JRGC0128 Page 1 of 6 PART NO. JRGC0128 Chip Material SUR AlGaInP SYG AlGaInP Emitted Color Red Yellow Green Lens Color Water Clear * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 1004 JRGC0128 Page 2 of 6 Absolute Maximum Ratings at Ta = 25 ˚C Parameter Symbol Forward Current SUR IF SYG Rating Units 25 mA Reverse Voltage VR 5 V Operating Temperature Topr -40 to +85 ˚C Storage Temperature Tstg -40 to +90 ˚C Electrostatic Discharge (HBM) ESD 2000 V 60 mW 60 mA Power Dissipation Pd Peak Forward Current (Duty 1/10 @ 1KHz) IFP Soldering Temperature SUR SYG SUR SYG Electronic Optical Characteristics (Ta = 25 ˚C) Parameter Symbol Min. Luminous Intensity Viewing Angle IV λp Dominant Wavelength λd Spectrum Radiation Bandwidth Δλ Forward Voltage VF Typ. Max. — SUR 36 54 SYG 21 28 — 120 — SUR — 632 — SYG — 575 — SUR — 624 — SYG — 573 — SUR — 20 — SYG — 20 — SUR 1.7 2.0 2.4 SYG 1.7 2.0 2.4 — — 10 2θ1/2 Peak Wavelength Reverse Current Reflow Soldering: 260°C for 10 sec. Hand Soldering: 350°C for 3 sec. Tsol IR Units Condition mcd IF = 20 mA deg IF = 20 mA nm IF = 20 mA nm IF = 20 mA nm IF = 20 mA V IF = 20 mA μA VR = 5 V * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 1004 JRGC0128 Page 3 of 6 Typical Electro-Optical Characteristics Curves: SUR * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 1004 JRGC0128 Page 4 of 6 Typical Electro-Optical Characteristics Curves: SYG * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 1004 JRGC0128 Page 5 of 6 Reel Dimensions: Carrier Tape Dimensions: * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 1004 JRGC0128 Page 6 of 6 Precautions for Use 1. Over-current prevention: A series resistor must be used for protection against over-current. Since slight voltage shifts can cause large current changes and possibly damage the LED. Storage: Store the LEDs in the sealed moisture proof bag until ready to use. The storage conditions should be below 30°C and 90% RH or less. Unused portions of LEDs may be stored in moisture proof packages for up to 1 year if kept under 30°C and at no more than 60% RH. If there is evidence of moisture absorption or if the LEDs have been stored for a long time, bake the LEDs at 60°C ± 5°C for 24 hours prior to using. Reflow Soldering Conditions: Pb-free solder temperature profile (see figure): Reflow solder no more than two times and must include time interval for the board to cool. When soldering, do not put stress on the LEDs during heating. After soldering, do not warp the circuit board. Hand Soldering: Use a low wattage soldering iron (below 25 watts) with a tip temperature no more than 350°C for 3 sec or less on one terminal. Wait at least two seconds before soldering the next terminal to avoid overheating the LED and damaging it. Avoid reworking a soldered LED. It is best to simply replace it with a new part. * Specifications subject to change without notice. Dimensions are in mm ±0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 1004