ETC D205RPI

MicroPower
Direct
2W, High Isolation, SIP
Regulated, Short Circuit Protected
DC/DC Converters
■
D200RPI Series
■
Key Features
■
Miniature SIP Package
Short Circuit Protected
1.5 MH MTBF
■
■
■
2.0W Output Power
High Isolation
Low Cost
Electrical Specifications
Specifications typical @ +25ºC with nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
5 VDC Input
Input Voltage Range
Min.
Typ.
Max.
4.5
5.0
5.5
12 VDC Input
10.8
12.0
13.2
24 VDC Input
21.6
24.0
26.4
Input Filter
Units
VDC
π (Pi) Filter
Reverse Polarity Input Current
0.3
A
Max.
Units
±2.0
%
%
Output
Parameter
Conditions
Min.
Typ.
Output Voltage Accuracy
Line Regulation
For Vin Min to Max
±0.5
Load Regulation
Iout = 10% to 100%
±0.5
%
75
mV P - P
Ripple & Noise (20 MHz)
Output Power Protection
120
%
Temperature Coefficient
Output Short Circuit
±0.02
%/ºC
Max.
Units
Continuous
General
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Min.
60 Seconds
3,000
500 VDC
1,000
Typ.
VDC
MΩ
100 kHz, 1V
Switching Frequency
60
pF
40
kHz
Environmental
Parameter
Min.
Typ.
Max.
Units
Operating Temperature Range
Conditions
Ambient
-40
+25
+71
ºC
Operating Temperature Range
Case
-40
+85
ºC
-40
+125
ºC
95
%
Storage Temperature Range
Cooling
Free Air Convection
Humidity
RH, Non-condensing
Physical
Case Size (5V & 12V Models)
1.26 x 0.32 x 0.55 Inches (32.0 x 8.0 x 14.0 mm)
Case Material
Non-Conductive Black Plastic
Weight (5V & 12V Input Models)
0.17 Oz (4.8g)
Reliability Specifications
Parameter
Conditions
MTBF
Min.
MIL HDBK 217F, 25ºC, Gnd Benign
Typ.
Max.
1.5
Units
MHours
Absolute Maximum Ratings
Parameter
Conditions
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Min.
Typ.
Max.
5 VDC Input
-0.7
9.0
12 VDC Input
-0.7
18.0
24 VDC Input
-0.7
30.0
Units
VDC
1.5 mm From Case For 10 Sec
260
ºC
All Models
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
MicroPower Direct
● TEL: (781) 344-8226 ● FAX: (781) 344-8481 ● E-Mail: [email protected] ● WEB: www/micropowerdirect.com
Model Selection Guide
Input
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load
5
4.5 - 5.5
606
80
5
4.5 - 5.5
606
80
5
4.5 - 5.5
571
80
5
4.5 - 5.5
571
80
5
4.5 - 5.5
588
80
12
10.8 - 13.2
253
45
12
10.8 - 13.2
253
45
12
10.8 - 13.2
238
45
12
10.8 - 13.2
238
45
12
10.8 - 13.2
246
45
24
21.6 - 26.4
130
25
24
21.6 - 26.4
130
25
24
21.6 - 26.4
122
25
24
21.6 - 26.4
122
25
24
21.6 - 26.4
118
25
D201RPI
D202RPI
D203RPI
D204RPI
D205RPI
D211RPI
D212RPI
D213RPI
D214RPI
D215RPI
D221RPI
D222RPI
D223RPI
D224RPI
D225RPI
Notes:
1. These units do not require external comonents to operate, but the use of an input
capacitor (10 µF) may enhance performance in some applications. An output
capacitor (4.7 µF to 10 µF) may be used to
reduce ripple.
Capacitive Load
Voltage
(VDC)
5.0
9.0
12.0
15.0
24.0
5.0
9.0
12.0
15.0
24.0
5.0
9.0
12.0
15.0
24.0
Output
Current
(mA, Max)
400.0
222.0
167.0
133.0
83.0
400.0
222.0
167.0
133.0
83.0
400.0
222.0
167.0
133.0
83.0
Current
(mA, Min)
40.0
22.0
17.0
13.0
10.0
40.0
22.0
17.0
13.0
10.0
40.0
22.0
17.0
13.0
10.0
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
200
200
200
200
200
Efficiency
(%, Typ)
66
66
70
70
68
66
66
70
70
68
64
64
68
68
70
Derating Curve
100
80
Output Power %
Model
Number
μF Max
60
40
20
470
0
-25
-10
0
5
10
15
20
30
40
50
60
70
80
85
Ambient Temperature 1C
Pin Connections
Pin
Function
1
+Vin
2
-Vin
3
NC
9
NC
10
-Vout
11
+Vout
12
NC
Mechanical Dimensions
5.5
(14.00)
Side
0.02
(0.50)
NC: No Connection
0.10
(2.5)
0.60 (15.24)
0.08
(2.13)
1.26 (32.00)
0.03
(0.68)
Notes: All dimensions are typical in inches
0.02
(0.50)
0.01
(0.30)
(mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation
on the side of the unit
0.32
(8.00)
Bottom
1
2
3
MicroPower
Direct
9
10
11
12
0.13
(3.40)
232 Tosca Drive, Stoughton, MA 02072
www.micropowerdirect.com
[email protected]
phone: (781) 344 - 8226 • fax: (781) 344 - 8481