RSFAL THRU RSFML 0.5 AMP. Surface Mount Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 0.5 Ampere Sub SMA 5 0.15(3.8) O 0.00~0.004 0.047(1.2) Cases: Sub SMA plastic case Terminals: Solder plated Polarity: Indicated by cathode band Packing: 12mm tape per E1A STD RS-481 Weight: 15mg O 0.134(3.4) (0.00~0.10) 0.056(1.43) 5 A Mechanical Data 0.048(1.23) 0.075(1.9) 0.106(2.7) 0.01(0.23) 0.114(2.9) 0.007(0.17) For surface mounted application Glass passivated junction chip High temperature metallurgically bonded construction Plastic material used carries Underwriters Laboratory Classification 94V-O Fast switching for high efficiency High temperature soldering: 260℃/ 10 seconds at terminals 0.031(0.8) 0.067(1.7) Features DETAIL "A", SCALE=20/1 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol RSF RSF RSF RSF RSF RSF RSF Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage V RRM V RMS V DC Marking Code ( Note 4 ) Maximum Average Forward Rectified Current O See Fig. 1 @T L=55 C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Max. Full Load Reverse Current, Full cycle Average T A =55℃ Maximum Instantaneous Forward Voltage @ 0.5A Maximum DC Reverse Current @ T A =25℃ at Rated DC Blocking Voltage @ T A=125℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) Units AL 50 BL 100 DL 200 GL 400 JL 600 KL 800 ML 1000 35 70 140 280 420 560 700 V 50 100 200 400 600 800 1000 V V FALYM FBLYM FDLYM FGLYM FJLYM FKLYM FMLYM I(AV) 0.5 A IFSM 10 A IR 30 uA VF 1.3 V IR 5 50 uA uA nS Trr 150 Cj 250 4.0 150 32 -55 to +150 -55 to +150 R θ JA R θ JL TJ T STG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR =1.0A, IRR =0.25A 2. Measured at 1 MHz and Applied V R =4.0 Volts 3. Measured on P.C.Board with 0.2” x 0.2” (5mm x 5mm) Copper Pad Areas. 4. FALYM: F=0.5A, A=50V, L-Low Profile, Y-Year Code, M-Month Code. Operating Temperature Range Storage Temperature Range - 384 - 500 pF ℃/W ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (RSFAL THRU RSFML) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 0.5 0.4 0.3 RESISTIVE OR INDUCTIVE LOAD 0.2 0.1 0 P.C.B. MOUNTED ON 0.2X0.2" (5.0X5.0mm) COPPER PAD AREAS 0 20 40 60 80 100 120 140 160 FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 30 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 0.6 TL=90OC 8.3ms Single Half Sine Wave JEDEC Method 25 20 15 10 0 180 1 10 o LEAD TEMPERATURE. ( C) FIG.4- TYPICAL REVERSE CHARACTERISTICS FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 30 30 10 10 INSTANTANEOUS REVERSE CURRENT. ( A) INSTANTANEOUS FORWARD CURRENT. (A) 100 NUMBER OF CYCLES AT 60Hz 1 Tj=25 0C 0.1 Tj=100 0C 1 0.1 Tj=25 0C 0.01 Pulse Width=300 s 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.001 1.8 FORWARD VOLTAGE. (V) FIG.5- TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE.(pF) Tj=25 0C f=1.0MHz Vsig=50mVp-p 1 10 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 10 0 0 100 REVERSE VOLTAGE. (V) - 385 - 100