TECHNICAL DATA IL317 THREE-TERMINAL ADJUSTABLE OUTPUT POSITIVE VOLTAGE REGULATORS The IL317 is adjustable 3-terminal positive voltage regulator capable of supplying in excess of 1.5 A over an output voltage range of 1.2 V to 37 V. These voltage regulator is exceptionally easy to use and require only two external resistors to set the output voltage. Further, it employ internal current limiting, thermal shutdown and safe area compensation, making them essentially blow-out proof. The IL317 serve a wide variety of applications to make a programmable output regulator, or by connecting a fixed resistor between the adjustment and output, the IL317 series can be used as a precision current requlator. · Output Current in Excess of 1.5 Ampere · Output Adjustable between 1.2 V and 37 V · Internal Thermal Overload Protection · Internal Short - Circuit Current Limiting Constant with Temperature · Output Transistor Safe-Area Compensation · Floating Operation for High Voltage Applications · Standard 3-lead Transistor Packages · Eliminates Stocking Many Fixed Standard application Vin Vout IL317 R1 Сin* 0.1mF Сo** 1mF Adjust R2 * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability ; however, is does improve transient response. . V (1 + Vout = 125 Since IADJ is controlled to less then 100 mA, the error associated with this term is negligible in most applications. Maximum ratings Rating Input - Output Voltage Differential Power Dissipation and Thermal Characteristics Operating Junction Temperature Rang Storage Junction Temperature Rang R2 )+ * R2 R1 I ADJ Symbol Vi - Vo Value 40 Unit Vdc PD TJ Tstg Internally Limited -0 to +150 -65 to +150 °C °C Rev. 00 IL317 Electrical characteristics (Vi-Vo= 5.0V, Io = 0.5 A, TJ = Tlow to Thigh (see Note 1); Imax = 1.5 A and Pmax = 20 W unless otherwise noted) Characteristic Line Regulation (TA=+25°C) 3.0V £ Vi - Vo £40 V Load Regulation(TJ=+25°C) 10mA£Io£Imax, Vin £5V Vin³5 V Thermal Regulation (TA=+25°C) 20 ms Pulse Adjustment Pin Current Adjustment Pin Current Change 2.5 £ Vi - Vo £ 40 V 10mA £IL£ Imax, PD £ Pmax Reference Voltage (Note 4) 3.0 £ Vi - Vo £ 40 V 10mA £IL£ Imax, PD £ Pmax Line Regulation (Note 3) 3.0 V £ Vi - Vo £40 V Load Regulation (Note 3) 10mA£Io£Imax, Vin £5V Vin³5 V Temperature Stability (Tlow £ Tj £ Ttigh) Minimum Load Current to Maintain Regulation (Vi - Vo = 40 V) Maximum Output Current Vi - Vo£ 15 V , P £ 20 W Vi - Vo = 40 V, P £20W, TA=+25°C RMS Nose , % of Vo TA=+25°C, 10 Hz £ f £ 10 kHz Ripple Rejection, Vo = 10 V, f = 120 Hz (Note 5) Without Cadj Cadj = 10 mF Long-Term Stability, Tj = Thigh (Note 6) TA=+25°C for Endpoint Measurements Thermal Resistance Junction to Case Symbol Regline Min - Typ 0.01 Max 0.04 Unit %/V - - 5.0 0.1 0.03 25 0.5 0.07 mV %/Vo %/W IAdj DIAdj - 50 0.2 100 5.0 mA mA Vref 1.2 1.25 1.3 V Regline - 0.02 0.07 %/V - 20 0.3 0.7 3.5 70 1.5 10 mV %/V 1.5 0.15 - 2.2 0.4 0.003 - Regload Regload Ts ILmin Imax N mA A RR %/Vo dB S 66 - 65 80 0.3 1.0 RqJC - 5.0 - %/1.0 k Hrs. °C/W Notes: (1) Tlow = 0 °C , Thigh = +125 °C (2) Imax = 0.5 A , Pmax (3) Load and line regulation are specified at constant junction tempereture. Changes in Vo due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. (4) Selected devices with tightened tolerance reference voltage available. (5) Cadj , when used, connected between the adjustment pin and ground. (6) Since Long - Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average stability from lot to lot. Rev. 00 IL317 TO-220AB PKG OUTLINE DIMENSIONS Rev. 00 IL317 Rev. 00 IL317 TO-263-3L PKG OUTLINE DIMENSIONS Rev. 00