Amp’ed RF, Inc. Preliminary (phone) 408 213-9530 (fax) 408 213-9533 Product Specification Features 15mm x 27mm Description The added class 1 power, +16dBm, of the BT-11, gives this module one of the best ranges in the industry. It’s completely pin compatible with the lower power BT-21, and offers a second power choice on the same design. The BT-11 module includes 16 general purpose input/output lines, several serial interface options, analog-to-digital inputs, and up to 2M bps data throughput. The BT-11 is a surface mount PCB module that provides fully embedded, ready to use Bluetooth wireless technology. The reprogrammable flash memory contains embedded firmware for serial cable replacement using the Bluetooth SPP profile. Other popular Bluetooth profiles, such as OBEX, are also available. Customized firmware for peripheral device interaction, power optimization, security, and other proprietary features may be supported and can be ordered pre-loaded and configured. Additional Documentation BT Hardware Design Guide abSerial User Guide abSerial Reference Guide ©2008 Amp’ed RF Inc 1 10/07/08 - Bluetooth Radio Fully embedded Bluetooth v2.1+EDR with profiles Class 1 radio Complete RF ready module Wireless data communications Integrated chip antenna 128-bit encryption security Range up to 120m LOS FCC & Bluetooth qualified Integrated antenna or with coaxial external connector ST Micro Cortex-M3 microprocessor up to 70MHz Memory 256K bytes flash memory 48K bytes RAM memory Data Rate 2M bps maximum data rate Multipoint capability up to 7 slaves Serial Interface UART, up to 3.25M bps SPI interface I2C interface USB v2.0 General I/O 16 general purpose I/O 4x12-bit A/D inputs 1 DAC output User Interface AT command set Firmware upgrade over UART 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 1 of 12 Amp’ed RF, Inc. Preliminary (phone) 408 213-9530 (fax) 408 213-9533 Software Architecture Upper Layer Stack: Amp’ed UP Lower Layer Stack Full Bluetooth v2.1+EDR data rate (3M bps maximum) Device power modes—active, sleep and deep sleep Wake on Bluetooth feature—optimized power consumption of host CPU Authentication and encryption Encryption key length from 8-bits to 128-bits maximum Persistent FLASH memory—for BD Address and radio parameter storage All ACL (Asynchronous Connection Less) packet types (DM1, DH1, DM3, DH3, DM5, DH5, 2-DH1, 2-DH3, 2-DH5, 3-DH1 3-DH3, 3-DH5, AUX1) SCO (Synchronous Connection Oriented) packet types (HV1, HV2, HV3) Point to multipoint and scatternet support—3 master and 7 slave links allowed (10 active links simultaneously) Park, sniff, and hold modes—fully supported to maximum allowed intervals Master slave switch—supported during connection and post connection Dedicated Inquiry Access Code—for improved inquiry scan performance Dynamic packet selection—channel quality driven data rate to optimize link performance Dynamic power control—interference reduction and link performance Bluetooth test modes—per Bluetooth specification 802.11b co-existence—AWMA and AFH Vendor specific HCI commands—to support device configuration and certification test modes SPP, OBEX, SDAP, GAP, and DUN protocols RFComm, SDP, and L2CAP supported Multipoint with 7 simultaneous slaves HCI Interface Bluetooth v2.1 specification compliant HCI UART transport layer (H4) UI Application AT Commands Custom Applications BT profiles SPP, OBEX, DUN, GAP HCI (over UART) SDP RFComm Upper layer stack + BT profiles: Amp’ed UP! L2CAP HCI HCI LMP Low-level BT stack embedded in Bluetooth IC BT PHY ©2008 Amp’ed RF Inc 2 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 2 of 12 Preliminary Amp’ed RF, Inc. (phone) 408 213-9530 (fax) 408 213-9533 Hardware Specifications General Conditions (VIN= 3.0V and 25°C) Recommended Operating Conditions Rating Operating Temperature Range Min -30 Typical - Max 80 Unit °C Supply Voltage VIN 2.7 3.0 3.6 Volts Signal Pin Voltage - 3.0 - Volts 2400 - 2483.5 MHz RF Frequency Absolute Maximum Ratings Rating Storage temperature range Min -55 Typical - Max +150 Unit °C Supply voltage, VIN -0.3 - + 3.6 Volts I/O pin voltage, VIO -0.3 - + 4.0 Volts - - -5 dBm RF input power Current Consumption Modes Typical Power Consumption Avg Unit ACL data 115K Baud UART at max throughput (Master) 58.0 mA ACL data 115K Baud UART at max throughput (Slave) 55.0 mA Connection, no data traffic, master 26.0 mA Connection, no data traffic, slave 34.0 mA Connection in sniff (Tsniff=100ms), no data traffic, master 12.0 mA Connection in sniff (Tsniff=100ms), no data traffic, slave 12.4 mA Connection in sniff (Tsniff=375ms), no data traffic, master 3.0 mA Connection in sniff (Tsniff=375ms), no data traffic, slave 3.5 mA Standby, without deep sleep 21.0 mA Standby, with deep sleep 0.240 mA 2.4 mA Page/Inquiry scan, deep sleep ©2008 Amp’ed RF Inc 3 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 3 of 12 Preliminary Amp’ed RF, Inc. (phone) 408 213-9530 (fax) 408 213-9533 I/O Operating Characteristics Symbol Parameter Min Max Unit VIL Low-Level Input Voltage - 0.9 Volts VIN, 3.0V Conditions VIH High-Level Input Voltage 2.1 - Volts VIN, 3.0V VOL Low-Level Output Voltage - 0.4 Volts VIN, 3.0V VOH High-Level Output Voltage 2.2 - Volts VIN, 3.0V IOL Low -Level Output Current - 8.0 mA VOL = 0.4 V IOH High-Level Output Current - 8.0 mA VOH = 2.2 V RPU Pull-up Resistor 50 150 KΩ Resistor Turned On RPD Pull-down Resistor 50 150 KΩ Resistor Turned On Selected RF Characteristics Parameters Conditions BT Spec Antenna load Typical Unit 50 ohm Radio Receiver Sensitivity level BER < .001 with DH5 ≤ -70 -90 dBm Maximum usable level BER < .001 with DH1 ≥ -20 -9 dBm Input VSWR 2.5:1 Radio Transmitter Maximum output power Initial Carrier Frequency Tolerance 20 dB Bandwidth for modulated carrier ©2008 Amp’ed RF Inc 4 10/07/08 50 Ω load <+20 +16 dBm ± 75 0 kHz ≤ 1000 932 kHz 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 4 of 12 Preliminary Amp’ed RF, Inc. (phone) 408 213-9530 (fax) 408 213-9533 Pin Assignment Name Type UART Interface Pin # Description RXD I 8 Receive data TXD O 6 Transmit data ALT Function CTS I 9 Clear to send (active low) RTS O 10 Request to send (active low) I 2 Boot Loader (active high) Boot Loader Boot 0 Power and Ground VDD 24 VDD GND 23 GND 3 Reset input (active low for 5 ms); Reset RESETN I GPIO – General Purpose Input/Output GPIO [0] I/O 16 General Purpose Input/Output SPI MISO GPIO [1] I/O 17 General Purpose Input/Output SPI MOSI GPIO [2] I/O 19 General Purpose Input/Output SPI SS GPIO [3] I/O 1 General Purpose Input/Output SPI CLK GPIO [4] I/O 18 General Purpose Input/Output UART 2 RXD GPIO [5] I/O 20 General Purpose Input/Output UART 2 TXD GPIO [6] I/O 22 General Purpose Input/Output ADC 0 GPIO [7] I/O 13 General Purpose Input/Output ADC 1 GPIO [8] I/O 4 General Purpose Input/Output ADC 2 GPIO [9] I/O 7 General Purpose Input/Output ADC 3 GPIO [10] I/O 5 General Purpose Input/Output GPIO [11] I/O 11 General Purpose Input/Output I2C SCL GPIO [12] I/O 12 General Purpose Input/Output I2C SDA GPIO [13] I/O 15 General Purpose Input/Output GPIO [14] I/O 14 General Purpose Input/Output GPIO [15] I/O 21 General Purpose Input/Output ©2008 Amp’ed RF Inc 5 10/07/08 DAC 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 5 of 12 Preliminary Amp’ed RF, Inc. (phone) 408 213-9530 (fax) 408 213-9533 BT-11 Drawing ©2008 Amp’ed RF Inc 6 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 6 of 12 Amp’ed RF, Inc. Preliminary (phone) 408 213-9530 (fax) 408 213-9533 Hardware Block Diagram Battery or supply Regulator 2.75V 2.75V SPI PA/ LNA BP Filter STLC2500D RAM ROM 26 MHz Crystal UART ARM MCU Reset BT_WakeUp I2C GPIO 256K/Flash 48K/RAM UART BT stack up to HCI Amp’ed UP - abSerial/Application - GAP, SPP, DUN, OBEX - SDP/RFCOMM - L2CAP BT-11 Bluetooth Module Block Diagram ©2008 Amp’ed RF Inc 7 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 7 of 12 Preliminary Amp’ed RF, Inc. (phone) 408 213-9530 (fax) 408 213-9533 Hardware Design Amp’ed RF modules support UART, USB, SPI, I2C and GPIO hardware interfaces. Note that the usage of these interfaces is dependant upon the firmware that is loaded into the module, and is beyond the scope of this document. Notes All unused pins should be left floating; do not ground. All GND pins must be well grounded. The area around the module should be free of any ground planes, power planes, trace routings, or metal for 8 mm from the antenna in all directions. Traces should not be routed underneath the module. Module Reflow Installation The BT-11 is a surface mount Bluetooth module supplied on a 24 pin, 6-layer PCB. The final assembly recommended reflow profiles are: For non Pb-free applications, Sn63Pb37 solder is recommended. Maximum peak temperature of 208° - 210°C (below 220°C). Maximum rise and fall slope after liquidous of < 2°C/second. Maximum rise and fall slope after liquidous of < 2°C/second. Maximum time at liquidous of 50 – 90 seconds. For RoHS/Pb-free applications, Sn96.5/Ag3.0/Cu0.5 solder is recommended. Maximum peak temperature of 230° - 240°C (below 250°C). Maximum rise and fall slope after liquidous of < 2°C/second. Maximum rise and fall slope after liquidous of < 3°C/second. Maximum time at liquidous of 40 – 80 seconds. ©2008 Amp’ed RF Inc 8 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 8 of 12 Preliminary Amp’ed RF, Inc. (phone) 408 213-9530 (fax) 408 213-9533 GPIO Interface All GPIOs are capable of sinking and sourcing 8mA of I/O current. GPIO [0] to GPIO [7] are internally pulled down with 100KΩ (nominal) resistors GPIO [8] to GPIO [15] are internally pulled up with 100KΩ (nominal) resistors. UART Interface The UART is compatible with the 16550 industry standard. Four signals are provided with the UART interface. The TXD and RXD pins are used for data while the CTS and RTS pins are used for flow control. Host CTS RXD TXD RTS RXD CTS RTS TXD Amp’ed RF Module Connection to Host Device ©2008 Amp’ed RF Inc 9 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 9 of 12 Amp’ed RF, Inc. Preliminary (phone) 408 213-9530 (fax) 408 213-9533 Amp’ed RF Module Typical RS232 Circuit ©2008 Amp’ed RF Inc 10 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 10 of 12 Preliminary Amp’ed RF, Inc. (phone) 408 213-9530 (fax) 408 213-9533 PCB Layout Guidelines ©2008 Amp’ed RF Inc 11 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 11 of 12 Preliminary Amp’ed RF, Inc. (phone) 408 213-9530 (fax) 408 213-9533 FCC Regulatory Compliance This module has been tested and found to comply with the FCC Part15 Rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications or changes to this equipment not expressly approved by Amp’ed RF may void the user’s authority to operate this equipment. Modular Approval FCC ID: WDTBTMOD1 In accordance with FCC Part 15, the BT-11 is listed above as a Modular Transmitter device. FCC Label Instructions The outside of final products that contain a BT-11 device must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: WDTBTMOD2 or “Contains FCC ID: WDTBTMOD1. Any similar wording that expresses the same meaning may be used. ©2008 Amp’ed RF Inc 12 10/07/08 1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA www.ampedrf.com BT-11 Datasheet Page 12 of 12