ETC D322RP

Model Selection Guide
Model
Number
D301RP
D302RP
D303RP
D304RP
D305RP
D311RP
D312RP
D313RP
D314RP
D315RP
D321RP
D322RP
D323RP
D324RP
D325RP
Notes:
Input
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load
5
4.5 - 5.5
895
90
5
4.5 - 5.5
895
90
5
4.5 - 5.5
833
90
5
4.5 - 5.5
833
90
5
4.5 - 5.5
857
90
12
10.8 - 13.2
373
60
12
10.8 - 13.2
373
60
12
10.8 - 13.2
347
60
12
10.8 - 13.2
347
60
12
10.8 - 13.2
357
60
24
21.6 - 26.4
192
30
24
21.6 - 26.4
192
30
24
21.6 - 26.4
179
30
24
21.6 - 26.4
179
30
24
21.6 - 26.4
174
30
1. Output load regulation is specified for a load change
of 20% to 100%.
2. When measuring output ripple, it is recommended
that an external 0.33 μF ceramic capacitor be placed
from the +Vout pin to the -Vout pin.
3. Operation at no-load will not damage these units.
However, they may not meet all specifications.
4. These do not require external components to operate,
but the use of a low ESR capacitor (approximately
10 uF, ESR <1.0Ω at 100 kHz) mounted close to the
converter input pins is recommended.
5. It is recommended that a fuse be used on the input of
a power supply for protection. See the table above for
the correct rating.
Capacitive
Load
Voltage
(VDC)
5.0
9.0
12.0
15.0
24.0
5.0
9.0
12.0
15.0
24.0
5.0
9.0
12.0
15.0
24.0
Output
Current
(mA, Max)
600.0
333.0
250.0
200.0
125.0
600.0
333.0
250.0
200.0
125.0
600.0
333.0
250.0
200.0
125.0
Current
(mA, Min)
60.0
33.0
25.0
20.0
12.5
60.0
33.0
25.0
20.0
12.5
60.0
33.0
25.0
20.0
12.5
Efficiency
(%, Typ)
67
67
72
72
70
67
67
72
72
70
65
65
70
70
72
Fuse Rating
Slow-Blow
(mA)
1,500
1,500
1,500
1,500
1,500
700
700
700
700
700
350
350
350
350
350
Derating Curve
Pin Connections
μF Max
470
Pin
Function
1
+Vin
2
NC
3
NC
9
NC
10
-Vout
11
+Vout
12
-Vin
Mechanical Dimensions
NC: No Connection
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
■
TEL: (781) 344-8226
■
FAX: (781) 344-8481
■
E-Mail: [email protected]