ES2A THRU ES2J 2.0 AMPS. Super Fast Surface Mount Rectifiers Voltage Range 50 to 600 Volts Current 2.0 Amperes SMB/DO-214AA Features Glass passivated junction chip For surface mounted application Low profile package Built-in strain relief Ideal for automated placement Easy pick and place Superfast recovery time for high efficiency Glass passivated chip junction High temperature soldering: O 260 C/10 seconds at terminals Plastic material used carries Underwriters Laboratory Classification 94V-O .082(2.08) .076(1.93) .147(3.73) .137(3.48) .187(4.75) .167(4.25) .012(.31) .006(.15) .103(2.61) .078(1.99) Mechanical Data .012(.31) .006(.15) .056(1.41) .035(0.90) Cases: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packing: 12mm tape per E1A STD RS-481 Weight: 0.093 gram .008(.20) .004(.10) .208(5.28) .200(5.08) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol ES ES ES Type Number 2A 2B 2C Maximum Recurrent Peak Reverse 50 100 150 VRRM Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 2.0A Maximum DC Reverse Current @TA =25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Maximum Thermal Resistance (Note 3) VRMS VDC 35 50 70 100 105 150 ES 2D 200 ES 2F 300 ES 2G 400 ES 2H 500 ES 2J 600 Units 140 200 210 300 280 400 350 500 420 600 V V V I(AV) 2.0 A IFSM 50 A 0.95 VF Trr Cj Operating Temperature Range Storage Temperature Range TSTG 1.7 10 350 35 IR RθJA RθJL TJ 1.3 25 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Units Mounted on P.C.B. 0.4 x 0.4" (10 x 10mm) Pad Areas - 168 - uA uA nS 20 75 20 -55 to +150 -55 to + 150 V pF ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (ES2A THRU ES2J) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 60 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 3.0 RESISTIVE OR INDUCTIVE LOAD 0.4X0.4"(10X10mm) COPPER PAD AREAS 2.0 1.0 0 80 90 100 110 120 130 140 8.3ms Single Half Sine Wave o (JEDEC Method) at TL=120 C 50 40 30 20 10 0 150 NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 60 100 10 1 o LEAD TEMPERATURE. ( C) FIG.4- TYPICAL REVERSE CHARACTERISTICS 1000 0 -G 2A -D INSTANTANEOUS REVERSE CURRENT. ( A) 10 -J ES 2F ES 2H 1 ES INSTANTANEOUS FORWARD CURRENT. (A) Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.1 0.01 0.4 0.8 1.0 1.2 1.4 1.6 10 Tj=85 0C 1 Tj=25 0C 0.1 0 1.8 FIG.5- TYPICAL JUNCTION CAPACITANCE Tj=25 0C f=1.0MHz Vsig=50mVp-p 50 40 ES 30 20 ES 2F 2A -D -J 10 0 1 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 60 JUNCTION CAPACITANCE.(pF) Tj=125 0C 0.01 0.6 FORWARD VOLTAGE. (V) 0 100 10 100 REVERSE VOLTAGE. (V) - 169 -