IDEA IBHC0358

IBHC0358
Page 1 of 6
PART NO.
IBHC0358
Chip
Material
Emitted Color
InGaN
Blue
Lens Color
Water Clear
* Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise.
IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304
0901a
IBHC0358
Page 2 of 6
Absolute Maximum Ratings at Ta = 25 ˚C
Parameter
Symbol
Rating
Units
Forward Current
IF
25
mA
Reverse Voltage
VR
5
V
Operating Temperature
Topr
-40 to +85
˚C
Storage Temperature
Tstg
-40 to +90
˚C
Electrostatic Discharge
ESD
150
V
Power Dissipation
Pd
110
mW
Peak Forward Current
(Duty 1/10 @ 1KHz)
IFP
100
mA
Soldering Temperature
Tsol
Reflow Soldering: 260°C for 10 sec.
Hand Soldering: 350°C for 3 sec.
Electronic Optical Characteristics (Ta = 25 ˚C)
Parameter
Symbol
Min.
Typ.
Max.
Units
Luminous Intensity
IV
45
—
90
mcd
Viewing Angle
2θ1/2
—
60
—
deg
Peak
Wavelength
λp
—
468
—
nm
Dominant
Wavelength
λd
470
—
475
nm
Spectrum Radiation
Bandwidth
Δλ
—
25
—
nm
Forward Voltage
VF
2.60
—
3.00
V
Reverse Current
IR
—
—
50
μA
Condition
IF = 5 mA
VR = 5 V
Notes:
1. Tolerance of Luminous Intensity: ±11%
2. Tolerance of Dominant Wavelength: ±1 nm
3. Tolerance of Forward Voltage: ±0.05 V
* Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise.
IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304
0901a
IBHC0358
Page 3 of 6
Bin Range of Dominant Wavelength
Bin
Min
Max
Unit
Condition
Y
470
475
nm
IF = 5 mA
Bin Range of Luminous Intensity
Bin
Min
Max
P1
45
57
P2
57
72
Q1
72
90
Unit
Condition
mcd
IF = 5 mA
Bin Range of Forward Voltage
Group
T
Min
Max
2.60
2.70
2.70
2.80
2.80
2.90
2.90
3.00
Unit
Condition
V
IF = 5 mA
Notes:
1. Tolerance of Luminous Intensity: ±11%
2. Tolerance of Dominant Wavelength: ±1 nm
3. Tolerance of Forward Voltage: ±0.05 V
* Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise.
IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304
0901a
IBHC0358
Page 4 of 6
Typical Electro-Optical Characteristics Curves:
* Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise.
IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304
0901a
IBHC0358
Page 5 of 6
Reel Dimensions:
Carrier Tape Dimensions:
* Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise.
IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304
0901a
IBHC0358
Page 6 of 6
Precautions for Use
1. Over-current prevention:
A series resistor must be used for protection against over-current. Since slight voltage shifts
can cause large current changes and possibly damage the LED.
2. Storage:
2.1. Store the LEDs in the sealed moisture proof bag until ready to use.
2.2. The storage conditions should be below 30°C and 90% RH or less.
2.3. Unused portions of LEDs may be stored in moisture proof packages for up to 1 year if
kept under 30°C and at no more than 60% RH.
2.4. If there is evidence of moisture absorption or if the LEDs have been stored for a long
time, bake the LEDs at 60°C ± 5°C for 24 hours prior to using.
3. Reflow Soldering Conditions:
3.1. Pb-free solder temperature profile (see figure):
3.2. Reflow solder no more than two times and must include time interval for the board to
cool.
3.3. When soldering, do not put stress on the LEDs during heating.
3.4. After soldering, do not warp the circuit board.
4. Hand Soldering:
Use a low wattage soldering iron (below 25 watts) with a tip temperature no more than
350°C for 3 sec or less on one terminal. Wait at least two seconds before soldering the next
terminal to avoid overheating the LED and damaging it.
5. Avoid reworking a soldered LED. It is best to simply replace it with a new part.
* Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise.
IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304
0901a