provides excellent phase noise performance over temperature,
shock and process. The HMC807LP6CE is packaged in a leadless QFN 6x6 mm surface mount package. The output
power is 8 dBm typical, making the HMC807LP6CE ideal for driving the LO port of many of Hittite’s Hi Linearity and
I/Q mixer products.
For theory of operation and register map refer to the “PLLs w/ Integrated VCO - Microwave VCOs” Operating Guide.
To view the Operating Guide, please visit www.hittite.com and choose HMC807LP6CE from the “Search by Part
Number” pull down menu.
Electrical Specifi cations, TA = +25° C; VCCVCO, VDDCP, VCCCP = +5V; AVCC, VCCPS
VDDPFD, AVDD, RVDD, DVDD, DVDDM, DVDDQ, VDDIO = +3.3V; AGND = DGND = 0V
Condition
Min.
Typ.
Max.
Units
RF Output Characteristics
VCO Output Frequency Range
12.4
12.9
13.4
GHz
VCO Output Power
4
8
10
dBm
VCO Tuning Voltage
2
13
V
VCO Tuning Sensitivity
V TUNE = +5V
190
MHz/V
5
MHz pp
6
MHz/V
Frequency Drift Rate
1.2
MHz/
°C
Sub Harmonic (1/2)
25
dBc
Harmonic (2nd)
18
dBc
Harmonic (3rd)
35
dBc
V TUNE = +5V
Fvco = 12.9 GHz
-110
dBc/Hz
Fref = 50 MHz Fvco = 12.9 GHz
Loop BW = 100 kHz
-95 / -98
dBc/Hz
-221 / -226
dBc/Hz
-65
dBc
104
us
Frequency Pulling (into a 2:1 VSWR)
Frequency Pushing
VCO SSB Phase Noise @ 100 kHz Offset (Open Loop)
Synthesizer In-Band
SSB Phase Noise @ 10 kHz Offset (Frac/Int)
V TUNE = +5V
Synthesizer Normalized In-Band
SSB Phase Noise Floor (Frac/Int)
Synthesizer Fractional Spurs [1]
Synthesizer Frequency Settling Time (100 MHz Step)
16-Bit Divider Range (Int)
16-Bit Divider Range (Frac)
From 13 GHz to 12.9 GHz
Loop BW = 100 kHz
N Divider Ratio 216+31
32
65567
N Divider Ratio 216 -1
36
65535
PLLS w/ INTEGRATED VCO - SMT
Parameter
6
REF Input Characteristics
Max Ref Input Frequency (3.3V)
200
Min Ref Input Frequency
Ref Input Sensitivity
AC Coupled
Max Ref Input
DC Coupled
0
Ref Input Capacitance
14-Bit Ref Divider Range
16383
225
MHz
100
200
kHz
500
700
mVpp
VDDIO
V
5
pF
1
[1] Actual spur level is dependent on loop parameters and will increase at division ratios closest to integer boundaries. Number listed is average
value.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6 - 45
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Electrical Specifi cations (Continued)
Parameter
Condition
Min.
Typ.
Max.
Units
Phase Detector
Max Phase Detector Frequency (Frac)
70
105
MHz
Max Phase Detector Frequency (Int)
140
160
MHz
Min Phase Detector Frequency
100
kHz
Charge Pump
Max Output Current
2
Min Output Current
Charge Pump Noise
Input referred 50 MHz Ref.
mA
500
μA
-145
dBc/Hz
Logic Inputs
PLLS w/ INTEGRATED VCO - SMT
6
6 - 46
VIH Input High Voltage
VDDIO-0.4
VDDIO
V
VIL Input Low Voltage
0
0.4
V
VOH Output High Voltage
VDDIO-0.4
VDDIO
V
VOL Output Low Voltage
0
0.4
Logic Outputs
Serial Port Max Clock
50
V
MHz
Power Supply Voltages
Analog 3.3V Supplies: AVCC, VDDPFD, AVDD, RVDD,
VCCPS
AVDD must equal DVDD
3
3.3
3.45
V
3
3.3
3.45
V
Logic I/O
1.8
3.3
5.5
V
VCCCP must equal VDDCP
4.75
5
5.25
V
Total Current Consumption (5V)
205
250
mA
Total Current Consumption (3.3V)
90
110
mA
1
10
μA
Digital Internal Supplies: DVDD, DVDDQ, DVDDM
Digital I/O Supplies: VDDIO
Analog 5V Supplies: VCCVCO, VDDCP, VCCCP
Power Supply Currents
CSP Disabled
Power Down Current [1]
Bias Reference Voltage
CSP Enabled
Measured with 10 GΩ meter
450
1.880
1.920
μA
1.960
[1] Refers only to the Synthesizer portion of the HMC807LP6CE
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
V
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
SSB Phase Noise vs. Frequency,
Integer Mode
SSB Phase Noise vs. Temperature
@ 12.9 GHz, Integer Mode
-60
-70
12.4 GHz
12.9 GHz
13.4 GHz
-80
PHASE NOISE (dBc/Hz)
PHASE NOISE (dBc/Hz)
-70
-90
-100
-110
-120
-130
Temp = 25C
Fref = 50MHz
Loop BW = 100kHz
-140
2
10
3
-90
-100
-110
-120
-130
Fref = 50MHz
Loop BW = 100kHz
-140
-150
10
+25 C
+85 C
-40 C
-80
10
4
10
5
10
6
10
-150
2
10
7
10
3
-60
-60
-70
-70
-80
-90
-100
-110
-120
Temp = 25C
Fref = 50MHz
Loop BW = 100kHz
-150
2
10
10
3
4
10
5
10
6
10
7
6
-120
Fref = 10MHz
Loop BW= 10kHz
-130
Fref = 50MHz
Loop BW=100kHz
10
3
10
4
10
5
10
6
10
7
OFFSET FREQUENCY (Hz)
Typical Reference Sensitivity
vs. Frequency, 3.3V [1]
20
13.2
10
SENSITIVITY (dBm)
FREQUENCY (GHz)
10
-110
13.3
13.1
CSP OFF
12.9
CSP ON
12.7
R = Max, +25C
R = Max, +85C
0
-10
R = 3, +25C
R = 3, +85C
-20
-30
-40
12.6
-10
6
-90
-150
2
10
7
Example of Cycle Slip Prevention Hop
from 13.2 to 12.7 GHz
12.8
10
-100
OFFSET FREQUENCY (Hz)
13
5
-80
-140
10
10
SSB Phase Noise vs. Reference Freq. &
Loop BW @ 12.9 GHz, Integer Mode
PHASE NOISE (dBc/Hz)
PHASE NOISE (dBc/Hz)
SSB Phase Noise Fractional
Spurs @ 12.902 GHz
-140
4
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
-130
10
PLLS w/ INTEGRATED VCO - SMT
-60
-50
0
10
20
30
TIME (μSEC)
40
50
0
50
100
150
200
250
300
FREQUENCY (MHz)
[1] R refers to the reference path division ratio
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6 - 47
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Frequency vs. Tuning Voltage, Vcc= +5V
14
14
13.6
13.6
OUTPUT FREQUENCY (GHz)
OUTPUT FREQUENCY (GHz)
Frequency vs. Tuning Voltage, T= 25°C
13.2
12.8
12.4
12
Vcc=4.75V
Vcc=5.0V
Vcc=5.25V
11.6
11.2
12.4
12
+25C
+85C
-40C
11.6
10.8
0
1
2
3
4
5
6
7
8
9
10
11
12
13
0
1
2
3
4
TUNING VOLTAGE (V)
6
6
7
8
9
10
11
12
13
10
11
12
13
Output Power
vs. Tuning Voltage, Vcc= +5V
800
12
OUTPUT POWER (dBm)
700
SENSITIVITY (MHz/V)
5
TUNING VOLTAGE (V)
Sensitivity vs. Tuning Voltage, Vcc= +5V
600
500
+25C
+85C
-40C
400
300
200
10
8
6
4
+25C
+85C
-40C
2
100
0
0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
0
1
2
3
4
TUNING VOLTAGE (V)
5
6
7
8
9
TUNING VOLTAGE (V)
Open Loop VCO SSB Phase Noise @
Vtune = +5V
Open Loop VCO SSB Phase Noise vs.
Tuning Voltage
0
0
-20
-40
SSB PHASE NOISE (dBC/Hz)
SSB PHASE NOISE (dBc/Hz)
PLLS w/ INTEGRATED VCO - SMT
12.8
11.2
10.8
+25C
+85C
-40C
-60
-80
-100
-120
-140
-160
-20
10 kHz Offset
100 kHz Offset
-40
-60
-80
-100
-120
10
3
10
4
10
5
10
OFFSET FREQUENCY (Hz)
6 - 48
13.2
6
10
7
1
2
3
4
5
6
7
8
9
10
TUNING VOLTAGE (V)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
12
13
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Pin Descriptions
Pin Number
Function
Description
1, 9 - 13, 22, 36
N/C
No Connection. These pins may be connected to RF/DC ground.
Performance will not be affected.
2 - 4, 7, 37, 39
GND [1]
These pins must be connected to RF/DC Ground
5
GND
These pins and package bottom
must be connected to RF/DC Ground
8
VCCVCO2 [2]
40
VCCVCO1
6
VTUNE
Control Voltage Input. Modulation port bandwidth
dependent on drive source impedance.
14
ACG
AC Ground. This pin must be connected to
an external capacitor to ground.
15
AVCC
Analog Power supply pin for the RF Section.
A decoupling capacitor to the ground plane should
be placed as close as possible to this pin. Nominally 3.3V
16
VDDCP
+5V Power Supply for charge pump digital section
+5V Power Supply for VCO
VCCCP
+5V Power Supply for the charge pump analog section
CP
Charge pump output
19
VDDPFD
Analog Power supply for the phase frequency detector, Nominally 3.3V
20
BIAS [3]
External bypass decoupling for precision bias circuits,
1.920V ±20 mV is generated internally
21
AVDD
Analog Power supply for analog ref paths, Nominally 3.3V
23
REFN
Reference input (Negative or AC coupled to GND)
24
REFP
Reference input (Positive)
25
RVDD
Ref path supply
26
DVDDQ
Digital supply for Substrate, Nominally 3.3V
27
CE
Chip Enable
28
SEN
Serial port latch enable input
29
SCK
Serial port clock input
30
SDI
Serial port data input
31
DVDD
Power supply pin for internal digital circuitry. Nominally 3.3V
32
VDDIO
Power Supply for digital I/O driver
33
LD_SDO
Lock Detect, Main Serial Data Output
or VCO Serial Port Data Out
34
VCCPS
Analog Power Supply for Prescaler, Nominally 3.3V
35
DVDDM
Digital Power Supply for M-Counter, Nominally 3.3V
38
RFOUT
RF output (AC coupled).
PLLS w/ INTEGRATED VCO - SMT
17
18
6
[1] This pin is not connected internally, however, this pin must be connected to GND to maintain product family pin for pin compatibility.
[2] This pin is not connected internally, however, this pin must be connected to Vcc to maintain product family pin for pin compatibility.
[3] BIAS ref voltage (pin 20) cannot drive an external load, and must be measured with a 10 GOhm meter such as Agilent 34410A; a typical
10 Mohm DVM will read erroneously.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6 - 49
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Pin Schematic Equivalents
Pins
Equivalent Schematic
RFOUT
VCCVCO1
6
PLLS w/ INTEGRATED VCO - SMT
VTUNE
6 - 50
GND
SEN, CE, SCK, SDI
LD_SDO
CP
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Pin Schematic Equivalents (Continued)
Pins
Equivalent Schematic
Bias
REFN, REFP
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLLS w/ INTEGRATED VCO - SMT
6
6 - 51
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Evaluation Circuit
3VDIGITAL
3VDIGITAL
C12
100NF
C10
10PF
C14
100NF
C13
10PF
C8
10PF
C9
100NF
CEN
2
R8
100K
3VANALOG
A
B
C
D
R20
1K
J3
1
C15
100PF
1
JP1
3VDIGITAL
RFout
50 Ohm Co-Planar Trace
5VVCO
U1
SDI
SCK
SEN
CE
DVDDQ
RVDD
REFP
REFN
NC
AVDD
11
12
13
14
15
16
17
18
19
20
C38
1NF
JP3
2
C32
4.7UF
NC
GND
GND
GND
GND
VTUNE
GND
VCCVCO2
NC
NC
30
29
28
27
26
25
24
23
22
21
C21
1NF
5016
GND
VCCVCO1
GND
RFOUT
GND
NC
DVDDM
VCCPS
LD_SDO
VDDIO
DVDD
1
2
3
4
5
6
7
8
9
10
SYNTH
5016
TP5
E
F
G
H
C35
100NF
C31
1
PLLS w/ INTEGRATED VCO - SMT
C1
1NF
1
SDO
40
39
38
37
36
35
34
33
32
31
C4
4.7UF
NC
NC
NC
ACG
AVCC
VDDCP
VCCCP
CP
VDDPFD
BIAS
TP6
JP2
6
2
LD
100PF
R23
C65
DEPOP
R27
DEPOP
0
C61
3.9NF
R28
DEPOP
L1
I
DEPOP
R21
R12
30
DEPOP
C62
R3
1K
C63
+15V
TP4
5016
TP3
5016
GND
DEPOP
FB4
C57
22UF
1000
C33
1.2NF
620
C64
J
C37
39NF
DEPOP
K
C58
4.7UF
C39
1NF
7
6
THS4031IDGN
4
R25
2
U5
FB3
1000
DEPOP
R13
200
R4
DEPOP
3
R26
R22
0
L
DEPOP
R15
10K
C60
1NF
R14
JP6
1
2
10K
6 - 52
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
M
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Evaluation Circuit (Continued)
Header to USB Board
J1
SCK
SDI
SDO
SEN
CEN
A
B
C
D
R1
100K
3VDIGITAL
1
2
3
4
5
6
7
8
9
10
11
12
NC
NC
NC
NC
TLW-106-05-T-D
3VDIGITAL
C7
100NF
C2
10PF
C3
100NF
3VANALOG
E
F
G
H
REFin
C29
50 Ohm Trace
R2
120
56
TCXO
C40
R6
3
FOUT
100NF
R7
120
Y2
VDD
VC
GND
R9
4
1
C6
10PF
C28
100NF
3VTCXO
10
R24
2
DEPOP
C30
DEPOP
R10
0
3VANALOG
I
C16
10PF
C18
100NF
C22
10PF
C23
100NF
C24
10PF
C25
100NF
C26
10PF
C27
100NF
3VANALOG
J
5VCP
K
M
J2
1
100NF
C34
100NF
L
6
3VANALOG
PLLS w/ INTEGRATED VCO - SMT
C5
10PF
5VCP
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6 - 53
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Evaluation Circuit (Continued)
5.5V
TP2
FB2
1000
5016
GND
C42
100NF
C59
4.7UF
TP1
FB1
1000
5016
R41
1K
JP5
1
R11
4.02K
PLLS w/ INTEGRATED VCO - SMT
6
U9
LP3878MR-ADJ
SD
2
R40
4.02K
C67
1.2NF
6
5
5VVCO
C36
100NF
ADJ
VIN
BPASS
VOUT
GND
4
C41
100NF
1
3
C73
10NF
U8
LP3878MR-ADJ
SD
R16
4.02K
5VCP
C44
1.2NF
6
5
ADJ
VIN
BPASS
VOUT
GND
8
4
1
3
C43
100NF
C48
4.7UF
C11
100NF
C17
4.7UF
C50
100NF
C49
4.7UF
C54
100NF
JP4
C53
4.7UF
C47
10NF
C45
4.7UF
U2
LP5900-3_3V
3VANALOG
C19
10PF
1
GND EN
6
U4
LP5900-3_3V
1
VOUT
C52
100NF
VIN
U6
LP5900-3_3V
1
C55
10PF
C56
100NF
VOUT
VIN
GND EN
6
4
GND EN
3
3VTCXO
R5
10K
4
3
3VDIGITAL
C51
10PF
VIN
VOUT
C20
100NF
3
R18
10K
6
4
R19
10K
1
6 - 54
C74
4.7UF
C68
4.7UF
R17
1K
C46
100NF
8
2
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Absolute Maximum Ratings
Nominal 3.3V Supplies to GND
-0.3V to +3.6V
Nominal Digital Supply to 3.3V
Analog Supply
-0.3V to +0.3V
Nominal 5V Supply to GND
-0.3 to +5.5V
Vtune
0 to +15V
Storage Temperature
-65 to +150°C
Max Peak Reflow Temperature
260 °C
ESD Rating
Class 1A
Reliability Information
Junction Temperature to Maintain
1 Million Hour MTTF
135 °C
Nominal Junction Temperature (T=85 °C)
120 °C
Thermal Resistance
(Junction to GND Paddle, 5V Supply)
34.2 °C/W
Operating Temperature
-40 to +85°C
6
PLLS w/ INTEGRATED VCO - SMT
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR
SUGGESTED PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
Package Marking [1]
HMC807LP6CE
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL3
H807
XXXX
[1] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6 - 55
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
Evaluation PCB
PLLS w/ INTEGRATED VCO - SMT
6
6 - 56
The circuit board used in the application should use RF circuit design techniques. Signal lines should have
50 Ohm impedance while the package ground leads and exposed paddle should be connected directly
to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the
top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC807LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH
INTEGRATED VCO, 12.4 - 13.4 GHz
List of Materials for Evaluation PCB 127283 [1]
Description
J1
Dual Row Terminal Strip
J2, J3
PCB Mount SMA RF Connector
JP1 - JP6
Single Row Terminal Strip
C1, C21, C38 - C39, C60
1000 pF Capacitor, 0402 Pkg.
C2, C5, C6, C8, C10, C13, C16,
C19, C22, C24, C26, C51, C55
10 pF Capacitor, 0402 Pkg.
C3, C7, C9, C11, C12, C14, C18, C20, C23,
C25, C27 - C29, C34 - C36, C40 - C43,
C46, C50, C52, C54, C56
0.1 μF Capacitor, 0402 Pkg.
C4, C17, C32, C45, C48,
C49, C53, C68, C74
4.7 μF Capacitor, 0805 Pkg.
C15, C31
100 pF Capacitor, 0402 Pkg.
C33, C44, C67
1200 pF Capacitor, 0402 Pkg.
C37
0.039 μF Capacitor, 0603 Pkg.
C47, C73
10,000 pF Capacitor, 0402 Pkg.
C57
22 μF Tantalum Capacitor, Case D
C58, C59
4.7 μF Tantalum Capacitor, Case B
C61
3900 pF Capacitor, 0402 Pkg.
FB1 - FB4
1000 Ohm 200 mA Ferrite Chip, 0805 Pkg.
R1, R8
100k Ohm Resistor, 0402 Pkg.
R2, R7
120 Ohm Resistor, 0402 Pkg.
R3, R17, R20, R41
1k Ohm Resistor, 0402 Pkg.
R4
620 Ohm Resistor, 0402 Pkg.
R5, R14, R15, R18, R19
10k Ohm Resistor, 0402 Pkg.
R6
56 Ohm Resistor, 0402 Pkg.
R9
10 Ohm Resistor, 0402 Pkg.
R10, R22, R23
Zero Ohm Resistor, 0402 Pkg.
R11, R16, R40
4.02k Ohm Resistor, 0402 Pkg.
R13
200 Ohm Resistor, 0402 Pkg.
R21
30 Ohm Resistor, 0402 Pkg.
TP1 - TP6
Test Point PC Compact SMT
U1
HMC764LP6CE Fractional-N Synthesizer,
with Integrated VCO
U2, U4, U6
Low Noise 3.3V, 100 mA Linear Regulator
U5
Low Noise Op-Amp, THS4031IDGN
U8, U9
5V, 800mA Voltage Regulator
Y2
3.3V, 50 MHz VCXO Crystal Oscillator
PCB [2]
125536 Evaluation Board
6
PLLS w/ INTEGRATED VCO - SMT
Item
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6 - 57