HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz Features • RF Bandwidth: 1285 to 1415 MHz • 24-bit Step Size, Resolution 3 Hz typ • Fractional or Integer Modes • 200 MHz, 14-bit Reference Path Input • 19-Bit Prescaler • Cycle Slip Prevention • Ultra Low Phase Noise -108 dBc/Hz in Band Typ. • Read / Write Serial Port, Chip ID • 40 Lead 6x6mm SMT Package: 36mm2 • Figure of Merit (FOM) -227 dBc Integer Typical Applications PLLS w/ INTEGRATED VCO - SMT 12 12 - 110 • Cellular/4G Infrastructure • Phased Array Applications • Repeaters and Femtocells • DDS Replacement • Communications Test Equipment • Very High Data Rate Radios • CATV Equipment Functional Diagram For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz General Description The HMC828LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an Integrated Voltage Controlled Oscillator (VCO). The synthesizer consists of an integrated low noise VCO with divideby-2 output, an autocalibration subsystem for low voltage VCO tuning, a very low noise digital Phase Detector (PD), a precision controlled charge pump, a low noise reference path divider and a fractional divider. The fractional synthesizer features an advanced delta-sigma modulator design that allows both ultra-fine step sizes and low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow faster frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for faster frequency hopping and low micro-phonics. For theory of operation and register map refer to the “PLLs w/ Integrated VCOs - RF VCOs” Operating Guide. To view the Operating Guide, please visit www.hittite.com and choose HMC828LP6CE from the “Search by Part Number” pull down menu. VPPCP, VDDCP, VCC1, VCC2 = 5V ±4%; RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V ±6% GNDCP = GNDLS = Ground Paddle = 0V Parameter Condition Min. Typ. Max. Units MHz RF Output Characteristics VCO Frequency at PLL Input 2570 2830 RF Output Frequency at f VCO/2 1285 1415 MHz 13 dBm 1.5 MHz/V RF Output Power at f VCO/2 7 VCO Tuning Sensitivity Measured at 2 GHz, 2V VCO Supply Pushing Measured at 2 GHz, 2V 10 15 -2 MHz/V RF Output 2nd Harmonic -25 dBc RF Output 3rd Harmonic -23 dBc RF Output 4th Harmonic -31 dBc RF Divider Characteristics 19-Bit N-Divider Range (Integer) 19-Bit N-Divider Range (Fractional) Max = 219 - 1 16 524,287 Fractional nominal divide ratio varies (-3 / +4) dynamically max 20 524,283 REF Input Characteristics Max Rep Input Frequency 200 MHz Max Ref Frequency with AutoCal 54 MHz Min Ref Input Frequency 100 kHz Ref Input Range AC Coupled 1.5 2 Ref Input Capacitance 14-Bit R-Divider Range 3.3 Vpp 5 pF 1 16,383 PLLS w/ INTEGRATED VCO - SMT 12 Electrical Specifi cations, TA = +25° C Phase Detector (PD) PD Frequency Fractional Mode Max PD Freq. Min VCO Freq/20 0.1 TBD MHz PD Frequency Integer Mode Max PD Freq. Min VCO Freq/16 0.1 110 MHz Charge Pump Max Output Current 2.54 Min Output Current 20 μA Charge Pump Gain Step Size (5-Bits) 20 μA Charge Pump Trim Step Size (4-Bits) 5 μA For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA 12 - 111 HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz Electrical Specifi cations (Continued) Parameter Condition Min. Charge Pump Trim Step Size (3-Bits) Typ. Max. Units 7 μA 55 μA 1 kHz -141 dBc/Hz 10 kHz -149 dBc/Hz 100 kHz -155 dBc/Hz Charge Pump Offset Step Size (4-Bits) PD/Charge Pump Noise 50 MHz Ref, Input Referred, Integer, add 6 dB for Fractional Less than 3 dB degradation typ. at these limits Compliance Voltage PLLS w/ INTEGRATED VCO - SMT 12 -385 μA Offset 0.4 VPPCP-0.8 V +385 μA Offset 0.8 VPPCP-0.4 V VIH Input High Voltage DVDD3V-0.4 DVDD3V V VIL Input Low Voltage 0 0.4 V VOH Output High Voltage DVDD3V-0.4 DVDD3V V VOL Output Low Voltage 0 0.4 V 3.5 V Logic Inputs Logic Outputs Power Supply Voltages AVDD, VCCHF, VCCPS, VCCPD, RVDD 3.0 3.3 DVDD3V 3.0 3.3 3.5 V VPPCP, VDDCP, VCC1, VCC2 4.8 5 5.2 V Analog 3.3V Supplies Digital Supply Analog 5V Supplies Power Supply Currents +5V Analog Charge Pump VPPCP, VDDCP 5.3 mA +5V VCO Core and PLL Buffer VCC2 56 mA +5V VCO Divider and RF Buffer VCC1 36 mA AVDD, VCCHF, VCCPS, VCCPD, RVDD 45 mA +3.3V Analog +3.3V Digital Power Down - Crystal Off Power Down - Crystal On, 100 MHz DVDD3V 6.5 mA Reg 01h=0, Crystal Not Clocked 10 μA Reg 01h=0, Crystal Clocked 100 MHz 10 200 μA Power on Reset Typical Reset Voltage on DVDD Min DVDD Voltage for No Reset 700 mV 250 μs 1.5 Power on Reset Delay V VCO Open Loop Phase Noise at fvco/2 1 GHz Divide-by-2 Output 10 kHz Offset -88 dBc/Hz 1 GHz Divide-by-2 Output 100 kHz Offset -118 dBc/Hz 1 GHz Divide-by-2 Output 1 MHz Offset -143 1 GHz Divide-by-2 Output 10 MHz Offset -162 -141 dBc/Hz dBc/Hz 1 GHz Divide-by-2 Output 100 MHz Offset -168 dBc/Hz 1 kHz Offset -105 dBc/Hz Closed Loop Phase Noise PLL + VCO at fvco/2 Integer, 25 MHz PFD 12 - 112 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz Electrical Specifi cations (Continued) Parameter Condition Integer, 25 MHz PFD 10 kHz Offset Integer, 25 MHz PFD Integer, 25 MHz PFD Fractional, 25 MHz PFD Fractional, 25 MHz PFD Figure of Merit Min. Typ. Max. Units -112 dBc/Hz 100 kHz Offset -120 dBc/Hz 1 MHz Offset -103 dBc/Hz 10 kHz Offset -107 dBc/Hz 100 kHz Offset -112 dBc/Hz Normalized 1 Hz Integer Mode Measured w/ 50 MHz PD at 30 kHz Offset -227 dBc/Hz Fractional Mode Measured w/ 50 MHz PD at 30 kHz Offset -225 dBc/Hz Closed Loop Integer Phase Noise -80 -80 -90 1250 MHz 1350 MHz -100 PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) -90 -110 -120 -130 -140 -150 -110 -120 -130 -140 -150 -160 -160 -170 -170 -180 2 10 10 3 10 4 10 5 10 6 10 7 10 1285 MHz 1345 MHz -100 -180 2 10 8 10 3 FREQUENCY OFFSET (Hz) 10 4 10 5 10 6 10 7 10 8 FREQUENCY OFFSET (Hz) Typical VCO/2 Tuning Curves vs. Switch Position VCO/2 Free Running Phase Noise -20 fmax 1275 MHz 1350 MHz 1450 MHz -60 -80 n0 -100 -120 n2 n4 n6 n8 n10 n12 n14 n16 n18 n20 n22 n24 n26 kvco (MHz/V) PHASE NOISE (dBc/Hz) -40 -140 fmin n30 n30 PLLS w/ INTEGRATED VCO - SMT 12 Typical Closed Loop Fractional Phase Noise [1] n31 -160 -180 100 1000 10 4 10 5 10 6 FREQUENCY OFFSET (Hz) 10 7 10 8 0 1 2 3 4 5 TUNING VOLTAGE (V) [1] Fractional Mode, 50 MHz Crystal, R=1, ~80 kHz Loop BW, (Loop filter values: Contact factory for component values) 2mA Charge Pump, -385μA Offset. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 113 HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz -110 100kHz Offset PHASE NOISE (dBc/Hz) -120 -40C +27C +85C -130 1MHz Offset -140 -150 10MHz Offset -160 -170 1200 1250 1300 1350 1400 1450 1500 TUNE VOLTAGE AFTER CALIBRATION (V) Typical VCO Tuning Voltage After Calibration Free Running VCO Phase Noise (VTUNE Set by AutoCal) 5 4 Fmin 3 31 Fmax 15 0 2 1 0 FREQUENCY (MHz) VCO FREQUENCY Typical VCO Sensitivity vs. Cap @ Fo Voltage Typical Output Power - Narrow Band Match 60 15 TUNING CAP 31, Fmin AT 2V TUNING CAP 15, Fmid AT 2V TUNING CAP 0, Fmax AT 2V 40 30 OUTPUT POWER (dBm) kvco (MHz/V) 50 Typical Operating Range 20 10 5 10 0 0 1 2 3 4 0 1250 5 TUNING VOLTAGE (V) 1300 1350 1400 1450 OUTPUT FREQUENCY (MHz) Figure of Merit -200 NORMALIZED PHASE NOISE (dBc/Hz) PLLS w/ INTEGRATED VCO - SMT 12 -210 Typ FOM vs Offset -220 FOM Floor FOM 1/f Noise -230 -240 100 1000 10 4 10 5 10 6 FREQUENCY OFFSET (Hz) [1] Fractional Mode, 50 MHz Crystal, R=1, ~80 kHz Loop BW, (Loop filter values: Contact factory for component values) 2mA Charge Pump, -385μA Offset. 12 - 114 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz Pin Descriptions Function Description 1 AVDD DC Power Supply for analog circuitry. 2, 5, 6, 8, 9, 11 - 14, 18 - 22, 24, 26, 34, 37, 38 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 3 VPPCP Power Supply for charge pump analog section 4 CP Charge Pump Output 7 VDDCP Power Supply for the charge pump digital section 10 RVDD Reference Supply 15 XREFP Reference Oscillator Input 16 DVDD3V DC Power Supply for Digital (CMOS) Circuitry 17 CEN Chip Enable. Connect to logic high for normal operation. 23 VTUNE VCO Varactor. Tuning Port Input. 25 VCC2 VCO Analog Supply 2 27 VCC1 VCO Analog Supply 1 28 RF_N VCO Divide by 2 RF Positive Output 29 RF_P VCO Divide by 2 RF Negative Output 30 SEN PLL Serial Port Enable (CMOS) Logic Input 31 SDI PLL Serial Port Data (CMOS) Logic Input 32 SCK PLL Serial Port Clock (CMOS) Logic Input 33 LD_SDO Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO) 35 VCCHF DC Power Supply for Analog Circuitry 36 VCCPS DC Power Supply for Analog Prescaler 39 VCCPD DC Power Supply for Phase Detector BIAS External bypass decoupling for precision bias circuits. Note: 1.920V ±20mV reference voltage (BIAS) is generated internally and cannot drive an external load. Must be measured with 10GΩ meter such as Agilent 34410A, normal 10MΩ DVM will read erroneously. 40 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 PLLS w/ INTEGRATED VCO - SMT Pin Number 12 - 115 HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz Absolute Maximum Ratings AVDD, RVDD, DVDD3V, VCCPD, VCCHF, VCCPS -0.3V to +3.6V VPPCP, VDDCP, VCC1 -0.3V to +5.8V VCC2 -0.3V to +5.5V Operating Temperature -40°C to +85°C Storage Temperature -65°C to 125°C Maximum Junction Temperature 150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Reflow Soldering Peak Temperature 260°C Time at Peak Temperature 40 sec ESD Sensitivity (HBM) Class 1B PLLS w/ INTEGRATED VCO - SMT 12 Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [1] HMC828LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL3 H828 XXXX [1] 4-Digit lot number XXXX 12 - 116 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com PLLS w/ INTEGRATED VCO - SMT 12 12 - 117 HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz List of Materials for Evaluation PCB 128147 [1] Item PLLS w/ INTEGRATED VCO - SMT 12 12 - 118 Description J1, J2 PCB Mount SMA RF Connector J3 Dual Row Terminal Strip J4, J5 Connector Header C1, C15 - C17, C25, C29 10 μF Capacitor, 0805 Pkg. C2, C3, C6, C7, C11, C12, C14, C18, C27, C43 0.47 μF Capacitor, 0402 Pkg. C4, C13 22 pF Capacitor, 0402 Pkg. C5, C33 1000 pF Capacitor, 0402 Pkg. C8 1.5 pF Capacitor, 0402 Pkg. C19 - C24, C28, C30 - C32, C34 0.1 μF Capacitor, 0402 Pkg. C26 1.0 μF Capacitor, 0603 Pkg. C35 3300 pF Capacitor, 0402 Pkg. C36 270 pF Capacitor, 0402 Pkg. C37, C38 68 pF Capacitor, 0402 Pkg. C39 - C42 4.7 μF Tantalum Capacitor, 0805 Pkg FB1 - FB2 1000 Ohm 200 mA Ferrite Chip, 0805 Pkg. R1, R2, R5, R11, R15, R18, R19 Zero Ohm Resistor, 0402 Pkg. R3, R4, R6, R7 1 kOhm Resistor, 0402 Pkg. R8 22 Ohm Resistor, 0402 Pkg. R12, R20, R23 51 Ohm Resistor, 0402 Pkg. R22, R25 20 kOhm Resistor, 0402 Pkg. R24 10 Ohm Resistor, 0402 Pkg. R26 - R28 1k Ohm Resistor, 0402 Pkg. L1 12 nH Inductor, 0402 Pkg. TP3, TP4 Test Point PC Compact SMT U1 HMC828LP6CE PLL with Integrated VCO U2 Low Noise Quad Adjustable Linear Regulator Y1 3.3V, 50 MHz VCXO Crystal Oscillator PCB [2] 125998 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC828LP6CE v02.1109 FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 1285 - 1415 MHz Notes: PLLS w/ INTEGRATED VCO - SMT 12 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 119