TECHNICAL DATA Low Power Ground Fault Interrupter IL4145A The IL4145AN is a low power controller for AC outlet ground fault interrupters. These devices detect hazardous grounding conditions, such as equipment (connected to opposite phases of the AC line) in contact with a pool of water and open circuits the line before a harmful or lethal shock occurs. Contained internally are a 26V zener shunt regulator, an op amp, and an SCR driver. With the addition of two sense transformers, a bridge rectifier, an SCR, a relay, and a few additional components, the IL4145AN will detect and protect against both hot wire to ground and neutral wire to ground faults. The simple layout and conventional design ensure ease of application and long-term reliability. ORDERING INFORMATION IL4145AN Plastic DIP IL4145AD SOIC TA = -35° to 85° C for all packages. No potentiomenter required Direct interface to SCR Supply voltage derived from AC line – 26V shunt Adjustable sensitivity Grounded neutral fault detection Meets U.L. 943 standards 450 µA quiescent current Ideal for 120 V or 220 V systems BLOCK DIAGRAM VFB PIN ASSIGNMENT + R1 10K +Input Op Amp Output R2 10K VREF (+13V) 6.5 V 6.5 V + 6.5 V 6.5 V +VS (+26V) VFB 1 8 NC +Input 2 7 Op Amp Output VREF 3 6 +VS GND 4 5 SCR Trigger + Ground SCR Trigger R3 4.7K ABSOLUTE MAXIMUM RATINGS Symbol ICC PD Tstg Topr TJ TL PD Parameter Supply Current Internal Power Dissipation Storage Temperature Range Operating Temperature Range Junction Temperature Lead Temperature TA< 50°C For TA> 50°C Derate at Value 18 500 -65 to +150 -35 to +85 125 125 450 6 Unit mA mW °C °C °C °C mW mW/°C IL4145A ELECTRICAL CHARACTERISTICS (IS= 1.5 mA and TA= +25°C) Symbol VOH Parameter Detector Reference Voltage Test Condition Min Max Unit Pin 7 to Pin 3 6.8 8.1 ±V Shunt Regulator +VS Zener Voltage Pin 6 to Pin 4 25 29.2 V VREF Reference Voltage Pin 3 to Pin 4 12.5 14.6 V IS Quiescent Current +VS = 24 V 750 µA Operational Amplifier VIO Offset Voltage Pin 2 to Pin 3 -3.0 +3.0 mV VD +Output Voltage Swing Pin 7 to Pin 3 6.8 8.1 V VOL –Output Voltage Swing Pin 7 to Pin 3 -13.5 -9.5 V IOH +Output Source Current Pin 7 to Pin 3 ⎪-450⎪ ⎪-850⎪ µA IOL –Output Source Current Pin 7 to Pin 3 800 1200 µA Gain Bandwidth Product 1.0 R1 F = 50 KHz IS = 0 mA Pin 1 to Pin 3 8 12 kΩ R2 Pin 2 to Pin 3 8 12 kΩ Pin 5 to Pin 4 Pin 5 to Pin 4 3.5 5.9 kΩ BW Resistors R1 R2 R3 R3 SCR Trigger Voltage VON Detector On VOFF MHz 1.5 Detector Off V 0 10 mV Min Max Unit Pin 7 to Pin 3 6.5 8.3 ±V ELECTRICAL CHARACTERISTICS (IS= 1.5 mA and -35°C ≤ TA ≤ +85°C) Symbol VOH Parameter Detector Reference Voltage Test Condition Shunt Regulator +VS Zener Voltage Pin 6 to Pin 4 24 30 V VREF Reference Voltage Pin 3 to Pin 4 12 15 V IS Quiescent Current +VS = 23 V 800 µA Operational Amplifier VIO Offset Voltage Pin 2 to Pin 3 -5.0 +5.0 mV VD +Output Voltage Swing Pin 7 to Pin 3 6.5 8.3 V –Output Voltage Swing -14 -9 V R1 Pin 7 to Pin 3 IS = 0 mA Pin 1 to Pin 3 7.5 12.5 kΩ R2 Pin 2 to Pin 3 7.5 12.5 kΩ Pin 5 to Pin 4 Pin 5 to Pin 4 3.5 5.9 kΩ VOL Resistors R1 R2 R3 R3 SCR Trigger Voltage VON Detector On VOFF Detector Off 1.3 0 V 50 mV IL4145A Principles of Operation The 26V shunt regulator voltage generated by the string of zener diodes is divided into three reference voltages: 3/4 VS , 1/2 VS , and 1/4 VS . VREF is at 1/2VS and is used as a reference to create an artifical ground of +13V at the op amp noninverting input. Figure 1 shows a three-wire 120V AC outlet GFI application using an IL4145AN. Fault signals from the sense transformer are AC coupled into the input and are amplified according to the following equation: V7 = RSENSE x ISENSE/N Where V7 is the RMS voltage at pin 7 relative to pin 3, RSENSE is the value of the feedback resistor connected from pin 7 to pin 1, ISENSE is the fault current in amps RMS and N is the turns ratio of the transformer. When V7 exceeds plus or minus 7.2V relative to pin 3 the SCR Trigger output will go high and fire the external SCR. The formula for V7 is approximate because it does not include the sense transformer characteristics. Grounded neutral fault detection is accomplished when a short or fault closes a magnetic path between the sense transformer and the grounded neutral transformer. The resultant AC coupling closes a positive feedback path around the op amp, and therefore the op amp oscillates. When the peaks of the oscillation voltage exceed the SCR trigger comparator thresholds, the SCR output will go high. Adjust RSENSE upward until the SCR activates. A fixed resistor can be used for RSENSE, since the resultant ±15% variation in sensitivity will meet UL’s 943 4-6mA specification window. The roll-off frequency is greater than the grounded neutral fault oscillation frequency, in order to preserve loop gain for oscillation (which is determined by the inductance of the 200:1 transformer and C4). The senstivity to grounded neutral faults is adjusted by changing the frequency of oscillation. Increasing the frequency reduces the sensitivity by reducing the loop gain of the positive feedback circuit. As frequency increases, the signal becomes attenuated and the loop gain decreases. With the values shown the circuit will detect a grounded neutral fault having resistance of 2Ω or less. The input to the op amp are protected from overvoltage by back-toback diodes. SCR Driver The SCR used must have a high dV/dt rating to ensure that line noise (generated by noisy appliances such as a drill motor) does not falsely trigger the SCR. Also, the SCR must have a gate drive requirement of less than 200µA. CF is a noise filter capacitor that prevents narrow pulses from firing the SCR. The relay solenoid used should have a 3ms or less response time in order to meet the UL 943 timing requirement. Sense Transformers and Cores Shunt Regulator RLINE limits the current into the shunt regulator; 220V applications will require substituting a 47kΩ 2W resistor. In addition to supplying power to the IC, the s h u n t regulator creates internal reference voltages (see above). The sense and grounded neutral transformer cores are usually fabricated using high permeability laminated steel rings. Their single turn primary is created by passing the line and neutral wires through the center of its core. The secondary is usually from 200 to 1500 turns. Operational Amplifier Two-Wire Application Circuit RSENSE therefore RSENSE, current (a standard). is a feedback resistor that sets gain and sensitivity to normal faults. To adjust follow this procedure: apply the desired fault difference in current of 5mA is the UL 943 Figure 2 shows the diagram of a 2-wire 120V AC outlet GFI circuit using an IL4145AN. This circuit is not designed to detect grounded neutral faults. Thus, the grounded neutral transformer and capacitors C3 and C4 of Figure 1 are not used. IL4145A Press To Test RTEST 15K MOV Ground Neutral Transformer Sense Transformer 1000:1 Line Latching Contacts K1 200:1 Hot Neutral RSENSE 1M* C1 10µF Load IL4145AN VFB Op Amp Output VREF(+13V) GND C3 0.01 µF Solenoid C4 0.03 µF +VS SCR Trigger DB1 1N4004 (4) RLINE 24 K Q1 ON Semi MCR100-6 CF 2.2µF C2 0.01µF * Value depends on transformer characteristics. Figure 1. GFI Application Circuit (Three-Wire Outlet) IL4145A Press To Test RTEST 15K MOV Sense Transformer 1000:1 Line Latching Contacts K1 Hot Neutral RSENSE 1M* C1 10µF Load IL4145AN VFB Op Amp Output VREF(+13V) GND Solenoid +VS SCR Trigger DB1 1N4004 (4) RLINE 24 K Q1 Tagi X0103DA CF 2.2µF C2 0.01µF * Value depends on transformer characteristics. Figure 2. GFI Application Circuit (Two-Wire Outlet) +Input (2) VFB (1) Q21 C2 10 pF Q22 (-) R1 10K Q4 Q1 R4 50K Q6 Q3 R10 6K Q5 Q2 R5 50K (+) Q7 R2 10K Q8 4 pF C1 Q9 Q23 Q11 Q10 R6 450 R14 1.3K Q12 Q14 (7) Z1 5.6V Q15 R3 4.7K R13 30K Op Amp Output R9 39K Q13 R7 250K Q17 6.5V (5) SCR Trigger Sbstrate R12 7.2K Q16 Q18 6.5V Q19 6.5V Q20 6.5V Ground (4) VREF (+13V) (3) +VS(+26V) (6) IL4145A SCHEMATIC DIAGRAM IL4145A N SUFFIX PLASTIC DIP (MS – 001BA) A Dimension, mm 5 8 B 1 4 MIN MAX A 8.51 10.16 B 6.1 7.11 5.33 C L F Symbol C D 0.36 0.56 F 1.14 1.78 -T- SEATING PLANE N G M K 0.25 (0.010) M J H D T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AA) Dimension, mm A 8 5 B H 1 G P 4 D K MIN MAX A 4.8 5 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 R x 45 C -T- Symbol SEATING PLANE J F 0.25 (0.010) M T C M M G 1.27 H 5.72 J 0° 8° K 0.1 0.25 1. Dimensions A and B do not include mold flash or protrusion. M 0.19 0.25 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. P 5.8 6.2 R 0.25 0.5 NOTES: