ETC RCM3200

RabbitCore RCM3200
C-Programmable Module with Ethernet
User’s Manual
019–0118
• 031205–F
RabbitCore RCM3200 User’s Manual
Part Number 019-0118 • 031205–F • Printed in U.S.A.
©2002–2003 Z-World Inc. • All rights reserved.
Z-World reserves the right to make changes and
improvements to its products without providing notice.
Trademarks
Rabbit and Rabbit 3000 are registered trademarks of Rabbit Semiconductor.
RabbitCore is a trademark of Rabbit Semiconductor.
Dynamic C is a registered trademark of Z-World Inc.
Z-World, Inc.
Rabbit Semiconductor
2900 Spafford Street
Davis, California 95616-6800
USA
2932 Spafford Street
Davis, California 95616-6800
USA
Telephone: (530) 757-3737
Fax: (530) 757-3792
Telephone: (530) 757-8400
Fax: (530) 757-8402
www.zworld.com
www.rabbitsemiconductor.com
RabbitCore RCM3200
TABLE OF CONTENTS
Chapter 1. Introduction
1
1.1 RCM3200 Features ...............................................................................................................................1
1.2 Advantages of the RCM3200 ...............................................................................................................2
1.3 Development and Evaluation Tools......................................................................................................2
1.4 How to Use This Manual ......................................................................................................................3
1.4.1 Additional Product Information ....................................................................................................3
1.4.2 Online Documentation ..................................................................................................................3
Chapter 2. Hardware Reference
5
2.1 RCM3200 Digital Inputs and Outputs ..................................................................................................6
2.1.1 Memory I/O Interface .................................................................................................................11
2.1.2 Other Inputs and Outputs ............................................................................................................11
2.2 Serial Communication ........................................................................................................................12
2.2.1 Serial Ports ..................................................................................................................................12
2.2.2 Ethernet Port ...............................................................................................................................12
2.2.3 Programming Port .......................................................................................................................13
2.2.3.1 Alternate Uses of the Programming Port ........................................................................... 13
2.3 Programming Cable ............................................................................................................................14
2.3.1 Changing from Program Mode to Run Mode .............................................................................14
2.3.2 Changing from Run Mode to Program Mode .............................................................................14
2.4 Other Hardware...................................................................................................................................15
2.4.1 Clock Doubler .............................................................................................................................15
2.4.2 Spectrum Spreader ......................................................................................................................15
2.5 Memory...............................................................................................................................................16
2.5.1 SRAM .........................................................................................................................................16
2.5.2 Flash EPROM .............................................................................................................................16
2.5.3 Dynamic C BIOS Source Files ...................................................................................................16
Chapter 3. Software Reference
17
3.1 More About Dynamic C .....................................................................................................................17
3.2 Dynamic C Functions .........................................................................................................................18
3.2.1 Board Initialization .....................................................................................................................18
3.2.2 Digital I/O ...................................................................................................................................19
3.2.3 Serial Communication Drivers....................................................................................................19
3.2.4 TCP/IP Drivers............................................................................................................................19
3.3 Sample Programs ................................................................................................................................20
3.4 Upgrading Dynamic C ........................................................................................................................21
3.4.1 Add-On Modules.........................................................................................................................21
Appendix A. RCM3200 Specifications
23
A.1 Electrical and Mechanical Characteristics .........................................................................................24
A.1.1 Headers.......................................................................................................................................27
A.1.2 Physical Mounting .....................................................................................................................27
A.2 Bus Loading .......................................................................................................................................28
A.3 Rabbit 3000 DC Characteristics.........................................................................................................31
A.4 I/O Buffer Sourcing and Sinking Limit .............................................................................................32
A.5 Conformal Coating.............................................................................................................................33
A.6 Jumper Configurations.......................................................................................................................34
User’s Manual
Appendix B. Prototyping Board
35
B.1 Mechanical Dimensions and Layout ................................................................................................. 36
B.2 Power Supply..................................................................................................................................... 37
B.3 Using the Prototyping Board ............................................................................................................. 38
B.3.1 Adding Other Components ........................................................................................................ 39
B.3.2 Measuring Current Draw ........................................................................................................... 39
B.3.3 Other Prototyping Board Modules and Options ........................................................................ 39
Appendix C. LCD/Keypad Module
41
C.1 Specifications..................................................................................................................................... 41
C.2 Contrast Adjustments for All Boards ................................................................................................ 43
C.3 Keypad Labeling................................................................................................................................ 44
C.4 Header Pinouts................................................................................................................................... 45
C.4.1 I/O Address Assignments .......................................................................................................... 45
C.5 Mounting LCD/Keypad Module on the Prototyping Board.............................................................. 46
C.6 Bezel-Mount Installation ................................................................................................................... 47
C.6.1 Connect the LCD/Keypad Module to Your Prototyping Board ................................................ 49
C.7 LCD/Keypad Module Function APIs ................................................................................................ 50
C.7.1 LEDs .......................................................................................................................................... 50
C.7.2 LCD Display .............................................................................................................................. 51
C.7.3 Keypad ....................................................................................................................................... 67
C.8 Sample Programs............................................................................................................................... 70
Appendix D. Power Supply
71
D.1 Power Supplies .................................................................................................................................. 71
D.1.1 Battery-Backup Circuits ............................................................................................................ 71
D.1.2 Reset Generator ......................................................................................................................... 72
D.2 Optional +5 V Output........................................................................................................................ 72
Appendix E. Programming Cable
73
Appendix F. Motor Control Option
77
F.1 Overview ............................................................................................................................................ 77
F.2 Header J6............................................................................................................................................ 78
F.3 Using Parallel Port F .......................................................................................................................... 79
F.3.1 Parallel Port F Registers............................................................................................................. 79
F.4 PWM Outputs .................................................................................................................................... 82
F.5 PWM Registers .................................................................................................................................. 83
F.6 Quadrature Decoder ........................................................................................................................... 84
Notice to Users
87
Index
89
Schematics
91
RabbitCore RCM3200
1. INTRODUCTION
The RCM3200 RabbitCore module is designed to be the heart of
embedded control systems. The RCM3200 features an integrated 10/100Base-T Ethernet port and provides for LAN and
Internet-enabled systems to be built as easily as serial-communication systems.
The RCM3200 has a Rabbit 3000® microprocessor operating at 44.2 MHz, data and program execution SRAM, flash memory, two clocks (main oscillator and timekeeping), and
the circuitry necessary for reset and management of battery backup of the Rabbit 3000’s
internal real-time clock and the data SRAM. Two 34-pin headers bring out the Rabbit
3000 I/O bus lines, parallel ports, and serial ports.
The RCM3200 receives its +3.3 V power from the customer-supplied motherboard on
which it is mounted. The RabbitCore RCM3200 can interface with all kinds of CMOScompatible digital devices through the motherboard.
1.1 RCM3200 Features
• Small size: 1.85" × 2.65" × 0.86"
(47 mm × 67 mm × 22 mm)
• Microprocessor: Rabbit 3000 running at 44.2 MHz
• 52 parallel 5 V tolerant I/O lines: 44 configurable for I/O, 4 fixed inputs, 4 fixed outputs
• Two additional digital inputs, two additional digital outputs
• External reset input
• Alternate I/O bus can be configured for 8 data lines and 6 address lines (shared with
parallel I/O lines), I/O read/write
• Ten 8-bit timers (six cascadable) and one 10-bit timer with two match registers
• 512K flash memory, 512K program execution SRAM, 256K data SRAM
• Real-time clock
• Watchdog supervisor
• Provision for customer-supplied backup battery via connections on header J2
User’s Manual
1
• 10/100Base-T RJ-45 Ethernet port
• 10-bit free-running PWM counter and four width registers
• Two-channel Input Capture can be used to time input signals from various port pins
• Two-channel Quadrature Decoder accepts inputs from external incremental encoder
modules
• Six CMOS-compatible serial ports: maximum asynchronous baud rate of 5.5 Mbps. Four
ports are configurable as a clocked serial port (SPI), and two ports are configurable as
SDLC/HDLC serial ports.
• Supports 1.15 Mbps IrDA transceiver
Appendix A, “RCM3200 Specifications,” provides detailed specifications for the
RCM3200.
1.2 Advantages of the RCM3200
• Fast time to market using a fully engineered, “ready to run” microprocessor core.
• Competitive pricing when compared with the alternative of purchasing and assembling
individual components.
• Easy C-language program development and debugging
• Program Download Utility and cloning board options for rapid production loading of
programs.
• Generous memory size allows large programs with tens of thousands of lines of code,
and substantial data storage.
• Integrated Ethernet port for network connectivity, royalty-free TCP/IP software.
1.3 Development and Evaluation Tools
A complete Development Kit, including a Prototyping Board and Dynamic C development software, is available for the RCM3200. The Development Kit puts together the
essentials you need to design an embedded microprocessor-based system rapidly and efficiently.
See the RabbitCore RCM3200 Getting Started Manual for complete information on the
Development Kit.
2
RabbitCore RCM3200
1.4 How to Use This Manual
This user’s manual is intended to give users detailed information on the RCM3200 module. It does not contain detailed information on the Dynamic C development environment
or the TCP/IP software support for the integrated Ethernet port. Most users will want more
detailed information on some or all of these topics in order to put the RCM3200 module to
effective use.
1.4.1 Additional Product Information
Introductory information about the RCM3200 and its associated Development Kit and
Prototyping Board will be found in the printed RabbitCore RCM3200 Getting Started
Manual, which is also provided on the accompanying CD-ROM in both HTML and
Adobe PDF format.
We recommend that any users unfamiliar with Z-World products, or those who will be
using the Prototyping Board for initial evaluation and development, begin with at least a
read-through of the Getting Started manual.
In addition to the product-specific information contained in the RabbitCore RCM3200
Getting Started Manual and the RabbitCore RCM3200 User’s Manual (this manual),
several higher level reference manuals are provided in HTML and PDF form on the
accompanying CD-ROM. Advanced users will find these references valuable in developing systems based on the RCM3200 modules:
• Dynamic C User’s Manual
• Dynamic C Function Reference Manual
• An Introduction to TCP/IP
• Dynamic C TCP/IP User’s Manual
• Rabbit 3000 Microprocessor User’s Manual
1.4.2 Online Documentation
The online documentation is installed along with Dynamic C, and an icon for the documentation menu is placed on the workstation’s desktop. Double-click this icon to reach the
menu. If the icon is missing, use your browser to find and load default.htm in the docs
folder, found in the Dynamic C installation folder.
The latest versions of all documents are always available for free, unregistered download
from our Web sites as well.
User’s Manual
3
4
RabbitCore RCM3200
2. HARDWARE REFERENCE
Chapter 2 describes the hardware components and principal hardware
subsystems of the RCM3200. Appendix A, “RCM3200 Specifications,” provides complete physical and electrical specifications.
Figure 1 shows these Rabbit-based subsystems designed into the RCM3200.
32 kHz
osc
SRAM
Flash
22.1 MHz
osc
RABBIT
3000
logic-level serial signal
Level
converter
Ethernet
RabbitCore Module
RS-232, RS-485, IRDA
serial communication
drivers on motherboard
Figure 1. RCM3200 Subsystems
User’s Manual
5
2.1 RCM3200 Digital Inputs and Outputs
The RCM3200 has 52 parallel I/O lines grouped in seven 8-bit ports available on headers
J1 and J2. The 44 bidirectional I/O lines are located on pins PA0–PA7, PB0, PB2–PB7,
PD2–PD7, PE0–PE1, PE3–PE7, PF0–PF7, and PG0–PG7.
Figure 2 shows the RCM3200 pinouts for headers J1 and J2.
J1
GND
PA7
PA5
PA3
PA1
PF3
PF1
PC0
PC2
PC4
PC6-TxA
PG0
PG2
PD4
PD2
PD6
n.c.
J2
STATUS
PA6
PA4
PA2
PA0
PF2
PF0
PC1
PC3
PC5
PC7-RxA
PG1
PG3
PD5
PD3
PD7
n.c.
/RES
PB2
PB4
PB6
PF4
PF6
PE7
PE5
PE3
PE0
PG6
PG4
/IORD
SMOD1
VRAM
+3.3V
n.c.
PB0
PB3
PB5
PB7
PF5
PF7
PE6
PE4
PE1
PG7
PG5
/IOWR
SMOD0
/RESET_IN
VBAT_EXT
GND
GND
n.c. = not connected
Note: These pinouts are as seen on
the Bottom Side of the module.
Figure 2. RCM3200 Pinouts
The pinouts for the RCM3000, RCM3100, and RCM3200 are compatible. Visit the Web site for
further information.
Headers J1 and J2 are standard 2 × 34 headers with a nominal 2 mm pitch. An RJ-45 Ethernet jack is also included with the RCM3200 series.
The signals labeled PD2, PD3, PD6, and PD7 on header J1 (pins 29–32) and the pins that
are not connected (pins 33–34 on header J1 and pin 33 on header J2) are reserved for
future use.
6
RabbitCore RCM3200
Figure 3 shows the use of the Rabbit 3000 microprocessor ports in the RCM3200 modules.
PC0, PC2, PC4
PC1, PC3, PC5
PG2, PG6
PG3, PG7
PC6
PB1, PC7, /RES
4 Ethernet signals
PA0–PA7
PB0,
PB2–PB7
PD4–PD5
Port A
Port B
(+Ethernet Port)
Port C
(Serial Ports B,C & D)
Port G
Port D
RABBIT
3000
(Serial Ports E & F)
Programming
Port
(Serial Port A)
Ethernet
Port
RAM
Real-Time Clock
Watchdog
11 Timers
Slave Port
Clock Doubler
Port E
PE0–PE1,
PE3–PE7
Port F
PF0–PF7
Port G
PG0–PG1,
PG4–PG5
/RES_IN
/IORD
/RESET,
/IOWR,
STATUS
SMODE0
SMODE1
(+Serial Ports)
Misc. I/O
Backup Battery
Support
Flash
Figure 3. Use of Rabbit 3000 Ports
The ports on the Rabbit 3000 microprocessor used in the RCM3200 are configurable, and
so the factory defaults can be reconfigured. Table 1 lists the Rabbit 3000 factory defaults
and the alternate configurations.
User’s Manual
7
Table 1. RCM3200 Pinout Configurations
Pin
Pin Name
1
GND
2
STATUS
Default Use
Alternate Use
Output (Status)
Output
Notes
3–10
PA[7:0]
Parallel I/O
External data bus
(ID0–ID7)
Slave port data bus
(SD0–SD7)
11
PF3
Input/Output
QD2A
12
PF2
Input/Output
QD2B
13
PF1
Input/Output
QD1A
CLKC
14
PF0
Input/Output
QD1B
CLKD
15
PC0
Output
TXD
16
PC1
Input
RXD
17
PC2
Output
TXC
18
PC3
Input
RXC
19
PC4
Output
TXB
20
PC5
Input
RXB
21
PC6
Output
TXA
22
PC7
Input
RXA
Serial Port A
(programming port)
23
PG0
Input/Output
TCLKF
Serial Clock F output
24
PG1
Input/Output
RCLKF
Serial Clock F input
25
PG2
Input/Output
TXF
26
PG3
Input/Output
RXF
27
PD4
Input/Output
ATXB
28
PD5
Input/Output
ARXB
29
PD2
Input/Output
TPOUT– *
30
PD3
Input/Output
TPOUT+ *
31
PD6
Input/Output
TPIN– *
32
PD7
Input/Output
TPIN+ *
33
LNK_OUT
Output
34
ACT_OUT
Output
Serial Port D
Header J1
Serial Port C
Serial Port B
Serial Port F
Ethernet transmit port
Ethernet receive port
*
8
Max. current draw 1 mA
(see Note 1)
Pins 29–32 are reserved for future use.
RabbitCore RCM3200
Table 1. RCM3200 Pinout Configurations (continued)
Header J2
Pin
Pin Name
Default Use
Alternate Use
Notes
Reset output from Reset
Generator
1
/RES
Reset output
Reset input
2
PB0
Input/Output
CLKB
3
PB2
Input/Output
IA0
/SWR
External Address 0
Slave port write
4
PB3
Input/Output
IA1
/SRD
External Address 1
Slave port read
5
PB4
Input/Output
IA2
SA0
External Address 2
Slave port Address 0
6
PB5
Input/Output
IA3
SA1
External Address 3
Slave port Address 1
7
PB6
Input/Output
IA4
External Address 4
8
PB7
Input/Output
IA5
/SLAVEATTN
External Address 5
Slave Attention
9
PF4
Input/Output
AQD1B
PWM0
10
PF5
Input/Output
AQD1A
PWM1
11
PF6
Input/Output
AQD2B
PWM2
12
PF7
Input/Output
AQD2A
PWM3
13
PE7
Input/Output
I7
/SCS
14
PE6
Input/Output
I6
15
PE5
Input/Output
I5
INT1B
16
PE4
Input/Output
I4
INT0B
17
PE3
Input/Output
I3
18
PE1
Input/Output
I1
INT1A
I/O Strobe 1
Interrupt 1A
19
PE0
Input/Output
I0
INT0A
I/O Strobe 0
Interrupt 0A
User’s Manual
9
Table 1. RCM3200 Pinout Configurations (continued)
Pin
Pin Name
Default Use
Alternate Use
Notes
20
PG7
Input/Output
RXE
21
PG6
Input/Output
TXE
22
PG5
Input/Output
RCLKE
Serial Clock E input
23
PG4
Input/Output
TCLKE
Serial Clock E ouput
24
/IOWR
Output
External write strobe
25
/IORD
Input
External read strobe
Header J2
Serial Port E
26–27
SMODE0,
SMODE1
(0,0)—start executing at address zero
(0,1)—cold boot from slave port
(1,0)—cold boot from clocked Serial Port A
Also connected to
programming cable
SMODE0 =1, SMODE1 = 1
Cold boot from asynchronous Serial Port A at
2400 bps (programming cable connected)
28
/RESET_IN
Input
Input to Reset Generator
29
VRAM
Output
See Notes below table
30
VBAT_EXT
3 V battery Input
Minimum battery
voltage 2.85 V
31
+3.3V
Input
3.15–3.45 V DC
32
GND
33
n.c.
34
GND
Reserved for future use
Notes
1. When using pins 33–34 on header J1 to drive LEDs, you must use an external buffer to
drive these external LEDs. These pins are not connected on the RCM3220, which does
not have the LEDs installed.
2. The VRAM voltage is temperature-dependent. If the VRAM voltage drops below about
1.2 V to 1.5 V, the contents of the battery-backed SRAM may be lost. If VRAM drops
below 1.0 V, the 32 kHz oscillator could stop running. Pay careful attention to this voltage if you draw any current from this pin.
Locations R45, R46, R53, R57, and R74 allow the population of 0 Ω resistors (jumpers)
that will be used to enable future options. These locations are currently unused.
10
RabbitCore RCM3200
2.1.1 Memory I/O Interface
The Rabbit 3000 address lines (A0–A19) and all the data lines (D0–D7) are routed internally to the onboard flash memory and SRAM chips. I/0 write (/IOWR) and I/0 read
(/IORD) are available for interfacing to external devices.
Parallel Port A can also be used as an external I/O data bus to isolate external I/O from the
main data bus. Parallel Port B pins PB2–PB7 can also be used as an auxiliary address bus.
When using the auxiliary I/O bus, you must add the following line at the beginning of
your program.
#define PORTA_AUX_IO
// required to enable auxiliary I/O bus
The STATUS output has three different programmable functions:
3. It can be driven low on the first op code fetch cycle.
4. It can be driven low during an interrupt acknowledge cycle.
5. It can also serve as a general-purpose output.
2.1.2 Other Inputs and Outputs
Two status mode pins, SMODE0 and SMODE1, are available as inputs. The logic state of
these two pins determines the startup procedure after a reset.
/RESET_IN is an external input used to reset the Rabbit 3000 microprocessor and the
RCM3200 memory. /RES is an output from the reset circuitry that can be used to reset
other peripheral devices.
User’s Manual
11
2.2 Serial Communication
The RCM3200 board does not have an RS-232 or an RS-485 transceiver directly on the
board. However, an RS-232 or RS-485 interface may be incorporated on the board the
RCM3200 is mounted on. For example, the Prototyping Board has a standard RS-232
transceiver chip.
2.2.1 Serial Ports
There are six serial ports designated as Serial Ports A, B, C, D, E, and F. All six serial
ports can operate in an asynchronous mode up to the baud rate of the system clock divided
by 8. An asynchronous port can handle 7 or 8 data bits. A 9th bit address scheme, where
an additional bit is sent to mark the first byte of a message, is also supported. Serial Ports
A, B, C, and D can also be operated in the clocked serial mode. In this mode, a clock line
synchronously clocks the data in or out. Either of the two communicating devices can supply the clock.
Serial Ports E and F can also be configured as SDLC/HDLC serial ports. The IrDA protocol is also supported in SDLC format by these two ports.
2.2.2 Ethernet Port
Figure 4 shows the pinout for the RJ-45 Ethernet port (J4). Note that some Ethernet connectors are numbered in reverse to the order used here.
ETHERNET
1
8
1.
2.
3.
6.
RJ-45 Plug
E_Tx+
E_Tx–
E_Rx+
E_Rx–
RJ-45 Jack
Figure 4. RJ-45 Ethernet Port Pinout
Three LEDs are placed next to the RJ-45 Ethernet
jack, one to indicate an Ethernet link (LNK), one to
indicate Ethernet activity (ACT), and one to indicate when the RCM3200 is connected to a functioning 100Base-T network (SPD).
The transformer/connector assembly ground is connected to the RCM3200 printed circuit board digital
ground via a 0 Ω resistor, R42, as shown in Figure 5.
The RJ-45 connector is shielded to minimize EMI
effects to/from the Ethernet signals.
12
RJ-45 Ethernet Plug
R42
Board
Ground
Chassis
Ground
Figure 5. Isolation Resistor R42
RabbitCore RCM3200
2.2.3 Programming Port
Serial Port A has special features that allow it to cold-boot the system after reset. Serial
Port A is also the port that is used for software development under Dynamic C.
The RCM3200 has a 10-pin program header labeled J3. The Rabbit 3000 startup-mode
pins (SMODE0, SMODE1) are presented to the programming port so that an externally
connected device can force the RCM3200 to start up in an external bootstrap mode. The
Rabbit 3000 Microprocessor User’s Manual provides more information related to the
bootstrap mode.
The programming port is used to start the RCM3200 in a mode where it will download a
program from the port and then execute the program. The programming port transmits
information to and from a PC while a program is being debugged in-circuit.
The RCM3200 can be reset from the programming port via the /RESET_IN line.
The Rabbit 3000 status pin is also presented to the programming port. The status pin is an
output that can be used to send a general digital signal.
The clock line for Serial Port A is presented to the programming port, which makes synchronous serial communication possible.
Programming may also be initiated through the motherboard to which the RCM3200
series module is plugged in to since the Serial Port A (PC6 and PC7), SMODE0, SMODE1,
and /RESET_IN are available on headers J1 and J2 (see Table 1).
2.2.3.1 Alternate Uses of the Programming Port
The programming port may also be used as an application port with the DIAG connector
on the programming cable.
All three clocked Serial Port A signals are available as
• a synchronous serial port
• an asynchronous serial port, with the clock line usable as a general CMOS input
• two general CMOS inputs and one general CMOS output.
Two startup mode pins, SMODE0 and SMODE1, are available as general CMOS inputs
after they are read during the initial boot-up. The logic state of these two pins is very
important in determining the startup procedure after a reset.
/RES_IN is an external input used to reset the Rabbit 3000 microprocessor.
The status pin may also be used as a general CMOS output.
See Appendix E, “Programming Cable,” for more information.
User’s Manual
13
2.3 Programming Cable
The RCM3200 is automatically in program mode when the PROG connector on the programming cable is attached, and is automatically in run mode when no programming cable
is attached.
The DIAG connector of the programming cable may be used on header J3 of the RCM3200
with the board operating in the run mode. This allows the programming port to be used as
an application port. See Appendix E, “Programming Cable,” for more information.
MOTOR/ENCODER
J6
C11 C10
MASTER
C72
RESET
C16
C15
C6
RxC TxC
J5
J4
TxB RxB
RESET
GND
C19
GND
C32
U6
C16
BA3
BA1
BD0
BD2
BD4
BD6
BD1
BD3
BD5
BD7
DISPLAY BOARD
RC25
RC4
RC5
C14
RC27
U3
U3
RC28
RC29
RC26
To
PC COM port
UX5
R14
RC9
UX7
PG6
PG7
C7
RS-232
+5V
C9
R24
S3
+5V
UX4
Programming Cable
J13
S2
RC7
GND
C45
C44
C43
R38
C39
RC6
GND
+3.3V
+5V
+5V
J8
BA0
C48
JP3
JP4
C28
C27
C24
C20
C1
C5
C8
J12
R28
JP5
R31
GND
C37
C36
PA7
PE4
R27
PA5
PA6
/RES
C9
C8
PA3
PA4
PB2
PB0
U1
C4
PA2
PB4
PB3
R42
PB6
PB5
C35
PB7
C29
PA1
C17
PF3
PA0
C33
PF1
PF2
PF4
C30
PF0
PF6
PF5
C23
PE7
PF7
C18
PE6
C12
PC0
C4
PC2
PC1
C3
PC4
PC3
PE5
U1 C5
PC5
PE3
PE4
R10
R14
PE0
PE1
R8
PG7
+3.3V
R1
PD5
R7
R9
PD4
RP1
PG6
R17
R18
PG5
R19
PG0
R20
PG1
R23
PG4
GND
GND
+3.3V
+3.3V
R22
/IOWR
R25
PG2
U4
PD4
PG3
C31
PD2
PD5
/IORD
GND
GND
D1
PD3
SM1
R29
R37
R39
R40
VRAM
SM0
Y3
VBAT
EXT
/RES
IN
C42
PD6
R35
PD7
U5
+3.3V
U6
GND
GND
C49
UX2
BA2
R51
R49
R48
C61
RC2
Q1
PD0
R41
PD1
C53
NC
C47
GND
GND
R72
C75
RC1
R74
C64
C67
R9
RC11
C57
R67
R70
C83
C71
L2
C62
RC21
R11
RC10
R13
R21
RC22
R7
UX3
L1
DS3
DS2
DS1
RC16
RC12
R12
R6
RC14
RC17
RC13
RC24
RC23
C68
GND
R71
UX9
RCM3000
RABBITCORE
RCM2
R75
RC20
R8
R2
RC19
R10
C3
R5
SPD LNK ACT
R4
UX11
R58
RC15
C2
R1
R3
J15
SLAVE
UX10
GND
C1
+3.3V
/RES
LCD
J14
PA7
J3
J4
PE4
C79
Y4
PA6
/RES
R63 R64
PB2
RN2
J1
C86
PB0
+3.3V
BT1
R69
PB3
Battery
RCM3000 RABBITCORE
RCM1
+5V
PA5
+5V
PA4
BPE3
PB4
DS1
DS2
DIAG
PA3
PB5
+DC
GND
PA1
PA2
R16
PF3
PA0
PB6
PROG
PF2
PF4
GND
+5V
PF6
PF5
+5V
C74
PF1
PF7
PB7
+5V
+5V
PE7
PF0
C12
U5
TP1
PE6
2.5 MM JACK
D2
U4
R15
PC0
RC18
PC1
R47
PE5
R44
PC2
PE4
J3
PC4
PC3
C59
PD5
PC5
PE3
U8
PG0
PD4
PE0
PE1
J11
D1
C13
R20
R17
R73
PG1
PG6
PG7
C17
JP1
PG4
PG5
CURRENT
MEASUREMENT
OPTION
/IOWR
L1
DS3
PG2
+3.3V
POWER
PD4
PG3
C15
PD2
PD5
/IORD
VRAM
RN4
PD3
SM1
SM0
RN5
POWER
VBAT
EXT
/RES
IN
GND
J9
PD6
+DC
PD7
GND
PD0
+3.3V
GND
PD1
GND
RN3
NC
+5V
+3.3V
RN1
GND
RCM3000 PROTOTYPING BOARD
J10
UX13
J7
Colored edge
DISPLAY BOARD
DISPLAY BOARD
RESET RCM3200 when changing mode:
Short out pins 28–32 on header J2, OR
Press RESET button (if using Prototyping Board), OR
Remove, then reapply power
after removing or attaching programming cable.
Figure 6. Switching Between Program Mode and Run Mode
2.3.1 Changing from Program Mode to Run Mode
1. Disconnect the programming cable from header J3 of the RCM3200.
2. Reset the RCM3200. You may do this as explained in Figure 6.
The RCM3200 is now ready to operate in the run mode.
2.3.2 Changing from Run Mode to Program Mode
1. Attach the programming cable to header J3 on the RCM3200.
2. Reset the RCM3200. You may do this as explained in Figure 6.
The RCM3200 is now ready to operate in the program mode.
14
RabbitCore RCM3200
2.4 Other Hardware
2.4.1 Clock Doubler
The RCM3200 takes advantage of the Rabbit 3000 microprocessor’s internal clock doubler. A built-in clock doubler allows half-frequency crystals to be used to reduce radiated
emissions. The 44.2 MHz frequency specified for the RCM3200 is generated using a
22.12 MHz resonator.
The clock doubler may be disabled if 44.2 MHz clock speeds are not required. Disabling
the Rabbit 3000 microprocessor’s internal clock doubler will reduce power consumption
and further reduce radiated emissions. The clock doubler is disabled with a simple change
to the BIOS as described below.
1. Open the BIOS source code file, RABBITBIOS.C in the BIOS directory.
2. Change the line
#define CLOCK_DOUBLED 1 //
//
//
//
set to 1 to double clock if
Rabbit 2000: crystal <= 12.9024 MHz,
Rabbit 3000: crystal <= 26.7264 MHz,
or to 0 to always disable clock doubler
to read as follows.
#define CLOCK_DOUBLED 0
3. Save the change using File > Save.
2.4.2 Spectrum Spreader
The Rabbit 3000 features a spectrum spreader, which helps to mitigate EMI problems. By
default, the spectrum spreader is on automatically, but it may also be turned off or set to a
stronger setting. The means for doing so is through a simple change to the following BIOS
line in a way that is similar to the clock doubler described above.
#define ENABLE_SPREADER 1
// Set to 0 to disable spectrum spreader.
#define SPREADER_SETTING 0 // 0 = normal spreading, 1 = strong spreading
NOTE: Refer to the Rabbit 3000 Microprocessor User’s Manual for more information
on the spectrum-spreading setting and the maximum clock speed.
User’s Manual
15
2.5 Memory
2.5.1 SRAM
The RCM3200 has 512K of program execution SRAM installed at U8 and packaged in a
32-pin TSOP or sTSOP case. The data SRAM installed at U6 is 256K.
2.5.2 Flash EPROM
The RCM3200 is also designed to accept 256K to 512K of flash EPROM packaged in a
32-pin TSOP or sTSOP case. The flash EPROM installed at U7 is 512K
NOTE: Z-World recommends that any customer applications should not be constrained
by the sector size of the flash EPROM since it may be necessary to change the sector
size in the future.
Writing to arbitrary flash memory addresses at run time is also discouraged. Instead,
define a “user block” area to store persistent data. The functions writeUserBlock and
readUserBlock are provided for this.
A Flash Memory Bank Select jumper configuration option based on 0 Ω surface-mounted
resistors exists at header JP4 on the RCM3200 RabbitCore modules. This option, used in
conjunction with some configuration macros, allows Dynamic C to compile two different
co-resident programs for the upper and lower halves of the 512K flash in such a way that
both programs start at logical address 0000. This is useful for applications that require a
resident download manager and a separate downloaded program. See Technical Note
TN218, Implementing a Serial Download Manager for a 256K Flash, for details.
2.5.3 Dynamic C BIOS Source Files
The Dynamic C BIOS source files handle different standard RAM and flash EPROM sizes
automatically.
16
RabbitCore RCM3200
3. SOFTWARE REFERENCE
Dynamic C is an integrated development system for writing
embedded software. It runs on an IBM-compatible PC and is
designed for use with Z-World controllers and other controllers
based on the Rabbit microprocessor. Chapter 3 provides the
libraries, function calls, and sample programs related to the
RCM3200.
3.1 More About Dynamic C
Dynamic C has been in use worldwide since 1989. It is specially designed for programming embedded systems, and features quick compile and interactive debugging in the real
environment. A complete reference guide to Dynamic C is contained in the Dynamic C
User’s Manual.
You have a choice of doing your software development in the flash memory or in the data
SRAM included on the RCM3200. The advantage of working in RAM is to save wear on
the flash memory, which is limited to about 100,000 write cycles. The disadvantage is that
the code and data might not both fit in RAM.
NOTE: An application can be developed in the data SRAM, but should be run from the
program execution SRAM after the programming cable is disconnected. To run the
application in the fast program execution SRAM, select Code and BIOS in Flash,
Run in RAM from the Dynamic C Options > Compiler menu.
NOTE: Do not depend on the flash memory sector size or type. Due to the volatility of
the flash memory market, the RCM3200 and Dynamic C were designed to accommodate flash devices with various sector sizes.
The disadvantage of using flash memory for debug is that interrupts must be disabled for
approximately 5 ms whenever a break point is set in the program. This can crash fast interrupt routines that are running while you stop at a break point or single-step the program.
The flash memory and SRAM options are selected with the Options > Compiler menu.
Dynamic C provides a number of debugging features. You can single-step your program,
either in C, statement by statement, or in assembly language, instruction by instruction.
You can set break points, where the program will stop, on any statement. You can evaluate
watch expressions. A watch expression is any C expression that can be evaluated in the
context of the program. If the program is at a break point, a watch expression can view any
expression using local or global variables. If a periodic call to runwatch() is included in
your program, you will be able to evaluate watch expressions by hitting <Ctrl-U> without
stopping the program.
User’s Manual
17
3.2 Dynamic C Functions
The functions described in this section are for use with the Prototyping Board features.
The source code is in the RCM32xx.LIB library in the Dynamic C SAMPLES\RCM3200
folder if you need to modify it for your own board design.
Other generic functions applicable to all devices based on Rabbit microprocessors are
described in the Dynamic C Function Reference Manual.
3.2.1 Board Initialization
void brdInit (void);
Call this function at the beginning of your program. This function initializes Parallel Ports A through G
for use with the RCM3200 Prototyping Board.
Summary of Initialization
1. I/O port pins are configured for Prototyping Board operation.
2. Unused configurable I/O are set as high outputs.
3. Only one RabbitCore module is plugged in, and is in the MASTER position on the Prototyping
Board.
3. The LCD/keypad module is disabled.
4. RS-485 is not enabled.
5. RS-232 is not enabled.
6. The IrDA transceiver is disabled.
7. LEDs are off.
RETURN VALUE
None.
18
RabbitCore RCM3200
3.2.2 Digital I/O
The RCM3200 was designed to interface with other systems, and so there are no drivers
written specifically for the I/O. The general Dynamic C read and write functions allow
you to customize the parallel I/O to meet your specific needs. For example, use
WrPortI(PEDDR, &PEDDRShadow, 0x00);
to set all the Port E bits as inputs, or use
WrPortI(PEDDR, &PEDDRShadow, 0xFF);
to set all the Port E bits as outputs.
When using the auxiliary I/O bus on the Rabbit 3000 chip, add the line
#define PORTA_AUX_IO
// required to enable auxiliary I/O bus
to the beginning of any programs using the auxiliary I/O bus.
The sample programs in the Dynamic C SAMPLES/RCM3200 directory provide further
examples.
3.2.3 Serial Communication Drivers
Library files included with Dynamic C provide a full range of serial communications support. The RS232.LIB library provides a set of circular-buffer-based serial functions. The
PACKET.LIB library provides packet-based serial functions where packets can be delimited by the 9th bit, by transmission gaps, or with user-defined special characters. Both
libraries provide blocking functions, which do not return until they are finished transmitting or receiving, and nonblocking functions, which must be called repeatedly until they
are finished. For more information, see the Dynamic C Function Reference Manual and
Technical Note 213, Rabbit 2000 Serial Port Software.
3.2.4 TCP/IP Drivers
The TCP/IP drivers are located in the TCPIP directory.
Complete information on these libraries and the TCP/IP functions is provided in the
Dynamic C TCP/IP User’s Manual.
User’s Manual
19
3.3 Sample Programs
Sample programs are provided in the Dynamic C Samples folder.
Two subdirectories contain sample programs that illustrate features unique to the
RCM3200.
• RCM3200—Demonstrates the basic operation and the Ethernet functionality of the
RCM3200.
• TCPIP—Demonstrates more advanced TCP/IP programming for Z-World’s Ethernetenabled Rabbit-based boards.
Follow the instructions included with the sample program to connect the RCM3200 and
the other hardware identified in the instructions.
Before running any Dynamic C applications, you will need to allow the compiler to run
the application in the fast program execution SRAM by selecting Code and BIOS in
Flash, Run in RAM from the Compiler tab in the Dynamic C Options > Project Options
menu.
To run a sample program, open it with the File menu (if it is not still open), compile it
using the Compile menu (or press F5), and then run it by selecting Run in the Run menu
(or press F9). The RCM3200 must be in Program Mode (see Figure 6) and must be connected to a PC using the programming cable.
More complete information on Dynamic C is provided in the Dynamic C User’s Manual.
20
RabbitCore RCM3200
3.4 Upgrading Dynamic C
Dynamic C patches that focus on bug fixes are available from time to time. Check the Web
sites
• www.zworld.com/support/
or
• www.rabbitsemiconductor.com/support/
for the latest patches, workarounds, and bug fixes.
3.4.1 Add-On Modules
Dynamic C installations are designed for use with the board they are included with, and
are included at no charge as part of our low-cost kits. Z-World offers add-on Dynamic C
modules for purchase, including the popular µC/OS-II real-time operating system, as well
as PPP, Advanced Encryption Standard (AES), and other select libraries.
In addition to the Web-based technical support included at no extra charge, a one-year
telephone-based technical support module is also available for purchase.
User’s Manual
21
22
RabbitCore RCM3200
APPENDIX A. RCM3200 SPECIFICATIONS
Appendix A provides the specifications for the RCM3200, and
describes the conformal coating.
User’s Manual
23
A.1 Electrical and Mechanical Characteristics
Figure A-1 shows the mechanical dimensions for the RCM3200.
1.850
(47.0)
1.375
(34.9)
R8
C18
C30
C33
C35
C37
C36
R27
R29
R37
R39
C42
C45
C44
C43
R38
Y3
(69.2)
R35
2.725
R31
JP5
R28
C39
R25
U5
U6
R40
Q1
R41
R42
C48
C49
C57
C61
L1
C62
L2
C68
R58
C64
C67
R74
C83
R72
R73
DS1
R71
R75
C86
DS2
DS3
GND
0.67
1.18
(17.0)
0.15
(3.8)
J1
(22)
0.86
(22)
0.86
(6.5)
(47.0)
0.256
1.850
(2)
J2
0.08
(14)
0.55
(69.2)
(6.5)
2.725
0.256
(2.5)
0.10
(14)
0.55
(30.0)
(12.7)
J4
SPD LNK ACT
C79
Y4
R67
R70
R69
0.50
R63 R64
C75
C74
C72
C71
(33.5)
C59
R51
R49
R48
R47
R44
U8
(15.7)
C53
0.625
C47
RP1
C23
C29
C28
C27
JP3
D1
JP4
C31
Please refer to the RCM3200
footprint diagram later in this
appendix for precise header
locations.
C12
C17
C24
C20
C19
U4
C32
(2.5)
R24
0.100 dia
R20
R23
C16
C15
R19
R22
C4
U1 C5
R17
R18
J3
C9
C8
C1
C3
R10
R14
1.320
R1
R7
R9
Figure A-1. RCM3200 Dimensions
24
RabbitCore RCM3200
It is recommended that you allow for an “exclusion zone” of 0.04" (1 mm) around the
RCM3200 in all directions (except above the RJ-45 plug) when the RCM3200 is incorporated into an assembly that includes other printed circuit boards. This “exclusion zone”
that you keep free of other components and boards will allow for sufficient air flow, and
will help to minimize any electrical or electromagnetic interference between adjacent
boards. An “exclusion zone” of 0.08" (2 mm) is recommended below the RCM3200
when the RCM3200 is plugged into another assembly using the shortest connectors for
headers J1 and J2. Figure A-2 shows this “exclusion zone.”
2.81
(2)
0.08
0.6
(16)
(71.2)
2.725
(69.2)
1.93
(49.0)
(2)
0.08
0.6
(16)
Exclusion
Zone
J2
1.850
J1
(47.0)
Figure A-2. RCM3200 “Exclusion Zone”
User’s Manual
25
Table A-1 lists the electrical, mechanical, and environmental specifications for the RCM3200.
Table A-1. RabbitCore RCM3200 Specifications
Feature
Microprocessor
RCM3200
RCM3210
RCM3220
Rabbit 3000® at
44.2 MHz
Rabbit 3000® at
29.5 MHz
Rabbit 3000® at
44.2 MHz
EMI Reduction
Spectrum spreader for reduced EMI (radiated emissions)
Ethernet Port
10/100Base-T, RJ-45, 3 LEDs
—
Flash Memory
512K
256K
512K
Data SRAM
256K
128K
256K
Program Execution SRAM
512K
—
512K
Backup Battery
Connection for user-supplied backup battery
(to support RTC and data SRAM)
General-Purpose I/O
52 parallel digital I/0 lines:
• 44 configurable I/O
• 4 fixed inputs
• 4 fixed outputs
Additional Inputs
Startup mode (2), reset in
Additional Outputs
Status, reset out
Auxiliary I/O Bus
Can be configured for 8 data lines and
6 address lines (shared with parallel I/O lines), plus I/O read/write
6 shared high-speed, CMOS-compatible ports:
• all 6 configurable as asynchronous (with IrDA), 4 as clocked serial (SPI),
Serial Ports
and 2 as SDLC/HDLC (with IrDA)
• 1 asynchronous serial port dedicated for programming
• support for MIR/SIR IrDA transceiver
Serial Rate
Slave Interface
Real-Time Clock
Timers
Watchdog/Supervisor
Pulse-Width Modulators
Maximum asynchronous baud rate = CLK/8
A slave port allows the RCM3200 to be used as an intelligent peripheral
device slaved to a master processor, which may either be another Rabbit
3000 or any other type of processor
Yes
Ten 8-bit timers (6 cascadable), one 10-bit timer with 2 match registers
Yes
10-bit free-running counter and four pulse-width registers
Input Capture
2- channel input capture can be used to time input signals from various port
pins
Quadrature Decoder
2-channel quadrature decoder accepts inputs from external incremental
encoder modules
Power
26
3.15 V to 3.45 V DC
255 mA @ 3.3 V
RabbitCore RCM3200
Table A-1. RabbitCore RCM3200 Specifications (continued)
Feature
RCM3200
Operating Temperature
RCM3210
RCM3220
–40°C to +70°C
Humidity
5% to 95%, noncondensing
Connectors
Two 2 × 17, 2 mm pitch
Board Size
1.850" × 2.725" × 0.86"
(47 mm × 69 mm × 22 mm)
A.1.1 Headers
The RCM3200 uses headers at J1 and J2 for physical connection to other boards. J1 and J2
are 2 × 17 SMT headers with a 2 mm pin spacing. J3, the programming port, is a 2 × 5
header with a 1.27 mm pin spacing.
Figure A-3 shows the layout of another board for the RCM3200 to be plugged into. These
values are relative to the mounting hole.
A.1.2 Physical Mounting
A 9/32” (7 mm) standoff with a 2-56 screw is recommended to attach the RCM3200 to a
user board at the hole position shown in Figure A-3. Either use plastic hardware, or use
insulating washers to keep any metal hardware from shorting out signals on the RCM3200.
J3
J2
1.124
RCM3000 Footprint
(28.5)
1.341
1.198
(34.1)
1.136
(30.4)
(28.9)
0.100 dia
(2.5)
0.020 sq typ
(0.5)
0.079
0.332
(8.4)
0.314
(8.0)
(2.0)
0.079
(2.0)
J1
0.953
(24.2)
1.043
(26.5)
1.131
(28.7)
Figure A-3. User Board Footprint for RCM3200
User’s Manual
27
A.2 Bus Loading
You must pay careful attention to bus loading when designing an interface to the
RCM3200. This section provides bus loading information for external devices.
Table A-2 lists the capacitance for the various RCM3200 I/O ports.
Table A-2. Capacitance of Rabbit 3000 I/O Ports
I/O Ports
Input
Capacitance
(pF)
Output
Capacitance
(pF)
12
14
Parallel Ports A to G
Table A-3 lists the external capacitive bus loading for the various RCM3200 output ports.
Be sure to add the loads for the devices you are using in your custom system and verify
that they do not exceed the values in Table A-3.
Table A-3. External Capacitive Bus Loading -40°C to +70°C
Clock Speed
(MHz)
Maximum External
Capacitive Loading (pF)
All I/O lines with clock
doubler enabled
29.4
30–70
All I/O lines with clock
doubler disabled
14.7456
100
Output Port
28
RabbitCore RCM3200
Figure A-4 shows a typical timing diagram for the Rabbit 3000 microprocessor external
memory read and write cycles.
External I/O Read (no extra wait states)
T1
Tw
T2
CLK
A[15:0]
valid
Tadr
/CSx
/IOCSx
TCSx
TCSx
TIOCSx
TIOCSx
/IORD
TIORD
TIORD
/BUFEN
TBUFEN
Tsetup
TBUFEN
D[7:0]
valid
Thold
External I/O Write (no extra wait states)
T1
Tw
T2
CLK
A[15:0]
valid
Tadr
/CSx
/IOCSx
/IOWR
/BUFEN
D[7:0]
TCSx
TCSx
TIOCSx
TIOCSx
TIOWR
TIOWR
TBUFEN
TBUFEN
valid
TDHZV
TDVHZ
Figure A-4. I/O Read and Write Cycles—No Extra Wait States
NOTE: /IOCSx can be programmed to be active low (default) or active high.
User’s Manual
29
Table A-4 lists the delays in gross memory access time for several values of VDD.
Table A-4. Data and Clock Delays VDD ±10%, Temp, -40°C–+85°C (maximum)
Clock to Address Output Delay
(ns)
30 pF
60 pF
90 pF
Data Setup
Time Delay
(ns)
3.3
6
8
11
2.7
7
10
2.5
8
1.8
18
VDD
Spectrum Spreader Delay
(ns)
Normal
Strong
dbl/no dbl
dbl/no dbl
1
3/4.5
4.5/9
13
1.5
3.5/5.5
5.5/11
11
15
1.5
4/6
6/12
24
33
3
8/12
11/22
The measurements are taken at the 50% points under the following conditions.
• T = -40°C to 85°C, V = VDD ±10%
• Internal clock to nonloaded CLK pin delay # 1 ns @ 85°V/4.5 V
The clock to address output delays are similar, and apply to the following delays.
• Tadr, the clock to address delay
• TCSx, the clock to memory chip select delay
• TIOCSx, the clock to I/O chip select delay
• TIORD, the clock to I/O read strobe delay
• TIOWR, the clock to I/O write strobe delay
• TBUFEN, the clock to I/O buffer enable delay
The data setup time delays are similar for both Tsetup and Thold.
When the spectrum spreader is enabled with the clock doubler, every other clock cycle is
shortened (sometimes lengthened) by a maximum amount given in the table above. The
shortening takes place by shortening the high part of the clock. If the doubler is not
enabled, then every clock is shortened during the low part of the clock period. The maximum shortening for a pair of clocks combined is shown in the table.
Technical Note TN227, Interfacing External I/O with Rabbit 2000/3000 Designs, contains suggestions for interfacing I/O devices to the Rabbit 3000 microprocessors.
30
RabbitCore RCM3200
A.3 Rabbit 3000 DC Characteristics
Table A-5 outlines the DC characteristics for the Rabbit at 3.3 V over the recommended
operating temperature range from Ta = –55°C to +125°C, VDD = 3.0 V to 3.6 V.
Table A-5. 3.3 Volt DC Characteristics
Symbol
Parameter
Test Conditions
Min
IIH
Input Leakage High
VIN = VDD, VDD = 3.3 V
IIL
Input Leakage Low
(no pull-up)
VIN = VSS, VDD = 3.3 V -1
IOZ
Output Leakage (no pull-up)
VIN = VDD or VSS,
VDD = 3.3 V
VIL
CMOS Input Low Voltage
VIH
CMOS Input High Voltage
VT
CMOS Switching Threshold VDD = 3.3 V, 25°C
VOL
Low-Level Output Voltage
VOH
High-Level Output Voltage
User’s Manual
Typ
Max
1
Units
µA
µA
-1
1
µA
0.3 x VDD V
0.7 x VDD
1.65
IOL = See (sinking)
VDD = 3.0 V
V
0.4
VDD = 3.0 V
IOH = See (sourcing)
V
0.7 x VDD
V
V
31
A.4 I/O Buffer Sourcing and Sinking Limit
Unless otherwise specified, the Rabbit I/O buffers are capable of sourcing and sinking
6.8 mA of current per pin at full AC switching speed. Full AC switching assumes a
29.4 MHz CPU clock and capacitive loading on address and data lines of less than 70 pF
per pin. The absolute maximum operating voltage on all I/O is 5.5 V.
Table A-6 shows the AC and DC output drive limits of the parallel I/O buffers when the
Rabbit 3000 is used in the RCM3200.
Table A-6. I/O Buffer Sourcing and Sinking Capability
Output Drive (Full AC Switching)
Pin Name
All data, address, and I/O
lines with clock doubler
enabled
Sourcing/Sinking Limits
(mA)
Sourcing
Sinking
6.8
6.8
Under certain conditions, the maximum instantaneous AC/DC sourcing or sinking current
may be greater than the limits outlined in Table A-6. The maximum AC/DC sourcing current can be as high as 12.5 mA per buffer as long as the number of sourcing buffers does
not exceed three per VDD or VSS pad, or up to six outputs between pads. Similarly, the
maximum AC/DC sinking current can be as high as 8.5 mA per buffer as long as the number of sinking buffers does not exceed three per VDD or VSS pad, or up to six outputs
between pads. The VDD bus can handle up to 35 mA, and the VSS bus can handle up to
28 mA. All these analyses were measured at 100°C.
32
RabbitCore RCM3200
A.5 Conformal Coating
The areas around the 32 kHz real-time clock crystal oscillator has had the Dow Corning
silicone-based 1-2620 conformal coating applied. The conformally coated area is shown
in Figure A-5. The conformal coating protects these high-impedance circuits from the
effects of moisture and contaminants over time.
R1
R8
C3
U1 C5
C18
C33
C37
C36
R27
R31
JP5
R28
R35
R29
R37
R39
C42
C45
C44
C43
R38
Y3
R40
Q1
R42
C48
R41
C49
C53
C59
C57
C61
L1
R51
R49
R48
R47
R44
U8
C62
L2
R58
C35
JP4
JP3
C39
R25
U5
U6
C47
C30
C29
C28
C27
C32
D1
RP1
C23
R24
U4
C31
Conformally coated
area
C12
C24
R23
C20
C19
R22
R20
C17
R19
J3
C16
C15
R17
R18
C4
R10
R14
C9
C8
C1
R7
R9
C68
C64
C67
C79
Y4
J4
R74
C83
R72
R73
R63 R64
DS1
R71
R75
C86
DS2
DS3
SPD LNK ACT
R69
R67
R70
C75
C74
C72
C71
GND
Figure A-5. RCM3200 Areas Receiving Conformal Coating
Any components in the conformally coated area may be replaced using standard soldering
procedures for surface-mounted components. A new conformal coating should then be
applied to offer continuing protection against the effects of moisture and contaminants.
NOTE: For more information on conformal coatings, refer to Technical Note 303, Conformal Coatings.
User’s Manual
33
A.6 Jumper Configurations
Figure A-6 shows the header locations used to configure the various RCM3200 options
via jumpers.
Top Side
Bottom Side
JP1
JP3
JP4
JP2
JP5
Figure A-6. Location of RCM3200 Configurable Positions
Table A-7 lists the configuration options.
Table A-7. RCM3200 Jumper Configurations
Header
JP1
JP2
JP3
JP4
JP5
Description
Pins Connected
1–2
Buffer disabled
2–3
Buffer enabled
1–2
128K/256K
2–3
512K
1–2
128K/256K
2–3
512K
1–2
Normal Mode
2–3
Bank Mode
1–2
256K
2–3
512K
Factory
Default
Auxiliary I/O data bus
×
Program Execution SRAM Size
×
Flash Memory Size
×
×
Flash Memory Bank Select
×
Data SRAM Size
NOTE: The jumper connections are made using 0 Ω surface-mounted resistors.
34
RabbitCore RCM3200
APPENDIX B. PROTOTYPING BOARD
Appendix B describes the features and accessories of the Prototyping Board, and explains the use of the Prototyping Board to
demonstrate the RCM3200 and to build prototypes of your own
circuits.
User’s Manual
35
B.1 Mechanical Dimensions and Layout
Figure B-1 shows the mechanical dimensions and layout for the RCM3200 Prototyping Board.
MOTOR/ENCODER
J6
PC4
PC3
PC2
PE4
PE5
PC1
PC0
PE6
PE7
PF0
PF1
PF7
PF6
PF2
PF3
PF5
PF4
PA0
PA1
PB7
PB6
PA2
PA3
PB5
PB4
PA4
PA5
PB3
PB2
PA6
PA7
/RES
PE4
UX10
GND
RC15
C2
R1
R4
R3
UX11
RCM2
RC24
RC20
RC23
UX9
R8
R10
R12
R6
RC14
RC22
RC17
RC13
RC16
R7
UX3
RC12
RC21
R9
R11
RC10
R13
R21
+5V
+3.3V
BT1
RC19
C3
R5
R2
+5V
+3.3V
J15
SLAVE
MASTER
J3
C1
Battery
+5V
RN2
J1
+DC
U5
RCM1
J14
GND
C12
RC1
PB0
2.5 MM JACK
D2
U4
RCM30/31/32XX
CORE MODULE
5.25
PC5
PE3
(133)
PE0
PE1
GND
PG7
R17
RC2
RC11
GND
PD5
C11 C10
PG0
PD4
GND
PG2
PG1
PG6
+5V
PG3
PG4
RC18
/IORD
PG5
J11
D1
C13
R20
RN4
SM0
/IOWR
C17
JP1
PD4
DS3
PD5
CURRENT
MEASUREMENT
OPTION
SM1
L1
POWER
PD2
+3.3V
POWER
PD3
RN5
C15
VRAM
VBAT
EXT
/RES
IN
GND
J9
PD6
+DC
PD0
PD7
GND
PD1
+3.3V
GND
NC
GND
RN3
GND
+5V
+3.3V
RN1
UX2
GND
GND
GND
PE4
PE5
PC1
PC0
PE6
PE7
PF0
PF1
PF7
PF6
PF2
PF3
PF5
PF4
PA0
PA1
PB7
PB6
PA2
PA3
PB5
PB4
PA4
PA5
PB3
PB2
PA6
PA7
PB0
/RES
PE4
BD6
GND
BD4
PC2
BD2
PC4
PC3
BD7
PC5
PE3
BD0
PE0
PE1
BD5
PG7
BD3
PD5
BA1
PG0
PD4
BA3
PG2
PG1
PG6
RC7
BD1
PG3
PG4
RC6
+5V
UX4
+5V
C9
U6
C16
GND
/IORD
PG5
+5V
BA0
SM0
/IOWR
+3.3V
+3.3V
RCM30/31/32XX
CORE MODULE
+5V
J8
GND
PD4
/RES
LCD
PD2
PD5
+5V
PD6
PD3
SM1
+5V
PD7
VRAM
+3.3V
BPE3
+3.3V
R16
GND
VBAT
EXT
/RES
IN
+3.3V
TP1
PD0
R15
PD1
DISPLAY BOARD
RC25
RC4
RC5
C14
RC27
U3
U3
RC28
RC29
RC26
UX5
R14
RC9
UX7
U1
RCM30/31/32XX SERIES
P R O TO T Y P I N G B O A R D
C5
C8
J12
RESET
C4
NC
BA2
GND
GND
C6
RxC TxC
GND
J5
J4
TxB RxB
GND
J13
S2
S3
PG6
PG7
DS1
DS2
J10
C7
RS-232
DISPLAY BOARD
UX13
J7
DISPLAY BOARD
6.75
(171)
Figure B-1. Prototyping Board Dimensions
36
RabbitCore RCM3200
Table B-1 lists the electrical, mechanical, and environmental specifications for the Prototyping Board.
Table B-1. Prototyping Board Specifications
Parameter
Specification
Board Size
5.25" × 6.75" × 1.00" (133 mm × 171 mm × 25 mm)
Operating Temperature
–20°C to +60°C
Humidity
5% to 95%, noncondensing
Input Voltage
8 V to 24 V DC
Maximum Current Draw
800 mA max. for +3.3 V supply,
(including user-added circuits) 1 A total +3.3 V and +5 V combined
Prototyping Area
2.0" × 3.5" (50 mm × 90 mm) throughhole, 0.1" spacing,
additional space for SMT components
Standoffs/Spacers
5, accept 4-40 × 3/8 screws
B.2 Power Supply
The RCM3200 requires a regulated 3.3 V ± 0.15 V DC power source to operate. Depending on the amount of current required by the application, different regulators can be used
to supply this voltage.
The Prototyping Board has an onboard +5 V switching power regulator from which a
+3.3 V linear regulator draws its supply. Thus both +5 V and +3.3 V are available on the
Prototyping Board.
The Prototyping Board itself is protected against reverse polarity by a Shottky diode at D2
as shown in Figure B-2.
SWITCHING POWER REGULATOR
POWER
IN
J9/J11
1
2
D2
DCIN
DL4003
C17
47 µF
+RAW
3
+5 V
LINEAR POWER
REGULATOR +3.3 V
3
U5
330 µH
LM2575
340 µF
LM1117
U1
1
2
10 µF
L1
D1
1N5819
Figure B-2. Prototyping Board Power Supply
User’s Manual
37
B.3 Using the Prototyping Board
The Prototyping Board is actually both a demonstration board and a prototyping board.
As a demonstration board, it can be used to demonstrate the functionality of the RCM3200
right out of the box without any modifications to either board. There are no jumpers or dip
switches to configure or misconfigure on the Prototyping Board so that the initial setup is
very straightforward.
The Prototyping Board comes with the basic components necessary to demonstrate the
operation of the RCM3200. Two LEDs (DS1 and DS2) are connected to PG6 and PG7,
and two switches (S2 and S3) are connected to PG1 and PG0 to demonstrate the interface
to the Rabbit 3000 microprocessor. Reset switch S1 is the hardware reset for the
RCM3200.
The Prototyping Board provides the user with RCM3200 connection points brought out conveniently to labeled points at headers J2 and J4 on the Prototyping Board. Small to medium
circuits can be prototyped using point-to-point wiring with 20 to 30 AWG wire between the
prototyping area and the holes at locations J2 and J4. The holes are spaced at 0.1" (2.5 mm),
and 40-pin headers or sockets may be installed at J2 and J4. The pinouts for locations J2 and
J4, which correspond to headers J1 and J2, are shown in Figure B-3.
J4
J2
GND
GND
VBAT_EXT
/RESET_IN
SMODE0
/IOWR
PG5
PG7
PE1
PE4
PE6
PF7
PF5
PB7
PB5
PB3
PB0
NC
+3.3V
VRAM
SMODE1
/IORD
PG4
PG6
PE0
PE3
PE5
PE7
PF6
PF4
PB6
PB4
PB2
/RES
PD1
PD7
PD3
PD5
PG3
PG1
PC7
PC5
PC3
PC1
PF0
PF2
PA0
PA2
PA4
PA6
STATUS
PD0
PD6
PD2
PD4
PG2
PG0
PC6
PC4
PC2
PC0
PF1
PF3
PA1
PA3
PA5
PA7
GND
n.c. = not connected
Figure B-3. Prototyping Board Pinout
(Top View)
The small holes are also provided for surface-mounted components that may be installed
around the prototyping area.
There is a 2.0" × 3.5" through-hole prototyping space available on the Prototyping Board.
+3.3 V, +5 V, and GND traces run along the edge of the Prototyping Board for easy access.
38
RabbitCore RCM3200
B.3.1 Adding Other Components
There are pads that can be used for surface-mount prototyping involving SOIC devices.
There is provision for seven 16-pin devices (six on one side, one on the other side). There
are 10 sets of pads that can be used for 3- to 6-pin SOT23 packages. There are also pads
that can be used for SMT resistors and capacitors in an 0805 SMT package. Each component has every one of its pin pads connected to a hole in which a 30 AWG wire can be soldered (standard wire wrap wire can be soldered in for point-to-point wiring on the
Prototyping Board). Because the traces are very thin, carefully determine which set of
holes is connected to which surface-mount pad.
B.3.2 Measuring Current Draw
The Prototyping Board has a current-measurement feature available on header JP1. Normally, a jumper connects pins 1–2 and pins 5–6 on header JP1, which provide jumper connections for the +5 V and the +3.3 V regulated voltages respectively. You may remove a
jumper and place an ammeter across the pins instead, as shown in the example in
Figure B-4, to measure the current being drawn.
0
+5V
+3.3V
A
CURRENT
MEASUREMENT
OPTION
JP1
Figure B-4. Prototyping Board Current-Measurement Option
B.3.3 Other Prototyping Board Modules and Options
An optional LCD/keypad module is available that can be mounted on the Prototyping
Board. Refer to Appendix C, “LCD/Keypad Module,” for complete information.
A motor control option is available for development by the customer. Refer to
Appendix F, “Motor Control Option,” for complete information on using the Rabbit
3000’s Parallel Port F in conjunction with this application.
User’s Manual
39
40
RabbitCore RCM3200
APPENDIX C. LCD/KEYPAD MODULE
An optional LCD/keypad is available for the Prototyping Board.
Appendix C describes the LCD/keypad and provides the software APIs to make full use of the LCD/keypad.
C.1 Specifications
Two optional LCD/keypad modules—with or without a panel-mounted bezel—are available
for use with the Prototyping Board. They are shown in Figure C-1.
LCD/Keypad Modules
Figure C-1. LCD/Keypad Modules Models
Contact your Z-World or Rabbit Semiconductor sales representative or your authorized
Z-World/Rabbit Semiconductor distributor for further assistance in purchasing an
LCD/keypad module.
Mounting hardware and a 60 cm (24") extension cable are also available for the LCD/keypad module through your Z-World/Rabbit Semiconductor sales representative or authorized distributor.
User’s Manual
41
Table C-1 lists the electrical, mechanical, and environmental specifications for the
LCD/keypad module.
Table C-1. LCD/Keypad Specifications
Parameter
Specification
Board Size
2.60" × 3.00" × 0.75"
(66 mm × 76 mm × 19 mm)
Temperature
Operating Range: 0°C to +50°C
Storage Range: –40°C to +85°C
Humidity
5% to 95%, noncondensing
Power Consumption
1.5 W maximum*
Connections
Connects to high-rise header sockets on the Prototyping Board
LCD Panel Size
122 × 32 graphic display
Keypad
7-key keypad
LEDs
Seven user-programmable LEDs
* The backlight adds approximately 650 mW to the power consumption.
42
RabbitCore RCM3200
C.2 Contrast Adjustments for All Boards
Depending on when you acquired your LCD/keypad module, you will be able to set the
contrast on the LCD display by adjusting the potentiometer at R2 or by setting the voltage
for 5 V by not using the jumper across any pins on header J5 as shown in Figure C-2. Only
one of these two options is available on a given LCD/keypad module.
LCD/Keypad Module Jumper Configurations
Description
Pins
Connected
Factory
Default
2.8 V
1–2
×
3.3 V
3–4
5V
n.c.
C9
U3
D1
C7
JP1
R3
U2
C4
U1
R4
R5
C11
C13
U4
J5
CR1
C12
R7
LCD1
R6
D2 C1
C6
C10
R2
C5
C2
Contrast
Adjustment
C3
J5
R1
Header
Q1
J5
Part No. 101-0541
R8
R26
2
R10
Q4
Q6
OTHER LP3500
3.3 V 2.8 V
n.c. = 5 V
R12
R9
Q7
Q2
U6
U5
Q5
R15
R18
R14
R16
R13
R20
4
R17
1
R21
R11
J5
3
Q3
R19
2
R23
1
4
R22
3
J1
R25
Q8
J2
U7 C14
C16 R24
C15
KP1
C17
RN1
DISPLAY
BOARD
J4
Figure C-2. LCD/Keypad Module Voltage Settings
NOTE: Older LCD/keypad modules that do not have a header at J5 or a contrast adjustment potentiometer at R2 are limited to operate only at 5 V, and will work with the
Prototyping Board. The older LCD/keypad modules are no longer being sold.
User’s Manual
43
C.3 Keypad Labeling
The keypad may be labeled according to your needs. A template is provided in Figure C-3
to allow you to design your own keypad label insert.
1.10
(28)
2.35
(60)
Figure C-3. Keypad Template
To replace the keypad legend, remove the old legend and insert your new legend prepared
according to the template in Figure C-3. The keypad legend is located under the blue keypad matte, and is accessible from the left only as shown in Figure C-4.
Keypad label is located
under the blue keypad matte.
Figure C-4. Removing and Inserting Keypad Label
44
RabbitCore RCM3200
C.4 Header Pinouts
DB6B
DB4B
DB2B
DB0B
A1B
A3B
GND
LED7
LED5
LED3
LED1
/RES
VCC
Figure C-5 shows the pinouts for the LCD/keypad module.
J3
GND
LED7
LED5
LED3
LED1
/RES
VCC
GND
DB6B
DB4B
DB2B
DB0B
A1B
A3B
DB7B
DB5B
DB3B
DB1B
A0B
A2B
GND
GND
LED6
LED4
LED2
/CS
+5BKLT
J1
GND
GND
LED6
LED4
LED2
PE7
+5BKLT
GND
DB7B
DB5B
DB3B
DB1B
A0B
A2B
J2
Figure C-5. LCD/Keypad Module Pinouts
C.4.1 I/O Address Assignments
The LCD and keypad on the LCD/keypad module are addressed by the /CS strobe as
explained in Table C-2.
Table C-2. LCD/Keypad Module Address Assignment
Address
User’s Manual
Function
0xC000
Device select base address (/CS)
0xCxx0–0xCxx7
LCD control
0xCxx8
LED enable
0xCxx9
Not used
0xCxxA
7-key keypad
0xCxxB (bits 0–6)
7-LED driver
0xCxxB (bit 7)
LCD backlight on/off
0xCxxC–ExxF
Not used
45
C.5 Mounting LCD/Keypad Module on the Prototyping Board
Install the LCD/keypad module on header sockets J7, J8, and J10 of the Prototyping Board
as shown in Figure C-6. Be careful to align the pins over the headers, and do not bend
them as you press down to mate the LCD/keypad module with the Prototyping Board.
MOTOR/ENCODER
J6
C11 C10
MASTER
C62
/IOWR
PG4
PG1
PG0
PG5
PG6
PD4
PD5
C30
PG7
PE0
PC5
PC4
PE1
PE3
PC3
PC2
PE4
PE5
PC1
PC0
PE6
PE7
PF0
PF1
PF7
JP4
C39
JP3
C37
C36
R28
JP5
GND
R24
R31
R27
C35
C28
C27
C16
C15
C19
C24
C20
C33
C29
C17
R10
R14
C1
U1 C5
RP1
C3
C4
C6
RxC TxC
GND
J5
J4
TxB RxB
GND
C16
DISPLAY BOARD
RC25
RC4
RC5
C14
RC27
U3
U3
RC28
RC29
RC26
UX5
R14
UX13
RCM3000 PROTOTYPING BOARD
J13
S2
S3
PG6
PG7
DS1
DS2
C7
RS-232
U6
UX7
R8
C9
C8
C9
C8
RESET
J8
+5V
RC9
C5
J12
RC7
+5V
UX4
R17
R18
C18
R19
C12
R20
C4
R23
/RES STATUS
R25
PB0
U4
PA7
C31
PA5
PA6
U1
RC6
D1
PA4
PB2
R29
R37
R39
R40
PB4
PB3
Y3
PB5
C42
PA3
R35
PA1
PA2
U5
PF3
PA0
PB6
U6
PF2
PF4
Q1
PF6
PF5
PB7
+3.3V
+3.3V
+5V
BD6
PG2
BD4
PD4
PG3
GND
+5V
J8
BD7
PD2
PD5
/IORD
+3.3V
BD5
PD3
SM1
C45
C44
C43
R38
VRAM
SM0
C32
VBAT
EXT
/RES
IN
GND
GND
+3.3V
BD2
C48
R42
PD6
R1
PD7
R7
R9
+3.3V
R22
GND
C23
R41
PD0
GND
C53
PD1
BD0
C57
C49
UX2
C47
NC
BA1
R51
R49
R48
C61
L1
R9
R11
R13
RC2
RC11
GND
GND
R72
C75
R74
C64
C67
L2
RC21
RC10
C59
DS3
DS2
DS1
UX3
RC1
C72
C71
C68
RC22
R7
R21
R12
R6
RC16
R58
R67
R70
C83
R8
RC17
RC13
RC12
RC24
RC23
R10
J4
UX9
RC14
UX11
RCM3000
RABBITCORE
R63 R64
GND
R75
RC20
RCM2
R71
SPD LNK ACT
C2
C3
R5
R2
RC19
C86
RC15
R4
C79
Y4
C1
R3
J15
SLAVE
UX10
GND
R1
+DC
BT1
RCM3000 RABBITCORE
RCM1
J14
PA7
BA3
PA5
J3
R69
RN2
J1
GND
R73
PA4
BD3
PE4
GND
PA6
/RES
BD1
PA3
PB2
PB0
GND
PA2
PB4
PB3
+3.3V
BA0
PB6
PB5
+5V
+3.3V
GND
PB7
Battery
BA2
PA1
/RES
LCD
PF3
PA0
+5V
PF1
PF2
PF4
+5V
PF0
PF6
PF5
BPE3
PE7
PF7
+5V
GND
PE6
R16
PC0
+5V
PC1
U5
C74
PE5
C12
+5V
PE4
2.5 MM JACK
D2
U4
TP1
PC2
R15
PC3
RC18
PE3
R47
PC4
PE1
R44
PD5
PC5
J3
PG0
PD4
PE0
J11
U8
PG2
PG1
PG6
JP1
PG3
PG4
PG7
CURRENT
MEASUREMENT
OPTION
/IORD
PG5
C17
D1
C13
R20
R17
RN4
SM0
/IOWR
L1
DS3
PD4
+3.3V
POWER
PD2
PD5
C15
PD3
SM1
RN5
POWER
VRAM
VBAT
EXT
/RES
IN
GND
J9
PD6
+DC
PD7
GND
PD0
+3.3V
GND
PD1
GND
RN3
NC
+5V
+3.3V
RN1
GND
J10
DISPLAY BOARD
J10
J7
J7
DISPLAY BOARD
Figure C-6. Install LCD/Keypad Module on Prototyping Board
46
RabbitCore RCM3200
C.6 Bezel-Mount Installation
This section describes and illustrates how to bezel-mount the LCD/keypad module. Follow these steps for bezel-mount installation.
1. Cut mounting holes in the mounting panel in accordance with the recommended dimensions in Figure C-7, then use the bezel faceplate to mount the LCD/keypad module onto
the panel.
0.125 D, 4x
(5.8)
2.870
(86.4)
(3.3)
0.230
0.130
CUTOUT
3.400
(3)
(72.9)
3.100
(78.8)
Figure C-7. Recommended Cutout Dimensions
2. Carefully “drop in” the LCD/keypad module with the bezel and gasket attached.
User’s Manual
47
3. Fasten the unit with the four 4-40 screws and washers included with the LCD/keypad
module. If your panel is thick, use a 4-40 screw that is approximately 3/16" (5 mm)
longer than the thickness of the panel.
Bezel/Gasket
DISPLAY BOARD
U1
C1
U2
C4
U3
C3
C2
Q1
R17
D1
J1
R1
R2
R4
R3
R5
R7
R6
R8
R15
R14
R13
R12
R11
R9
R10
Panel
R18
Q2
Q3
Q4
Q5
Q6
Q8
Q7
C5
R16
KP1
J3
RN1
U4
C6
C7
C8
J2
Figure C-8. LCD/Keypad Module Mounted in Panel (rear view)
Carefully tighten the screws until the gasket is compressed and the plastic bezel faceplate is touching the panel.
Do not tighten each screw fully before moving on to the next screw. Apply only one or
two turns to each screw in sequence until all are tightened manually as far as they can
be so that the gasket is compressed and the plastic bezel faceplate is touching the panel.
48
RabbitCore RCM3200
C.6.1 Connect the LCD/Keypad Module to Your Prototyping Board
The LCD/keypad module can be located as far as 2 ft. (60 cm) away from the RCM3000
Series Prototyping Board, and is connected via a ribbon cable as shown in Figure C-9.
MOTOR/ENCODER
J6
MASTER
C64
C67
L2
C62
PB5
PB4
PA4
PA5
PB3
PB2
PA6
PA7
PB0
/RES STATUS
RESET
C45
C44
C43
R38
C39
R24
C28
C27
C6
RxC TxC
GND
J5
J4
TxB RxB
GND
C19
C24
C20
C5
U6
C9
C16
DISPLAY BOARD
RC25
RC4
RC5
C14
RC27
U3
U3
RC28
RC29
RC26
UX13
RCM3000 PROTOTYPING BOARD
J13
S2
S3
PG6
PG7
J7
J10
C7
RS-232
GND
+5V
UX7
C8
J12
C32
JP4
JP3
C37
C36
R28
JP5
R31
R27
U1
BD6
C48
R42
C35
C29
C33
C30
C23
C18
C16
C15
PA3
UX5
R14
GND
+5V
UX4
RC9
C1
PA1
PA2
C9
C8
PF3
PA0
PB6
C4
PF1
PF2
PF4
C17
PF0
PF6
PF5
C12
PE7
PF7
PB7
C4
PE6
C3
PC0
U1 C5
PC2
PC1
R10
R14
PC4
PC3
PE5
R8
PC5
PE3
PE4
RC7
R1
PE0
PE1
RC6
+5V
J8
R7
R9
PG7
RP1
PD5
+5V
R17
R18
PD4
+3.3V
+3.3V
R19
PG6
R20
PG5
R23
PG0
R22
PG1
R25
PG4
U4
PG2
/IOWR
GND
+3.3V
+3.3V
C31
PD4
PG3
J8
GND
GND
D1
PD2
PD5
/IORD
R29
R37
R39
R40
PD3
SM1
Y3
VRAM
SM0
C42
VBAT
EXT
/RES
IN
R35
PD6
U5
PD7
U6
+3.3V
Q1
GND
BD4
C57
C49
UX2
R41
PD0
C53
PD1
C47
NC
BD2
RC2
BD7
C61
L1
R9
R11
R13
RC11
BD5
R51
R49
R48
RC21
RC10
GND
GND
R72
C75
RC1
C72
C68
DS3
DS2
DS1
UX3
C59
R74
C83
J4
C71
RC22
R7
R21
R12
R6
RC16
R58
R67
R70
R8
RC17
RC13
RC12
RC24
RC23
C79
Y4
GND
R71
UX9
RC14
UX11
RCM3000
RABBITCORE
R10
SPD LNK ACT
C3
R5
R2
RC20
RCM2
R75
C2
R3
RC19
R63 R64
RC15
R4
C86
C1
R69
J3
R1
J15
SLAVE
UX10
R73
RN2
J1
+DC
BT1
RCM3000 RABBITCORE
RCM1
J14
BD3
GND
C11 C10
PE4
BD0
/RES
BA1
PA7
PB0
BA3
PA5
PA6
BD1
PA3
PA4
PB2
+5V
+3.3V
GND
PA2
PB4
PB3
+5V
GND
PB6
PB5
GND
+3.3V
GND
PB7
Battery
BA0
PA1
BA2
PF3
PA0
/RES
LCD
PF1
PF2
PF4
+5V
PF0
PF6
PF5
+5V
PE7
PF7
BPE3
PE6
Pin 1
PC0
GND
PC1
U5
R16
PE5
C12
+5V
PE4
2.5 MM JACK
D2
U4
C74
PC2
+5V
PC3
TP1
PC4
PE3
R15
PC6
PC5
PE1
RC18
PG0
PC7
PE0
R47
PG1
PG6
PG7
R44
PG4
PG5
R17
J3
/IOWR
J11
D1
C13
R20
U8
PG2
CURRENT
MEASUREMENT
OPTION
PG3
C17
JP1
/IORD
DS3
SM0
+3.3V
POWER
PD4
C15
PD2
PD5
L1
POWER
PD3
SM1
RN5
J9
VRAM
VBAT
EXT
/RES
IN
GND
GND
PD6
+DC
PD7
GND
PD0
+3.3V
RN4
PD1
GND
RN3
NC
+5V
+3.3V
RN1
GND
DS1
DISPLAY BOARD
DS2
DISPLAY BOARD
U2
C4
Pin 1
DISPLAY BOARD
U1
C1
U3
C3
C2
Q1
R17
D1
J5
J1
R25 R1
R26
R2
R4
R3
R5
R7
R6
R8
R15
R14
R13
R12
R11
R9
R10
R18
Q2
Q3
Q4
Q5
Q6
Q8
Q7
C5
R16
KP1
J3
RN1
U4
C6
C7
C8
J2
Figure C-9. Connecting LCD/Keypad Module to RCM3000 Series Prototyping Board
Note the locations and connections relative to pin 1 on both the RCM3000 Series Prototyping Board and the LCD/keypad module.
Z-World offers 2 ft. (60 cm) extension cables. Contact your authorized Z-World distributor
or a Z-World sales representative at +1(530)757-3737 for more information.
User’s Manual
49
C.7 LCD/Keypad Module Function APIs
When mounted on the Prototyping Board, the LCD/keypad module uses the auxiliary I/O
bus on the Rabbit 3000 chip. Remember to add the line
#define PORTA_AUX_IO
to the beginning of any programs using the auxiliary I/O bus.
C.7.1 LEDs
When power is applied to the LCD/keypad module for the first time, the red LED (DS1)
will come on, indicating that power is being applied to the LCD/keypad module. The red
LED is turned off when the brdInit function executes.
One function is available to control the LEDs, and can be found in the RCM3200.LIB
library in the SAMPLES\RCM3200 directory.
void ledOut(int led, int value);
LED on/off control. This function will only work when the LCD/keypad module is installed on the
Prototyping Board.
PARAMETERS
led is the LED to control.
0 = LED DS1
1 = LED DS2
2 = LED DS3
3 = LED DS4
4 = LED DS5
5 = LED DS6
6 = LED DS7
value is the value used to control whether the LED is on or off (0 or 1).
0 = off
1 = on
RETURN VALUE
None.
SEE ALSO
brdInit
50
RabbitCore RCM3200
C.7.2 LCD Display
The functions used to control the LCD display are contained in the GRAPHIC.LIB library
located in the Dynamic C DISPLAYS\GRAPHIC library directory.
void glInit(void);
Initializes the display devices, clears the screen.
RETURN VALUE
None.
SEE ALSO
glDispOnOFF, glBacklight, glSetContrast, glPlotDot, glBlock, glPlotDot,
glPlotPolygon, glPlotCircle, glHScroll, glVScroll, glXFontInit, glPrintf,
glPutChar, glSetBrushType, glBuffLock, glBuffUnlock, glPlotLine
void glBackLight(int onOff);
Sets the intensity of the backlight, if circuitry is installed.
PARAMETER
: onOff reflects the low to high values (typically 0 to 255, depending on the board design) to set the backlight intensity (0 will turn the backlight off completely.)
RETURN VALUE
None.
SEE ALSO
glInit, glDispOnoff, glSetContrast
void glDispOnOff(int onOff);
Sets the LCD screen on or off. Data will not be cleared from the screen.
PARAMETER
onOff turns the LCD screen on or off
1—turn the LCD screen on
0—turn the LCD screen off
RETURN VALUE
None.
SEE ALSO
glInit, glSetContrast, glBackLight
User’s Manual
51
void glSetContrast(unsigned level);
Sets display contrast (the circuitry is not installed on the LCD/keypad module used with the Prototyping
Board).
PARAMETER
level reflects low to high values (typically 0 to 255, depending on the board design) to give high to low
contrast respectively.
RETURN VALUE
None.
SEE ALSO
glInit, glBacklight, glDispOnoff
void glFillScreen(char pattern);
Fills the LCD display screen with a pattern.
PARAMETER
The screen will be set to all black if pattern is 0xFF, all white if pattern is 0x00, and vertical stripes
for any other pattern.
RETURN VALUE
None.
SEE ALSO
glBlock, glBlankScreen, glPlotPolygon, glPlotCircle
void glBlankScreen(void);
Blanks the LCD display screen (sets LCD display screen to white).
RETURN VALUE
None.
SEE ALSO
glFillScreen, glBlock, glPlotPolygon, glPlotCircle
52
RabbitCore RCM3200
void glBlock(int x, int y, int bmWidth,
int bmHeight);
Draws a rectangular block in the page buffer and on the LCD if the buffer is unlocked. Any portion of the
block that is outside the LCD display area will be clipped.
PARAMETERS
x is the x coordinate of the upper left corner of the block.
y is the y coordinate of the left top corner of the block.
bmWidth is the width of the block.
bmWidth is the height of the block.
RETURN VALUE
None.
SEE ALSO
glFillScreen, glBlankScreen, glPlotPolygon, glPlotCircle
void glPlotVPolygon(int n, int *pFirstCoord);
Plots the outline of a polygon in the LCD page buffer, and on the LCD if the buffer is unlocked. Any portion of the polygon that is outside the LCD display area will be clipped. The function will also return,
doing nothing, if there are less than 3 vertices.
PARAMETERS
n is the number of vertices.
*pFirstCoord is a pointer to array of vertex coordinates: x1,y1, x2,y2, x3,y3,...
RETURN VALUE
None.
SEE ALSO
glPlotPolygon, glFillPolygon, glFillVPolygon
User’s Manual
53
void glPlotPolygon(int n, int y1, int x2, int y2,
...);
Plots the outline of a polygon in the LCD page buffer and on the LCD if the buffer is unlocked. Any portion of the polygon that is outside the LCD display area will be clipped. The function will also return,
doing nothing, if there are less than 3 vertices.
PARAMETERS
n is the number of vertices.
y1 is the y coordinate of the first vertex.
x1 is the x coordinate of the first vertex.
y2 is the y coordinate of the second vertex.
x2 is the x coordinate of the second vertex.
... are the coordinates of additional vertices.
RETURN VALUE
None.
SEE ALSO
glPlotVPolygon, glFillPolygon, glFillVPolygon
void glFillVPolygon(int n, int *pFirstCoord);
Fills a polygon in the LCD page buffer and on the LCD screen if the buffer is unlocked. Any portion of
the polygon that is outside the LCD display area will be clipped. The function will also return, doing
nothing, if there are less than 3 vertices.
PARAMETERS
n is the number of vertices.
*pFirstCoord is a pointer to array of vertex coordinates: x1,y1, x2,y2, x3,y3,...
RETURN VALUE
None.
SEE ALSO
glFillPolygon, glPlotPolygon, glPlotVPolygon
54
RabbitCore RCM3200
void glFillPolygon(int n, int x1, int y1, int x2,
int y2, ...);
Fills a polygon in the LCD page buffer and on the LCD if the buffer is unlocked. Any portion of the polygon that is outside the LCD display area will be clipped.
PARAMETERS
n is the number of vertices.
x1 is the x coordinate of the first vertex.
y1 is the y coordinate of the first vertex.
x2 is the x coordinate of the second vertex.
y2 is the y coordinate of the second vertex.
... are the coordinates of additional vertices.
RETURN VALUE
None.
SEE ALSO
glFillVPolygon, glPlotPolygon, glPlotVPolygon
void glPlotCircle(int xc, int yc, int rad);
Draws a circle in the LCD page buffer and on the LCD if the buffer is unlocked. Any portion of the circle
that is outside the LCD display area will be clipped.
PARAMETERS
xc is the x coordinate of the center of the circle.
yc is the y coordinate of the center of the circle.
rad is the radius of the center of the circle (in pixels).
RETURN VALUE
None.
SEE ALSO
glFillCircle, glPlotPolygon, glFillPolygon
void glFillCircle(int xc, int yc, int rad);
Draws a filled circle in the LCD page buffer and on the LCD if the buffer is unlocked. Any portion of the
circle that is outside the LCD display area will be clipped.
PARAMETERS
xc is the x coordinate of the center of the circle.
yc is the y coordinate of the center of the circle.
rad is the radius of the center of the circle (in pixels).
RETURN VALUE
None.
SEE ALSO
glPlotCircle, glPlotPolygon, glFillPolygon
User’s Manual
55
void glXFontInit(fontInfo *pInfo, char pixWidth,
char pixHeight, unsigned startChar,
unsigned endChar, unsigned long xmemBuffer);
Initializes the font descriptor structure, where the font is stored in xmem. Each font character's bitmap is
column major and byte-aligned.
PARAMETERS
*pInfo is a pointer to the font descriptor to be initialized.
pixWidth is the width (in pixels) of each font item.
pixHeight is the height (in pixels) of each font item.
startChar is the value of the first printable character in the font character set.
endChar is the value of the last printable character in the font character set.
xmemBuffer is the xmem pointer to a linear array of font bitmaps.
RETURN VALUE
None.
SEE ALSO
glPrinf
unsigned long glFontCharAddr(fontInfo *pInfo,
char letter);
Returns the xmem address of the character from the specified font set.
PARAMETERS
*pInfo is the xmem address of the bitmap font set.
letter is an ASCII character.
RETURN VALUE
xmem address of bitmap character font, column major, and byte-aligned.
SEE ALSO
glPutFont, glPrintf
56
RabbitCore RCM3200
void glPutFont(int x, int y, fontInfo *pInfo,
char code);
Puts an entry from the font table to the page buffer and on the LCD if the buffer is unlocked. Each font
character's bitmap is column major and byte-aligned. Any portion of the bitmap character that is outside
the LCD display area will be clipped.
PARAMETERS
x is the x coordinate (column) of the upper left corner of the text.
y is the y coordinate (row) of the left top corner of the text.
*pInfo is a pointer to the font descriptor.
code is the ASCII character to display.
RETURN VALUE
None.
SEE ALSO
glFontCharAddr, glPrintf
void glSetPfStep(int stepX, int stepY);
Sets the glPrintf() printing step direction. The x and y step directions are independent signed values.
The actual step increments depend on the height and width of the font being displayed, which are multiplied by the step values.
PARAMETERS
stepX is the glPrintf x step value
stepY is the glPrintf y step value
RETURN VALUE
None.
SEE ALSO
Use glGetPfStep() to examine the current x and y printing step direction.
int glGetPfStep(void);
Gets the current glPrintf() printing step direction. Each step direction is independent of the other,
and is treated as an 8-bit signed value. The actual step increments depends on the height and width of the
font being displayed, which are multiplied by the step values.
RETURN VALUE
The x step is returned in the MSB, and the y step is returned in the LSB of the integer result.
SEE ALSO
Use glGetPfStep() to control the x and y printing step direction.
User’s Manual
57
void glPutChar(char ch, char *ptr, int *cnt,
glPutCharInst *pInst)
Provides an interface between the STDIO string-handling functions and the graphic library. The
STDIO string-formatting function will call this function, one character at a time, until the entire formatted string has been parsed. Any portion of the bitmap character that is outside the LCD display area will
be clipped.
PARAMETERS
ch is the character to be displayed on the LCD.
*ptr is not used, but is a place holder for STDIO string functions.
*cnt is not used, is a place holder for STDIO string functions.
*pInst is a font descriptor pointer.
RETURN VALUE
None.
SEE ALSO
glPrintf, glPutFont, doprnt
void glPrintf(int x, int y, fontInfo *pInfo,
char *fmt, ...);
Prints a formatted string (much like printf) on the LCD screen. Only the character codes that exist in
the font set are printed, all others are skipped. For example, '\b', '\t', '\n' and '\r' (ASCII backspace, tab,
new line, and carriage return, respectively) will be printed if they exist in the font set, but will not have
any effect as control characters. Any portion of the bitmap character that is outside the LCD display area
will be clipped.
PARAMETERS
x is the x coordinate (column) of the upper left corner of the text.
y is the y coordinate (row) of the upper left corner of the text.
*pInfo is a font descriptor pointer.
*fmt is a formatted string.
... are formatted string conversion parameter(s).
EXAMPLE
glprintf(0,0, &fi12x16, "Test %d\n", count);
RETURN VALUE
None.
SEE ALSO
glXFontInit
58
RabbitCore RCM3200
void glBuffLock(void);
Increments LCD screen locking counter. Graphic calls are recorded in the LCD memory buffer and are
not transferred to the LCD if the counter is non-zero.
NOTE: glBuffLock() and glBuffUnlock() can be nested up to a level of 255, but be
sure to balance the calls. It is not a requirement to use these procedures, but a set of
glBuffLock() and glBuffUnlock() bracketing a set of related graphic calls speeds
up the rendering significantly.
RETURN VALUE
None.
SEE ALSO
glBuffUnlock, glSwap
void glBuffUnlock(void);
Decrements the LCD screen locking counter. The contents of the LCD buffer are transferred to the LCD
if the counter goes to zero.
RETURN VALUE
None.
SEE ALSO
glBuffLock, glSwap
void glSwap(void);
Checks the LCD screen locking counter. The contents of the LCD buffer are transferred to the LCD if the
counter is zero.
RETURN VALUE
None.
SEE ALSO
glBuffUnlock, glBuffLock, _glSwapData (located in the library specifically for the LCD
that you are using)
void glSetBrushType(int type);
Sets the drawing method (or color) of pixels drawn by subsequent graphic calls.
PARAMETER
type value can be one of the following macros.
PIXBLACK draws black pixels.
PIXWHITE draws white pixels.
PIXXOR draws old pixel XOR'ed with the new pixel.
RETURN VALUE
None.
SEE ALSO
glGetBrushType
User’s Manual
59
int glGetBrushType(void);
Gets the current method (or color) of pixels drawn by subsequent graphic calls.
RETURN VALUE
The current brush type.
SEE ALSO
glSetBrushType
void glPlotDot(int x, int y);
Draws a single pixel in the LCD buffer, and on the LCD if the buffer is unlocked. If the coordinates are
outside the LCD display area, the dot will not be plotted.
PARAMETERS
x is the x coordinate of the dot.
y is the y coordinate of the dot.
RETURN VALUE
None.
SEE ALSO
glPlotline, glPlotPolygon, glPlotCircle
void glPlotLine(int x0, int y0, int x1, int y1);
Draws a line in the LCD buffer, and on the LCD if the buffer is unlocked. Any portion of the line that is
beyond the LCD display area will be clipped.
PARAMETERS
x0 is the x coordinate of one endpoint of the line.
y0 is the y coordinate of one endpoint of the line.
x1 is the x coordinate of the other endpoint of the line.
y1 is the y coordinate of the other endpoint of the line.
RETURN VALUE
None.
SEE ALSO
glPlotDot, glPlotPolygon, glPlotCircle
60
RabbitCore RCM3200
void glLeft1(int left, int top, int cols, int rows);
Scrolls byte-aligned window left one pixel, right column is filled by current pixel type (color).
PARAMETERS
left is the upper left corner of bitmap, must be evenly divisible by 8.
top is the left top corner of the bitmap.
cols is the number of columns in the window, must be evenly divisible by 8.
rows is the number of rows in the window.
RETURN VALUE
None.
SEE ALSO
glHScroll, glRight1
void glRight1(int left, int top, int cols, int rows);
Scrolls byte-aligned window right one pixel, left column is filled by current pixel type (color).
PARAMETERS
left is the upper left corner of bitmap, must be evenly divisible by 8.
top is the left top corner of the bitmap.
cols is the number of columns in the window, must be evenly divisible by 8.
rows is the number of rows in the window.
RETURN VALUE
None.
SEE ALSO
glHScroll, glLeft1
void glUp1(int left, int top, int cols, int rows);
Scrolls byte-aligned window up one pixel, bottom column is filled by current pixel type (color).
PARAMETERS
left is the upper left corner of bitmap, must be evenly divisible by 8.
top is the left top corner of the bitmap.
cols is the number of columns in the window, must be evenly divisible by 8.
rows is the number of rows in the window.
RETURN VALUE
None.
SEE ALSO
glVScroll, glDown1
User’s Manual
61
void glDown1(int left, int top, int cols, int rows);
Scrolls byte-aligned window down one pixel, top column is filled by current pixel type (color).
PARAMETERS
left is the upper left corner of bitmap, must be evenly divisible by 8.
top is the left top corner of the bitmap.
cols is the number of columns in the window, must be evenly divisible by 8.
rows is the number of rows in the window.
RETURN VALUE
None.
SEE ALSO
glVScroll, glUp1
void glHScroll(int left, int top, int cols,
int rows, int nPix);
Scrolls right or left, within the defined window by x number of pixels. The opposite edge of the scrolled
window will be filled in with white pixels. The window must be byte-aligned.
Parameters will be verified for the following:
1. The left and cols parameters will be verified that they are evenly divisible by 8. If not, they will
be changed to a value that is a multiple of 8.
2. Parameters will be checked to verify that the scrolling area is valid. The minimum scrolling area is
a width of 8 pixels and a height of one row.
PARAMETERS
left is the upper left corner of bitmap, must be evenly divisible by 8.
top is the left top corner of the bitmap.
cols is the number of columns in the window, must be evenly divisible by 8.
rows is the number of rows in the window.
nPix is the number of pixels to scroll within the defined window (a negative value will produce a scroll
to the left).
RETURN VALUE
None.
SEE ALSO
glVScroll
62
RabbitCore RCM3200
void glVScroll(int left, int top, int cols,
int rows, int nPix);
Scrolls up or down, within the defined window by x number of pixels. The opposite edge of the scrolled
window will be filled in with white pixels. The window must be byte-aligned.
Parameters will be verified for the following:
1. The left and cols parameters will be verified that they are evenly divisible by 8. If not, they will
be changed to a value that is a multiple of 8.
2. Parameters will be checked to verify that the scrolling area is valid. The minimum scrolling area is
a width of 8 pixels and a height of one row.
PARAMETERS
left is the upper left corner of bitmap, must be evenly divisible by 8.
top is the left top corner of the bitmap.
cols is the number of columns in the window, must be evenly divisible by 8.
rows is the number of rows in the window.
nPix is the number of pixels to scroll within the defined window (a negative value will produce a scroll
up).
RETURN VALUE
None.
SEE ALSO
glHScroll
void glXPutBitmap(int left, int top, int width,
int height, unsigned long bitmap);
Draws bitmap in the specified space. The data for the bitmap are stored in xmem. This function calls
glXPutFastmap automatically if the bitmap is byte-aligned (the left edge and the width are each
evenly divisible by 8).
Any portion of a bitmap image or character that is outside the LCD display area will be clipped.
PARAMETERS
left is the upper left corner of the bitmap.
top is the upper left corner of the bitmap.
width is the width of the bitmap.
height is the height of the bitmap.
bitmap is the address of the bitmap in xmem.
RETURN VALUE
None.
SEE ALSO
glXPutFastmap, glPrintf
User’s Manual
63
void glXPutFastmap(int left, int top, int width,
int height, unsigned long bitmap);
Draws bitmap in the specified space. The data for the bitmap are stored in xmem. This function is like
glXPutBitmap, except that it is faster. The restriction is that the bitmap must be byte-aligned.
Any portion of a bitmap image or character that is outside the LCD display area will be clipped.
PARAMETERS
left is the upper left corner of the bitmap, must be evenly divisible by 8.
top is the upper left corner of the bitmap.
width is the width of the bitmap, must be evenly divisible by 8.
height is the height of the bitmap.
bitmap is the address of the bitmap in xmem.
RETURN VALUE
None.
SEE ALSO
glXPutBitmap, glPrintf
int TextWindowFrame(windowFrame *window,
fontInfo *pFont, int x, int y, int winWidth,
int winHeight)
Defines a text-only display window. This function provides a way to display characters within the text
window using only character row and column coordinates. The text window feature provides end-of-line
wrapping and clipping after the character in the last column and row is displayed.
NOTE: Execute the TextWindowFrame function before other Text... functions.
PARAMETERS
*window is a window frame descriptor pointer.
*pFont is a font descriptor pointer.
x is the x coordinate of where the text window frame is to start.
y is the y coordinate of where the text window frame is to start.
winWidth is the width of the text window frame.
winHeight is the height of the text window frame.
RETURN VALUE
0—window frame was successfully created.
-1—x coordinate + width has exceeded the display boundary.
-2—y coordinate + height has exceeded the display boundary.
64
RabbitCore RCM3200
void TextGotoXY(windowFrame *window, int col,
int row);
Sets the cursor location on the display of where to display the next character. The display location is
based on the height and width of the character to be displayed.
NOTE: Execute the TextWindowFrame function before using this function.
PARAMETERS
*window is a pointer to a font descriptor.
col is a character column location.
row is a character row location.
RETURN VALUE
None.
SEE ALSO
TextPutChar, TextPrintf, TextWindowFrame
void TextCursorLocation(windowFrame *window,
int *col, int *row);
Gets the current cursor location that was set by a Graphic Text... function.
NOTE: Execute the TextWindowFrame function before using this function.
PARAMETERS
*window is a pointer to a font descriptor.
*col is a pointer to cursor column variable.
*row is a pointer to cursor row variable.
RETURN VALUE
Lower word = Cursor Row location
Upper word = Cursor Column location
SEE ALSO
TextGotoXY, TextPrintf, TextWindowFrame, TextCursorLocation
void TextPutChar(struct windowFrame *window, char ch);
Displays a character on the display where the cursor is currently pointing. If any portion of a bitmap
character is outside the LCD display area, the character will not be displayed.
NOTE: Execute the TextWindowFrame function before using this function.
PARAMETERS
*window is a pointer to a font descriptor.
ch is a character to be displayed on the LCD.
RETURN VALUE
None.
SEE ALSO
TextGotoXY, TextPrintf, TextWindowFrame, TextCursorLocation
User’s Manual
65
void TextPrintf(struct windowFrame *window,
char *fmt, ...);
Prints a formatted string (much like printf) on the LCD screen. Only printable characters in the font
set are printed, also escape sequences, '\r' and '\n' are recognized. All other escape sequences will be
skipped over; for example, '\b' and 't' will print if they exist in the font set, but will not have any effect as
control characters.
The text window feature provides end-of-line wrapping and clipping after the character in the last column and row is displayed.
NOTE: Execute the TextWindowFrame function before using this function.
PARAMETERS
*window is a pointer to a font descriptor.
*fmt is a formatted string.
... are formatted string conversion parameter(s).
EXAMPLE
TextPrintf(&TextWindow, "Test %d\n", count);
RETURN VALUE
None.
SEE ALSO
TextGotoXY, TextPutChar, TextWindowFrame, TextCursorLocation
66
RabbitCore RCM3200
C.7.3 Keypad
The functions used to control the keypad are contained in the KEYPAD7.LIB library
located in the Dynamic C KEYPADS library directory.
void keyInit(void);
Initializes keypad process
RETURN VALUE
None.
SEE ALSO
brdInit
void keyConfig(char cRaw, char cPress,
char cRelease, char cCntHold, char cSpdLo,
char cCntLo, char cSpdHi);
Assigns each key with key press and release codes, and hold and repeat ticks for auto repeat and
debouncing.
PARAMETERS
cRaw is a raw key code index.
1x7 keypad matrix with raw key code index assignments (in brackets):
[0]
[1]
[4]
[2]
[5]
[3]
[6]
User Keypad Interface
cPress is a key press code
An 8-bit value is returned when a key is pressed.
0 = Unused.
See keypadDef() for default press codes.
cRelease is a key release code.
An 8-bit value is returned when a key is pressed.
0 = Unused.
cCntHold is a hold tick.
How long to hold before repeating.
0 = No Repeat.
cSpdLo is a low-speed repeat tick.
How many times to repeat.
0 = None.
cCntLo is a low-speed hold tick.
How long to hold before going to high-speed repeat.
0 = Slow Only.
User’s Manual
67
cSpdHi is a high-speed repeat tick.
How many times to repeat after low speed repeat.
0 = None.
RETURN VALUE
None.
SEE ALSO
keyProcess, keyGet, keypadDef
void keyProcess(void);
Scans and processes keypad data for key assignment, debouncing, press and release, and repeat.
NOTE: This function is also able to process an 8 × 8 matrix keypad.
RETURN VALUE
None
SEE ALSO
keyConfig, keyGet, keypadDef
char keyGet(void);
Get next keypress
RETURN VALUE
The next keypress, or 0 if none
SEE ALSO
keyConfig, keyProcess, keypadDef
int keyUnget(char cKey);
Push keypress on top of input queue
PARAMETER
cKey
RETURN VALUE
None.
SEE ALSO
keyGet
68
RabbitCore RCM3200
void keypadDef();
Configures the physical layout of the keypad with the desired ASCII return key codes.
Keypad physical mapping 1 × 7
0
4
1
['L']
5
2
['U']
['–']
6
['D']
3
['R']
['+']
['E']
where
'E' represents the ENTER key
'D' represents Down Scroll
'U' represents Up Scroll
'R' represents Right Scroll
'L' represents Left Scroll
Example: Do the followingfor the above physical vs. ASCII return key codes.
keyConfig
keyConfig
keyConfig
keyConfig
keyConfig
keyConfig
keyConfig
(
(
(
(
(
(
(
3,'R',0,
6,'E',0,
2,'D',0,
4,'-',0,
1,'U',0,
5,'+',0,
0,'L',0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
0
0
0
0
0
0
);
);
);
);
);
);
);
Characters are returned upon keypress with no repeat.
RETURN VALUE
None.
SEE ALSO
keyConfig, keyGet, keyProcess
void keyScan(char *pcKeys);
Writes "1" to each row and reads the value. The position of a keypress is indicated by a zero value in a bit
position.
PARAMETER
*pcKeys is the address of the value read.
RETURN VALUE
None.
SEE ALSO
keyConfig, keyGet, keypadDef, keyProcess
User’s Manual
69
C.8 Sample Programs
Sample programs illustrating the use of the LCD/keypad module with the Prototyping
Board are provided in the SAMPLES\RCM3200 directory.
These sample programs use the auxiliary I/O bus on the Rabbit 3000 chip, and so the
#define PORTA_AUX_IO line is already included in the sample programs.
70
RabbitCore RCM3200
APPENDIX D. POWER SUPPLY
Appendix D provides information on the current requirements
of the RCM3200, and includes some background on the chip
select circuit used in power management.
D.1 Power Supplies
The RCM3200 requires a regulated 3.3 V ± 0.15 V DC power source. The RabbitCore
design presumes that the voltage regulator is on the user board, and that the power is made
available to the RCM3200 board through header J2.
An RCM3200 with no loading at the outputs operating at 29.4 MHz typically draws 145 mA.
The RCM3200 will consume an additional 10 mA when the programming cable is used to
connect the programming header, J3, to a PC.
D.1.1 Battery-Backup Circuits
The RCM3200 does not have a battery, but there is provision for a customer-supplied battery to back up the data SRAM and keep the internal Rabbit 3000 real-time clock running.
Header J2, shown in Figure D-1, allows access to the external battery. This header makes
it possible to connect an external 3 V power supply. This allows the SRAM and the internal Rabbit 3000 real-time clock to retain data with the RCM3200 powered down.
External
Battery
J2
VRAM 29
30
VBAT_EXT
+3.3V
32
GND
31
Figure D-1. External Battery Connections
at Header J5
A lithium battery with a nominal voltage of 3 V and a minimum capacity of 165 mA·h is
recommended. A lithium battery is strongly recommended because of its nearly constant
nominal voltage over most of its life.
User’s Manual
71
The drain on the battery by the RCM3200 is typically 12 µA when no other power is supplied. If a 165 mA·h battery is used, the battery can last almost 2 years:
165 mA·h
------------------------ = 1.6 years.
12 µA
The actual life in your application will depend on the current drawn by components not on
the RCM3200 and the storage capacity of the battery. Note that the shelf life of a lithium ion
battery is ultimately 10 years. The RCM3200 does not drain the battery while it is powered
up normally.
D.1.2 Reset Generator
The RCM3200 uses a reset generator to reset the Rabbit 3000 microprocessor when the voltage drops below the voltage necessary for reliable operation. The reset occurs between
2.85 V and 3.00 V, typically 2.93 V. The RCM3200 has a reset output, pin 1 on header J2.
D.2 Optional +5 V Output
The RCM3200 boards have an onboard charge pump that provides the +5 V needed by the
RealTek Ethernet chip.
72
RabbitCore RCM3200
APPENDIX E. PROGRAMMING CABLE
Appendix E provides additional information for the Rabbit 3000®
microprocessor when using the DIAG and PROG connectors on the
programming cable. The PROG connector is used only when the programming cable is attached to the programming connector (header J3)
while a new application is being developed. Otherwise, the DIAG connector on the programming cable allows the programming cable to be
used as an RS-232 to CMOS level converter for serial communication,
which is appropriate for monitoring or debugging a RabbitCore system
while it is running.
User’s Manual
73
The programming port, which is shown in Figure E-1, can serve as a convenient communications port for field setup or other occasional communication need (for example, as a diagnostic port). If the port is simply to perform a setup function, that is, write setup
information to flash memory, then the controller can be reset through the programming
port and a cold boot performed to start execution of a special program dedicated to this
functionality.
PROGRAMMING PORT PIN ASSIGNMENTS
(Rabbit LQFP pins are shown in parenthesis)
1
2
3
4
5
6
7
8
9
10
Programming Port
Pin Numbers
1.
2.
3.
4.
5.
6.
7.
8.
9.
RXA (66)
GND
CKLKA (117)
+5 V/+3 V
/RESET
TXA (67)
n.c.
STATUS (output) (4)
SMODE0 (45)
10. SMODE1 (44)
~50 kW
~50 kW
~10 kW
~50 kW
~50 kW
+
+
+
GND
GND
Figure E-1. Programming Port Pin Assignments
When the PROG connector is used, the /RESET line can be asserted by manipulating
DTR and the STATUS line can be read as DSR on the serial port. The target can be
restarted by pulsing reset and then, after a short delay, sending a special character string at
2400 bps. To simply restart the BIOS, the string 80h, 24h, 80h can be sent. When the
BIOS is started, it can tell whether the programming cable is connected because the
SMODE1 and SMODE0 pins are sensed as being high.
Alternatively, the DIAG connector can be used to connect the programming port. The
/RESET line and the SMODE1 and SMODE0 pins are not connected to this connector.
The programming port is then enabled as a diagnostic port by polling the port periodically
to see if communication needs to begin or to enable the port and wait for interrupts. The
pull-up resistors on RXA and CLKA prevent spurious data reception that might take place
if the pins floated.
If the clocked serial mode is used, the serial port can be driven by having two toggling
lines that can be driven and one line that can be sensed. This allows a conversation with a
device that does not have an asynchronous serial port but that has two output signal lines
and one input signal line.
The line TXA (also called PC6) is zero after reset if the cold-boot mode is not enabled. A
possible way to detect the presence of a cable on the programming port is for the cable to
connect TXA to one of the SMODE pins and then test for the connection by raising PC6
(by configuring it as a general output bit) and reading the SMODE pin after the cold-boot
mode has been disabled. The value of the SMODE pin is read from the SPCR register.
74
RabbitCore RCM3200
Once you establish that the programming port will never again be needed for programming, it is possible to use the programming port for additional I/O lines. Table E-1 lists the
pins available for this alternate configuration.
Table E-1. RCM3200 Programming Port Pinout Configurations
Header J3
Pin
Pin Name
Default Use
Notes
1
RXA
2
GND
3
CLKA
4
VCC
5
RESET
6
TXA
8
STATUS
Output
9
SMODE0
Input
Must be low when
RCM3200 boots up
10
SMODE1
Input
Must be low when
RCM3200 boots up
User’s Manual
Serial Port A
Alternate Use
PC7—Input
PB1—Bitwise or parallel
programmable input
Connected to reset
generator U4
Serial Port A
PC6—Output
75
76
RabbitCore RCM3200
APPENDIX F. MOTOR CONTROL OPTION
The Prototyping Board has a header at J6 for a motor control option.
While Z-World and Rabbit Semiconductor do not support this option
at this time, this appendix provides additional information about Parallel Port F on the Rabbit 3000 microprocessor to enable you to use this
feature on the Prototyping Board for your needs.
F.1 Overview
The Parallel Port F connector on the Prototyping Board, J6, gives access to all 8 pins of
Parallel Port F, along with +5 V. This appendix describes the function of each pin, and the
ways they may be used for motion-control applications. It should be read in conjunction
with the Rabbit 3000 Microprocessor User’s Manual and the RCM3200 and the Prototyping Board schematics.
User’s Manual
77
F.2 Header J6
The connector is a 2 × 5, 0.1" pitch header suitable for connecting to a IDC receptacle,
with the following pin allocations.
Table F-1. Prototyping Board Header J6 Pinout
Pin
Rabbit 3000
Primary Function
Alternate Function 1 Alternate Function 2
1
Parallel Port F, bit 0
General-purpose I/O port
Quadrature decoder 1 Q
SCLK_D
input
2
Parallel Port F, bit 1
General-purpose I/O port
Quadrature decoder 1 I
input
3
Parallel Port F, bit 2
General-purpose I/O port
Quadrature decoder 2 Q
input
4
Parallel Port F, bit 3
General-purpose I/O port
Quadrature decoder 2 I
input
5
Parallel Port F, bit 4
General-purpose I/O port PWM[0] output
Quadrature decoder 1 Q
input
6
Parallel Port F, bit 5
General-purpose I/O port PWM[1] output
Quadrature decoder 1 I
input
7
Parallel Port F, bit 6
General-purpose I/O port PWM[2] output
Quadrature decoder 2 Q
input
8
Parallel Port F, bit 7
General-purpose I/O port PWM[3] output
Quadrature decoder 2 I
input
9
+5 V
External buffer logic supply
10
0V
Common
SCLK_C
-
All Parallel Port F lines (pins 1 to 8) are pulled up internally to +3.3 V via 100 kΩ resistors. When used as outputs, the port pins will sink up to 6 mA at a VOL of 0.4 V max.
(0.2 V typ), and source up to 6 mA at a VOH of 2.2 V typ. When used as inputs, all pins
are 5 V tolerant.
As the outputs from Parallel Port F are compatible with 3.3 V logic, buffers may be
needed when the external circuit drive requirements exceed the 2.2 V typ logic high and/or
the 6 mA maximum from the Rabbit 3000. The +5 V supply output is provided for supplying interface logic. When used as inputs, the pins on header J6 do not require buffers
unless the input voltage will exceed the 5 V tolerance of the processor pins. Usually, a
simple resistive divider with catching diodes will suffice if higher voltage inputs are
required. If the outputs are configured for open-drain operation, they may be pulled up to
+5 V (while observing the maximum current, of course).
78
RabbitCore RCM3200
F.3 Using Parallel Port F
Parallel Port F is a byte-wide port with each bit programmable for data direction and drive.
These are simple inputs and outputs controlled and reported in the Port F Data Register.
As outputs, the bits of the port are buffered, with the data written to the Port F Data Register transferred to the output pins on a selected timing edge. The outputs of Timer A1,
Timer B1, or Timer B2 can be used for this function, with each nibble of the port having a
separate select field to control this timing. These inputs and outputs are also used for
access to other peripherals on the chip.
As outputs, Parallel Port F can carry the four Pulse Width Modulator outputs on PF4–PF 7
(J6, pins 5–8). As inputs, Parallel Port F can carry the inputs to the Quadrature Decoders
on PF0–PF3 (J6, pins 1–4). When Serial Port C or Serial Port D is used in clocked serial
mode, two pins of Port F (PF0 / J6:1 and PF1 / J6:2) are used to carry the serial clock signals. When the internal clock is selected in these serial ports, the corresponding bit of Parallel Port F is set as an output.
F.3.1 Parallel Port F Registers
Data Direction Register—PFDDR, address 00111111 (0x3F), write-only, default value on
reset 00000000. For each bit position, write a 1 to make the corresponding port line an
output, or 0 to produce an input.
Drive Control Register—PFDCR, address 00111110 (0x3E), Write-only, no default on
reset (port defaults to all inputs). Effective only if the corresponding port bits are set as
outputs, each bit set to 1 configures the corresponding port bit as open drain. Setting the
bit to 0 configures that output as active high or low.
Function Register—PFFR, address 00111101 (0x3D), Write-only, no default on reset.
This register sets the alternate output function assigned to each of the pins of the port.
When set to 0, the corresponding port pin functions normally as an output (if configured to
be an output in PFDDR). When set to 1, each bit sets the corresponding pin to have the
alternate output function as shown in the summary table at the end of this section.
Control Register—PFCR, address 00111100 (0x3C), Write-only, default on reset
xx00xx00. This register sets the transfer clock, which controls the timing of the outputs on
each nibble of the output ports to allow close synchronization with other events. The summary table at the end of this section shows the settings for this register. The default values
on reset transfer the output values on CLK/2.
Data Register—PFDR, address 00111000 (0x38), Read or Write, no default value on
reset. On read, the current state of the pins is reported. On write, the output buffer is written with the value for transfer to the output port register on the next rising edge of the
transfer clock, set in the PFCR.
User’s Manual
79
Table F-2. Parallel Port F Registers
Register Name
Port F Data Register
Mnemonic
PFDR
Bits
0:7
Port F Control Register
R/W
00111000 (0x38)
Value
Reset Value
R/W
xxxxxxxx
Description
Read
Current state of pins
Write
Port buffer. Value transferred to O/P register on next
rising edge of transfer clock.
PFCR
00111100 (0x3C)
Bits
0:1
I/O Address
Value
W only
xx00xx00
Description
00
Lower nibble transfer clock is CLK/2
01
Lower nibble transfer clock is Timer A1
10
Lower nibble transfer clock is Timer B1
11
Lower nibble transfer clock is Timer B2
2:3
xx
These bits are ignored
4:5
00
Upper nibble transfer clock is CLK/2
01
Upper nibble transfer clock is Timer A1
10
Upper nibble transfer clock is Timer B1
11
Upper nibble transfer clock is Timer B2
6:7
xx
These bits are ignored
Port F Function Register
PFFR
00111101 (0x3D)
Bits
Value
W
xxxxxxxx
Description
0:7
0
Corresponding port bits function normally
0
1
Bit 0 carries SCLK_D
1
1
Bit 1 carries SCLK_C
2:3
x
No effect
4
1
Bit 4 carries PWM[0] output
5
1
Bit 5 carries PWM[1] output
6
1
Bit 6 carries PWM[2] output
7
1
Bit 7 carries PWM[3] output
Port F Drive Control Register
PFDCR
00111110 (0x3E)
Bits
0:7
80
Value
W
xxxxxxxx
Description
0
Corresponding port bit is active high or low
1
Corresponding port bit is open drain
RabbitCore RCM3200
Table F-2. Parallel Port F Registers (continued)
Register Name
Port F Data Direction Register
Mnemonic
PFDDR
Bits
0:7
User’s Manual
Value
I/O Address
00111111 (0x3F)
R/W
W
Reset Value
00000000
Description
0
Corresponding port bit is an input
1
Corresponding port bit is an output
81
F.4 PWM Outputs
The Pulse-Width Modulator consists of a 10-bit free-running counter and four width registers. Each PWM output is high for n + 1 counts out of the 1024-clock count cycle, where n
is the value held in the width register. The PWM output high time can optionally be spread
throughout the cycle to reduce ripple on the externally filtered PWM output. The PWM is
clocked by the output of Timer A9. The spreading function is implemented by dividing
each 1024-clock cycle into four quadrants of 256 clocks each. Within each quadrant, the
Pulse-Width Modulator uses the eight MSBs of each pulse-width register to select the base
width in each of the quadrants. This is the equivalent to dividing the contents of the pulsewidth register by four and using this value in each quadrant. To get the exact high time, the
Pulse-Width Modulator uses the two LSBs of the pulse-width register to modify the high
time in each quadrant according to Table F-3 below. The “n/4” term is the base count, and
is formed from the eight MSBs of the pulse-width register.
Table F-3. PWM Outputs
Pulse Width LSBs
1st
2nd
3rd
4th
00
n/4 + 1
n/4
n/4
n/4
01
n/4 + 1
n/4
n/4 + 1
n/4
10
n/4 + 1
n/4 + 1
n/4 + 1
n/4
11
n/4 + 1
n/4 + 1
n/4 + 1
n/4 + 1
The diagram below shows a PWM output for several different width values for both
modes of operation. Operation in the spread mode reduces the filtering requirements on
the PWM output in most cases.
n=255, normal
n=255, spread
(256 counts)
(64 counts)
(64 counts)
(64 counts)
(64 counts)
n=256, spread
(65 counts)
(64 counts)
(64 counts )
(64 counts)
n=257, spread
(65 counts)
(64 counts )
(65 counts)
(64 counts)
n=258, spread
(65 counts)
(65 counts)
(65 counts)
(65 counts)
n=259, spread
n=259, normal
(65 counts)
(65 counts)
(64 counts)
(65 counts)
(260 counts)
Figure F-1. PWM Outputs for Various Normal and Spread Modes
82
RabbitCore RCM3200
F.5 PWM Registers
There are no default values on reset for any of the PWM registers.
Table F-4. PWM Registers
PWM LSBs
Register
PWL0R
10001000 (0x88)
PWL1R
10001010 (0x8A)
PWL2R
10001100 (0x8C)
PWL3R
10001110 (0x8E)
Bit(s)
7:6
Address
Value
Write
5:1
Description
The least significant two bits for the Pulse Width Modulator count are
stored
These bits are ignored.
0
PWM MSB x
Bit(s)
7:0
User’s Manual
0
PWM output High for single block.
1
Spread PWM output throughout the cycle
Register
Address
PWM0R
Address = 10001001 (0x89)
PWM1R
Address = 10001011 (0x8B)
PWM2R
Address = 10001101 (0x8D)
PWM3R
Address = 10001111 (0x8F)
Value
write
Description
The most significant eight bits for the Pulse-Width Modulator count
are stored
With a count of n, the PWM output will be high for n +1 clocks out of
the 1024 clocks of the PWM counter.
83
F.6 Quadrature Decoder
The two-channel Quadrature Decoder accepts inputs via Parallel Port F from two external
optical incremental encoder modules. Each channel of the Quadrature Decoder accepts an
in-phase (I) and a quadrature-phase (Q) signal, and provides 8-bit counters to track shaft
rotation and provide interrupts when the count goes through the zero count in either direction. The Quadrature Decoder contains digital filters on the inputs to prevent false counts
and is clocked by the output of Timer A10. Each Quadrature Decoder channel accepts
inputs from either the upper nibble or lower nibble of Parallel Port F. The I signal is input
on an odd-numbered port bit, while the Q signal is input on an even-numbered port bit.
There is also a disable selection, which is guaranteed not to generate a count increment or
decrement on either entering or exiting the disable state. The operation of the counter as a
function of the I and Q inputs is shown below.
I input
Q input
Counter 00 01 02 03 04 05 06 07 08 07 06 05 04 03 02 01 00 FF
Interrupt
Figure F-2. Operation of Quadrature Decoder Counter
The Quadrature Decoders are clocked by the output of Timer A10, giving a maximum
clock rate of one-half of the peripheral clock rate. The time constant of Timer A10 must be
fast enough to sample the inputs properly. Both the I and Q inputs go through a digital filter that rejects pulses shorter than two clock periods wide. In addition, the clock rate must
be high enough that transitions on the I and Q inputs are sampled in different clock cycles.
The Input Capture (see the Rabbit 3000 Microprocessor Users Manual) may be used to
measure the pulse width on the I inputs because they come from the odd-numbered port
bits. The operation of the digital filter is shown below.
Peri Clock
Timer A10
Rejected
Accepted
84
RabbitCore RCM3200
The Quadrature Decoder generates an interrupt when the counter increments from 0x00 to
0x01 or when the counter decrements from 0x00 to 0xFF. Note that the status bits in the
QDCSR are set coincident with the interrupt, and the interrupt (and status bits) are cleared
by reading the QDCSR.
Table F-5. Quadrature Decoder Registers
Register Name
Quad Decode Control/Status
Register
Mnemonic
QDCSR
Bit
7
(rd-only)
Value
Address
10010000 (0x90)
Description
0
Quadrature Decoder 2 did not increment from 0xFF.
1
Quadrature Decoder 2 incremented from 0xFF to
0x00. This bit is cleared by a read of this register.
0
Quadrature Decoder 2 did not decrement from 0x00.
1
Quadrature Decoder 2 decremented from 0x00 to
0xFF. This bit is cleared by a read of this register
5
0
This bit always reads as zero.
4
(wr-only)
0
No effect on the Quadrature Decoder 2.
1
Reset Quadrature Decoder 2 to 0x00, without
causing an interrupt.
0
Quadrature Decoder 1 did not increment from 0xFF.
1
Quadrature Decoder 1 incremented from 0xFF to
0x00. This bit is cleared by a read of this register.
0
Quadrature Decoder 1 did not decrement from 0x00.
1
Quadrature Decoder 1 decremented from 0x00 to
0xFF. This bit is cleared by a read of this register.
0
This bit always reads as zero.
6
(rd-only)
3
(rd-only)
2
(rd-only)
1
Bit
0
(wr-only)
User’s Manual
Value
Description
0
No effect on the Quadrature Decoder 1.
1
Reset Quadrature Decoder 1 to 0x00, without
causing an interrupt.
85
Table F-5. Quadrature Decoder Registers (continued)
Register Name
Quad Decode Control
Register
Mnemonic
QDCR
Bit
Address = 10010001 (0x91)
Description
0x
Disable Quadrature Decoder 2 inputs. Writing a new
value to these bits will not cause Quadrature
Decoder 2 to increment or decrement.
10
Quadrature Decoder 2 inputs from Port F bits 3 and
2.
11
Quadrature Decoder 2 inputs from Port F bits 7 and
6.
5:4
xx
These bits are ignored.
3:2
0x
Disable Quadrature Decoder 1 inputs. Writing a new
value to these bits will not cause Quadrature
Decoder 1 to increment or decrement.
10
Quadrature Decoder 1 inputs from Port F bits 1 and
0.
11
Quadrature Decoder 1 inputs from Port F bits 5 and
4.
0
Quadrature Decoder interrupts are disabled.
1
Quadrature Decoder interrupt use Interrupt Priority
1.
10
Quadrature Decoder interrupt use Interrupt Priority
2.
11
Quadrature Decoder interrupt use Interrupt Priority
3.
QDC1R
Address = 10010100 (0x94)
(QDC2R)
Address = 10010110 (0x96)
7:6
1:0
Quad Decode Count Register
Bit(s)
7:0
86
Value
Address
Value
read
Description
The current value of the Quadrature Decoder
counter is reported.
RabbitCore RCM3200
NOTICE TO USERS
Z-WORLD PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFESUPPORT DEVICES OR SYSTEMS UNLESS A SPECIFIC WRITTEN AGREEMENT REGARDING
SUCH INTENDED USE IS ENTERED INTO BETWEEN THE CUSTOMER AND Z-WORLD PRIOR
TO USE. Life-support devices or systems are devices or systems intended for surgical implantation into the
body or to sustain life, and whose failure to perform, when properly used in accordance with instructions for
use provided in the labeling and user’s manual, can be reasonably expected to result in significant injury.
No complex software or hardware system is perfect. Bugs are always present in a system of any size. In
order to prevent danger to life or property, it is the responsibility of the system designer to incorporate
redundant protective mechanisms appropriate to the risk involved.
All Z-World products are 100 percent functionally tested. Additional testing may include visual quality control inspections or mechanical defects analyzer inspections. Specifications are based on characterization of
tested sample units rather than testing over temperature and voltage of each unit. Z-World products may
qualify components to operate within a range of parameters that is different from the manufacturer’s recommended range. This strategy is believed to be more economical and effective. Additional testing or burn-in
of an individual unit is available by special arrangement.
User’s Manual
87
88
RabbitCore RCM3200
INDEX
A
F
M
additional information
Getting Started manual ....... 3
online documentation .......... 3
auxiliary I/O bus ................... 11
features .................................... 1
flash memory addresses
user blocks ........................ 16
manuals ................................... 3
motor control option
quadrature decoder ............ 84
mounting instructions
LCD/keypad module ......... 46
B
battery backup
battery life ......................... 72
external battery connections .............................. 71
reset generator ................... 72
bus loading ............................ 28
C
clock doubler ........................ 15
conformal coating ................. 33
D
Development Kit
RCM3200 ............................ 2
digital I/O ................................ 6
I/O buffer sourcing and sinking limits ....................... 32
memory interface .............. 11
SMODE0 .................... 11, 13
SMODE1 .................... 11, 13
dimensions
LCD/keypad module ......... 41
LCD/keypad template ....... 44
Prototyping Board ............. 36
RCM3200 .......................... 24
Dynamic C ............................ 17
telephone-based technical support ................................ 21
upgrades and patches ........ 21
E
Ethernet port ......................... 12
pinout ................................ 12
exclusion zone ...................... 25
User’s Manual
I
I/O address assignments
LCD/keypad module ......... 45
I/O buffer sourcing and sinking
limits ............................. 32
J
jumper configurations ........... 34
JP1 (auxiliary I/O data bus) 34
JP2 (program execution
SRAM size) .................. 34
JP3 (flash memory size) .... 34
JP4 (flash memory bank select) ......................... 16, 34
JP5 (data SRAM size) ....... 34
jumper locations ................ 34
K
keypad template .................... 44
removing and inserting label ................................. 44
L
LCD/keypad module
bezel-mount installation .... 47
dimensions ........................ 41
header pinout ..................... 45
I/O address assignments .... 45
keypad template ................ 44
mounting instructions ....... 46
remote cable connection ... 49
removing and inserting keypad
label .............................. 44
sample programs ............... 70
voltage settings ................. 43
P
physical mounting ................. 27
pinout
Ethernet port ..................... 12
LCD/keypad module ......... 45
programming cable ........... 74
Prototyping Board ............. 38
RCM3200
alternate configurations
................................. 8, 75
RCM3200 headers .............. 6
power supplies
+3.3 V ............................... 71
battery backup ................... 71
optional +5 V output ......... 72
Program Mode ...................... 14
switching modes ............... 14
programming cable ......... 73, 77
DIAG connector ................ 74
pinout ................................ 74
programming port ................. 13
alternate pinout configurations .............................. 75
used as diagnostic port ...... 74
via motherboard ................ 13
Prototyping Board
adding RS-232 transceiver 39
dimensions ........................ 36
J6
pinout ............................ 78
pinout ................................ 38
power supply ..................... 37
prototyping area ................ 38
specifications .................... 37
PWM outputs ........................ 82
PWM registers ...................... 83
89
Q
quadrature decoder ................84
quadrature decoder registers .85
R
Rabbit 3000
data and clock delays .........30
Parallel Port F Registers ....79
Parallel Port F registers .....80
PWM outputs .....................82
PWM registers ...................83
quadrature decoder registers .................................85
spectrum spreader time delays
........................................30
Rabbit subsystems ...................7
Run Mode ..............................14
switching modes ................14
S
sample programs
LCD/keypad module .........70
serial communication ............12
serial ports .............................12
Ethernet port ......................12
programming port ..............13
software
auxiliary I/O bus ....11, 19, 50
board initialization .............18
brdInit ............................18
I/O drivers .........................19
keypad
keyConfig ......................67
keyGet ...........................68
keyInit ............................67
keypadDef .....................69
keyProcess .....................68
keyScan .........................69
keyUnget .......................68
90
LCD display
glBackLight ...................51
glBlankScreen ...............52
glBlock ..........................53
glBuffLock ....................59
glBuffUnlock .................59
glDispOnOff ..................51
glDown1 ........................62
glFillCircle .....................55
glFillPolygon .................55
glFillScreen ...................52
glFillVPolygon ..............54
glFontCharAddr .............56
glGetBrushType ............60
glGetPfStep ...................57
glHScroll .......................62
glInit ..............................51
glLeft1 ...........................61
glPlotCircle ....................55
glPlotDot .......................60
glPlotLine ......................60
glPlotPolygon ................54
glPlotVPolygon .............53
glPrintf ...........................58
glPutChar .......................58
glPutFont .......................57
glRight1 .........................61
glSetBrushType .............59
glSetContrast .................52
glSetPfStep ....................57
glSwap ...........................59
glUp1 .............................61
glVScroll .......................63
glXFontInit ....................56
glXPutBitmap ................63
glXPutFastmap ..............64
TextCursorLocation .......65
TextGotoXY ..................65
TextPrintf .......................66
TextPutChar ...................65
TextWindowFrame ........64
LCD/keypad module
ledOut ............................50
LCD/keypad module LEDs 50
libraries
PACKET.LIB ................19
RCM3200.LIB ...............50
RCM32xx.LIB ...............18
RS232.LIB .....................19
TCP/IP ...........................19
readUserBlock ...................16
sample programs ...............20
RCM3200 ......................20
TCP/IP ...........................20
serial communication drivers ..................................19
TCP/IP drivers ...................19
writeUserBlock .................16
specifications .........................23
bus loading ........................28
digital I/O buffer sourcing and
sinking limits .................32
dimensions .........................24
electrical, mechanical, and environmental ...................26
exclusion zone ...................25
header footprint .................27
headers ...............................27
LCD/keypad module
dimensions .....................41
electrical ........................42
mechanical .....................42
temperature ....................42
physical mounting .............27
Prototyping Board .............37
Rabbit 3000 DC characteristics .................................31
Rabbit 3000 timing diagram ..
29
relative pin 1 locations ......27
spectrum spreader .................30
subsystems
digital inputs and outputs ....6
switching modes ....................14
RabbitCore RCM3200
SCHEMATICS
090-0152 RCM3200 Schematic
www.rabbitsemiconductor.com/documentation/schemat/090-0152.pdf
090-0137 Prototyping Board Schematic
www.rabbitsemiconductor.com/documentation/schemat/090-0137.pdf
090-0156 LCD/Keypad Module Schematic
www.rabbitsemiconductor.com/documentation/schemat/090-0156.pdf
090-0128 Programming Cable Schematic
www.rabbitsemiconductor.com/documentation/schemat/090-0128.pdf
The schematics included with the printed manual were the latest revisions available at the
time the manual was last revised. The online versions of the manual contain links to the
latest revised schematic on the Web site. You may also use the URL information provided
above to access the latest schematics directly.
User’s Manual
91