Mag Com 2>.Designed to meet Supplementary Insulation .530 13,46 MAX .605 15,37 .100 2,54 XXXX HK 1>.Designed for use with ADI'S AD20MSP910 IC Chip EX-1030 Features 10 X .028 ± .002 0,71 ± 0,05 .695 17,65 MAX Mag.C om ADSL Transformer EX-1030S .098 2,50 .098 2,50 10 X .051 ± .002 1,30 ± 0,05 Requirements of IEC950 for 250 VAC Working Voltage .522 13,25MAX 3>.Good Total Harmonic Distortion Characteristics .394 10,00 .394 10,00 Optimized Design for Size and Performance .485 12,32 MAX Customization Available 4>.Available in Tape and Reel o 5>.232 C Peak infrared reflow temperature rating .005/0,13 10 SURFACES Schematic 10 1 6>.Cross reference to Pulse B2032 A Specifications Designed to reflect 100 ohms on the PRI with 100 ohms on the SEC D.C. Resistance 20oC : (1-3): 1.10 ohms + _10% (2-4): 1.50ohms+ _10% (10-8): 1.29ohms+ _10% (9-7): 1.29ohms+ _10% Longitudinal Balance: 40 dB min., @25kHz - 1.1 MHz PRI 3 Line 2 D 4 B C 8 SEC 9 Device 7 Frequency Response: +_1.0 dB , 30 kHz - 1.1 MHz Insertion Loss: 0.5 dB max. @ 100 kHz Dielectric Test: 1875 VAC 0.5mA 1sec , PRI - SEC Inductance: 5.0 mH + _5%, 10 kHz, 1.0 VAC, 1-4(tie 2+3), Ls Leakage Inductance: 18 uH max, 100 kHz, 100 mVAC, 1-4(tie 2+3, 8+9, 7+10), Ls THD(Linearity) : -80dB @30KHZ,-60dB @300KHZ Turns Ratio: (10-8):(9-7) = 1:1 + _1% (10-7):(1-4) = 1:1, tie (2+3, 8+9), + _1% Scale:Do not scale DWG Unspecified tolerance Title ADSL TRANSFORMER Unit :inch/mm .x +/- .xx+/- Unisen P/N EX-1030S DWG BY : .xxx+/-.010/0.25 +/- Part NO. N/A CHK BY : DWG NO. E00019 Appro. BY : Sheet 1 of 2 REV. Mag Com ADSL Transformer EX-1030S Winding Barrel Shelf Crossover Magnetwire Turns Hold Down Wrapper Finish A 1 B 5(2X2L) C D 5(2X4L) 1 1 5(2X2L) 1 2 3 6 6 2 50T 3(2L) 6 3 6 2 50T Bifi 50T 4 Apply shelf tape against each bobbin flange. Wind wires across the bobbin in 2 even layers. Wind wires across the bobbin in 4 even layers. Wires must be off of shelves before they enter the core window area.Shelves 1.5mm form core. 3(2L) 3(2L) Gap Materials: 1. Bobbin: EP13 SMD 10pin 1sec 2. Core: EP13 Ui=10000 Al=500nH/T2 3. Tape: PZ-280 7.9mm WID for finishing and wrapping winding 4. Tape: PZ-280 7.0mm WID for wrapping core 5. Shelf tape: WF2901 1.4mm WID 0.15mmTH o 6. Wire: Magnetic wire AWG#35 SGL 155 C 7. Varnish: #31-398 2 OF 2