TECHNICAL DATA IW4098B Two Multivibrators (flip-flop) High-Voltage Silicon-Gate CMOS The IW4098B was especially designed for high-performance computing machinery with low power consumption, portable measuring equipment, communication systems with power supply from phone network, devices with power supply from solar battery, thermocouple etc. • Standard symmetric output features • Wide range of supply voltage 3.0 to 18 V. • 100%-control of DC characteristics at supply voltage 20V • Maximum input current of 1 μA at 18 V over full package-temperature range; 100 nA at 18 V and 25°C • Noise margin (over full package temperature range): 1.0 V min @ 5.0 V supply 2.0 V min @ 10.0 V supply 2.5 V min @ 15.0 V supply ORDERING INFORMATION IW4098BN Plastic IW4098BD SOIC TA = -55° to 125° C for all packages Pin description Pin number 01 02 Symbol Cx1 RxCx(1) 03 04 05 06 07 08 09 10 11 12 13 14 RES1 +TR1 -TR1 Q1 NQ1 GND NQ2 Q2 -TR2 +TR2 RES2 RxCx(2) 15 16 Description For capacitor connection For resistor & capacitor connection Reset Data input Data input Data output Data output Common Data output Data output Data input Data input Reset For resistor & capacitor connection For capacitor connection Supply input Cx2 VDD TRUTH TABLE (serial input) RES L H Input +TR X H L H , H H H H L PIN ASSIGNMENT 01 16 RxCx(1) 02 15 Cx1 V Cx2 Reset1 03 14 RxCx(2) +TR1 04 13 Reset2 -TR1 05 12 +TR2 Q1 06 11 -TR2 NQ1 07 10 Q2 VSS 08 09 NQ2 Output -TR X H Q L Q H 0 No switching , H No switching DD No switching No switching Rev. 00 IW4098B Logic diagram VDD D 0 4(12) C +TR R1 -TR R2 VDD 5(11) 3(13) Reset 2(14) RxCx VSS 1(15) 8 16 VSS Q Q VDD 6(10) 7(9) VDD = pin 16 VSS = pin 8 Rev. 00 IW4098B MAXIMUM RATINGS* Symbol VCC VIN VOUT IIN PD PD Tstg TL Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Output Voltage (Referenced to GND) DC Input Current, per Pin Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ Dissipation per Output Transistor Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) Value -0.5 to +20 -0.5 to VCC +0.5 -0.5 to VCC +0.5 ±10 750 500 100 -65 to +150 260 Unit V V V mA mW mW °C °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT TA Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) Operating Temperature, All Package Types Min 3.0 0 -55 Max 18 VCC +125 Unit V V °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. Rev. 00 IW4098B DC ELECTRICAL CHARACTERISTICS(Voltages Referenced to GND) Parameter, unit Sym- Test conditions bol UI UI UOL L H V 3.0 5.0 10 15 18 3.5 7.0 11 3.0 5.0 10 15 18 3.5 7.0 11 18 Low level output voltage,V UOL High level output voltage,V UOH Low level input current, μA IIL V 0 0 0 0 0 1.5 3.0 4.0 0 0 0 0 0 1.5 3.0 4.0 0 High level input current, μA IIH 0 18 Consumption current, μA IDD Low level output current, mA IOL High level output current, mA IOH Output leakage current , μA IOUT 0 0 0 0 0 0 0 0 0 0 0 0 5.0 10 15 20 5.0 10 15 5.0 5.0 10 15 18 UOH IOL IOH UDD V Guaranteed Limit TA=-55 oC TA=125 oC TA=25oC μA -1.0 -1.0 -1.0 -1.0 -1.0 -1.0 -1.0 -1.0 - V 3.0 5.0 10 15 18 5.0 10 15 3.0 5.0 10 15 18 5.0 10 15 18 max min max - μA 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 - min - 2.9 4.95 9.95 14.95 17.9 4.5 9.0 13.5 - 0.1 0.05 0.05 0.05 0.1 0.5 1.0 1.5 -0.1 2.9 4.95 9.95 14.95 17.9 4.5 9.0 13.5 - 0.1 0.05 0.05 0.05 0.1 0.5 1.0 1.5 -1.0 2.9 4.95 9.95 14.95 17.9 4.5 9.0 13.5 - 0.1 0.05 0.05 0.05 0.1 0.5 1.0 1.5 -0.1 - - - - 18 - 0.1 - 1.0 - 0.1 - - 5.0 10 15 20 5.0 10 15 5.0 5.0 10 15 18 0.64 1.6 4.2 -0.64 -2.0 -1.6 -4.2 1.0 2.0 4.0 20 ±0.4 0.36 0.9 2.4 -0.36 -1.15 -0.9 -2.4 30 60 120 600 ±12 0.51 1.3 3.4 -0.51 -1.6 -1.3 -3.4 1.0 2.0 4.0 20 ±0.4 V 0.4 0.5 1.5 4.6 2.5 9.5 13.5 UO=0.5 V max min Rev. 00 IW4098B AC ELECTRICAL CHARACTERISTICS(CL=50pF, RL=200kΩ, Input tr=tf=20 ns) Parameter, unit Symbo l Propagation delay at switch on & switch off, ns inputs +TR, -TR outputs Q, Q Test conditions RX CX pF kΩ tLH=tHL ≤ 20 ns, CL=50pF, RL= 200 kΩ tPHL1, tPLH1 5-10000 input RES outputs Q, Q ≥ 15 tPHL2, tPLH2 Pulse width of signals +TR, -TR, ns tWL, tWH Pulse width of signal RES, ns 15 tWR 100 1000 100000 TA=-55 oC UDD V min 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 max Guaranteed Limit TA=125 oC min 500 250 200 450 250 150 140 60 40 200 80 60 1200 600 500 50 30 20 max TA=25oC min 1000 500 400 900 500 300 280 120 80 400 160 120 2400 1200 1000 100 60 40 CAPACITY CHARACTERISTICS Symbol CIN Parameter Input capacity VDD, V Value Unit 7.5 pF Rev. 00 max 500 250 200 450 250 150 140 60 40 200 80 60 1200 600 500 50 30 20 IW4098B Time Diagram tLH tHL UDD 0.9 Input TR+ 0.5 0V 0.1 t W tPLH 0.9 Output Q 0.5UDD 0.1 tTLH tPHL UOL UOH 0.9 Output NQ 0.5UDD 0.1 tTHL tHL UOL tLH 0.9 Input TR- UOH 0.9 0.5 0.5 0.1 0.1 UDD 0V tW tPLH 0.9 Output Q UOH 0.5UDD 0.1 tTLH tPHL UOH 0.9 Output NQ tTHL UOL 0.5UDD 0.1 UOL Rev. 00 IW4098B N SUFFIX PLASTIC (MS - 001BB) A 9 16 Dimensions, mm B 1 8 F C -T- SEATING PLANE N K M J H D MIN MAX A 18.67 19.69 B 6.10 7.11 C L G Symbol 0.25 (0.010) M T NOTES: 1. imensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. 5.33 D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.20 0.36 N 0.38 D SUFFIX SOIC (MS - 012AC) A 16 9 H Dimensions, mm B 1 G P 8 R x 45 C -TK D SEATING PLANE J F 0.25 (0.010) M T C M NOTES: 1.Dimensions A and B do not include mold flash or protrusion. 2.Maximum mold flash or protrusion 0.15 mm (0.006) per side for A, for B - 0.25 mm (0.010) per side. M Symbol. MIN MAX A 9.80 10.0 B 3.80 4.00 C 1.35 1.75 D 0.33 0.51 F 0.40 1.27 G 1.27 H 5.72 J 0° 8° K 0.10 0.25 M 0.19 0.25 P 5.80 6.20 R 0.25 0.50 Rev. 00