Mobile Intel Pentium 4
Processor-M
Datasheet
June 2003
Order Number: 250686-007
Information in this document is provided solely to enable use of Intel products. Intel assumes no liability whatsoever, including
infringement of any patent or copyright, for sale and use of Intel products except as provided in Intel's Terms and Conditions of Sale
for such products. Information contained herein supersedes previously published specifications on these devices from Intel.
Actual system-level properties, such as skin temperature, are a function of various factors, including component placement,
component power characteristics, system power and thermal management techniques, software application usage and general
system design. Intel is not responsible for its customers' system designs, nor is Intel responsible for ensuring that its customers'
products comply with all applicable laws and regulations. Intel provides this and other thermal design information for informational
purposes only. System design is the sole responsibility of Intel's customers, and Intel's customers should not rely on any Intelprovided information as either an endorsement or recommendation of any particular system design characteristics.
Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise,
to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions of Sale for such
products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of
Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any
patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining
applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Intel
reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future
changes to them.
The Mobile Intel Pentium 4 Processor-M may contain design defects or errors known as errata which may cause the product to
deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be
obtained by calling 1-800-548-4725 or by visiting Intel’s Website at http://www.intel.com
Copyright © Intel Corporation 2000-2003.
Intel, Pentium, Intel NetBurst, and SpeedStep are registered trademarks or trademarks of Intel Corporation and its subsidiaries in
the United States and other countries.
* Other brands and names are the property of their respective owners.
2
Mobile Intel Pentium 4 Processor-M Datasheet
Contents
1.
Introduction......................................................................................................................... 9
1.1
1.2
2.
Electrical Specifications.................................................................................................... 13
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
3.
3.2
3.3
Processor Pin-Out ............................................................................................... 64
Pin Listing and Signal Definitions .....................................................................................67
5.1
5.2
6.
System Bus Clock (BCLK) Signal Quality Specifications and Measurement
Guidelines ...........................................................................................................51
System Bus Signal Quality Specifications and Measurement Guidelines........... 52
System Bus Signal Quality Specifications and Measurement Guidelines........... 55
3.3.1 Overshoot/Undershoot Guidelines ......................................................... 55
3.3.2 Overshoot/Undershoot Magnitude ......................................................... 55
3.3.3 Overshoot/Undershoot Pulse Duration................................................... 55
3.3.4 Activity Factor......................................................................................... 56
3.3.5 Reading Overshoot/Undershoot Specification Tables............................ 56
3.3.6 Conformance Determination to Overshoot/Undershoot Specifications .. 57
Package Mechanical Specifications .................................................................................61
4.1
5.
System Bus and GTLREF ................................................................................... 13
Power and Ground Pins ...................................................................................... 13
Decoupling Guidelines ........................................................................................ 13
2.3.1 VCC Decoupling ..................................................................................... 14
2.3.2 System Bus AGTL+ Decoupling............................................................. 14
2.3.3 System Bus Clock (BCLK[1:0]) and Processor Clocking .......................14
Voltage Identification and Power Sequencing..................................................... 15
2.4.1 Enhanced Intel® SpeedStep® Technology............................................ 16
2.4.2 Phase Lock Loop (PLL) Power and Filter............................................... 17
2.4.3 Catastrophic Thermal Protection............................................................ 18
Signal Terminations, Unused Pins and TESTHI[10:0] ........................................ 18
System Bus Signal Groups ................................................................................. 20
Asynchronous GTL+ Signals............................................................................... 22
Test Access Port (TAP) Connection.................................................................... 22
System Bus Frequency Select Signals (BSEL[1:0])............................................ 22
Maximum Ratings................................................................................................ 23
Processor DC Specifications............................................................................... 23
AGTL+ System Bus Specifications ..................................................................... 34
System Bus AC Specifications ............................................................................ 35
Processor AC Timing Waveforms ....................................................................... 40
System Bus Signal Quality Specifications........................................................................ 51
3.1
4.
Terminology......................................................................................................... 11
References .......................................................................................................... 11
Mobile Intel Pentium 4 Processor-M Pin Assignments........................................ 67
Alphabetical Signals Reference .......................................................................... 81
Thermal Specifications and Design Considerations......................................................... 89
6.1
Thermal Specifications ........................................................................................ 90
Mobile Intel Pentium 4 Processor-M Datasheet
3
Mobile Intel Pentium 4 Processor-M
6.1.1
6.1.2
7.
Configuration and Low Power Features........................................................................... 93
7.1
7.2
7.3
8.
Power-On Configuration Options ........................................................................ 93
Clock Control and Low Power States.................................................................. 93
7.2.1 Normal State .......................................................................................... 93
7.2.2 AutoHALT Powerdown State ................................................................. 93
7.2.3 Stop-Grant State .................................................................................... 94
7.2.4 HALT/Grant Snoop State ....................................................................... 95
7.2.5 Sleep State............................................................................................. 95
7.2.6 Deep Sleep State ................................................................................... 95
7.2.7 Deeper Sleep State ................................................................................ 96
Enhanced Intel SpeedStep Technology .............................................................. 96
Debug Tools Specifications.............................................................................................. 97
8.1
4
Thermal Diode........................................................................................ 90
Thermal Monitor ..................................................................................... 91
Logic Analyzer Interface (LAI) ............................................................................ 97
8.1.1 Mechanical Considerations .................................................................... 97
8.1.2 Electrical Considerations........................................................................ 97
Mobile Intel Pentium 4 Processor-M Datasheet
Figures
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
VCCVID Pin Voltage and Current Requirements ................................................ 15
Typical VCCIOPLL, VCCA and VSSA Power Distribution .................................. 17
Phase Lock Loop (PLL) Filter Requirements ..................................................... 18
Illustration of VCC Static and Transient Tolerances (VID = 1.30 V).................... 26
Illustration of VCC Static and Transient Tolerances (VID = 1.20 V).................... 28
Illustration of Deep Sleep VCC Static and Transient Tolerances (VID
Setting = 1.30 V) ................................................................................................. 29
ITPCLKOUT[1:0] Output Buffer Diagram ............................................................ 34
AC Test Circuit .................................................................................................... 41
TCK Clock Waveform.......................................................................................... 41
Differential Clock Waveform................................................................................ 42
Differential Clock Crosspoint Specification.......................................................... 43
System Bus Common Clock Valid Delay Timings............................................... 43
System Bus Reset and Configuration Timings....................................................44
Source Synchronous 2X (Address) Timings ....................................................... 44
Source Synchronous 4X Timings ........................................................................ 45
Power Up Sequence ........................................................................................... 46
Power Down Sequence....................................................................................... 46
Test Reset Timings ............................................................................................. 47
THERMTRIP# to Vcc Timing............................................................................... 47
FERR#/PBE# Valid Delay Timing ....................................................................... 47
TAP Valid Delay Timing ...................................................................................... 48
ITPCLKOUT Valid Delay Timing ......................................................................... 48
Stop Grant/Sleep/Deep Sleep Timing .................................................................49
Enhanced Intel SpeedStep Technology/Deep Sleep Timing .............................. 50
BCLK Signal Integrity Waveform......................................................................... 52
Low-to-High System Bus Receiver Ringback Tolerance..................................... 53
High-to-Low System Bus Receiver Ringback Tolerance..................................... 53
Low-to-High System Bus Receiver Ringback Tolerance for PWRGOOD and TAP
Buffers ................................................................................................................. 54
High-to-Low System Bus Receiver Ringback Tolerance for PWRGOOD and TAP
Buffers ................................................................................................................. 54
Maximum Acceptable Overshoot/Undershoot Waveform ................................... 59
Micro-FCPGA Package Top and Bottom Isometric Views .................................. 61
Micro-FCPGA Package Top and Side View........................................................ 62
Micro-FCPGA Package - Bottom View................................................................ 64
The Coordinates of the Processor Pins as Viewed From the Top of the
Package. ............................................................................................................. 65
Clock Control States............................................................................................ 94
Mobile Intel Pentium 4 Processor-M Datasheet
5
Mobile Intel Pentium 4 Processor-M
Tables
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
6
References.......................................................................................................... 11
Core Frequency to System Bus Multipliers ......................................................... 14
Voltage Identification Definition........................................................................... 16
System Bus Pin Groups ...................................................................................... 21
BSEL[1:0] Frequency Table for BCLK[1:0] ......................................................... 22
Processor DC Absolute Maximum Ratings ......................................................... 23
Voltage and Current Specifications..................................................................... 24
IMVP-III Voltage Regulator Tolerances for VID = 1.30 V Operating Mode
(Maximum Performance Mode)........................................................................... 25
IMVP-III Voltage Regulator Tolerances for VID = 1.20 V Operating Mode
(Battery Optimized Mode) ................................................................................... 27
IMVP-III Deep Sleep State Voltage Regulator Tolerances for Maximum
Performance Mode (VID = 1.30 V, VID Offset = 4.62%) ..................................... 28
IMVP-III Deep Sleep State Voltage Regulator Tolerances for Battery Optimized
Mode (VID = 1.20 V, VID Offset = 4.62%) .......................................................... 29
System Bus Differential BCLK Specifications ..................................................... 30
AGTL+ Signal Group DC Specifications ............................................................. 31
Asynchronous GTL+ Signal Group DC Specifications ........................................ 32
PWRGOOD and TAP Signal Group DC Specifications ...................................... 33
ITPCLKOUT[1:0] DC Specifications.................................................................... 33
BSEL [1:0] and VID[4:0] DC Specifications......................................................... 34
AGTL+ Bus Voltage Definitions........................................................................... 35
System Bus Differential Clock Specifications...................................................... 36
System Bus Common Clock AC Specifications .................................................. 36
System Bus Source Synch AC Specifications AGTL+ Signal Group .................. 37
Miscellaneous Signals AC Specifications ........................................................... 38
System Bus AC Specifications (Reset Conditions) ............................................. 38
TAP Signals AC Specifications ........................................................................... 39
ITPCLKOUT[1:0] AC Specifications .................................................................... 39
Stop Grant/Sleep/Deep Sleep/Enhanced Intel SpeedStep Technology AC
Specifications ...................................................................................................... 40
BCLK Signal Quality Specifications .................................................................... 51
Ringback Specifications for AGTL+ and Asynchronous GTL+ Signal Groups.... 52
Ringback Specifications for PWRGOOD Input and TAP Signal Groups............. 53
Source Synchronous (400 MHz) AGTL+ Signal Group Overshoot/Undershoot
Tolerance ............................................................................................................ 57
Source Synchronous (200 MHz) AGTL+ Signal Group Overshoot/Undershoot
Tolerance ............................................................................................................ 58
Common Clock (100 MHz) AGTL+ Signal Group Overshoot/Undershoot
Tolerance ............................................................................................................ 58
Asynchronous GTL+, PWRGOOD Input, and TAP Signal Groups
Overshoot/Undershoot Tolerance ....................................................................... 59
Micro-FCPGA Package Dimensions ................................................................... 63
Pin Listing by Pin Name ...................................................................................... 68
Pin Listing by Pin Number ................................................................................... 74
Signal Description ............................................................................................... 81
Power Specifications for the Mobile Intel Pentium 4 Processor-M...................... 89
Thermal Diode Interface...................................................................................... 90
Mobile Intel Pentium 4 Processor-M Datasheet
40
41
Thermal Diode Specifications.............................................................................. 90
Power-On Configuration Option Pins .................................................................. 93
Mobile Intel Pentium 4 Processor-M Datasheet
7
Mobile Intel Pentium 4 Processor-M
Revision History
Date
Description
March 2002
001
Initial release of the Datasheet
April 2002
002
Updates include:
June 2002
September 2002
January 2003
April 2003
June 2003
8
Revision
003
004
005
006
007
•
Added new processor speeds: 1.4 GHz, 1.5 GHz, & 1.8 GHz
•
Added PROCHOT# signal in Table 21
•
Updated signal description for PROCHOT# in Table 37 and Section 6.1.2
•
Updated the description of the Enhanced Intel Speedstep Technology in
sections 2.4.1 and 7.3
•
Updated PWRGOOD signal in Table 3, Section 2.7, Table 14, Table 21,
Table 28, Table 35, Figure 28, and FIgure 29
Updates include:
•
Added specifications for new processor speeds: 1.90 GHz and 2 GHz
•
Added die length and die width for processors based on B0-step shrink
process in Table 33
Updates include:
•
Added 2.2 GHz Mobile Intel Pentium 4 Processor-M specifications.
•
Current and power specifications updated in Table 7 & Table 38.
•
Corrected STPCLK#/SLP# timing relationship in Section 7.2.3 to match
parameter T75.
Updates include:
•
Added 2.4 GHz Mobile Intel Pentium 4 Processor-M specifications.
•
Current and power specifications updated in Table 7 & Table 38.
•
Clarified DBI[3:0]# and THERMTRIP# descriptions in Table 37.
•
Clarified thermal solution requirements in Section 6.
Updates include:
•
Added 2.5 GHz Mobile Intel Pentium 4 Processor-M specifications.
•
Current and power specifications updated in Table 7 & Table 38.
Updates include:
•
Added 2.6 GHz Mobile Intel Pentium 4 Processor-M specifications.
•
Updated note 5 in Table 22.
•
Updated THERMTRIP# description in Table 37.
Mobile Intel Pentium 4 Processor-M Datasheet
Introduction
1.
Introduction
The Mobile Intel Pentium 4 Processor-M is the first Intel mobile processor with the Intel
NetBurstTM micro-architecture. The Mobile Intel Pentium 4 Processor-M utilizes a 478-pin, Micro
Flip-Chip Pin Grid Array (Micro-FCPGA) package, and plugs into a surface-mount, Zero Insertion
Force (ZIF) socket. The Mobile Intel Pentium 4 Processor-M maintains full compatibility with IA32 software. In this document the Mobile Intel Pentium 4 Processor-M will be referred to as the
“Mobile Intel Pentium 4 Processor-M” or simply “the processor.”
The Intel NetBurst micro-architecture features include hyper-pipelined technology, a rapid
execution engine, a 400-MHz system bus, and an execution trace cache. The hyper pipelined
technology doubles the pipeline depth in the Mobile Intel Pentium 4 Processor-M allowing the
processor to reach much higher core frequencies. The rapid execution engine allows the two
integer ALUs in the processor to run at twice the core frequency, which allows many integer
instructions to execute in 1/2 clock tick. The 400-MHz system bus is a quad-pumped bus running
off a 100-MHz system clock making 3.2 GB/sec data transfer rates possible. The execution trace
cache is a first level cache that stores approximately 12-k decoded micro-operations, which
removes the instruction decoding logic from the main execution path, thereby increasing
performance.
Additional features within the Intel NetBurst micro-architecture include advanced dynamic
execution, advanced transfer cache, enhanced floating point and multi-media unit, and Streaming
SIMD Extensions 2 (SSE2). The advanced dynamic execution improves speculative execution and
branch prediction internal to the processor. The advanced transfer cache is a 512 kB, on-die level 2
(L2) cache. A new floating point and multi media unit has been implemented which provides
superior performance for multi-media and mathematically intensive applications. Finally, SSE2
adds 144 new instructions for double-precision floating point, SIMD integer, and memory
management. Power management capabilities such as AutoHALT, Stop-Grant, Sleep, Deep Sleep,
and Deeper Sleep have been incorporated. The processor includes an address bus powerdown
capability which removes power from the address and data pins when the system bus is not in use.
This feature is always enabled on the processor.
The Streaming SIMD Extensions 2 (SSE2) enable break-through levels of performance in
multimedia applications including 3-D graphics, video decoding/encoding, and speech recognition.
The new packed double-precision floating-point instructions enhance performance for applications
that require greater range and precision, including scientific and engineering applications and
advanced 3-D geometry techniques, such as ray tracing.
The Mobile Intel Pentium 4 Processor-M’s 400-MHz Intel NetBurst micro-architecture system bus
utilizes a split-transaction, deferred reply protocol like the Intel Pentium 4 Processor. This system
bus is not compatible with the P6 processor family bus. The 400-MHz Intel NetBurst microarchitecture system bus uses Source-Synchronous Transfer (SST) of address and data to improve
performance by transferring data four times per bus clock (4X data transfer rate, as in AGP 4X).
Along with the 4X data bus, the address bus can deliver addresses two times per bus clock and is
referred to as a “double-clocked” or 2X address bus. Working together, the 4X data bus and 2X
address bus provide a data bus bandwidth of up to 3.2 Gbytes/second.
The processor, when used in conjunction with the requisite Intel SpeedStep technology applet or
its equivalent, supports Enhanced Intel SpeedStep technology, which enables real-time dynamic
switching of the voltage and frequency between two performance modes. This occurs by switching
the bus ratios, core operating voltage, and core processor speeds without resetting the system.
Mobile Intel Pentium 4 Processor-M Datasheet
9
Introduction
The processor system bus uses a variant of GTL+ signalling technology called Assisted Gunning
Transceiver Logic (AGTL+) signal technology. The Mobile Intel Pentium 4 Processor-M is
available at the following core frequencies:
• 2.6 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 2.5 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 2.4 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 2.2 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 2.0 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 1.9 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 1.8 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 1.7 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 1.6 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 1.5 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
• 1.4 GHz (in Maximum Performance Mode at 1.30 V). This processor runs at 1.2 GHz (in
Battery Optimized Mode at 1.20 V)
10
Mobile Intel Pentium 4 Processor-M Datasheet
Introduction
1.1
Terminology
A “#” symbol after a signal name refers to an active low signal, indicating a signal is in the active
state when driven to a low level. For example, when RESET# is low, a reset has been requested.
Conversely, when NMI is high, a nonmaskable interrupt has occurred. In the case of signals where
the name does not imply an active state but describes part of a binary sequence (such as address or
data), the “#” symbol implies that the signal is inverted. For example, D[3:0] = “HLHL” refers to a
hex ‘A’, and D[3:0]# = “LHLH” also refers to a hex “A” (H= High logic level, L= Low logic level).
“System Bus” refers to the interface between the processor and system core logic (a.k.a. the chipset
components). The system bus is a multiprocessing interface to processors, memory, and I/O.
Commonly used terms are explained here for clarification:
• Processor — For this document, the term processor shall mean the Mobile Intel Pentium 4
Processor-M in the 478-pin package.
• Keep out zone — The area on or near the processor that system design can not utilize.
• Intel 845MP/845MZ chipsets — Mobile chipsets that will support the Mobile Intel
Pentium 4 Processor-M.
• Processor core — Mobile Intel Pentium 4 Processor-M core die with integrated L2 cache.
• Micro-FCPGA package — Micro Flip-Chip Pin Grid Array package with 50-mil pin pitch.
1.2
References
Material and concepts available in the following documents may be beneficial when reading this
document.
Table 1.
References
Document
Mobile Intel Pentium
Platform Design Guide
4 Processor-M and Intel 845MP/845MZ Chipset
Order Number
250688-002
Intel Architecture Software Developer's Manual
Volume I: Basic Architecture
245470
Volume II: Instruction Set Reference
245471
Volume III: System Programming Guide
245472
Mobile Intel Pentium 4 Processor-M Datasheet
11
Introduction
This page intentionally left blank.
12
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
2.
Electrical Specifications
2.1
System Bus and GTLREF
Most Mobile Intel Pentium 4 Processor-M system bus signals use Assisted Gunning Transceiver
Logic (AGTL+) signalling technology. As with the Intel P6 family of microprocessors, this
signalling technology provides improved noise margins and reduced ringing through low-voltage
swings and controlled edge rates. The termination voltage level for the Mobile Intel Pentium 4
Processor-M AGTL+ signals is VCC, which is the operating voltage of the processor core. Previous
generations of Intel mobile processors utilize a fixed termination voltage known as VCCT. The use
of a termination voltage that is determined by the processor core allows better voltage scaling on
the system bus for Mobile Intel Pentium 4 Processor-M. Because of the speed improvements to
data and address bus, signal integrity and platform design methods have become more critical than
with previous processor families. Design guidelines for the Mobile Intel Pentium 4 Processor-M
system bus will be detailed in the Mobile Intel Pentium 4 Processor-M and Intel 845MP/
845MZ Chipset Platform Design Guide.
The AGTL+ inputs require a reference voltage (GTLREF) which is used by the receivers to
determine if a signal is a logical 0 or a logical 1. GTLREF must be generated on the system board.
Termination resistors are provided on the processor silicon and are terminated to its core voltage
(VCC). Intel’s 845MP/845MZ chipsets will also provide on-die termination, thus eliminating the
need to terminate the bus on the system board for most AGTL+ signals. However, some AGTL+
signals do not include on-die termination and must be terminated on the system board. For more
information, refer to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ
Chipset Platform Design Guide.
The AGTL+ bus depends on incident wave switching. Therefore, timing calculations for AGTL+
signals are based on flight time as opposed to capacitive deratings. Analog signal simulation of the
system bus, including trace lengths, is highly recommended when designing a system.
2.2
Power and Ground Pins
For clean on-chip power distribution, the Mobile Intel Pentium 4 Processor-M have 85 VCC
(power) and 181 VSS (ground) inputs. All power pins must be connected to VCC, while all VSS pins
must be connected to a system ground plane.The processor VCC pins must be supplied with the
voltage determined by the VID (Voltage ID) pins and the loadline specifications (see Figure 4 to
Figure 6).
2.3
Decoupling Guidelines
Due to its large number of transistors and high internal clock speeds, the processor is capable of
generating large average current swings between low and full power states. This may cause
voltages on power planes to sag below their minimum values if bulk decoupling is not adequate.
Care must be taken in the board design to ensure that the voltage provided to the processor remains
within the specifications listed in Table 7. Failure to do so can result in timing violations and/or
Mobile Intel Pentium 4 Processor-M Datasheet
13
Electrical Specifications
affect the long term reliability of the processor. For further information and design guidelines, refer
to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design
Guide.
2.3.1
VCC Decoupling
Regulator solutions need to provide bulk capacitance with a low Effective Series Resistance (ESR)
and keep a low interconnect resistance from the regulator to the socket. Bulk decoupling for the
large current swings when the part is powering on, or entering/exiting low-power states, must be
provided by the voltage regulator solution. For more details on decoupling recommendations,
please refer to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset
Platform Design Guide.
2.3.2
System Bus AGTL+ Decoupling
The Mobile Intel Pentium 4 Processor-M integrates signal termination on the die and incorporates
high frequency decoupling capacitance on the processor package. Decoupling must also be
provided by the system motherboard for proper AGTL+ bus operation. For more information, refer
to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design
Guide.
2.3.3
System Bus Clock (BCLK[1:0]) and Processor Clocking
BCLK[1:0] directly controls the system bus interface speed as well as the core frequency of the
processor. As in previous generation processors, the Mobile Intel Pentium 4 Processor-M core
frequency is a multiple of the BCLK[1:0] frequency. Refer to Table 2 for the Mobile Intel Pentium
4 Processor-M supported ratios.
Table 2.
Core Frequency to System Bus Multipliers
Core Frequency
Multiplication of System Core Frequency
to System Bus Frequency
Notes2
800 MHz
1/8
1
1.2 GHz
1/12
1.4 GHz
1/14
1.5 GHz
1/15
1.6 GHz
1/16
1.7 GHz
1/17
1.8 GHz
1/18
1.9 GHz
1/19
2.0 GHz
1/20
2.2 GHz
1/22
2.4 GHz
1/24
2.5 GHz
1/25
2.6 GHz
1/26
NOTES:
1. Ratio is used for debug purposes only.
14
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
2. Listed frequencies are not necessarily committed production frequencies.
The Mobile Intel Pentium 4 Processor-M uses a differential clocking implementation. For more
information on Mobile Intel Pentium 4 Processor-M clocking.
2.4
Voltage Identification and Power Sequencing
The voltage set by the VID pins is the nominal/typical voltage setting for the processor. A
minimum voltage is provided in Table 7 and changes with frequency. This allows processors
running at a higher frequency to have a relaxed minimum voltage specification. The specifications
have been set such that one voltage regulator can work with all supported frequencies.
The Mobile Intel Pentium 4 Processor-M uses five voltage identification pins, VID[4:0], to support
automatic selection of power supply voltages. The VID pins for the Mobile Intel Pentium 4
Processor-M are open drain outputs driven by the processor VID circuitry. Table 3 specifies the
voltage level corresponding to the state of VID[4:0]. A “1” in this table refers to a high-voltage
level and a “0” refers to low-voltage level.
Power source characteristics must be stable whenever the supply to the voltage regulator is stable.
Refer to the Figure 16 for timing details of the power up sequence. Also refer to Mobile Intel
Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design Guide for
implementation details.
Mobile Intel Pentium 4 Processor-M’s Voltage Identification circuit requires an independent 1.2-V
supply. This voltage must be routed to the processor VCCVID pin. Figure 1 shows the voltage and
current requirements of the VCCVID pin.
Figure 1. VCCVID Pin Voltage and Current Requirements
1.2V+10%
1.2V-5%
1V
150mA to 300mA
80mA
30mA
1mA
70nS
5nS
Mobile Intel Pentium 4 Processor-M Datasheet
15
Electrical Specifications
Table 3.
Voltage Identification Definition
Processor Pins
2.4.1
VID4
VID3
VID2
VID1
VID0
VCC_
1
1
1
1
1
0.600
1
1
1
1
0
0.625
1
1
1
0
1
0.650
1
1
1
0
0
0.675
1
1
0
1
1
0.700
1
1
0
1
0
0.725
1
1
0
0
1
0.750
1
1
0
0
0
0.775
1
0
1
1
1
0.800
1
0
1
1
0
0.825
1
0
1
0
1
0.850
1
0
1
0
0
0.875
1
0
0
1
1
0.900
1
0
0
1
0
0.925
1
0
0
0
1
0.950
1
0
0
0
0
0.975
0
1
1
1
1
1.000
0
1
1
1
0
1.050
0
1
1
0
1
1.100
0
1
1
0
0
1.150
0
1
0
1
1
1.200
0
1
0
1
0
1.250
0
1
0
0
1
1.300
0
1
0
0
0
1.350
0
0
1
1
1
1.400
0
0
1
1
0
1.450
0
0
1
0
1
1.500
0
0
1
0
0
1.550
0
0
0
1
1
1.600
0
0
0
1
0
1.650
0
0
0
0
1
1.700
0
0
0
0
0
1.750
Enhanced Intel® SpeedStep® Technology
The Mobile Intel Pentium 4 Processor-M, when used in conjunction with the requisite Intel
SpeedStep technology applet or its equivalent, supports Enhanced Intel SpeedStep technology.
Enhanced Intel SpeedStep technology allows the processor to switch between two core frequencies
automatically based on CPU demand, without having to reset the processor or change the system
bus frequency. The processor operates in two modes, the Maximum Performance mode or the
Battery Optimized mode. Each frequency and voltage pair identifies the operating mode. The
processor drives the VID[4:0] pins with the correct VID for the current operating mode. After
reset, the processor will start in Battery Optimized mode. Any RESET# assertion will force the
16
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
processor to the Battery Optimized mode. INIT# assertions ("soft" resets) and APIC bus INIT
messages do not change the operating mode of the processor. Some electrical and thermal
specifications are for a specific voltage and frequency. The Mobile Intel Pentium 4 Processor-M
featuring Enhanced Intel SpeedStep technology will meet the electrical and thermal specifications
specific to the current operating mode, and it is not guaranteed to meet the electrical and thermal
specifications specific to the opposite operating mode. The timing specifications must be met when
performing an operating mode transition.
2.4.2
Phase Lock Loop (PLL) Power and Filter
VCCA and VCCIOPLL are power sources required by the PLL clock generators on the Mobile Intel
Pentium 4 Processor-M silicon. Since these PLLs are analog in nature, they require quiet power
supplies for minimum jitter. Jitter is detrimental to the system: it degrades external I/O timings as
well as internal core timings (i.e. maximum frequency). To prevent this degradation, these supplies
must be low pass filtered from VCCVID. A typical filter topology is shown in Figure 2.
The AC low-pass requirements, with input at VCCVID and output measured across the capacitor
(CA or CIO in Figure 2), is as follows:
•
•
•
•
< 0.2 dB gain in pass band
< 0.5 dB attenuation in pass band < 1 Hz
> 34 dB attenuation from 1 MHz to 66 MHz
> 28 dB attenuation from 66 MHz to core frequency
The filter requirements are illustrated in Figure 3. For recommendations on implementing the filter
refer to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform
Design Guide.
Figure 2. Typical VCCIOPLL, VCCA and VSSA Power Distribution
V CCVID
L
VCCA
CA
PLL
VSSA
Processor
Core
C IO
VCCIOPLL
L
Mobile Intel Pentium 4 Processor-M Datasheet
17
Electrical Specifications
.
Figure 3. Phase Lock Loop (PLL) Filter Requirements
0.2 dB
0 dB
-0.5 dB
forbidden
zone
-28 dB
forbidden
zone
-34 dB
DC
1 Hz
fpeak
1 MHz
66 MHz
fcore
high frequency
band
passband
NOTES:
1. Diagram not to scale.
2. No specification for frequencies beyond fcore (core frequency).
3. fpeak, if existent, should be less than 0.05 MHz.
2.4.3
Catastrophic Thermal Protection
The Mobile Intel Pentium 4 Processor-M supports the THERMTRIP# signal for catastrophic
thermal protection. Alternatively an external thermal sensor can be used to protect the processor
and the system against excessive temperatures. Even with the activation of THERMTRIP#, which
halts all processor internal clocks and activity, leakage current can be high enough such that the
processor cannot be protected in all conditions without the removal of power to the processor. If the
external thermal sensor detects a catastrophic processor temperature of 135°C (maximum), or if the
THERMTRIP# signal is asserted, the VCC supply to the processor must be turned off within
500 ms to prevent permanent silicon damage due to thermal runaway of the processor. Refer to
Section 5.2 for more details on THERMTRIP#.
2.5
Signal Terminations, Unused Pins and TESTHI[10:0]
All NC pins must remain unconnected. Connection of these pins to VCC, VSS, or to any other signal
(including each other) can result in component malfunction or incompatibility with future Mobile
Intel Pentium 4 Processor-M. See Section 5.2 for a pin listing of the processor and the location of
all NC pins.
18
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
For reliable operation, always connect unused inputs or bidirectional signals that are not terminated
on the die to an appropriate signal level. Note that on-die termination has been included on the
Mobile Intel Pentium 4 Processor-M to allow signals to be terminated within the processor silicon.
Unused active low AGTL+ inputs may be left as no connects if AGTL+ termination is provided on
the processor silicon. Table 4 lists details on AGTL+ signals that do not include on-die termination.
Unused active high inputs should be connected through a resistor to ground (VSS). Refer to the
Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design Guide
for the appropriate resistor values.
Unused outputs can be left unconnected, however, this may interfere with some TAP functions,
complicate debug probing, and prevent boundary scan testing. A resistor must be used when tying
bidirectional signals to power or ground. When tying any signal to power or ground, a resistor will
also allow for system testability. For unused AGTL+ input or I/O signals that don’t have on-die
termination, use pull-up resistors of the same value in place of the on-die termination resistors
(RTT). See Table 18.
The TAP, Asynchronous GTL+ inputs, and Asynchronous GTL+ outputs do not include on-die
termination. Inputs and used outputs must be terminated on the system board. Unused outputs may
be terminated on the system board or left unconnected. Note that leaving unused outputs
unterminated may interfere with some TAP functions, complicate debug probing, and prevent
boundary scan testing. Signal termination for these signal types is discussed in the Mobile Intel
Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design Guide.
The TESTHI pins should be tied to the processor VCC using a matched resistor, where a matched
resistor has a resistance value within + 20% of the impedance of the board transmission line traces.
For example, if the trace impedance is 50 Ω, then a value between 40 Ω and 60 Ω is required.
The TESTHI pins may use individual pull-up resistors or be grouped together as detailed below. A
matched resistor should be used for each group:
1. TESTHI[1:0]
2. TESTHI[5:2]
3. TESTHI[10:8]
Additionally, if the ITPCLKOUT[1:0] pins are not used then they may be connected individually to
VCC using matched resistors or grouped with TESTHI[5:2] with a single matched resistor. If they
are being used, individual termination with 1-kΩ resistors is required. Tying ITPCLKOUT[1:0]
directly to VCC or sharing a pull-up resistor to VCC will prevent use of debug interposers. This
implementation is strongly discouraged for system boards that do not implement an onboard debug
port.
As an alternative, group 2 (TESTHI[5:2]), and the ITPCLKOUT[1:0] pins may be tied directly to
the processor VCC. This has no impact on system functionality. TESTHI[0] may also be tied
directly to processor VCC if resistor termination is a problem, but matched resistor termination is
recommended. In the case of the ITPCLKOUT[1:0] pins, direct tie to VCC is strongly discouraged
for system boards that do not implement an onboard debug port.
Tying any of the TESTHI pins together will prevent the ability to perform boundary scan testing.
Pullup/down resistor requirements for the VID[4:0] and BSEL[1:0] signals are included in the
signal descriptions in Section 5.
Mobile Intel Pentium 4 Processor-M Datasheet
19
Electrical Specifications
2.6
System Bus Signal Groups
In order to simplify the following discussion, the system bus signals have been combined into
groups by buffer type. AGTL+ input signals have differential input buffers, which use GTLREF as
a reference level. In this document, the term "AGTL+ Input" refers to the AGTL+ input group as
well as the AGTL+ I/O group when receiving. Similarly, "AGTL+ Output" refers to the AGTL+
output group as well as the AGTL+ I/O group when driving.
With the implementation of a source synchronous data bus comes the need to specify two sets of
timing parameters. One set is for common clock signals which are dependant upon the rising edge
of BCLK0 (ADS#, HIT#, HITM#, etc.) and the second set is for the source synchronous signals
which are relative to their respective strobe lines (data and address) as well as the rising edge of
BCLK0. Asychronous signals are still present (A20M#, IGNNE#, etc.) and can become active at
any time during the clock cycle. Table 4 identifies which signals are common clock, source
synchronous, and asynchronous.
20
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Table 4.
System Bus Pin Groups
Signal Group
Signals1
Type
AGTL+ Common Clock Input
Common
clock
BPRI#, DEFER#, RESET#2, RS[2:0]#, RSP#, TRDY#
AGTL+ Common Clock I/O
Synchronous
AP[1:0]#, ADS#, BINIT#, BNR#, BPM[5:0]#2, BR0#2,
DBSY#, DP[3:0]#, DRDY#, HIT#, HITM#, LOCK#,
MCERR#
Signals
Associated Strobe
5
AGTL+ Source Synchronous
I/O
Source
Synchronous
REQ[4:0]#, A[16:3]#
ADSTB0#
5
A[35:17]#
ADSTB1#
D[15:0]#, DBI0#
DSTBP0#, DSTBN0#
D[31:16]#, DBI1#
DSTBP1#, DSTBN1#
D[47:32]#, DBI2#
DSTBP2#, DSTBN2#
D[63:48]#, DBI3#
DSTBP3#, DSTBN3#
AGTL+ Strobes
Common
Clock
ADSTB[1:0]#, DSTBP[3:0]#, DSTBN[3:0]#
Asynchronous GTL+ Input4,5
Asynchronous
A20M#, DPSLP#, GHI#, IGNNE#, INIT#5, LINT0/INTR,
LINT1/NMI, SMI#5, SLP#, STPCLK#
Asynchronous GTL+ Output4
Asynchronous
FERR#/PBE#, IERR#2, THERMTRIP#, PROCHOT#
TAP Input4
Synchronous
to TCK
TCK, TDI, TMS, TRST#
TAP Output4
Synchronous
to TCK
TDO
System Bus Clock
N/A
BCLK[1:0], ITP_CLK[1:0]3
N/A
VCC, VCCA, VCCIOPLL, VCCVID, VID[4:0], VSS, VSSA,
GTLREF[3:0], COMP[1:0], NC, TESTHI[5:0],
TESTHI[10:8], ITPCLKOUT[1:0], PWRGOOD,
THERMDA, THERMDC, SKTOCC#, VCC_SENSE,
VSS_SENSE, BSEL[1:0], DBR#3
Power/Other
NOTES:
1. Refer to Section 5.2 for signal descriptions.
2. These AGTL+ signals do not have on-die termination. Refer to Section 2.5 for termination requirements.
3. In processor systems where there is no debug port implemented on the system board, these signals are used
to support a debug port interposer. In systems with the debug port implemented on the system board, these
signals are no connects.
4. These signal groups are not terminated by the processor. Signals not driven by the ICH3-M component must
be terminated on the system board. Refer to Section 2.5 and the Mobile Intel Pentium 4 Processor-M and
Intel 845MP/845MZ Chipset Platform Design Guide for termination requirements and further details.
5. The value of these pins during the active-to-inactive edge of RESET# defines the processor configuration
options. See Section 7.1 for details.
Mobile Intel Pentium 4 Processor-M Datasheet
21
Electrical Specifications
2.7
Asynchronous GTL+ Signals
Mobile Intel Pentium 4 Processor-M does not utilize CMOS voltage levels on any signals that
connect to the processor. As a result, legacy input signals such as A20M#, IGNNE#, INIT#,
LINT0/INTR, LINT1/NMI, SMI#, SLP#, and STPCLK# use GTL+ input buffers. Legacy output
FERR#/PBE# and other non-AGTL+ signals (THERMTRIP# and PROCHOT#) use GTL+ output
buffers. All of these signals follow the same DC requirements as AGTL+ signals, however the
outputs are not actively driven high (during a logical 0 to 1 transition) by the processor (the major
difference between GTL+ and AGTL+). These signals do not have setup or hold time specifications
in relation to BCLK[1:0]. However, all of the Asynchronous GTL+ signals are required to be
asserted for at least two BCLKs in order for the processor to recognize them. See Section 2.11 and
Section 2.13 for the DC and AC specifications for the Asynchronous GTL+ signal groups.
2.8
Test Access Port (TAP) Connection
Due to the voltage levels supported by other components in the Test Access Port (TAP) logic, it is
recommended that the Mobile Intel Pentium 4 Processor-M be first in the TAP chain and followed
by any other components within the system. A translation buffer should be used to connect to the
rest of the chain unless one of the other components is capable of accepting an input of the
appropriate voltage level. Similar considerations must be made for TCK, TMS, and TRST#. Two
copies of each signal may be required, with each driving a different voltage level.
2.9
System Bus Frequency Select Signals (BSEL[1:0])
The BSEL[1:0] are output signals used to select the frequency of the processor input clock
(BCLK[1:0]). Table 5 defines the possible combinations of the signals and the frequency
associated with each combination. The required frequency is determined by the processor, chipset,
and clock synthesizer. All agents must operate at the same frequency.
The Mobile Intel Pentium 4 Processor-M currently operates at a 400-MHz system bus frequency
(selected by a 100-MHz BCLK[1:0] frequency). Individual processors will only operate at their
specified system bus frequency.
For more information about these pins refer to Section 5.2 and the appropriate platform design
guidelines.
Table 5.
22
BSEL[1:0] Frequency Table for BCLK[1:0]
BSEL1
BSEL0
Function
L
L
100 MHz
L
H
RESERVED
H
L
RESERVED
H
H
RESERVED
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
2.10
Maximum Ratings
Table 6 lists the processor’s maximum environmental stress ratings. The processor should not
receive a clock while subjected to these conditions. Functional operating parameters are listed in
the AC and DC tables. Extended exposure to the maximum ratings may affect device reliability.
Furthermore, although the processor contains protective circuitry to resist damage from Electro
Static Discharge (ESD), one should always take precautions to avoid high static voltages or electric
fields.
Table 6.
Processor DC Absolute Maximum Ratings
Symbol
Parameter
Min
Max
Unit
Notes
TSTORAGE
Processor storage
temperature
–40
85
°C
2
VCC
Any processor supply
voltage with respect to VSS
-0.3
1.75
V
1
VinAGTL+
AGTL+ buffer DC input
voltage with respect to VSS
-0.1
1.75
V
VinAsynch_GTL+
Asynch GTL+ buffer DC
input voltage with respect
to VSS
-0.1
1.75
V
IVID
Max VID pin current
5
mA
NOTES:
1. This rating applies to any processor pin.
2. Contact Intel for storage requirements in excess of one year.
2.11
Processor DC Specifications
The processor DC specifications in this section are defined at the processor core (pads) unless
noted otherwise. See Section 5 for the pin signal definitions and signal pin assignments. Most of
the signals on the processor system bus are in the AGTL+ signal group. The DC specifications for
these signals are listed in Table 13.
Previously, legacy signals and Test Access Port (TAP) signals to the processor used low-voltage
CMOS buffer types. However, these interfaces now follow DC specifications similar to GTL+. The
DC specifications for these signal groups are listed in Table 14 and Table 15.
Table 7 through Table 17 list the DC specifications for the Mobile Intel Pentium 4 Processor-M and
are valid only while meeting specifications for junction temperature, clock frequency, and input
voltages. Unless specified otherwise, all specifications for the Mobile Intel Pentium 4 Processor-M
are at TJ = 100°C. Care should be taken to read all notes associated with each parameter.
Mobile Intel Pentium 4 Processor-M Datasheet
23
Electrical Specifications
Table 7.
Voltage and Current Specifications
Symbol
Parameter
Min
Typ
Max
Unit
Notes1
V
2, 3, 4,
5, 7, 8,11
VCC
VCC for core logic
Maximum Performance Mode
Battery Optimized Mode
VCCVID
VID supply voltage
-5%
1.2
+10%
V
2, 12
VCCDPRSLP
Transient Deeper Sleep voltage
0.91
1.00
1.09
V
2
VCCDPRSLP,DC
Static Deeper Sleep voltage
0.95
1.00
1.05
V
2
A
4, 5, 8, 9
1.3
1.2
Current for VCC at core frequency
2.60 GHz & 1.3 V
2.50 GHz & 1.3 V
2.40 GHz & 1.3 V
2.20 GHz & 1.3 V
2.00 GHz & 1.3 V
1.90 GHz & 1.3 V
1.80 GHz & 1.3 V
1.70 GHz & 1.3 V
1.60 GHz & 1.3 V
1.50 GHz & 1.3 V
1.40 GHz & 1.3 V
1.20 GHz & 1.2 V
38.8
37.7
36.7
34.5
33.3
32.2
31.0
29.9
28.7
27.5
26.3
22.1
IVCCVID
Current for VID supply
300
ISGNT, ISLP
ICC Stop-Grant and ICCSleep at
1.3 V (for > 2.0 GHz)
1.3 V (for <= 2.0 GHz)
1.2 V
10.5
10.1
8.9
ICC
mA
A
6, 9
9.0
8.3
A
9
A
ICC Deep Sleep at
IDSLP
1.3 V
1.2 V
IDPRSLP
ICC Deeper Sleep at 1.0V
6.9
ITCC
ICC TCC active
ICC
A
8
ICC PLL
ICC for PLL pins
60
mA
10
NOTES:
1. Unless otherwise noted, all specifications in this table are based on latest post-silicon measurements
available at the time of publication.
2. These voltages are targets only. A variable voltage source should exist on systems in the event that a
different voltage is required. See Section 2.4 and Table 3 for more information. The VID bits will set the typical
VCC with the minimum being defined according to current consumption at that voltage.
3. The voltage specification requirements are measured at the system board socket ball with a 100 MHz
bandwidth oscilloscope, 1.5 pF maximum probe capacitance, and 1 MΩ minimum impedance. The maximum
length of ground wire on the probe should be less than 5 mm. Ensure external noise from the system is not
coupled in the scope probe.
4. Refer to Table 8 to Table 11 and Figure 4 to Figure 6 for the minimum, typical, and maximum VCC (measured
at the system board socket ball) allowed for a given current. The processor should not be subjected to any
VCC and ICC combination wherein VCC exceeds VCC_MAX for a given current. Failure to adhere to this
specification can affect the long term reliability of the processor.
5. VCC_MIN is defined at ICC_MAX.
6. The current specified is also for AutoHALT State.
7. Typical VCC indicates the VID encoded voltage. Voltage supplied must conform to the load line specification
shown in Table 8 to Table 11.
8. The maximum instantaneous current the processor will draw while the thermal control circuit is active as
indicated by the assertion of PROCHOT# is the same as the maximum ICC for the processor.
9. Maximum specifications for ICC Core, ICC Stop-Grant, ICC Sleep, and ICC Deep Sleep are specified at VCC
Static Max. derived from the tolerances in Table 8 through Table 11, TJ Max., and under maximum signal
loading conditions.
24
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
10.The specification is defined per PLL pin.
11.The voltage response to a processor current load step (transient) must stay within the Transient Voltage
Tolerance Window. The voltage surge or droop response measured in this window is typically on the order of
several hundred nanoseconds to several microseconds. The Transient Voltage Tolerance Window is defined
as follows:
Case a) Load Current Step Up: e.g., from Icc = I_leakage to Icc = Icc_max. Allowable Vcc_min is defined as
minimum transient voltage at Icc = Icc_max for a period of time lasting several hundred nanoseconds to
several microseconds after the transient event.
Case b) Load Current Step Down: e.g., form Icc = Icc_max to Icc = I_leakage. Allowable Vcc_max is defined
as the maximum transient voltage at Icc = I_leakage for a period of time lasting several hundred
nanoseconds to several microseconds after the transient event.
12.This specification applies to both static and transient components. The rising edge of VCCVID must be
monotonic from 0 to 1.1 V. See Figure 1 for current requirements. In this case, monotonic is defined as
continuously increasing with less than 50 mV of peak to peak noise for any width greater than 2 nS
superimposed on the rising edge.
Table 8.
IMVP-III Voltage Regulator Tolerances for VID = 1.30 V Operating Mode (Maximum
Performance Mode)
VCC Nominal
(V)
VCC Static Min
(V)
VCC Static Max
(V)
VCC Transient
Min (V)
VCC Transient
Max (V)
0.0
1.300
1.275
1.325
1.255
1.345
1.0
1.298
1.273
1.323
1.253
1.343
2.0
1.296
1.271
1.321
1.251
1.341
3.0
1.294
1.269
1.319
1.249
1.339
4.0
1.292
1.267
1.317
1.247
1.337
5.0
1.290
1.265
1.315
1.245
1.335
6.0
1.288
1.263
1.313
1.243
1.333
7.0
1.286
1.261
1.311
1.241
1.331
8.0
1.284
1.259
1.309
1.239
1.329
9.0
1.282
1.257
1.307
1.237
1.327
10.0
1.280
1.255
1.305
1.235
1.325
11.0
1.278
1.253
1.303
1.233
1.323
12.0
1.276
1.251
1.301
1.231
1.321
13.0
1.274
1.249
1.299
1.229
1.319
14.0
1.272
1.247
1.297
1.227
1.317
15.0
1.270
1.245
1.295
1.225
1.315
16.0
1.268
1.243
1.293
1.223
1.313
17.0
1.266
1.241
1.291
1.221
1.311
18.0
1.264
1.239
1.289
1.219
1.309
19.0
1.262
1.237
1.287
1.217
1.307
20.0
1.260
1.235
1.285
1.215
1.305
21.0
1.258
1.233
1.283
1.213
1.303
22.0
1.256
1.231
1.281
1.211
1.301
23.0
1.254
1.229
1.279
1.209
1.299
24.0
1.252
1.227
1.277
1.207
1.297
ICC (A)
Mobile Intel Pentium 4 Processor-M Datasheet
25
Electrical Specifications
Table 8.
IMVP-III Voltage Regulator Tolerances for VID = 1.30 V Operating Mode (Maximum
Performance Mode)
ICC (A)
VCC Nominal
(V)
VCC Static Min
(V)
VCC Static Max
(V)
VCC Transient
Min (V)
VCC Transient
Max (V)
25.0
1.250
1.225
1.275
1.205
1.295
26.0
1.248
1.223
1.273
1.203
1.293
27.0
1.246
1.221
1.271
1.201
1.291
28.0
1.244
1.219
1.269
1.199
1.289
29.0
1.242
1.217
1.267
1.197
1.287
30.0
1.240
1.215
1.265
1.195
1.285
31.0
1.238
1.213
1.263
1.193
1.283
32.0
1.236
1.211
1.261
1.191
1.281
33.0
1.234
1.209
1.259
1.189
1.279
34.0
1.232
1.207
1.257
1.187
1.277
35.0
1.230
1.205
1.255
1.185
1.275
36.0
1.228
1.203
1.253
1.183
1.273
37.0
1.226
1.201
1.251
1.181
1.271
38.0
1.224
1.199
1.249
1.179
1.269
39.0
1.222
1.197
1.247
1.177
1.267
40.0
1.220
1.195
1.245
1.175
1.265
Figure 4. Illustration of VCC Static and Transient Tolerances (VID = 1.30 V)
Mobile Northwood Load Line for VID = 1.30V
1.400
Vcc Transient Maximum
1.350
Vcc Static Maximum
Vcc Nominal
1.300
VCC
1.250
1.200
Vcc Static Minimum
1.150
Vcc Transient
1.100
.0
.0
.0
40
38
36
.0
.0
.0
.0
.0
34
32
30
28
.0
24
26
.0
.0
.0
22
20
18
.0
.0
.0
.0
16
14
12
8.
0
10
6.
0
4.
0
2.
0
0.
0
1.050
Icc Maximum
26
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Table 9.
IMVP-III Voltage Regulator Tolerances for VID = 1.20 V Operating Mode (Battery
Optimized Mode)
ICC (A)
VCC Nominal
(V)
VCC Static Min
(V)
VCC Static Max
(V)
VCC Transient
Min (V)
VCC Transient
Max (V)
0.0
1.176
1.151
1.201
1.131
1.221
1.0
1.174
1.149
1.199
1.129
1.219
2.0
1.172
1.147
1.197
1.127
1.217
3.0
1.170
1.145
1.195
1.125
1.215
4.0
1.168
1.143
1.193
1.123
1.213
5.0
1.166
1.141
1.191
1.121
1.211
6.0
1.164
1.139
1.189
1.119
1.209
7.0
1.162
1.137
1.187
1.117
1.207
8.0
1.160
1.135
1.185
1.115
1.205
9.0
1.158
1.133
1.183
1.113
1.203
10.0
1.156
1.131
1.181
1.111
1.201
11.0
1.154
1.129
1.179
1.109
1.199
12.0
1.152
1.127
1.177
1.107
1.197
13.0
1.150
1.125
1.175
1.105
1.195
14.0
1.148
1.123
1.173
1.103
1.193
15.0
1.146
1.121
1.171
1.101
1.191
16.0
1.144
1.119
1.169
1.099
1.189
17.0
1.142
1.117
1.167
1.097
1.187
18.0
1.140
1.115
1.165
1.095
1.185
19.0
1.138
1.113
1.163
1.093
1.183
20.0
1.136
1.111
1.161
1.091
1.181
21.0
1.134
1.109
1.159
1.089
1.179
22.0
1.132
1.107
1.157
1.087
1.177
23.0
1.130
1.105
1.155
1.085
1.175
24.0
1.128
1.103
1.153
1.083
1.173
25.0
1.126
1.101
1.151
1.081
1.171
Mobile Intel Pentium 4 Processor-M Datasheet
27
Electrical Specifications
Figure 5. Illustration of VCC Static and Transient Tolerances (VID = 1.20 V)
Mobile Northwood Load Line for VID = 1.20V
1.250
Vcc Transient Maximum
Vcc Static Maximum
1.200
Vcc Nominal
VCC
1.150
1.100
Vcc Static Minimum
Vcc Transient Minimum
1.050
0.
0
1.
0
2.
0
3.
0
4.
0
5.
0
6.
0
7.
0
8.
0
9.
0
10
.0
11
.0
12
.0
13
.0
14
.0
15
.0
16
.0
17
.0
18
.0
19
.0
20
.0
21
.0
22
.0
23
.0
24
.0
25
.0
1.000
ICC Maximum
Table 10. IMVP-III Deep Sleep State Voltage Regulator Tolerances for Maximum Performance
Mode (VID = 1.30 V, VID Offset = 4.62%)
VCC Nominal
(V)
VCC Static Min
(V)
VCC Static Max
(V)
VCC Transient
Min (V)
VCC Transient
Max (V)
0.0
1.240
1.215
1.265
1.195
1.285
1.0
1.238
1.213
1.263
1.193
1.283
2.0
1.236
1.211
1.261
1.191
1.281
3.0
1.234
1.209
1.259
1.189
1.279
4.0
1.232
1.207
1.257
1.187
1.277
5.0
1.230
1.205
1.255
1.185
1.275
6.0
1.228
1.203
1.253
1.183
1.273
7.0
1.226
1.201
1.251
1.181
1.271
8.0
1.224
1.199
1.249
1.179
1.269
9.0
1.222
1.197
1.247
1.177
1.267
10.0
1.220
1.195
1.245
1.175
1.265
ICC (A)
28
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Table 11. IMVP-III Deep Sleep State Voltage Regulator Tolerances for Battery Optimized Mode
(VID = 1.20 V, VID Offset = 4.62%)
ICC (A)
VCC Nominal
(V)
VCC Static Min
(V)
VCC Static Max
(V)
VCC Transient
Min (V)
VCC Transient
Max (V)
0.0
1.145
1.120
1.170
1.100
1.190
1.0
1.143
1.118
1.168
1.098
1.188
2.0
1.141
1.116
1.166
1.096
1.186
3.0
1.139
1.114
1.164
1.094
1.184
4.0
1.137
1.112
1.162
1.092
1.182
5.0
1.135
1.110
1.160
1.090
1.180
6.0
1.133
1.108
1.158
1.088
1.178
7.0
1.131
1.106
1.156
1.086
1.176
8.0
1.129
1.104
1.154
1.084
1.174
Figure 6. Illustration of Deep Sleep VCC Static and Transient Tolerances (VID Setting = 1.30 V)
Northwood Deep Sleep Load Line for VID = 1.30V
1.300
Transient Maximum
1.280
Static Maximum
1.260
Vcc Nominal
1.240
VCC
1.220
1.200
Static Minimum
1.180
Transient Minimum
1.160
1.140
1.120
0
1
2
3
4
5
6
7
8
9
10
Isb Maximum
Mobile Intel Pentium 4 Processor-M Datasheet
29
Electrical Specifications
Table 12. System Bus Differential BCLK Specifications
Notes1
Symbol
Parameter
Min
Typ
Max
Unit
Figure
VL
Input Low
Voltage
-0.150
0.000
N/A
V
10
VH
Input High
Voltage
0.660
0.710
0.850
V
10
VCROSS(abs)
Absolute
Crossing Point
0.250
N/A
0.550
V
10, 11
2,3,8
VCROSS(rel)
Relative
Crossing Point
V
10, 11
2,3,8,9
∆VCROSS
Range of
Crossing Points
N/A
N/A
0.140
V
10, 11
2,10
VOV
Overshoot
N/A
N/A
VH + 0.3
V
10
4
VUS
Undershoot
-0.300
N/A
N/A
V
10
5
VRBM
Ringback
Margin
0.200
N/A
N/A
V
10
6
VTM
Threshold
Margin
VCROSS - 0.100
N/A
VCROSS + 0.100
V
10
7
0.250 +
0.5(VHavg - 0.710)
N/A
0.550 +
0.5(VHavg - 0.710)
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. Crossing voltage is defined as the instantaneous voltage value when the rising edge of BCLK0 equals the
falling edge of BCLK1.
3. VHavg is the statistical average of the VH measured by the oscilloscope.
4. Overshoot is defined as the absolute value of the maximum voltage.
5. Undershoot is defined as the absolute value of the minimum voltage.
6. Ringback Margin is defined as the absolute voltage difference between the maximum Rising Edge Ringback
and the maximum Falling Edge Ringback.
7. Threshold Region is defined as a region entered around the crossing point voltage in which the differential
receiver switches. It includes input threshold hysteresis.
8. The crossing point must meet the absolute and relative crossing point specifications simultaneously.
9. VHavg can be measured directly using "Vtop" on Agilent* scopes and "High" on Tektronix* scopes.
10.∆VCROSS is defined as the total variation of all crossing voltages as defined in note 2.
30
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Table 13. AGTL+ Signal Group DC Specifications
Notes1
Symbol
Parameter
Min
Max
Unit
GTLREF
Reference Voltage
2/3 Vcc - 2%
2/3 Vcc + 2%
V
VIH
Input High Voltage
1.10*GTLREF
VCC
V
2,6
VIL
Input Low Voltage
0.0
0.9*GTLREF
V
3,4,6
VOH
Output High Voltage
N/A
Vcc
V
7
IOL
Output Low Current
N/A
50
mA
6
IHI
Pin Leakage High
N/A
100
µA
8
ILO
Pin Leakage Low
N/A
500
µA
9
RON
Buffer On Resistance
7
11
Ω
5
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. VIL is defined as the maximum voltage level at a receiving agent that will be interpreted as a logical low value.
3. VIH is defined as the minimum voltage level at a receiving agent that will be interpreted as a logical high
value.
4. VIH and VOH may experience excursions above VCC. However, input signal drivers must comply with the
signal quality specifications in Section 3.
5. Refer to processor I/O Buffer Models for I/V characteristics.
6. The VCC referred to in these specifications is the instantaneous VCC.
7. Vol max of 0.450 Volts is guaranteed when driving into a test load of 50 Ω as indicated in Figure 8.
8. Leakage to VSS with pin held at VCC.
9. Leakage to VCC with pin held at 300 mV.
Mobile Intel Pentium 4 Processor-M Datasheet
31
Electrical Specifications
Table 14. Asynchronous GTL+ Signal Group DC Specifications
Symbol
VIH
VIL
Unit
Notes1
V
3, 4, 5
0.9*GTLREF
V
5
Parameter
Min
Max
Input High Voltage
1.10*GTLREF
VCC
0
Asynch GTL+
Input Low Voltage
Asynch. GTL+
VOH
Output High Voltage
N/A
VCC
V
2, 3, 4
IOL
Output Low Current
N/A
50
mA
6, 8
IHI
Pin Leakage High
N/A
100
µA
9
ILO
Pin Leakage Low
N/A
500
µA
10
7
11
Ω
5, 7
Ron
Buffer On Resistance
Asynch GTL+
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. All outputs are open-drain.
3. VIH and VOH may experience excursions above VCC. However, input signal drivers must comply with the
signal quality specifications in Section 3.
4. The VCC referred to in these specifications refers to instantaneous VCC.
5. This specification applies to the asynchronous GTL+ signal group.
6. The maximum output current is based on maximum current handling capability of the buffer and is not
specified into the test load shown in Figure 8.
7. Refer to the processor I/O Buffer Models for I/V characteristics.
8. Vol max of 0.270 Volts is guaranteed when driving into a test load of 50 Ω as indicated in Figure 8 for the
Asynchronous GTL+ signals.
9. Leakage to VSS with pin held at VCC.
10.Leakage to VCC with pin held at 300 mV.
32
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Table 15. PWRGOOD and TAP Signal Group DC Specifications
Symbol
Parameter
Min
Max
Unit
Notes1
VHYS
Input Hysteresis
200
300
mV
8
VT+
Input Low to High
Threshold Voltage
1/2*(Vcc+VHYS_MIN)
1/2*(Vcc+VHYS_MAX)
V
5
VT-
Input High to Low
Threshold Voltage
1/2*(Vcc-VHYS_MAX)
1/2*(Vcc-VHYS_MIN)
V
5
VOH
Output High Voltage
N/A
VCC
V
2,3,5
IOL
Output Low Current
N/A
40
mA
6,7
IHI
Pin Leakage High
N/A
100
µA
9
ILO
Pin Leakage Low
N/A
500
µA
10
Ron
Buffer On Resistance
8.75
13.75
Ω
4
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. All outputs are open-drain.
3. TAP signal group must comply with the signal quality specifications in Section 3.
4. Refer to I/O Buffer Models for I/V characteristics.
5. The VCC referred to in these specifications refers to instantaneous VCC.
6. The maximum output current is based on maximum current handling capability of the buffer and is not
specified into the test load shown if Figure 8.
7. Vol max of 0.320 Volts is guaranteed when driving into a test load of 50 Ohms as indicated in Figure 8 for the
TAP Signals.
8. VHYS represents the amount of hysteresis, nominally centered about 1/2 Vcc for all TAP inputs.
9. Leakage to VSS with pin held at VCC.
10.Leakage to VCC with pin held at 300 mV.
Table 16. ITPCLKOUT[1:0] DC Specifications
Symbol
Parameter
Min
Max
Unit
Notes1
Ron
Buffer On Resistance
27
46
Ω
2,3
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. These parameters are not tested and are based on design simulations.
3. See Figure 7 for ITPCLKOUT[1:0] output buffer diagram.
Mobile Intel Pentium 4 Processor-M Datasheet
33
Electrical Specifications
Figure 7. ITPCLKOUT[1:0] Output Buffer Diagram
Vcc
Ron
To Debug Port
Processor Package
Rext
NOTES:
1. See Table 16 for range of Ron.
2. The Vcc referred to in this figure is the instantaneous Vcc.
3. Refer to the appropriate platform design guidelines for the value of Rext.
Table 17. BSEL [1:0] and VID[4:0] DC Specifications
Symbol
Parameter
Min
Max
Unit
Notes1
Ron
(BSEL)
Buffer On Resistance
9.2
14.3
Ω
2
Ron
(VID)
Buffer On Resistance
7.8
12.8
Ω
2
IHI
Pin Leakage Hi
N/A
100
µA
3
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. These parameters are not tested and are based on design simulations.
3. Leakage to Vss with pin held at 2.50 V.
2.12
AGTL+ System Bus Specifications
Routing topology recommendations may be found in the Mobile Intel Pentium 4 Processor-M
and Intel 845MP/845MZ Chipset Platform Design Guide. Termination resistors are not required
for most AGTL+ signals, as these are integrated into the processor silicon.
Valid high and low levels are determined by the input buffers which compare a signal’s voltage
with a reference voltage called GTLREF (known as VREF in previous documentation).
Table 18 lists the GTLREF specifications. The AGTL+ reference voltage (GTLREF) should be
generated on the system board using high precision voltage divider circuits. It is important that the
system board impedance is held to the specified tolerance, and that the intrinsic trace capacitance
34
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
for the AGTL+ signal group traces is known and well-controlled. For more details on platform
design see the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform
Design Guide.
Table 18. AGTL+ Bus Voltage Definitions
Symbol
Parameter
Units
Notes1
Min
Typ
Max
2/3 VCC -2%
2/3 VCC
2/3 VCC +2%
V
2, 3, 6
GTLREF
Bus Reference
Voltage
RTT
Termination
Resistance
45
50
55
Ω
4
COMP[1:0]
COMP
Resistance
50.49
51
51.51
Ω
5
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. The tolerances for this specification have been stated generically to enable the system designer to calculate
the minimum and maximum values across the range of VCC.
3. GTLREF should be generated from VCC by a voltage divider of 1% tolerance resistors or 1% tolerance
matched resistors. Refer to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset
Platform Design Guide for implementation details.
4. RTT is the on-die termination resistance measured at VOL of the AGTL+ output driver. Refer to processor I/O
buffer models for I/V characteristics.
5. COMP resistance must be provided on the system board with 1% tolerance resistors. See the Mobile Intel
Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design Guide for implementation
details.
6. The VCC referred to in these specifications is the instantaneous VCC.
2.13
System Bus AC Specifications
The processor system bus timings specified in this section are defined at the processor core
(pads). See Section 5.2 for the Mobile Intel Pentium 4 Processor-M pin signal definitions.
Table 19 through Table 26 list the AC specifications associated with the processor system bus.
All AGTL+ timings are referenced to GTLREF for both “0” and “1” logic levels unless otherwise
specified.
The timings specified in this section should be used in conjunction with the I/O buffer models
provided by Intel. These I/O buffer models, which include package information, are available for
the Mobile Intel Pentium 4 Processor-M in IBIS format. AGTL+ layout guidelines are also
available in the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset
Platform Design Guide.
Unless specified otherwise, all Mobile Intel Pentium 4 Processor-M AC specifications are at TJ =
100°C. Care should be taken to read all notes associated with a particular timing parameter.
Mobile Intel Pentium 4 Processor-M Datasheet
35
Electrical Specifications
Table 19. System Bus Differential Clock Specifications
T# Parameter
Min
Nom
System Bus Frequency
T1: BCLK[1:0] Period
10.0
T2: BCLK[1:0] Period Stability
Max
Unit
100
MHz
10.2
ns
200
ps
Notes1
Figure
10
2
3
T3: BCLK[1:0] High Time
3.94
5
6.12
ns
10
T4: BCLK[1:0] Low Time
3.94
5
6.12
ns
10
T5: BCLK[1:0] Rise Time
175
700
ps
10
4
T6: BCLK[1:0] Fall Time
175
700
ps
10
4
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. The period specified here is the average period. A given period may vary from this specification as governed
by the period stability specification (T2).
3. In this context, period stability is defined as the worst case timing difference between successive crossover
voltages. In other words, the largest absolute difference between adjacent clock periods must be less than
the period stability.
4. Slew rate is measured between the 35% and 65% points of the clock swing (VL to VH).
.
Table 20. System Bus Common Clock AC Specifications
T# Parameter
Notes1,2,3
Min
Max
Unit
Figure
T10: Common Clock Output Valid Delay
0.12
1.55
ns
12
4
T11: Common Clock Input Setup Time
0.65
ns
12
5
T12: Common Clock Input Hold Time
0.40
ns
12
5
ms
13
6, 7, 8
T13: RESET# Pulse Width
1
10
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. Not 100% tested. Specified by design characterization.
3. All common clock AC timings for AGTL+ signals are referenced to the Crossing Voltage (VCROSS) of the
BCLK[1:0] at rising edge of BCLK0. All common clock AGTL+ signal timings are referenced at GTLREF at the
processor core.
4. Valid delay timings for these signals are specified into the test circuit described in Figure 8 and with GTLREF
at 2/3 VCC ± 2%.
5. Specification is for a minimum swing defined between AGTL+ VIL_MAX to VIH_MIN. This assumes an edge rate
of 0.4 V/ns to 4.0 V/ns.
6. RESET# can be asserted asynchronously, but must be deasserted synchronously.
7. This should be measured after VCC and BCLK[1:0] become stable.
8. Maximum specification applies only while PWRGOOD is asserted.
.
36
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Table 21. System Bus Source Synch AC Specifications AGTL+ Signal Group
Max
Unit
Figure
Notes1,2,3,4
1.20
ns
14, 15
5
0.85
ns
15
5, 8
T22: TVAD: Source Synchronous Data
Output Valid After Strobe
0.85
ns
15
5, 9
T23: TVBA: Source Synchronous
Address Output Valid Before Strobe
1.88
ns
14
5, 8
T24: TVAA: Source Synchronous
Address Output Valid After Strobe
1.88
ns
14
5, 9
T25: TSUSS: Source Synchronous Input
Setup Time to Strobe
0.21
ns
14, 15
6
T26: THSS: Source Synchronous Input
Hold Time to Strobe
0.21
ns
14, 15
6
T27: TSUCC: Source Synchronous Input
Setup Time to BCLK[1:0]
0.65
ns
14, 15
7
T# Parameter
Min
T20: Source Synchronous Data Output
Valid Delay (first data/address only)
0.20
T21: TVBD: Source Synchronous Data
Output Valid Before Strobe
Typ
T28: TFASS: First Address Strobe to
Second Address Strobe
1/2
BCLK
14
10
T29: TFDSS: First Data Strobe to
Subsequent Strobes
n/4
BCLK
15
11, 12
13
T30: Data Strobe ‘n’ (DSTBN#) Output
valid Delay
8.80
10.20
ns
15
T31: Address Strobe Output Valid
Delay
2.27
4.23
ns
14
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies and cache sizes.
2. Not 100% tested. Specified by design characterization.
3. All source synchronous AC timings are referenced to their associated strobe at GTLREF. Source
synchronous data signals are referenced to the falling edge of their associated data strobe. Source
synchronous address signals are referenced to the rising and falling edge of their associated address strobe.
All source synchronous AGTL+ signal timings are referenced to GTLREF at the processor core.
4. Unless otherwise noted these specifications apply to both data and address timings.
5. Valid delay timings for these signals are specified into the test circuit described in Figure 8 and with GTLREF
at 2/3 VCC ± 2%.
6. Specification is for a minimum swing defined between AGTL+ VIL_MAX to VIH_MIN. This assumes an edge rate
of 0.3 V/ns to 4.0V /ns.
7. All source synchronous signals must meet the specified setup time to BCLK as well as the setup time to each
respective strobe.
8. This specification represents the minimum time the data or address will be valid before its strobe. Refer to the
Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design Guide for more
information on the definitions and use of these specifications.
9. This specification represents the minimum time the data or address will be valid after its strobe. Refer to the
Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design Guide for more
information on the definitions and use of these specifications.
10.The rising edge of ADSTB# must come approximately 1/2 BCLK period (5 ns) after the falling edge of
ADSTB#.
11.For this timing parameter, n = 1, 2, and 3 for the second, third, and last data strobes respectively.
12.The second data strobe (falling edge of DSTBn#) must come approximately 1/4 BCLK period (2.5 ns) after
the first falling edge of DSTBp#. The third data strobe (falling edge of DSTBp#) must come approximately 2/4
BCLK period (5 ns) after the first falling edge of DSTBp#. The last data strobe (falling edge of DSTBn#) must
come approximately 3/4 BCLK period (7.5 ns) after the first falling edge of DSTBp#.
13.This specification applies only to DSTBN[3:0]# and is measured to the second falling edge of the strobe.
Mobile Intel Pentium 4 Processor-M Datasheet
37
Electrical Specifications
Table 22. Miscellaneous Signals AC Specifications
T# Parameter
Min
T35: Asynch GTL+ Input Pulse Width
2
T36: PWRGOOD to RESET# de-assertion
time
1
T37: PWRGOOD Inactive Pulse Width
T38: PROCHOT# pulse width
Max
Notes1,2,3,6
Figure
BCLKs
10
ms
16
10
BCLKs
16
4
500
us
18
5
0.5
s
19
5
BCLKs
20
T39: THERMTRIP# to Vcc Removal
T40: FERR# Valid Delay from STPCLK#
deassertion
Unit
0
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. All AC timings for the Asynch GTL+ signals are referenced to the BCLK0 rising edge at Crossing Voltage. All
Asynch GTL+ signal timings are referenced at GTLREF. PWRGOOD is referenced to the BCLK0 rising edge
at 0.5*VCC
3. These signals may be driven asynchronously.
4. Refer to the PWRGOOD definition for more details regarding the behavior of this signal.
5. Length of assertion for PROCHOT# does not equal internal clock modulation time. Time is allocated after the
assertion and before the deassertion of PROCHOT# for the processor to complete current instruction
execution. This specification refers to PROCHOT# when asserted by the processor. There are no pulse width
requirements for when PROCHOT# is asserted by the system.
6. See Section 7.2 for additional timing requirements for entering and leaving the low power states.
Table 23. System Bus AC Specifications (Reset Conditions)
T# Parameter
Min
T45: Reset Configuration Signals (A[31:3]#,
BR0#, INIT#, SMI#) Setup Time
4
T46: Reset Configuration Signals (A[31:3]#,
BR0#, INIT#, SMI#) Hold Time
2
Max
20
Unit
Figure
Notes
BCLKs
13
1
BCLKs
13
2
NOTES:
1. Before the deassertion of RESET#.
2. After clock that deasserts RESET#.
38
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Table 24. TAP Signals AC Specifications
Parameter
Min
T55: TCK Period
Max
60.0
Unit
Figure
ns
9
Notes1,2,3
T56: TCK Rise Time
10.0
ns
9
4
T57: TCK Fall Time
10.0
ns
9
4
T58: TMS Rise Time
8.5
ns
9
4
T59: TMS Fall Time
8.5
ns
9
4, 9
T61: TDI Setup Time
0
ns
21
5, 7
T62: TDI Hold Time
3
ns
21
5, 7
ns
21
6
TCK
18
8, 9
T63: TDO Clock to Output Delay
3.5
T64: TRST# Assert Time
2
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. Not 100% tested. Specified by design characterization.
3. All AC timings for the TAP signals are referenced to the TCK signal at 0.5*VCC at the processor pins. All TAP
signal timings (TMS, TDI, etc) are referenced at 0.5*VCC at the processor pins.
4. Rise and fall times are measured from the 20% to 80% points of the signal swing.
5. Referenced to the rising edge of TCK.
6. Referenced to the falling edge of TCK.
7. Specifications for a minimum swing defined between TAP VT- to VT+. This assumes a minimum edge rate of
0.5 V/ns
8. TRST# must be held asserted for 2 TCK periods to be guaranteed that it is recognized by the processor.
9. It is recommended that TMS be asserted while TRST# is being deasserted.
Table 25. ITPCLKOUT[1:0] AC Specifications
Parameter
T65: ITPCLKOUT Delay
T66: Slew Rate
Max
Unit
Figure
Notes1,2
400
560
ps
22
3
2
8
V/ns
Min
Typ
T67: ITPCLKOUT[1:0] High
Time
3.89
5
6.17
ns
T68: ITPCLKOUT[1:0] Low
Time
3.89
5
6.17
ns
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. These parameters are not tested and are based on design simulations.
3. This delay is from rising edge of BCLK0 to the falling edge of ITPCLK0.
Mobile Intel Pentium 4 Processor-M Datasheet
39
Electrical Specifications
.
Table 26. Stop Grant/Sleep/Deep Sleep/Enhanced Intel SpeedStep Technology AC
Specifications
T# Parameter
Min
Max
Unit
Figure
T70: SLP# Signal Hold Time from Stop Grant
Cycle Completion
100
BCLKs
23
T71: Input Signals Stable to SLP# Assertion
10
BCLKs
23, 24
T72: SLP# to DPSLP# Assertion
10
BCLKs
23
T73: Deep Sleep PLL Lock Latency
0
µs
23
T74: SLP# Hold Time from PLL Lock
0
ns
23
T75: STPCLK# Hold Time from SLP#
Deassertion
10
BCLKs
23
T76: Input Signal Hold Time from SLP#
Deassertion
10
BCLKs
23, 24
T77: VID[4:0] Output Valid Delay from DPSLP#
Assertion
0
µs
24
30
10
Notes
1
2
NOTES:
1. Input signals other than RESET# must be held constant in the Sleep state.
2. The BCLK can be stopped after DPSLP# is asserted. The BCLK must be turned on and within specification
before DPSLP# is deasserted.
.
2.14
Processor AC Timing Waveforms
The following figures are used in conjunction with the AC timing tables, Table 19 through Table
26.
For Figure 9 through Figure 24, the following apply:
NOTES:
1. All common clock AC timings for AGTL+ signals are referenced to the Crossing Voltage (VCROSS) of the
BCLK[1:0] at rising edge of BCLK0. All common clock AGTL+ signal timings are referenced at GTLREF at the
processor core.
2. All source synchronous AC timings for AGTL+ signals are referenced to their associated strobe (address or
data) at GTLREF. Source synchronous data signals are referenced to the falling edge of their associated data
strobe. Source synchronous address signals are referenced to the rising and falling edge of their associated
address strobe. All source synchronous AGTL+ signal timings are referenced at GTLREF at the processor
core silicon.
3. All AC timings for AGTL+ strobe signals are referenced to BCLK[1:0] at VCROSS. All AGTL+ strobe signal
timings are referenced at GTLREF at the processor core silicon.
4. All AC timings for the TAP signals are referenced to the TCK signal at 0.5*VCC at the processor pins. All TAP
signal timings (TMS, TDI, etc.) are referenced at 0.5*VCC at the processor pins.
The circuit used to test the AC specifications is shown in Figure 8.
40
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Figure 8. AC Test Circuit
VCC
VCC
Rload= 50 ohms
420 mils, 50 ohms, 169 ps/in
2.4nH
1.2pF
AC Timings test measurements made here.
Figure 9. TCK Clock Waveform
V2
V3
V1
tr = T56, T58 (Rise Time)
tf = T57, T59 (Fall Time)
tp = T55 (TCK Period)
Mobile Intel Pentium 4 Processor-M Datasheet
V1,V2: For rise and fall times, TCK is measured
between 20% to 80% points on the waveform
V3: TCK is referenced to 0.5*Vcc
41
Electrical Specifications
.
Figure 10. Differential Clock Waveform
Tph
Overshoot
BCLK1
VH
Rising Edge
Ringback
Crossing
Voltage
Threshold
Region
Crossing
Voltage
Ringback
Margin
Falling Edge
Ringback,
BCLK0
VL
Undershoot
Tpl
Tp
Tp = T1 (BCLK[1:0] period)
T2 = BCLK[1:0] Period stability (not shown)
Tph =T3 (BCLK[1:0] pulse high time)
Tpl = T4 (BCLK[1:0] pulse low time)
T5 = BCLK[1:0] rise time through the threshold region
T6 = BCLK[1:0] fall time through the threshold region
42
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Figure 11. Differential Clock Crosspoint Specification
Crosspoint Specification
650
600
Crossing
CrossingPoint
Point(mV)
(V)
550
550 mV
500
450
550 + 0.5 (VHavg - 710)
400
250 + 0.5 (VHavg - 710)
350
300
250
250 mV
200
660 670 680 690 700 710 720 730 740 750 760 770 780 790 800 810 820 830 840 850
VHavg
Vhavg(V)
(mV)
Figure 12. System Bus Common Clock Valid Delay Timings
T0
T1
T2
BCLK1
BCLK0
TP
Common Clock
Signal (@ driver)
valid
valid
TQ
Common Clock
Signal (@ receiver)
TR
valid
TP = T10: TCO (Data Valid Output Delay)
TQ = T11: TSU (Common Clock Setup)
TR = T12: TH (Common Clock Hold Time)
Mobile Intel Pentium 4 Processor-M Datasheet
43
Electrical Specifications
Figure 13. System Bus Reset and Configuration Timings
BCLK
Tt
Reset
Tv
Tx
Tw
Configuration
Valid
A[31:3], SMI#,
INIT#, BR[3:0]#
Tv = T13 (RESET# Pulse Width)
Tw = T45 (Reset Configuration Signals Setup TIme)
Tx = T46 (Reset Configuration Signals Hold TIme)
Figure 14. Source Synchronous 2X (Address) Timings
T1
2.5 ns
5.0 ns
T2
7.5 ns
BCLK1
BCLK0
TP
ADSTB# (@ driver)
TR
TH
A# (@ driver)
valid
TJ
TH
TJ
valid
TS
ADSTB# (@ receiver)
TK
A# (@ receiver)
valid
valid
TN
TM
TH = T23: Source Sync. Address Output Valid Before Address Strobe
TJ = T24: Source Sync. Address Output Valid After Address Strobe
TK = T27: Source Sync. Input Setup to BCLK
TM = T26: Source Sync. Input Hold Time
TN = T25: Source Sync. Input Setup Time
TP = T28: First Address Strobe to Second Address Strobe
TS = T20: Source Sync. Output Valid Delay
TR = T31: Address Strobe Output Valid Delay
44
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Figure 15. Source Synchronous 4X Timings
T0
T1
2.5 ns
5.0 ns
T2
7.5 ns
BCLK1
BCLK0
DSTBp# (@ driver)
TH
DSTBn# (@ driver)
TA
TB TA
TD
D# (@ driver)
DSTBp# (@ receiver)
TJ
DSTBn# (@ receiver)
TC
D# (@ receiver)
TE TG TE TG
TA = T21: Source Sync. Data Output Valid Delay Before Data Strobe
TB = T22: Source Sync. Data Output Valid Delay After Data Strobe
TC = T27: Source Sync. Setup Time to BCLK
TD = T30: Source Sync. Data Strobe 'N' (DSTBN#) Output Valid Delay
TE = T25: Source Sync. Input Setup Time
TG = T26: Source Sync. Input Hold Time
TH = T29: First Data Strobe to Subsequent Strobes
TJ = T20: Source Sync. Data Output Valid Delay
Mobile Intel Pentium 4 Processor-M Datasheet
45
Electrical Specifications
Figure 16. Power Up Sequence
BCLK
Vcc
PWRGOOD
Tc
Td
RESET#
VCCVID
Ta
Tb
VID_GOOD
VID[4:0],
BSEL[1:0]
Ta= 1us minimum (VCCVID > 1V to VID_GOOD high)
Tb= 50ms maximum (VID_GOOD to Vcc valid maximum time)
Tc= T37 (PWRGOOD inactive pulse width)
Td= T36 (PWRGOOD to RESET# de-assertion time)
Note: VID_GOOD is not a processor signal. This signal is routed to the
output enable pin of the voltage regluator control silicon. For more
information on implementation refer to the Intel Mobile Northwood
Processor and Intel 845MP Platform RDDP.
Figure 17. Power Down Sequence
Vcc
PWRGOOD
VCCVID
VID_GOOD
VID[4:0]
Note: VID_GOOD is not a processor signal. This signal is routed to the
output enable pin of the voltage regluator control silicon. For more
information on implementation refer to the Intel Mobile Northwood
Processor and Intel 845MP Platform RDDP.
1. This timing diagram is not intended to show specific times. Instead a
general ordering of events with respect to time should be observed.
2. When VCCVID is less than 1V, VID_GOOD must be low.
3. Vcc must be disabled before VID[4:0] becomes invalid.
4. VCCVID and Vcc regulator can be disabled simultaneously
46
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Figure 18. Test Reset Timings
1.25V
TRST#
Tq
Tq = T64 (TRST# Pulse Width), V=0.5*Vcc
Tq = T37 (TRST#
Pulse Width)
T38 (PROCHOT# Pulse Width), V=GTLREF
PCB-773
Figure 19. THERMTRIP# to Vcc Timing
T39
THERMTRIP#
Vcc
T39 < 0.5 seconds
Note: THERMTRIP# is undefined when RESET# is active
Figure 20. FERR#/PBE# Valid Delay Timing
BCLK
SG
Ack
system bus
STPCLK#
Ta
FERR#/
PBE#
FERR#
undefined
PBE#
undefined
FERR#
Ta = T40 (FERR# Valid Delay from STPCLK# Deassertion)
Note: FERR#/PBE# is undefined from STPCLK# assertion until the stop grant acknowledge is driven on the processor system
bus. FERR#/PBE# is also undefined for a period of Ta from STPCLK# deassertion. Inside these undefined regions the PBE#
signal is driven. FERR# is driven at all other times.
Mobile Intel Pentium 4 Processor-M Datasheet
47
Electrical Specifications
Figure 21. TAP Valid Delay Timing
V
TCK
Tx
Ts
Th
Signal
V Valid
Tx = T63 (Valid Time)
Ts = T61 (Setup Time)
Th = T62 (Hold Time)
V = 0.5 * Vcc
Figure 22. ITPCLKOUT Valid Delay Timing
Tx
BCLK
ITPCLKOUT
T65 = Tx = BCLK input to ITPCLKOUT output delay
48
Mobile Intel Pentium 4 Processor-M Datasheet
Electrical Specifications
Figure 23. Stop Grant/Sleep/Deep Sleep Timing
Stop
Grant
Normal
Sleep
Deep Sleep
Stop
Grant
Sleep
Normal
BCLK[1:0]
DPSLP#
Tv
STPCLK#
Ty
CPU bus
stpgnt
Tw
Tt
Tx
SLP#
Tu
Compatibility
Signals
Changing
Tz
Frozen
Changing
V0011-02
Tt = T70 (Stop Grant Acknowledge Bus Cycle Completion to SLP# Assertion Delay)
Tu = T71 (Input Signals Stable to SLP# assertion requirement)
Tv = T72 (SLP# to DPSLP# assertion)
Tw = T73 (Deep Sleep PLL lock latency)
Tx = T74 (SLP# Hold Time)
Ty = T75 (STPCLK# Hold Time)
Tz = T76 (Input Signal Hold Time)
Mobile Intel Pentium 4 Processor-M Datasheet
49
Electrical Specifications
Figure 24. Enhanced Intel SpeedStep Technology/Deep Sleep Timing
BCLK[1:0]
SLP#
Th
TX
DPSLP#
TS
GHI#
VID[4:0]
GHI# stable
previous VID
next VID
V0036-04
TS = T71 (GHI# Input Setup to SLP# Assertion)
Th = T76 (GHI# Input signal Hold Time from SLP# De-assertion)
TX = T77 (VID[4:0] Output Valid Delay from DPSLP# Assertion)
50
Mobile Intel Pentium 4 Processor-M Datasheet
System Bus Signal Quality Specifications
3.
System Bus Signal Quality Specifications
Source synchronous data transfer requires the clean reception of data signals and their associated
strobes. Ringing below receiver thresholds, non-monotonic signal edges, and excessive voltage
swing will adversely affect system timings. Ringback and signal non-monotinicity cannot be
tolerated since these phenomena may inadvertently advance receiver state machines. Excessive
signal swings (overshoot and undershoot) are detrimental to silicon gate oxide integrity and can
cause device failure if absolute voltage limits are exceeded. Additionally, overshoot and
undershoot can cause timing degradation due to the build up of inter-symbol interference (ISI)
effects. For these reasons, it is important that the designer work to achieve a solution that provides
acceptable signal quality across all systematic variations encountered in volume manufacturing.
This section documents signal quality metrics used to derive topology and routing guidelines
through simulation and for interpreting results for signal quality measurements of actual designs.
3.1
System Bus Clock (BCLK) Signal Quality Specifications
and Measurement Guidelines
Table 27 describes the signal quality specifications at the processor pads for the processor system
bus clock (BCLK) signals. Figure 25 describes the signal quality waveform for the system bus
clock at the processor pads.
Table 27. BCLK Signal Quality Specifications
Parameter
Min
Max
Unit
Figure
BCLK[1:0] Overshoot
N/A
0.30
V
25
BCLK[1:0] Undershoot
N/A
0.30
V
25
BCLK[1:0] Ringback Margin
0.20
N/A
V
25
BCLK[1:0] Threshold Region
N/A
0.10
V
25
Notes1
2
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all Mobile Intel Pentium 4 Processor-M
frequencies.
2. The rising and falling edge ringback voltage specified is the minimum (rising) or maximum (falling) absolute
voltage the BCLK signal can dip back to after passing the VIH (rising) or VIL (falling) voltage limits. This
specification is an absolute value.
Mobile Intel Pentium 4 Processor-M Datasheet
51
System Bus Signal Quality Specifications
Figure 25. BCLK Signal Integrity Waveform
Overshoot
BCLK1
VH
Rising Edge
Ringback
Crossing
Voltage
Threshold
Region
Crossing
Voltage
Ringback
Margin
Falling Edge
Ringback,
BCLK0
VL
Undershoot
3.2
System Bus Signal Quality Specifications and
Measurement Guidelines
Various scenarios have been simulated to generate a set of AGTL+ layout guidelines which are
available in the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset
Platform Design Guide.
Table 28 and Table 29 provides the signal quality specifications for all processor signals for use in
simulating signal quality at the processor core silicon (pads).
Mobile Intel Pentium 4 Processor-M maximum allowable overshoot and undershoot specifications
for a given duration of time are detailed in Table 30 through Table 33. Figure 26 shows the system
bus ringback tolerance for low-to-high transitions and Figure 27 shows ringback tolerance for
high-to-low transitions.
Table 28. Ringback Specifications for AGTL+ and Asynchronous GTL+ Signal Groups
Signal Group
Transition
Maximum Ringback
(with Input Diodes Present)
Unit
Figure
Notes
All Signals
0→
1
GTLREF + 10%
V
26
1,2,3,4,5,6,7
All Signals
1→
0
GTLREF - 10%
V
27
1,2,3,4,5,6,7
NOTES:
1. All signal integrity specifications are measured at the processor silicon (pads).
2. Unless otherwise noted, all specifications in this table apply to all Mobile Intel Pentium 4 Processor-M
frequencies.
3. Specifications are for the edge rate of 0.3 - 4.0 V/ns.
4. All values specified by design characterization.
5. Please see Section 3.3 for maximum allowable overshoot.
6. Ringback between GTLREF + 10% and GTLREF - 10% is not supported.
7. Intel recommends simulations not exceed a ringback value of GTLREF +/- 200 mV to allow margin for other
sources of system noise.
52
Mobile Intel Pentium 4 Processor-M Datasheet
System Bus Signal Quality Specifications
Table 29. Ringback Specifications for PWRGOOD Input and TAP Signal Groups
Signal Group
Transition
Maximum Ringback
(with Input Diodes Present)
Unit
Figure
TAP and PWRGOOD
0→1
Vt+(max) TO Vt-(max)
V
28
1,2,3,4
TAP and PWRGOOD
1→0
Vt-(min) TO Vt+(min)
V
29
1,2,3,4
Notes
NOTES:
1. All signal integrity specifications are measured at the processor silicon.
2. Unless otherwise noted, all specifications in this table apply to all Mobile Intel Pentium 4 Processor-M
frequencies.
3. Please see Section 3.3 for maximum allowable overshoot.
4. Please see Section 2.11 for the DC specifications.
Figure 26. Low-to-High System Bus Receiver Ringback Tolerance
VCC
+10% GTLREF
GTLREF
-10% GTLREF
Noise
Margin
VSS
Figure 27. High-to-Low System Bus Receiver Ringback Tolerance
VCC
+10% GTLREF
GTLREF
-10% GTLREF
Noise
Margin
VSS
Mobile Intel Pentium 4 Processor-M Datasheet
53
System Bus Signal Quality Specifications
Figure 28. Low-to-High System Bus Receiver Ringback Tolerance for PWRGOOD and TAP
Buffers
Vcc
Threshold Region to switch
receiver to a logic 1.
Vt+ (max)
Vt+ (min)
0.5 * Vcc
Vt- (max)
Allowable Ringback
Vss
Figure 29. High-to-Low System Bus Receiver Ringback Tolerance for PWRGOOD and TAP
Buffers
Vcc
Allowable Ringback
Vt+ (min)
0.5 * Vcc
Vt- (max)
Vt- (min)
Threshold Region to switch
receiver to a logic 0.
Vss
54
Mobile Intel Pentium 4 Processor-M Datasheet
System Bus Signal Quality Specifications
3.3
System Bus Signal Quality Specifications and
Measurement Guidelines
3.3.1
Overshoot/Undershoot Guidelines
Overshoot (or undershoot) is the absolute value of the maximum voltage above the nominal high
voltage (or below VSS) as shown in Figure 30. The overshoot guideline limits transitions beyond
VCC or VSS due to the fast signal edge rates. The processor can be damaged by repeated overshoot
or undershoot events on any input, output, or I/O buffer if the charge is large enough (i.e., if the
over/undershoot is great enough). Determining the impact of an overshoot/undershoot condition
requires knowledge of the magnitude, the pulse direction, and the activity factor (AF). Permanent
damage to the processor is the likely result of excessive overshoot/undershoot.
When performing simulations to determine impact of overshoot and undershoot, ESD diodes must
be properly characterized. ESD protection diodes do not act as voltage clamps and will not provide
overshoot or undershoot protection. ESD diodes modelled within Intel I/O buffer models do not
clamp undershoot or overshoot and will yield correct simulation results. If other I/O buffer models
are being used to characterize the Mobile Intel Pentium 4 Processor-M system bus, care must be
taken to ensure that ESD models do not clamp extreme voltage levels. Intel I/O buffer models also
contain I/O capacitance characterization. Therefore, removing the ESD diodes from an I/O buffer
model will impact results and may yield excessive overshoot/undershoot.
3.3.2
Overshoot/Undershoot Magnitude
Magnitude describes the maximum potential difference between a signal and its voltage reference
level. For the Mobile Intel Pentium 4 Processor-M both are referenced to VSS. It is important to
note that overshoot and undershoot conditions are separate and their impact must be determined
independently.
Overshoot/undershoot magnitude levels must observe the absolute maximum specifications listed
in Table 30 through Table 33. These specifications must not be violated at any time regardless of
bus activity or system state. Within these specifications are threshold levels that define different
allowed pulse durations. Provided that the magnitude of the overshoot/undershoot is within the
absolute maximum specifications, the pulse magnitude, duration and activity factor must all be
used to determine if the overshoot/undershoot pulse is within specifications.
3.3.3
Overshoot/Undershoot Pulse Duration
Pulse duration describes the total time an overshoot/undershoot event exceeds the overshoot/
undershoot reference voltage (maximum overshoot = 1.700 V, maximum undershoot = -0.400 V).
The total time could encompass several oscillations above the reference voltage. Multiple
overshoot/undershoot pulses within a single overshoot/undershoot event may need to be measured
to determine the total pulse duration.
Mobile Intel Pentium 4 Processor-M Datasheet
55
System Bus Signal Quality Specifications
Note:
3.3.4
Oscillations below the reference voltage can not be subtracted from the total overshoot/undershoot
pulse duration.
Activity Factor
Activity Factor (AF) describes the frequency of overshoot (or undershoot) occurrence relative to a
clock. Since the highest frequency of assertion of any signal is every other clock, an AF = 1
indicates that the specific overshoot (or undershoot) waveform occurs EVERY OTHER clock
cycle. Thus, an AF = 0.01 indicates that the specific overshoot (or undershoot) waveform occurs
one time in every 200 clock cycles.
For source synchronous signals (address, data, and associated strobes), the activity factor is in
reference to the strobe edge, since the highest frequency of assertion of any source synchronous
signal is every active edge of its associated strobe. An AF = 1 indicates that the specific overshoot
(undershoot) waveform occurs every strobe cycle.
The specifications provided in Table 30 through Table 33 show the maximum pulse duration
allowed for a given overshoot/undershoot magnitude at a specific activity factor. Each table entry is
independent of all others, meaning that the pulse duration reflects the existence of overshoot/
undershoot events of that magnitude ONLY. A platform with an overshoot/undershoot that just
meets the pulse duration for a specific magnitude where the AF < 1, means that there can be no
other overshoot/undershoot events, even of lesser magnitude (note that if AF = 1, then the event
occurs at all times and no other events can occur).
3.3.5
Note:
1: Activity factor for AGTL+ signals is referenced to BCLK[1:0] frequency.
Note:
2: Activity factor for source synchronous (2x) signals is referenced to ADSTB[1:0]#.
Note:
3: Activity factor for source synchronous (4x) signals is referenced to DSTBP[3:0]# and
DSTBN[3:0]#.
Reading Overshoot/Undershoot Specification Tables
The overshoot/undershoot specification for the Mobile Intel Pentium 4 Processor-M is not a simple
single value. Instead, many factors are needed to determine what the over/undershoot specification
is. In addition to the magnitude of the overshoot, the following parameters must also be known: the
width of the overshoot (as measured above VCC) and the activity factor (AF). To determine the
allowed overshoot for a particular overshoot event, the following must be done:
1. Determine the signal group a particular signal falls into. If the signal is an AGTL+ signal
operating in the common clock domain, use Table 32. For AGTL+ signals operating in the 2x
source synchronous domain, use Table 31. For AGTL+ signals operating in the 4x source
synchronous domain, use Table 30. Finally, all other signals reside in the 100MHz domain
(asynchronous GTL+, TAP, etc.) and are referenced in Table 33.
2. Determine the magnitude of the overshoot (relative to VSS).
3. Determine the activity factor (how often does this overshoot occur?)
4. Next, from the appropriate specification table, determine the maximum pulse duration (in
nanoseconds) allowed.
5. Compare the specified maximum pulse duration to the signal being measured. If the pulse
duration measured is less than the pulse duration shown in the table, then the signal meets the
specifications.
56
Mobile Intel Pentium 4 Processor-M Datasheet
System Bus Signal Quality Specifications
The above procedure is similar for undershoot after the undershoot waveform has been converted
to look like an overshoot. Undershoot events must be analyzed separately from overshoot events as
they are mutually exclusive.
3.3.6
Conformance Determination to Overshoot/Undershoot Specifications
The overshoot/undershoot specifications listed in the following tables specify the allowable
overshoot/undershoot for a single overshoot/undershoot event. However most systems will have
multiple overshoot and/or undershoot events that each have their own set of parameters (duration,
AF and magnitude). While each overshoot on its own may meet the overshoot specification, when
you add the total impact of all overshoot events, the system may fail. A guideline to ensure a
system passes the overshoot and undershoot specifications is shown below.
1. Ensure no signal ever exceeds VCC or -0.25 V OR
2. If only one overshoot/undershoot event magnitude occurs, ensure it meets the over/undershoot
specifications in the following tables OR
3. If multiple overshoots and/or multiple undershoots occur, measure the worst case pulse
duration for each magnitude and compare the results against the AF = 1 specifications. If all of
these worst case overshoot or undershoot events meet the specifications (measured time <
specifications) in the table (where AF=1), then the system passes.
The following notes apply to Table 30 through Table 33.
NOTES:
1. Absolute Maximum Overshoot magnitude of 1.70 V must never be exceeded.
2. Absolute Maximum Overshoot is measured relative to VSS, Pulse Duration of overshoot is measured relative
to VCC.
3. Absolute Maximum Undershoot and Pulse Duration of undershoot is measured relative to VSS.
4. Ringback below VCC can not be subtracted from overshoots/undershoots.
5. Lesser undershoot does not allocate longer or larger overshoot.
6. OEM's are strongly encouraged to follow Intel provided layout guidelines.
7. All values specified by design characterization.
Table 30. Source Synchronous (400 MHz) AGTL+ Signal Group Overshoot/Undershoot
Tolerance
Absolute
Maximum
Overshoot
(V)
Absolute
Maximum
Undershoot
(V)
Pulse
Duration (ns)
AF = 1
Pulse
Duration (ns)
AF = 0.1
Pulse
Duration (ns)
AF = 0.01
1.700
-0.400
0.11
1.05
5.00
1.650
-0.350
0.24
2.40
5.00
1.600
-0.300
0.53
5.00
5.00
1.550
-0.250
1.19
5.00
5.00
1.500
-0.200
5.00
5.00
5.00
1.450
-0.150
5.00
5.00
5.00
1.400
-0.100
5.00
5.00
5.00
1.350
-0.050
5.00
5.00
5.00
Notes 1,2
NOTES:
1. These specifications are measured at the processor core silicon.
2. BCLK period is 10 ns.
Mobile Intel Pentium 4 Processor-M Datasheet
57
System Bus Signal Quality Specifications
Table 31. Source Synchronous (200 MHz) AGTL+ Signal Group Overshoot/Undershoot
Tolerance
Absolute
Maximum
Overshoot
(V)
Absolute
Maximum
Undershoot
(V)
Pulse
Duration (ns)
AF = 1
Pulse
Duration (ns)
AF = 0.1
Pulse
Duration (ns)
AF = 0.01
1.700
-0.400
0.21
2.10
10.00
1.650
-0.350
0.48
4.80
10.00
1.600
-0.300
1.05
10.00
10.00
1.550
-0.250
2.38
10.00
10.00
1.500
-0.200
10.00
10.00
10.00
1.450
-0.150
10.00
10.00
10.00
1.400
-0.100
10.00
10.00
10.00
1.350
-0.050
10.00
10.00
10.00
Notes 1,2
NOTES:
1. These specifications are measured at the processor core silicon.
2. BCLK period is 10 ns.
Table 32. Common Clock (100 MHz) AGTL+ Signal Group Overshoot/Undershoot Tolerance
Absolute
Maximum
Overshoot
(V)
Absolute
Maximum
Undershoot
(V)
Pulse
Duration (ns)
AF = 1
Pulse
Duration (ns)
AF = 0.1
Pulse
Duration (ns)
AF = 0.01
1.700
-0.400
0.42
4.20
20.00
1.650
-0.350
0.96
9.60
20.00
1.600
-0.300
2.10
20.00
20.00
1.550
-0.250
4.76
20.00
20.00
1.500
-0.200
20.00
20.00
20.00
1.450
-0.150
20.00
20.00
20.00
1.400
-0.100
20.00
20.00
20.00
1.350
-0.050
20.00
20.00
20.00
Notes 1,2
NOTES:
1. These specifications are measured at the processor core silicon.
2. BCLK period is 10 ns.
58
Mobile Intel Pentium 4 Processor-M Datasheet
System Bus Signal Quality Specifications
Table 33. Asynchronous GTL+, PWRGOOD Input, and TAP Signal Groups Overshoot/
Undershoot Tolerance
Absolute
Maximum
Overshoot
(V)
Absolute
Maximum
Undershoot
(V)
Pulse
Duration (ns)
AF = 1
Pulse
Duration (ns)
AF = 0.1
Pulse
Duration (ns)
AF = 0.01
1.700
-0.400
1.26
12.6
60.00
1.650
-0.350
2.88
28.8
60.00
1.600
-0.300
6.30
60.00
60.00
1.550
-0.250
14.28
60.00
60.00
1.500
-0.200
60.00
60.00
60.00
1.450
-0.150
60.00
60.00
60.00
1.400
-0.100
60.00
60.00
60.00
1.350
-0.050
60.00
60.00
60.00
Notes 1,2
NOTES:
1. These specifications are measured at the processor core silicon.
2. BCLK period is 10 ns.
Figure 30. Maximum Acceptable Overshoot/Undershoot Waveform
Maximum
Absolute
Overshoot
Time-dependent
Overshoot
VMAX
VCC
GTLREF
VOL
VSS
VMIN
Maximum
Absolute
Undershoot
Mobile Intel Pentium 4 Processor-M Datasheet
Time-dependent
Undershoot
59
System Bus Signal Quality Specifications
This page intentionally left blank.
60
Mobile Intel Pentium 4 Processor-M Datasheet
Package Mechanical Specifications
4.
Package Mechanical Specifications
The Mobile Intel Pentium 4 Processor-M is packaged in a 478 pin Micro-FCPGA package.
Different views of the package are shown in Figure 31 through Figure 33. Package dimensions are
shown in Table 34.
Figure 31. Micro-FCPGA Package Top and Bottom Isometric Views
PACKAGE KEEPOUT
CAPACITOR AREA
DIE
LABEL
TOP VIEW
Mobile Intel Pentium 4 Processor-M Datasheet
BOTTOM VIEW
61
Package Mechanical Specifications
Figure 32. Micro-FCPGA Package Top and Side View
SUBSTRATE KEEPOUT ZONE
DO NOT CONTACT PACKAGE
INSIDE THIS LINE
7 (K1)
8 places
5 (K)
4 places
0.286
A
1.25 MAX
(A3)
D1
35 (D)
Ø 0.32 (B)
478 places
A2
E1
35 (E)
PIN A1 CORNER
2.03 ± 0.08
(A1)
All dimensions in millimeters. Values shown are for reference only.
62
Mobile Intel Pentium 4 Processor-M Datasheet
Package Mechanical Specifications
Table 34. Micro-FCPGA Package Dimensions
Symbol Param eter
Min
M ax
Unit
A
Overall height, top of die to package seating plane
1.81
2.03
mm
-
Overall height, top of die to PCB surface, including socket(1)
4.69
5.15
mm
A1
Pin length
1.95
2.11
mm
A2
Die height
A3
Pin-side capacitor height
0.854
-
mm
1.25
mm
B
Pin diameter
0.28
0.36
mm
D
Package substrate length
34.9
35.1
mm
E
Package substrate width
34.9
35.1
mm
Die length
12.24 (B0 Step)
11.62 (B0 Step Shrink
& C1/D1 Step)
mm
E1
Die width
11.93 (B0 Step)
11.34 (B0 Step Shrink
& C1/D1 Step)
mm
e
Pin pitch
1.27
mm
D1
K
Package edge keep-out
5
mm
K1
Package corner keep-out
7
mm
K3
Pin-side capacitor boundary
14
mm
-
Pin tip radial true position
<=0.254
mm
N
Pin count
478
each
Pdie
Allowable pressure on the die for therm al solution
W
Package weight
Package Surface Flatness
-
689
kPa
4.5
g
0.286
mm
NOTES:
1. All Dimensions are subject to change. Values shown are for reference only.
2. Overall height with socket is based on design dimensions of the Micro-FCPGA package and socket with no
thermal solution attached. Values were based on design specifications and tolerances. This dimension is
subject to change based on socket design, OEM motherboard design, or OEM SMT process.
Mobile Intel Pentium 4 Processor-M Datasheet
63
Package Mechanical Specifications
Figure 33. Micro-FCPGA Package - Bottom View
14 (K3)
AF
AD
AB
Y
V
T
P
M
K
H
F
D
B
AE
AC
AA
W
U
R
14 (K3)
N
L
J
G
E
C
A
1
25X 1.27
(e)
3
2
5
4
7
6
9
8
10
11 13 15 17 19 21 23 25
12 14 16 18 20 22 24 26
25X 1.27
(e)
NOTE: All dimensions in millimeters. Values shown are for reference only.
4.1
Processor Pin-Out
Figure 34 shows the top view pinout of the Mobile Intel Pentium 4 Processor-M.
64
Mobile Intel Pentium 4 Processor-M Datasheet
Package Mechanical Specifications
Figure 34.
The Coordinates of the Processor Pins as Viewed From the Top of the Package.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
NC
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
NC
D#[2]
VSS
D#[3]
VSS
FERR#/
PBE#
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
D#[0]
D#[1]
VSS
D#[6]
D#[9]
VSS
VSS PROCHOT# THRMDC VSS A20M#
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
D#[4]
VSS
D#[7]
D#[8]
VSS
D#[12]
BPRI#
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VSS
D#[5]
D#[13]
VSS
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
DBI#[0]
VSS GTLREF TMS
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC GTLREF
A
THERMTRIP# VSS
B
IGNNE#
THRMD
A
VSSSE VCCSE
NSE
NSE
VSS
SMI#
A
GHI#
B
C
C
TDI
D
D
LINT0
VSS
TCK
TDO
VSS
E
VSS DEFER# HITM#
VSS
LINT1 TRST#
D#[15] D#[23]
E
DSTBN#
VSS
[0]
D#[17] D#[21]
VSS
F
RS#[0]
VSS
HIT#
RS#[2]
ADS#
BNR#
VSS
LOCK# RS#[1]
F
DSTBP#
VSS
[0]
D#[19] D#[20]
VSS
D#[22]
G
G
VSS
VSS
D#[10] D#[18]
VSS
DBI#[1] D#[25]
H
H
VSS
DRDY# REQ#[4] VSS
DBSY# BR0#
D#[11] D#[16]
VSS
D#[26] D#[31]
VSS
J
REQ#[0] VSS REQ#[3]REQ#[2] VSS
TRDY#
D#[14]
VSS
DSTBP#
D#[29]
[1]
J
VSS
DP#[0]
K
A#[6]
A#[3]
VSS
A#[4] REQ#[1] VSS
VSS
A#[9]
A#[7]
VSS ADSTB#[0] A#[5]
A#[13]
VSS
A#[10] A#[11]
VSS
K
DSTBN#
D#[30]
[1]
VSS
DP#[1] DP#[2]
L
L
D#[24] D#[28] VSS COMP[0] DP#[3]
VSS
M
M
VSS
A#[8]
D#[27]
VSS
D#[32] D#[35]
VSS
D#[37]
N
N
A#[12] A#[14]
VSS
A#[15] A#[16]
TOP VIEW
VSS
P
COMP[1]
VSS
A#[19] A#[20]
VSS
VSS
A#[24]
D#[34]
R
VSS
A#[18] A#[21]
D#[33] D#[36]
VSS
DSTBP#
D#[41]
[2]
D#[40] DSTBN#
[2]
VSS ADSTB#[1] A#[28]
VSS
D#[39] D#[38]
P
VSS
DBI#[2]
R
VSS
D#[43] D#[42]
VSS
T
T
A#[17] A#[22]
VSS
A#[26] A#[30]
VSS
VSS
D#[46] D#[47]
VSS
D#[45] D#[44]
U
A#[23]
VSS
A#[25] A#[31]
VSS
U
TESTHI
8
D#[52]
VSS
D#[50] D#[49]
VSS
D#[48]
V
V
VSS
A#[27] A#[32]
VSS
AP#[1] MCERR#
DBI#[3] D#[53]
VSS
D#[54] D#[51]
VSS
W
A#[29] A#[33]
VSS
TESTHI
INIT#
9
VSS DSTBN#[3] DSTBP# VSS
[3]
VSS
W
D#[57] D#[55]
Y
A#[34]
VSS
TESTHI
VSS
10 STPCLK#
Y
BPM#[3]
D#[60]
AA
VSS TESTHI1 BINIT#
VSS BPM#[4] GTLREF VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
D#[58] D#[59]
VSS
D#[56]
AA
ITPCLKOUT
GTLREF D#[62] VSS
[0]
D#[63] D#[61]
VSS
AB
A#[35]
RSP#
VSS BPM#[5] BPM#[1] VSS
VCC
VSS
VSS
ITPCLKOU
PWRGOODVSS RESET# SLP#
T[1]
AC
AB
AC
AP#[0]
VSS
IERR# BPM#[2] VSS
BPM#[0] VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS TESTHI3 TESTHI2 VSS TESTHI5 TESTHI4 VSS
ITP_CLK0
AD
VSS
NC
NC
VSS
VID4
VID3
VID2
VID1
VSS
VCC
NC
1
2
3
BSEL1 BSEL0
TESTHI
ITP_CL
DPSLP#
0
K1
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VCCA
VSS
VSSA
VSS
NC
VSS
VCCIO_
PLL
VSS
DBR#
VSS
VCC BCLK[0] BCLK[1]
NC
NC
SKTOC
C#
24
25
26
AE
VID0
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VCCVID VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
AE
AF
VSS
4
VCC
5
21
22
23
AD
AF
Other
Mobile Intel Pentium 4 Processor-M Datasheet
65
Package Mechanical Specifications
This page intentionally left blank.
66
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
5.
Pin Listing and Signal Definitions
5.1
Mobile Intel Pentium 4 Processor-M Pin Assignments
Section 5.1 contains the pin list for the Mobile Intel Pentium 4 Processor-M in Table 35 and Table
36. Table 35 is a listing of all processor pins ordered alphabetically by pin name. Table 36 is also a
listing of all processor pins but ordered by pin number.
Mobile Intel Pentium 4 Processor-M
67
Pin Listing and Signal Definitions
Table 35.
Table 35.
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Pin Name
Direction
A#[03]
K2
Source Synch
Input/Output
A#[04]
K4
Source Synch
Input/Output
A#[05]
L6
Source Synch
Input/Output
A#[06]
K1
Source Synch
Input/Output
A#[07]
L3
Source Synch
Input/Output
A#[08]
M6
Source Synch
Input/Output
A#[09]
L2
Source Synch
Input/Output
A#[10]
M3
Source Synch
Input/Output
A#[11]
M4
Source Synch
Input/Output
A#[12]
N1
Source Synch
Input/Output
A#[13]
M1
Source Synch
Input/Output
A#[14]
N2
Source Synch
Input/Output
A#[15]
N4
Source Synch
Input/Output
A#[16]
N5
Source Synch
Input/Output
A#[17]
T1
Source Synch
Input/Output
A#[18]
R2
Source Synch
Input/Output
A#[19]
P3
Source Synch
Input/Output
A#[20]
P4
Source Synch
Input/Output
A#[21]
R3
Source Synch
Input/Output
A#[22]
T2
Source Synch
Input/Output
A#[23]
U1
Source Synch
Input/Output
A#[24]
P6
Source Synch
Input/Output
A#[25]
U3
Source Synch
Input/Output
A#[26]
T4
Source Synch
Input/Output
A#[27]
V2
Source Synch
Input/Output
A#[28]
R6
Source Synch
Input/Output
A#[29]
W1
Source Synch
Input/Output
A#[30]
T5
Source Synch
Input/Output
A#[31]
U4
Source Synch
Input/Output
A#[32]
V3
Source Synch
Input/Output
A#[33]
W2
Source Synch
Input/Output
A#[34]
Y1
Source Synch
Input/Output
A#[35]
AB1
Source Synch
Input/Output
A20M#
C6
Asynch GTL+
Input
ADS#
G1
Common Clock
Input/Output
ADSTB#[0]
L5
Source Synch
Input/Output
ADSTB#[1]
R5
Source Synch
Input/Output
68
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Direction
AP#[0]
AC1
Common Clock
Input/Output
AP#[1]
V5
Common Clock
Input/Output
BCLK[0]
AF22
Bus Clock
Input
BCLK[1]
AF23
Bus Clock
Input
BINIT#
AA3
Common Clock
Input/Output
BNR#
G2
Common Clock
Input/Output
BPM#[0]
AC6
Common Clock
Input/Output
BPM#[1]
AB5
Common Clock
Input/Output
BPM#[2]
AC4
Common Clock
Input/Output
BPM#[3]
Y6
Common Clock
Input/Output
BPM#[4]
AA5
Common Clock
Input/Output
BPM#[5]
AB4
Common Clock
Input/Output
BPRI#
D2
Common Clock
Input
BR0#
H6
Common Clock
Input/Output
BSEL0
AD6
Power/Other
Output
BSEL1
AD5
Power/Other
Output
COMP[0]
L24
Power/Other
Input/Output
COMP[1]
P1
Power/Other
Input/Output
D#[0]
B21
Source Synch
Input/Output
D#[01]
B22
Source Synch
Input/Output
D#[02]
A23
Source Synch
Input/Output
D#[03]
A25
Source Synch
Input/Output
D#[04]
C21
Source Synch
Input/Output
D#[05]
D22
Source Synch
Input/Output
D#[06]
B24
Source Synch
Input/Output
D#[07]
C23
Source Synch
Input/Output
D#[08]
C24
Source Synch
Input/Output
D#[09]
B25
Source Synch
Input/Output
D#[10]
G22
Source Synch
Input/Output
D#[11]
H21
Source Synch
Input/Output
D#[12]
C26
Source Synch
Input/Output
D#[13]
D23
Source Synch
Input/Output
D#[14]
J21
Source Synch
Input/Output
D#[15]
D25
Source Synch
Input/Output
D#[16]
H22
Source Synch
Input/Output
D#[17]
E24
Source Synch
Input/Output
D#[18]
G23
Source Synch
Input/Output
D#[19]
F23
Source Synch
Input/Output
D#[20]
F24
Source Synch
Input/Output
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 35.
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Table 35.
Direction
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Direction
D#[21]
E25
Source Synch
Input/Output
D#[60]
Y21
Source Synch
Input/Output
D#[22]
F26
Source Synch
Input/Output
D#[61]
AA25
Source Synch
Input/Output
D#[23]
D26
Source Synch
Input/Output
D#[62]
AA22
Source Synch
Input/Output
D#[24]
L21
Source Synch
Input/Output
D#[63]
AA24
Source Synch
Input/Output
D#[25]
G26
Source Synch
Input/Output
DBI#[0]
E21
Source Synch
Input/Output
D#[26]
H24
Source Synch
Input/Output
DBI#[1]
G25
Source Synch
Input/Output
D#[27]
M21
Source Synch
Input/Output
DBI#[2]
P26
Source Synch
Input/Output
D#[28]
L22
Source Synch
Input/Output
DBI#[3]
V21
Source Synch
Input/Output
D#[29]
J24
Source Synch
Input/Output
DBR#
AE25
Power/Other
Output
D#[30]
K23
Source Synch
Input/Output
DBSY#
H5
Common Clock
Input/Output
D#[31]
H25
Source Synch
Input/Output
DEFER#
E2
Common Clock
Input
D#[32]
M23
Source Synch
Input/Output
DP#[0]
J26
Common Clock
Input/Output
D#[33]
N22
Source Synch
Input/Output
DP#[1]
K25
Common Clock
Input/Output
D#[34]
P21
Source Synch
Input/Output
DP#[2]
K26
Common Clock
Input/Output
D#[35]
M24
Source Synch
Input/Output
DP#[3]
L25
Common Clock
Input/Output
D#[36]
N23
Source Synch
Input/Output
DPSLP#
AD25
Asynch GTL+
Input
D#[37]
M26
Source Synch
Input/Output
DRDY#
H2
Common Clock
Input/Output
D#[38]
N26
Source Synch
Input/Output
DSTBN#[0]
E22
Source Synch
Input/Output
D#[39]
N25
Source Synch
Input/Output
DSTBN#[1]
K22
Source Synch
Input/Output
D#[40]
R21
Source Synch
Input/Output
DSTBN#[2]
R22
Source Synch
Input/Output
D#[41]
P24
Source Synch
Input/Output
DSTBN#[3]
W22
Source Synch
Input/Output
D#[42]
R25
Source Synch
Input/Output
DSTBP#[0]
F21
Source Synch
Input/Output
D#[43]
R24
Source Synch
Input/Output
DSTBP#[1]
J23
Source Synch
Input/Output
D#[44]
T26
Source Synch
Input/Output
DSTBP#[2]
P23
Source Synch
Input/Output
D#[45]
T25
Source Synch
Input/Output
DSTBP#[3]
W23
Source Synch
Input/Output
D#[46]
T22
Source Synch
Input/Output
FERR#/PBE#
B6
Asynch AGL+
Output
D#[47]
T23
Source Synch
Input/Output
GHI#
A6
Asynch GTL+
Input
D#[48]
U26
Source Synch
Input/Output
GTLREF
AA21
Power/Other
Input
D#[49]
U24
Source Synch
Input/Output
GTLREF
AA6
Power/Other
Input
D#[50]
U23
Source Synch
Input/Output
GTLREF
F20
Power/Other
Input
D#[51]
V25
Source Synch
Input/Output
GTLREF
F6
Power/Other
Input
D#[52]
U21
Source Synch
Input/Output
HIT#
F3
Common Clock
Input/Output
D#[53]
V22
Source Synch
Input/Output
HITM#
E3
Common Clock
Input/Output
D#[54]
V24
Source Synch
Input/Output
IERR#
AC3
Common Clock
Output
D#[55]
W26
Source Synch
Input/Output
IGNNE#
B2
Asynch GTL+
Input
D#[56]
Y26
Source Synch
Input/Output
INIT#
W5
Asynch GTL+
Input
D#[57]
W25
Source Synch
Input/Output
ITPCLKOUT[0]
AA20
Power/Other
Output
D#[58]
Y23
Source Synch
Input/Output
ITPCLKOUT[1]
AB22
Power/Other
Output
D#[59]
Y24
Source Synch
Input/Output
ITP_CLK0
AC26
TAP
input
Mobile Intel Pentium 4 Processor-M Datasheet
69
Pin Listing and Signal Definitions
Table 35.
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Table 35.
Direction
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Direction
ITP_CLK1
AD26
TAP
input
TESTHI9
W4
Power/Other
Input
LINT0
D1
Asynch GTL+
Input
TESTHI10
Y3
Power/Other
Input
LINT1
E5
Asynch GTL+
Input
THERMDA
B3
Power/Other
LOCK#
G4
Common Clock
Input/Output
THERMDC
C4
Power/Other
MCERR#
V6
Common Clock
Input/Output
THERMTRIP#
A2
Asynch GTL+
Output
NC
A22
TMS
F7
TAP
Input
NC
A7
TRDY#
J6
Common Clock
Input
NC
AD2
TRST#
E6
TAP
Input
NC
AD3
VCC
A10
Power/Other
NC
AE21
VCC
A12
Power/Other
NC
AF3
VCC
A14
Power/Other
NC
AF24
VCC
A16
Power/Other
NC
AF25
VCC
A18
Power/Other
PROCHOT#
C3
Asynch GTL+
Output
VCC
A20
Power/Other
PWRGOOD
AB23
Power/Other
Input
VCC
A8
Power/Other
REQ#[0]
J1
Source Synch
Input/Output
VCC
AA10
Power/Other
REQ#[1]
K5
Source Synch
Input/Output
VCC
AA12
Power/Other
REQ#[2]
J4
Source Synch
Input/Output
VCC
AA14
Power/Other
REQ#[3]
J3
Source Synch
Input/Output
VCC
AA16
Power/Other
REQ#[4]
H3
Source Synch
Input/Output
VCC
AA18
Power/Other
RESET#
AB25
Common Clock
Input
VCC
AA8
Power/Other
RS#[0]
F1
Common Clock
Input
VCC
AB11
Power/Other
RS#[1]
G5
Common Clock
Input
VCC
AB13
Power/Other
RS#[2]
F4
Common Clock
Input
VCC
AB15
Power/Other
RSP#
AB2
Common Clock
Input
VCC
AB17
Power/Other
SKTOCC#
AF26
Power/Other
Output
VCC
AB19
Power/Other
SLP#
AB26
Asynch GTL+
Input
VCC
AB7
Power/Other
SMI#
B5
Asynch GTL+
Input
VCC
AB9
Power/Other
STPCLK#
Y4
Asynch GTL+
Input
VCC
AC10
Power/Other
TCK
D4
TAP
Input
VCC
AC12
Power/Other
TDI
C1
TAP
Input
VCC
AC14
Power/Other
TDO
D5
TAP
Output
VCC
AC16
Power/Other
TESTHI0
AD24
Power/Other
Input
VCC
AC18
Power/Other
TESTHI1
AA2
Power/Other
Input
VCC
AC8
Power/Other
TESTHI2
AC21
Power/Other
Input
VCC
AD11
Power/Other
TESTHI3
AC20
Power/Other
Input
VCC
AD13
Power/Other
TESTHI4
AC24
Power/Other
Input
VCC
AD15
Power/Other
TESTHI5
AC23
Power/Other
Input
VCC
AD17
Power/Other
TESTHI8
U6
Power/Other
Input
VCC
AD19
Power/Other
70
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 35.
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Table 35.
Direction
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Direction
VCC
AD7
Power/Other
VCC
D7
Power/Other
VCC
AD9
Power/Other
VCC
D9
Power/Other
VCC
AE10
Power/Other
VCC
E10
Power/Other
VCC
AE12
Power/Other
VCC
E12
Power/Other
VCC
AE14
Power/Other
VCC
E14
Power/Other
VCC
AE16
Power/Other
VCC
E16
Power/Other
VCC
AE18
Power/Other
VCC
E18
Power/Other
VCC
AE20
Power/Other
VCC
E20
Power/Other
VCC
AE6
Power/Other
VCC
E8
Power/Other
VCC
AE8
Power/Other
VCC
F11
Power/Other
VCC
AF11
Power/Other
VCC
F13
Power/Other
VCC
AF13
Power/Other
VCC
F15
Power/Other
VCC
AF15
Power/Other
VCC
F17
Power/Other
VCC
AF17
Power/Other
VCC
F19
Power/Other
VCC
AF19
Power/Other
VCC
F9
Power/Other
VCC
AF2
Power/Other
VCCA
AD20
Power/Other
VCC
AF21
Power/Other
VCCIOPLL
AE23
Power/Other
VCC
AF5
Power/Other
VCCSENSE
A5
Power/Other
Output
VCC
AF7
Power/Other
VCCVID
AF4
Power/Other
Input
VCC
AF9
Power/Other
VID0
AE5
Power/Other
Output
VCC
B11
Power/Other
VID1
AE4
Power/Other
Output
VCC
B13
Power/Other
VID2
AE3
Power/Other
Output
VCC
B15
Power/Other
VID3
AE2
Power/Other
Output
VCC
B17
Power/Other
VID4
AE1
Power/Other
Output
VCC
B19
Power/Other
VSS
A11
Power/Other
VCC
B7
Power/Other
VSS
A13
Power/Other
VCC
B9
Power/Other
VSS
A15
Power/Other
VCC
C10
Power/Other
VSS
A17
Power/Other
VCC
C12
Power/Other
VSS
A19
Power/Other
VCC
C14
Power/Other
VSS
A21
Power/Other
VCC
C16
Power/Other
VSS
A24
Power/Other
VCC
C18
Power/Other
VSS
A26
Power/Other
VCC
C20
Power/Other
VSS
A3
Power/Other
VCC
C8
Power/Other
VSS
A9
Power/Other
VCC
D11
Power/Other
VSS
AA1
Power/Other
VCC
D13
Power/Other
VSS
AA11
Power/Other
VCC
D15
Power/Other
VSS
AA13
Power/Other
VCC
D17
Power/Other
VSS
AA15
Power/Other
VCC
D19
Power/Other
VSS
AA17
Power/Other
Mobile Intel Pentium 4 Processor-M Datasheet
71
Pin Listing and Signal Definitions
Table 35.
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Table 35.
Direction
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
VSS
AA19
Power/Other
VSS
AE13
Power/Other
VSS
AA23
Power/Other
VSS
AE15
Power/Other
VSS
AA26
Power/Other
VSS
AE17
Power/Other
VSS
AA4
Power/Other
VSS
AE19
Power/Other
VSS
AA7
Power/Other
VSS
AE22
Power/Other
VSS
AA9
Power/Other
VSS
AE24
Power/Other
VSS
AB10
Power/Other
VSS
AE26
Power/Other
VSS
AB12
Power/Other
VSS
AE7
Power/Other
VSS
AB14
Power/Other
VSS
AE9
Power/Other
VSS
AB16
Power/Other
VSS
AF1
Power/Other
VSS
AB18
Power/Other
VSS
AF10
Power/Other
VSS
AB20
Power/Other
VSS
AF12
Power/Other
VSS
AB21
Power/Other
VSS
AF14
Power/Other
VSS
AB24
Power/Other
VSS
AF16
Power/Other
VSS
AB3
Power/Other
VSS
AF18
Power/Other
VSS
AB6
Power/Other
VSS
AF20
Power/Other
VSS
AB8
Power/Other
VSS
AF6
Power/Other
VSS
AC11
Power/Other
VSS
AF8
Power/Other
VSS
AC13
Power/Other
VSS
B10
Power/Other
VSS
AC15
Power/Other
VSS
B12
Power/Other
VSS
AC17
Power/Other
VSS
B14
Power/Other
VSS
AC19
Power/Other
VSS
B16
Power/Other
VSS
AC2
Power/Other
VSS
B18
Power/Other
VSS
AC22
Power/Other
VSS
B20
Power/Other
VSS
AC25
Power/Other
VSS
B23
Power/Other
VSS
AC5
Power/Other
VSS
B26
Power/Other
VSS
AC7
Power/Other
VSS
B4
Power/Other
VSS
AC9
Power/Other
VSS
B8
Power/Other
VSS
AD1
Power/Other
VSS
C11
Power/Other
VSS
AD10
Power/Other
VSS
C13
Power/Other
VSS
AD12
Power/Other
VSS
C15
Power/Other
VSS
AD14
Power/Other
VSS
C17
Power/Other
VSS
AD16
Power/Other
VSS
C19
Power/Other
VSS
AD18
Power/Other
VSS
C2
Power/Other
VSS
AD21
Power/Other
VSS
C22
Power/Other
VSS
AD23
Power/Other
VSS
C25
Power/Other
VSS
AD4
Power/Other
VSS
C5
Power/Other
VSS
AD8
Power/Other
VSS
C7
Power/Other
VSS
AE11
Power/Other
VSS
C9
Power/Other
72
Direction
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 35.
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
Table 35.
Direction
Pin Name
Pin Listing by Pin Name
Pin
Number
Signal Buffer
Type
VSS
D10
Power/Other
VSS
H4
Power/Other
VSS
D12
Power/Other
VSS
J2
Power/Other
VSS
D14
Power/Other
VSS
J22
Power/Other
VSS
D16
Power/Other
VSS
J25
Power/Other
VSS
D18
Power/Other
VSS
J5
Power/Other
VSS
D20
Power/Other
VSS
K21
Power/Other
VSS
D21
Power/Other
VSS
K24
Power/Other
VSS
D24
Power/Other
VSS
K3
Power/Other
VSS
D3
Power/Other
VSS
K6
Power/Other
VSS
D6
Power/Other
VSS
L1
Power/Other
VSS
D8
Power/Other
VSS
L23
Power/Other
VSS
E1
Power/Other
VSS
L26
Power/Other
VSS
E11
Power/Other
VSS
L4
Power/Other
VSS
E13
Power/Other
VSS
M2
Power/Other
VSS
E15
Power/Other
VSS
M22
Power/Other
VSS
E17
Power/Other
VSS
M25
Power/Other
VSS
E19
Power/Other
VSS
M5
Power/Other
VSS
E23
Power/Other
VSS
N21
Power/Other
VSS
E26
Power/Other
VSS
N24
Power/Other
VSS
E4
Power/Other
VSS
N3
Power/Other
VSS
E7
Power/Other
VSS
N6
Power/Other
VSS
E9
Power/Other
VSS
P2
Power/Other
VSS
F10
Power/Other
VSS
P22
Power/Other
VSS
F12
Power/Other
VSS
P25
Power/Other
VSS
F14
Power/Other
VSS
P5
Power/Other
VSS
F16
Power/Other
VSS
R1
Power/Other
VSS
F18
Power/Other
VSS
R23
Power/Other
VSS
F2
Power/Other
VSS
R26
Power/Other
VSS
F22
Power/Other
VSS
R4
Power/Other
VSS
F25
Power/Other
VSS
T21
Power/Other
VSS
F5
Power/Other
VSS
T24
Power/Other
VSS
F8
Power/Other
VSS
T3
Power/Other
VSS
G21
Power/Other
VSS
T6
Power/Other
VSS
G24
Power/Other
VSS
U2
Power/Other
VSS
G3
Power/Other
VSS
U22
Power/Other
VSS
G6
Power/Other
VSS
U25
Power/Other
VSS
H1
Power/Other
VSS
U5
Power/Other
VSS
H23
Power/Other
VSS
V1
Power/Other
VSS
H26
Power/Other
VSS
V23
Power/Other
Mobile Intel Pentium 4 Processor-M Datasheet
Direction
73
Pin Listing and Signal Definitions
Table 35.
Pin Listing by Pin Name
Pin
Number
Pin Name
Signal Buffer
Type
Table 36. Pin Listing by Pin Number
Direction
Pin
Number
Pin Name
Signal Buffer
Type
Direction
VSS
V26
Power/Other
A25
D#[03]
Source Synch
VSS
V4
Power/Other
A26
VSS
Power/Other
VSS
W21
Power/Other
AA1
VSS
Power/Other
VSS
W24
Power/Other
AA2
TESTHI1
Power/Other
Input
VSS
W3
Power/Other
AA3
BINIT#
Common Clock
Input/Output
VSS
W6
Power/Other
AA4
VSS
Power/Other
VSS
Y2
Power/Other
AA5
BPM#[4]
Common Clock
Input/Output
VSS
Y22
Power/Other
AA6
GTLREF
Power/Other
Input
VSS
Y25
Power/Other
AA7
VSS
Power/Other
VSS
Y5
Power/Other
AA8
VCC
Power/Other
VSSA
AD22
Power/Other
AA9
VSS
Power/Other
VSSSENSE
A4
Power/Other
AA10
VCC
Power/Other
AA11
VSS
Power/Other
AA12
VCC
Power/Other
AA13
VSS
Power/Other
AA14
VCC
Power/Other
AA15
VSS
Power/Other
AA16
VCC
Power/Other
AA17
VSS
Power/Other
AA18
VCC
Power/Other
AA19
VSS
Power/Other
AA20
ITPCLKOUT
[0]
Power/Other
Output
Output
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
Output
Input/Output
A2
THERMTRIP#
Asynch GTL+
A3
VSS
Power/Other
A4
VSSSENSE
Power/Other
Output
A5
VCCSENSE
Power/Other
Output
A6
GHI#
Asynch GTL+
Input
A7
NC
A8
VCC
Power/Other
A9
VSS
Power/Other
AA21
GTLREF
Power/Other
Input
A10
VCC
Power/Other
AA22
D#[62]
Source Synch
Input/Output
A11
VSS
Power/Other
AA23
VSS
Power/Other
D#[63]
Source Synch
Input/Output
Input/Output
A12
VCC
Power/Other
AA24
A13
VSS
Power/Other
AA25
D#[61]
Source Synch
A14
VCC
Power/Other
AA26
VSS
Power/Other
A15
VSS
Power/Other
AB1
A#[35]
Source Synch
Input/Output
RSP#
Common Clock
Input
A16
VCC
Power/Other
AB2
A17
VSS
Power/Other
AB3
VSS
Power/Other
A18
VCC
Power/Other
AB4
BPM#[5]
Common Clock
Input/Output
A19
VSS
Power/Other
AB5
BPM#[1]
Common Clock
Input/Output
VSS
Power/Other
A20
VCC
Power/Other
AB6
A21
VSS
Power/Other
AB7
VCC
Power/Other
A22
NC
AB8
VSS
Power/Other
A23
D#[02]
AB9
VCC
Power/Other
AB10
VSS
Power/Other
A24
74
VSS
Source Synch
Power/Other
Input/Output
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
AB11
VCC
Power/Other
AC23
TESTHI5
Power/Other
Input
AB12
VSS
Power/Other
AC24
TESTHI4
Power/Other
Input
AB13
VCC
Power/Other
AC25
VSS
Power/Other
AB14
VSS
Power/Other
AC26
ITP_CLK0
TAP
AB15
VCC
Power/Other
AD1
VSS
Power/Other
AB16
VSS
Power/Other
AD2
NC
AB17
VCC
Power/Other
AD3
NC
AB18
VSS
Power/Other
AD4
VSS
Power/Other
AB19
VCC
Power/Other
AD5
BSEL1
Power/Other
Output
AB20
VSS
Power/Other
AD6
BSEL0
Power/Other
Output
AB21
VSS
Power/Other
AD7
VCC
Power/Other
AB22
ITPCLKOUT
[1]
Power/Other
AD8
VSS
Power/Other
AD9
VCC
Power/Other
AB23
PWRGOOD
Power/Other
AD10
VSS
Power/Other
AB24
VSS
Power/Other
AD11
VCC
Power/Other
AB25
RESET#
Common Clock
Input
AD12
VSS
Power/Other
AB26
SLP#
Asynch GTL+
Input
AD13
VCC
Power/Other
AC1
AP#[0]
Common Clock
Input/Output
AD14
VSS
Power/Other
AC2
VSS
Power/Other
AD15
VCC
Power/Other
AC3
IERR#
Common Clock
Output
AD16
VSS
Power/Other
AC4
BPM#[2]
Common Clock
Input/Output
AD17
VCC
Power/Other
AC5
VSS
Power/Other
AD18
VSS
Power/Other
AC6
BPM#[0]
Common Clock
AD19
VCC
Power/Other
AC7
VSS
Power/Other
AD20
VCCA
Power/Other
AC8
VCC
Power/Other
AD21
VSS
Power/Other
AC9
VSS
Power/Other
AD22
VSSA
Power/Other
AC10
VCC
Power/Other
AD23
VSS
Power/Other
AC11
VSS
Power/Other
AD24
TESTHI0
Power/Other
Input
AC12
VCC
Power/Other
AD25
DPSLP#
Asynch GTL+
Input
AC13
VSS
Power/Other
AD26
ITP_CLK1
TAP
input
AC14
VCC
Power/Other
AE1
VID4
Power/Other
Output
AC15
VSS
Power/Other
AE2
VID3
Power/Other
Output
AC16
VCC
Power/Other
AE3
VID2
Power/Other
Output
AC17
VSS
Power/Other
AE4
VID1
Power/Other
Output
AC18
VCC
Power/Other
AE5
VID0
Power/Other
Output
AC19
VSS
Power/Other
AE6
VCC
Power/Other
AC20
TESTHI3
Power/Other
Input
AE7
VSS
Power/Other
AC21
TESTHI2
Power/Other
Input
AE8
VCC
Power/Other
AC22
VSS
Power/Other
AE9
VSS
Power/Other
Output
Input
Input/Output
Mobile Intel Pentium 4 Processor-M Datasheet
input
75
Pin Listing and Signal Definitions
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
AE10
VCC
Power/Other
AF23
BCLK[1]
AE11
VSS
Power/Other
AF24
NC
AE12
VCC
Power/Other
AF25
NC
AE13
VSS
Power/Other
AF26
AE14
VCC
Power/Other
B2
AE15
VSS
Power/Other
AE16
VCC
AE17
AE18
Signal Buffer
Type
Direction
Bus Clock
Input
SKTOCC#
Power/Other
Output
IGNNE#
Asynch GTL+
Input
B3
THERMDA
Power/Other
Power/Other
B4
VSS
Power/Other
VSS
Power/Other
B5
SMI#
Asynch GTL+
Input
VCC
Power/Other
B6
FERR#/PBE#
Asynch AGL+
Output
AE19
VSS
Power/Other
B7
VCC
Power/Other
AE20
VCC
Power/Other
B8
VSS
Power/Other
AE21
NC
B9
VCC
Power/Other
AE22
VSS
Power/Other
B10
VSS
Power/Other
AE23
VCCIOPLL
Power/Other
B11
VCC
Power/Other
AE24
VSS
Power/Other
B12
VSS
Power/Other
AE25
DBR#
Asynch GTL+
B13
VCC
Power/Other
AE26
VSS
Power/Other
B14
VSS
Power/Other
AF1
VSS
Power/Other
B15
VCC
Power/Other
AF2
VCC
Power/Other
B16
VSS
Power/Other
AF3
NC
B17
VCC
Power/Other
AF4
VCCVID
Power/Other
B18
VSS
Power/Other
AF5
VCC
Power/Other
B19
VCC
Power/Other
AF6
VSS
Power/Other
B20
VSS
Power/Other
AF7
VCC
Power/Other
B21
D#[0]
Source Synch
Input/Output
AF8
VSS
Power/Other
B22
D#[01]
Source Synch
Input/Output
AF9
VCC
Power/Other
B23
VSS
Power/Other
AF10
VSS
Power/Other
B24
D#[06]
Source Synch
Input/Output
AF11
VCC
Power/Other
B25
D#[09]
Source Synch
Input/Output
AF12
VSS
Power/Other
B26
VSS
Power/Other
AF13
VCC
Power/Other
C1
TDI
TAP
AF14
VSS
Power/Other
C2
VSS
Power/Other
AF15
VCC
Power/Other
C3
PROCHOT#
Asynch GTL+
AF16
VSS
Power/Other
C4
THERMDC
Power/Other
AF17
VCC
Power/Other
C5
VSS
Power/Other
AF18
VSS
Power/Other
C6
A20M#
Asynch GTL+
AF19
VCC
Power/Other
C7
VSS
Power/Other
AF20
VSS
Power/Other
C8
VCC
Power/Other
AF21
VCC
Power/Other
C9
VSS
Power/Other
AF22
BCLK[0]
Bus Clock
C10
VCC
Power/Other
76
Output
Input
Input
Input
Output
Input
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
C11
VSS
Power/Other
D24
VSS
Power/Other
C12
VCC
Power/Other
D25
D#[15]
Source Synch
Input/Output
C13
VSS
Power/Other
D26
D#[23]
Source Synch
Input/Output
C14
VCC
Power/Other
E1
VSS
Power/Other
C15
VSS
Power/Other
E2
DEFER#
Common Clock
Input
C16
VCC
Power/Other
E3
HITM#
Common Clock
Input/Output
C17
VSS
Power/Other
E4
VSS
Power/Other
C18
VCC
Power/Other
E5
LINT1
Asynch GTL+
Input
C19
VSS
Power/Other
E6
TRST#
TAP
Input
C20
VCC
Power/Other
E7
VSS
Power/Other
C21
D#[04]
Source Synch
E8
VCC
Power/Other
C22
VSS
Power/Other
E9
VSS
Power/Other
C23
D#[07]
Source Synch
Input/Output
E10
VCC
Power/Other
C24
D#[08]
Source Synch
Input/Output
E11
VSS
Power/Other
C25
VSS
Power/Other
E12
VCC
Power/Other
C26
D#[12]
Source Synch
Input/Output
E13
VSS
Power/Other
D1
LINT0
Asynch GTL+
Input
E14
VCC
Power/Other
D2
BPRI#
Common Clock
Input
E15
VSS
Power/Other
D3
VSS
Power/Other
E16
VCC
Power/Other
D4
TCK
TAP
Input
E17
VSS
Power/Other
D5
TDO
TAP
Output
E18
VCC
Power/Other
D6
VSS
Power/Other
E19
VSS
Power/Other
D7
VCC
Power/Other
E20
VCC
Power/Other
D8
VSS
Power/Other
E21
DBI#[0]
Source Synch
Input/Output
D9
VCC
Power/Other
E22
DSTBN#[0]
Source Synch
Input/Output
D10
VSS
Power/Other
E23
VSS
Power/Other
D11
VCC
Power/Other
E24
D#[17]
Source Synch
Input/Output
D12
VSS
Power/Other
E25
D#[21]
Source Synch
Input/Output
D13
VCC
Power/Other
E26
VSS
Power/Other
D14
VSS
Power/Other
F1
RS#[0]
Common Clock
D15
VCC
Power/Other
F2
VSS
Power/Other
D16
VSS
Power/Other
F3
HIT#
Common Clock
Input/Output
D17
VCC
Power/Other
F4
RS#[2]
Common Clock
Input
D18
VSS
Power/Other
F5
VSS
Power/Other
D19
VCC
Power/Other
F6
GTLREF
Power/Other
Input
D20
VSS
Power/Other
F7
TMS
TAP
Input
D21
VSS
Power/Other
F8
VSS
Power/Other
D22
D#[05]
Source Synch
Input/Output
F9
VCC
Power/Other
D23
D#[13]
Source Synch
Input/Output
F10
VSS
Power/Other
Input/Output
Mobile Intel Pentium 4 Processor-M Datasheet
Input
77
Pin Listing and Signal Definitions
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
F11
VCC
Power/Other
H26
VSS
Power/Other
F12
VSS
Power/Other
J1
REQ#[0]
Source Synch
F13
VCC
Power/Other
J2
VSS
Power/Other
F14
VSS
Power/Other
J3
REQ#[3]
Source Synch
Input/Output
F15
VCC
Power/Other
J4
REQ#[2]
Source Synch
Input/Output
F16
VSS
Power/Other
J5
VSS
Power/Other
F17
VCC
Power/Other
J6
TRDY#
Common Clock
Input
F18
VSS
Power/Other
J21
D#[14]
Source Synch
Input/Output
F19
VCC
Power/Other
J22
VSS
Power/Other
F20
GTLREF
Power/Other
Input
J23
DSTBP#[1]
Source Synch
Input/Output
F21
DSTBP#[0]
Source Synch
Input/Output
J24
D#[29]
Source Synch
Input/Output
F22
VSS
Power/Other
J25
VSS
Power/Other
F23
D#[19]
Source Synch
Input/Output
J26
DP#[0]
Common Clock
Input/Output
F24
D#[20]
Source Synch
Input/Output
K1
A#[06]
Source Synch
Input/Output
F25
VSS
Power/Other
K2
A#[03]
Source Synch
Input/Output
F26
D#[22]
Source Synch
Input/Output
K3
VSS
Power/Other
G1
ADS#
Common Clock
Input/Output
K4
A#[04]
Source Synch
Input/Output
G2
BNR#
Common Clock
Input/Output
K5
REQ#[1]
Source Synch
Input/Output
G3
VSS
Power/Other
K6
VSS
Power/Other
G4
LOCK#
Common Clock
Input/Output
K21
VSS
Power/Other
G5
RS#[1]
Common Clock
Input
K22
DSTBN#[1]
Source Synch
Input/Output
G6
VSS
Power/Other
K23
D#[30]
Source Synch
Input/Output
G21
VSS
Power/Other
K24
VSS
Power/Other
G22
D#[10]
Source Synch
Input/Output
K25
DP#[1]
Common Clock
Input/Output
G23
D#[18]
Source Synch
Input/Output
K26
DP#[2]
Common Clock
Input/Output
G24
VSS
Power/Other
L1
VSS
Power/Other
G25
DBI#[1]
Source Synch
Input/Output
L2
A#[09]
Source Synch
Input/Output
G26
D#[25]
Source Synch
Input/Output
L3
A#[07]
Source Synch
Input/Output
H1
VSS
Power/Other
L4
VSS
Power/Other
H2
DRDY#
Common Clock
Input/Output
L5
ADSTB#[0]
Source Synch
Input/Output
H3
REQ#[4]
Source Synch
Input/Output
L6
A#[05]
Source Synch
Input/Output
H4
VSS
Power/Other
L21
D#[24]
Source Synch
Input/Output
H5
DBSY#
Common Clock
Input/Output
L22
D#[28]
Source Synch
Input/Output
H6
BR0#
Common Clock
Input/Output
L23
VSS
Power/Other
H21
D#[11]
Source Synch
Input/Output
L24
COMP[0]
Power/Other
Input/Output
H22
D#[16]
Source Synch
Input/Output
L25
DP#[3]
Common Clock
Input/Output
H23
VSS
Power/Other
L26
VSS
Power/Other
H24
D#[26]
Source Synch
Input/Output
M1
A#[13]
Source Synch
H25
D#[31]
Source Synch
Input/Output
M2
VSS
Power/Other
78
Input/Output
Input/Output
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
M3
A#[10]
Source Synch
Input/Output
R6
A#[28]
Source Synch
Input/Output
M4
A#[11]
Source Synch
Input/Output
R21
D#[40]
Source Synch
Input/Output
M5
VSS
Power/Other
R22
DSTBN#[2]
Source Synch
Input/Output
M6
A#[08]
Source Synch
Input/Output
R23
VSS
Power/Other
M21
D#[27]
Source Synch
Input/Output
R24
D#[43]
Source Synch
Input/Output
M22
VSS
Power/Other
R25
D#[42]
Source Synch
Input/Output
M23
D#[32]
Source Synch
Input/Output
R26
VSS
Power/Other
M24
D#[35]
Source Synch
Input/Output
T1
A#[17]
Source Synch
Input/Output
M25
VSS
Power/Other
T2
A#[22]
Source Synch
Input/Output
M26
D#[37]
Source Synch
Input/Output
T3
VSS
Power/Other
N1
A#[12]
Source Synch
Input/Output
T4
A#[26]
Source Synch
Input/Output
N2
A#[14]
Source Synch
Input/Output
T5
A#[30]
Source Synch
Input/Output
N3
VSS
Power/Other
T6
VSS
Power/Other
N4
A#[15]
Source Synch
Input/Output
T21
VSS
Power/Other
N5
A#[16]
Source Synch
Input/Output
T22
D#[46]
Source Synch
Input/Output
N6
VSS
Power/Other
T23
D#[47]
Source Synch
Input/Output
N21
VSS
Power/Other
T24
VSS
Power/Other
N22
D#[33]
Source Synch
Input/Output
T25
D#[45]
Source Synch
Input/Output
N23
D#[36]
Source Synch
Input/Output
T26
D#[44]
Source Synch
Input/Output
N24
VSS
Power/Other
U1
A#[23]
Source Synch
Input/Output
N25
D#[39]
Source Synch
Input/Output
U2
VSS
Power/Other
N26
D#[38]
Source Synch
Input/Output
U3
A#[25]
Source Synch
Input/Output
P1
COMP[1]
Power/Other
Input/Output
U4
A#[31]
Source Synch
Input/Output
P2
VSS
Power/Other
U5
VSS
Power/Other
P3
A#[19]
Source Synch
Input/Output
U6
TESTHI8
Power/Other
Input
P4
A#[20]
Source Synch
Input/Output
U21
D#[52]
Source Synch
Input/Output
P5
VSS
Power/Other
U22
VSS
Power/Other
P6
A#[24]
Source Synch
Input/Output
U23
D#[50]
Source Synch
Input/Output
P21
D#[34]
Source Synch
Input/Output
U24
D#[49]
Source Synch
Input/Output
P22
VSS
Power/Other
U25
VSS
Power/Other
P23
DSTBP#[2]
Source Synch
Input/Output
U26
D#[48]
Source Synch
P24
D#[41]
Source Synch
Input/Output
V1
VSS
Power/Other
P25
VSS
Power/Other
V2
A#[27]
Source Synch
Input/Output
P26
DBI#[2]
Source Synch
V3
A#[32]
Source Synch
Input/Output
R1
VSS
Power/Other
V4
VSS
Power/Other
R2
A#[18]
Source Synch
Input/Output
V5
AP#[1]
Common Clock
Input/Output
R3
A#[21]
Source Synch
Input/Output
V6
MCERR#
Common Clock
Input/Output
R4
VSS
Power/Other
V21
DBI#[3]
Source Synch
Input/Output
R5
ADSTB#[1]
Source Synch
V22
D#[53]
Source Synch
Input/Output
Input/Output
Input/Output
Mobile Intel Pentium 4 Processor-M Datasheet
Input/Output
79
Pin Listing and Signal Definitions
Table 36. Pin Listing by Pin Number
Pin
Number
Pin Name
Signal Buffer
Type
Direction
V23
VSS
Power/Other
V24
D#[54]
Source Synch
Input/Output
V25
D#[51]
Source Synch
Input/Output
V26
VSS
Power/Other
W1
A#[29]
Source Synch
Input/Output
W2
A#[33]
Source Synch
Input/Output
W3
VSS
Power/Other
W4
TESTHI9
Power/Other
Input
W5
INIT#
Asynch GTL+
Input
W6
VSS
Power/Other
W21
VSS
Power/Other
W22
DSTBN#[3]
Source Synch
Input/Output
W23
DSTBP#[3]
Source Synch
Input/Output
W24
VSS
Power/Other
W25
D#[57]
Source Synch
Input/Output
W26
D#[55]
Source Synch
Input/Output
Y1
A#[34]
Source Synch
Input/Output
Y2
VSS
Power/Other
Y3
TESTHI10
Power/Other
Input
Y4
STPCLK#
Asynch GTL+
Input
Y5
VSS
Power/Other
Y6
BPM#[3]
Common Clock
Input/Output
Y21
D#[60]
Source Synch
Input/Output
Y22
VSS
Power/Other
Y23
D#[58]
Source Synch
Input/Output
Y24
D#[59]
Source Synch
Input/Output
Y25
VSS
Power/Other
Y26
D#[56]
Source Synch
80
Input/Output
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
5.2
Alphabetical Signals Reference
Table 37. Signal Description (Page 1 of 8)
Name
Type
Description
Input/
Output
A[35:3]# (Address) define a 236-byte physical memory address space. In subphase 1 of the address phase, these pins transmit the address of a transaction. In
sub-phase 2, these pins transmit transaction type information. These signals must
connect the appropriate pins of all agents on the Mobile Intel Pentium 4
Processor-M system bus. A[35:3]# are protected by parity signals AP[1:0]#.
A[35:3]# are source synchronous signals and are latched into the receiving buffers
by ADSTB[1:0]#.
On the active-to-inactive transition of RESET#, the processor samples a subset of
the A[35:3]# pins to determine power-on configuration. See Section 7.1 for more
details.
A20M#
Input
If A20M# (Address-20 Mask) is asserted, the processor masks physical address bit
20 (A20#) before looking up a line in any internal cache and before driving a read/
write transaction on the bus. Asserting A20M# emulates the 8086 processor's
address wrap-around at the 1-Mbyte boundary. Assertion of A20M# is only
supported in real mode.
A20M# is an asynchronous signal. However, to ensure recognition of this signal
following an Input/Output write instruction, it must be valid along with the TRDY#
assertion of the corresponding Input/Output Write bus transaction.
ADS#
Input/
Output
ADS# (Address Strobe) is asserted to indicate the validity of the transaction
address on the A[35:3]# and REQ[4:0]# pins. All bus agents observe the ADS#
activation to begin parity checking, protocol checking, address decode, internal
snoop, or deferred reply ID match operations associated with the new transaction.
A[35:3]#
Address strobes are used to latch A[35:3]# and REQ[4:0]# on their rising and falling
edges. Strobes are associated with signals as shown below.
ADSTB[1:0]#
AP[1:0]#
BCLK[1:0]
Input/
Output
Input/
Output
Input
Signals
Associated Strobe
REQ[4:0]#, A[16:3]#
ADSTB0#
A[35:17]#
ADSTB1#
AP[1:0]# (Address Parity) are driven by the request initiator along with ADS#,
A[35:3]#, and the transaction type on the REQ[4:0]#. A correct parity signal is high if
an even number of covered signals are low and low if an odd number of covered
signals are low. This allows parity to be high when all the covered signals are high.
AP[1:0]# should connect the appropriate pins of all Mobile Intel Pentium 4
Processor-M system bus agents. The following table defines the coverage model of
these signals.
Request Signals
subphase 1
subphase 2
A[35:24]#
AP0#
AP1#
A[23:3]#
AP1#
AP0#
REQ[4:0]#
AP1#
AP0#
The differential pair BCLK (Bus Clock) determines the system bus frequency. All
processor system bus agents must receive these signals to drive their outputs and
latch their inputs.
All external timing parameters are specified with respect to the rising edge of
BCLK0 crossing VCROSS.
Mobile Intel Pentium 4 Processor-M Datasheet
81
Pin Listing and Signal Definitions
Table 37. Signal Description (Page 2 of 8)
Name
Type
Description
BINIT#
Input/
Output
BINIT# (Bus Initialization) may be observed and driven by all processor system bus
agents and if used, must connect the appropriate pins of all such agents. If the
BINIT# driver is enabled during power-on configuration, BINIT# is asserted to
signal any bus condition that prevents reliable future operation.
If BINIT# observation is enabled during power-on configuration, and BINIT# is
sampled asserted, symmetric agents reset their bus LOCK# activity and bus
request arbitration state machines. The bus agents do not reset their IOQ and
transaction tracking state machines upon observation of BINIT# activation. Once
the BINIT# assertion has been observed, the bus agents will re-arbitrate for the
system bus and attempt completion of their bus queue and IOQ entries.
If BINIT# observation is disabled during power-on configuration, a central agent
may handle an assertion of BINIT# as appropriate to the error handling architecture
of the system.
BNR#
Input/
Output
BNR# (Block Next Request) is used to assert a bus stall by any bus agent who is
unable to accept new bus transactions. During a bus stall, the current bus owner
cannot issue any new transactions.
Input/
Output
BPM[5:0]# (Breakpoint Monitor) are breakpoint and performance monitor signals.
They are outputs from the processor which indicate the status of breakpoints and
programmable counters used for monitoring processor performance. BPM[5:0]#
should connect the appropriate pins of all Mobile Intel Pentium 4 Processor-M
system bus agents.
BPM4# provides PRDY# (Probe Ready) functionality for the TAP port. PRDY# is a
processor output used by debug tools to determine processor debug readiness.
BPM5# provides PREQ# (Probe Request) functionality for the TAP port. PREQ# is
used by debug tools to request debug operation of the processor.
Please refer to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/
845MZ Chipset Platform Design Guide.
These signals do not have on-die termination and must be terminated on the
system board.
BPRI#
Input
BPRI# (Bus Priority Request) is used to arbitrate for ownership of the processor
system bus. It must connect the appropriate pins of all processor system bus
agents. Observing BPRI# active (as asserted by the priority agent) causes all other
agents to stop issuing new requests, unless such requests are part of an ongoing
locked operation. The priority agent keeps BPRI# asserted until all of its requests
are completed, then releases the bus by deasserting BPRI#.
BR0#
Input/
Output
BR0# drives the BREQ0# signal in the system and is used by the processor to
request the bus. During power-on configuration this pin is sampled to determine the
agent ID = 0.
This signal does not have on-die termination and must be terminated.
BSEL[1:0]
Output
BSEL[1:0] (Bus Select) are used to select the processor input clock frequency.
Table 5 defines the possible combinations of the signals and the frequency
associated with each combination. The required frequency is determined by the
processor, chipset and clock synthesizer. All agents must operate at the same
frequency. The Mobile Intel Pentium 4 Processor-M operates at a 400 MHz system
bus frequency (100 MHz BCLK[1:0] frequency). For more information about these
pins, including termination recommendations refer to Section 2.9 and the
appropriate platform design guidelines.
COMP[1:0]
Analog
COMP[1:0] must be terminated on the system board using precision resistors.
Refer to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ
Chipset Platform Design Guide for details on implementation.
BPM[5:0]#
82
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 37. Signal Description (Page 3 of 8)
Name
Type
Description
D[63:0]# (Data) are the data signals. These signals provide a 64-bit data path
between the processor system bus agents, and must connect the appropriate pins
on all such agents. The data driver asserts DRDY# to indicate a valid data transfer.
D[63:0]# are quad-pumped signals and will thus be driven four times in a common
clock period. D[63:0]# are latched off the falling edge of both DSTBP[3:0]# and
DSTBN[3:0]#. Each group of 16 data signals correspond to a pair of one DSTBP#
and one DSTBN#. The following table shows the grouping of data signals to data
strobes and DBI#.
Quad-Pumped Signal Groups
D[63:0]#
Input/
Output
Data Group
DSTBN#/
DSTBP#
DBI#
D[15:0]#
0
0
D[31:16]#
1
1
D[47:32]#
2
2
D[63:48]#
3
3
Furthermore, the DBI# pins determine the polarity of the data signals. Each group
of 16 data signals corresponds to one DBI# signal. When the DBI# signal is active,
the corresponding data group is inverted and therefore sampled active high.
DBI[3:0]# (Data Bus Inversion) are source synchronous and indicate the polarity of
the D[63:0]# signals. The DBI[3:0]# signals are activated when the data on the data
bus is inverted. If more than half of the data bits, within a 16-bit group, would have
been asserted electrically low, the bus agent may invert the data bus signals for that
particular sub-phase for that 16-bit group.
DBI[3:0] Assignment To Data Bus
DBI[3:0]#
Input/
Output
Bus Signal
Data Bus Signals
DBI3#
D[63:48]#
DBI2#
D[47:32]#
DBI1#
D[31:16]#
DBI0#
D[15:0]#
DBR#
Output
DBR# (Data Bus Reset) is used only in processor systems where no debug port is
implemented on the system board. DBR# is used by a debug port interposer so that
an in-target probe can drive system reset. If a debug port is implemented in the
system, DBR# is a no connect in the system. DBR# is not a processor signal.
DBSY#
Input/
Output
DBSY# (Data Bus Busy) is asserted by the agent responsible for driving data on the
processor system bus to indicate that the data bus is in use. The data bus is
released after DBSY# is deasserted. This signal must connect the appropriate pins
on all processor system bus agents.
DEFER#
Input
DEFER# is asserted by an agent to indicate that a transaction cannot be
guaranteed in-order completion. Assertion of DEFER# is normally the responsibility
of the addressed memory or Input/Output agent. This signal must connect the
appropriate pins of all processor system bus agents.
DP[3:0]#
Input/
Output
DP[3:0]# (Data parity) provide parity protection for the D[63:0]# signals. They are
driven by the agent responsible for driving D[63:0]#, and must connect the
appropriate pins of all Mobile Intel Pentium 4 Processor-M system bus agents.
Mobile Intel Pentium 4 Processor-M Datasheet
83
Pin Listing and Signal Definitions
Table 37. Signal Description (Page 4 of 8)
Name
Type
Description
DPSLP#
Input
DPSLP# when asserted on the platform causes the processor to transition from the
Sleep State to the Deep Sleep state. In order to return to the Sleep State, DPSLP#
must be deasserted and BCLK[1:0] must be running.
DRDY#
Input/
Output
DRDY# (Data Ready) is asserted by the data driver on each data transfer,
indicating valid data on the data bus. In a multi-common clock data transfer, DRDY#
may be deasserted to insert idle clocks. This signal must connect the appropriate
pins of all processor system bus agents.
Data strobe used to latch in D[63:0]#.
DSTBN[3:0]#
Input/
Output
Signals
Associated Strobe
D[15:0]#, DBI0#
DSTBN0#
D[31:16]#, DBI1#
DSTBN1#
D[47:32]#, DBI2#
DSTBN2#
D[63:48]#, DBI3#
DSTBN3#
Data strobe used to latch in D[63:0]#.
Signals
DSTBP[3:0]#
FERR#/PBE#
GHI#
GTLREF
84
Input/
Output
Associated Strobe
D[15:0]#, DBI0#
DSTBP0#
D[31:16]#, DBI1#
DSTBP1#
D[47:32]#, DBI2#
DSTBP2#
D[63:48]#, DBI3#
DSTBP3#
Output
FERR#/PBE# (floating point error/pending break event) is a multiplexed signal and
its meaning is qualified by STPCLK#. When STPCLK# is not asserted, FERR#/
PBE# indicates a floating-point error and will be asserted when the processor
detects an unmasked floating-point error. When STPCLK# is not asserted, FERR#/
PBE# is similar to the ERROR# signal on the INTEL 387 coprocessor, and is
included for compatibility with systems using MS-DOS*-type floating-point error
reporting. When STPCLK# is asserted, an assertion of FERR#/PBE# indicates that
the processor has a pending break event waiting for service. The assertion of
FERR#/PBE# indicates that the processor should be returned to the Normal state.
When FERR#/PBE# is asserted, indicating a break event, it will remain asserted
until STPCLK# is deasserted. For additional information on the pending break
event functionality, including the identification of support of the feature and enable/
disable information, refer to volume 3 of the Intel Architecture Software Developer's
Manual and the Intel Processor Identification and the CPUID Instruction application
note.
Input
The GHI# signal controls the selection of the operating mode bus ratio and voltage
in the Mobile Intel Pentium 4 Processor-M. On the Mobile Intel Pentium 4
Processor-M featuring Enhanced Intel SpeedStep technology, this signal is latched
on entry to Sleep state and is observed during the Deep Sleep state. GHI#
determines which of two performance states is selected for operation. This signal is
ignored when the processor is not in the Deep Sleep state. This signal should be
driven with an Open-drain driver. Refer to the Mobile Intel Pentium 4
Processor-M and Intel 845MP/845MZ Chipset Platform Design Guide for
termination and connection guidelines.
Input
GTLREF determines the signal reference level for AGTL+ input pins. GTLREF
should be set at 2/3 VCC. GTLREF is used by the AGTL+ receivers to determine if a
signal is a logical 0 or logical 1. Refer to the Mobile Intel Pentium 4 Processor-M
and Intel 845MP/845MZ Chipset Platform Design Guide for more information.
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 37. Signal Description (Page 5 of 8)
Name
HIT#
HITM#
IERR#
IGNNE#
INIT#
ITPCLKOUT
[1:0]
ITP_CLK[1:0]
LINT[1:0]
LOCK#
Type
Input/
Output
Input/
Output
Output
Description
HIT# (Snoop Hit) and HITM# (Hit Modified) convey transaction snoop operation
results. Any system bus agent may assert both HIT# and HITM# together to
indicate that it requires a snoop stall, which can be continued by reasserting HIT#
and HITM# together.
IERR# (Internal Error) is asserted by a processor as the result of an internal error.
Assertion of IERR# is usually accompanied by a SHUTDOWN transaction on the
processor system bus. This transaction may optionally be converted to an external
error signal (e.g., NMI) by system core logic. The processor will keep IERR#
asserted until the assertion of RESET#.
This signal does not have on-die termination and must be terminated on the
system board.
Input
IGNNE# (Ignore Numeric Error) is asserted to force the processor to ignore a
numeric error and continue to execute noncontrol floating-point instructions. If
IGNNE# is deasserted, the processor generates an exception on a noncontrol
floating-point instruction if a previous floating-point instruction caused an error.
IGNNE# has no effect when the NE bit in control register 0 (CR0) is set.
IGNNE# is an asynchronous signal. However, to ensure recognition of this signal
following an Input/Output write instruction, it must be valid along with the TRDY#
assertion of the corresponding Input/Output Write bus transaction.
Input
INIT# (Initialization), when asserted, resets integer registers inside the processor
without affecting its internal caches or floating-point registers. The processor then
begins execution at the power-on Reset vector configured during power-on
configuration. The processor continues to handle snoop requests during INIT#
assertion. INIT# is an asynchronous signal and must connect the appropriate pins
of all processor system bus agents.
If INIT# is sampled active on the active to inactive transition of RESET#, then the
processor executes its Built-in Self-Test (BIST).
Output
ITPCLKOUT[1:0] is an uncompensated differential clock output that is a delayed
copy of the BCLK[1:0], which is an input to the processor. This clock output can be
used as the differential clock into the ITP port that is designed onto the
motherboard. If ITPCLKOUT[1:0] outputs are not used, they must be terminated
properly. Refer to Section 2.5 for additional details and termination requirements.
Input
ITP_CLK[1:0] are copies of BCLK that are used only in processor systems where
no debug port is implemented on the system board. ITP_CLK[1:0] are used as
BCLK[1:0] references for a debug port implemented on an interposer. If a debug
port is implemented in the system, ITP_CLK[1:0] are no connects in the system.
These are not processor signals.
Input
LINT[1:0] (Local APIC Interrupt) must connect the appropriate pins of all APIC Bus
agents. When the APIC is disabled, the LINT0 signal becomes INTR, a maskable
interrupt request signal, and LINT1 becomes NMI, a nonmaskable interrupt. INTR
and NMI are backward compatible with the signals of those names on the Pentium
processor. Both signals are asynchronous.
Both of these signals must be software configured via BIOS programming of the
APIC register space to be used either as NMI/INTR or LINT[1:0]. Because the APIC
is enabled by default after Reset, operation of these pins as LINT[1:0] is the default
configuration.
Input/
Output
LOCK# indicates to the system that a transaction must occur atomically. This signal
must connect the appropriate pins of all processor system bus agents. For a locked
sequence of transactions, LOCK# is asserted from the beginning of the first
transaction to the end of the last transaction.
When the priority agent asserts BPRI# to arbitrate for ownership of the processor
system bus, it will wait until it observes LOCK# deasserted. This enables symmetric
agents to retain ownership of the processor system bus throughout the bus locked
operation and ensure the atomicity of lock.
Mobile Intel Pentium 4 Processor-M Datasheet
85
Pin Listing and Signal Definitions
Table 37. Signal Description (Page 6 of 8)
Name
Type
Description
MCERR#
Input/
Output
MCERR# (Machine Check Error) is asserted to indicate an unrecoverable error
without a bus protocol violation. It may be driven by all processor system bus
agents.
MCERR# assertion conditions are configurable at a system level. Assertion options
are defined by the following options:
Enabled or disabled.
Asserted, if configured, for internal errors along with IERR#.
Asserted, if configured, by the request initiator of a bus transaction after it
observes an error.
Asserted by any bus agent when it observes an error in a bus transaction.
For more details regarding machine check architecture, please refer to the IA-32
Software Developer’s Manual, Volume 3: System Programming Guide.
PROCHOT#
Output
The assertion of PROCHOT# (Processor Hot) indicates that the processor die
temperature has reached its thermal limit. See Section 6 for more details.
Input
PWRGOOD (Power Good) is a processor input. The processor requires this signal
to be a clean indication that the clocks and power supplies are stable and within
their specifications. ‘Clean’ implies that the signal will remain low (capable of
sinking leakage current), without glitches, from the time that the power supplies are
turned on until they come within specification. The signal must then transition
monotonically to a high state. Figure 16 illustrates the relationship of PWRGOOD to
the RESET# signal. PWRGOOD can be driven inactive at any time, but clocks and
power must again be stable before a subsequent rising edge of PWRGOOD. It
must also meet the minimum pulse width specification in Table 22, and be followed
by a 1 to 10 ms RESET# pulse.
The PWRGOOD signal must be supplied to the processor; it is used to protect
internal circuits against voltage sequencing issues. It should be driven high
throughout boundary scan operation.
Input/
Output
REQ[4:0]# (Request Command) must connect the appropriate pins of all processor
system bus agents. They are asserted by the current bus owner to define the
currently active transaction type. These signals are source synchronous to
ADSTB0#. Refer to the AP[1:0]# signal description for details on parity checking of
these signals.
RESET#
Input
Asserting the RESET# signal resets the processor to a known state and invalidates
its internal caches without writing back any of their contents. For a power-on Reset,
RESET# must stay active for at least one millisecond after VCC and BCLK have
reached their proper specifications. On observing active RESET#, all system bus
agents will deassert their outputs within two clocks. RESET# must not be kept
asserted for more than 10 ms while PWRGOOD is asserted.
A number of bus signals are sampled at the active-to-inactive transition of RESET#
for power-on configuration. These configuration options are described in the
Section 7.1.
This signal does not have on-die termination and must be terminated on the
system board.
RS[2:0]#
Input
RS[2:0]# (Response Status) are driven by the response agent (the agent
responsible for completion of the current transaction), and must connect the
appropriate pins of all processor system bus agents.
Input
RSP# (Response Parity) is driven by the response agent (the agent responsible for
completion of the current transaction) during assertion of RS[2:0]#, the signals for
which RSP# provides parity protection. It must connect to the appropriate pins of all
processor system bus agents.
A correct parity signal is high if an even number of covered signals are low and low
if an odd number of covered signals are low. While RS[2:0]# = 000, RSP# is also
high, since this indicates it is not being driven by any agent guaranteeing correct
parity.
PWRGOOD
REQ[4:0]#
RSP#
86
Mobile Intel Pentium 4 Processor-M Datasheet
Pin Listing and Signal Definitions
Table 37. Signal Description (Page 7 of 8)
Name
SKTOCC#
Type
Output
Description
SKTOCC# (Socket Occupied) will be pulled to ground by the processor. System
board designers may use this pin to determine if the processor is present.
Input
SLP# (Sleep), when asserted in Stop-Grant state, causes the processor to enter the
Sleep state. During Sleep state, the processor stops providing internal clock signals
to all units, leaving only the Phase-Locked Loop (PLL) still operating. Processors in
this state will not recognize snoops or interrupts. The processor will only recognize
the assertion of the RESET# signal, deassertion of SLP#, and assertion of DPSLP#
input while in Sleep state. If SLP# is deasserted, the processor exits Sleep state
and returns to Stop-Grant state, restarting its internal clock signals to the bus and
processor core units. If the BCLK input is stopped or if DPSLP# is asserted while in
the Sleep state, the processor will exit the Sleep state and transition to the Deep
Sleep state.
Input
SMI# (System Management Interrupt) is asserted asynchronously by system logic.
On accepting a System Management Interrupt, the processor saves the current
state and enter System Management Mode (SMM). An SMI Acknowledge
transaction is issued, and the processor begins program execution from the SMM
handler.
If SMI# is asserted during the deassertion of RESET# the processor will tristate its
outputs.
STPCLK#
Input
Assertion of STPCLK# (Stop Clock) causes the processor to enter a low power
Stop-Grant state. The processor issues a Stop-Grant Acknowledge transaction, and
stops providing internal clock signals to all processor core units except the system
bus and APIC units. The processor continues to snoop bus transactions and
service interrupts while in Stop-Grant state. When STPCLK# is deasserted, the
processor restarts its internal clock to all units and resumes execution. The
assertion of STPCLK# has no effect on the bus clock; STPCLK# is an
asynchronous input.
TCK
Input
TCK (Test Clock) provides the clock input for the processor Test Bus (also known
as the Test Access Port).
TDI
Input
TDI (Test Data In) transfers serial test data into the processor. TDI provides the
serial input needed for JTAG specification support.
TDO
Output
TDO (Test Data Out) transfers serial test data out of the processor. TDO provides
the serial output needed for JTAG specification support.
TESTHI[10:8]
TESTHI[5:0]
Input
TESTHI[10:8] and TESTHI[5:0] must be connected to a VCC power source through
a resistor for proper processor operation. See Section 2.5 for more details.
THERMDA
Other
Thermal Diode Anode. See Section 6.
THERMDC
Other
Thermal Diode Cathode. See Section 6.
SLP#
SMI#
Mobile Intel Pentium 4 Processor-M Datasheet
87
Pin Listing and Signal Definitions
Table 37. Signal Description (Page 8 of 8)
Name
THERMTRIP#
Description
Output
Assertion of THERMTRIP# (Thermal Trip) indicates the processor junction
temperature has reached a level beyond which permanent silicon damage may
occur. Measurement of the temperature is accomplished through an internal
thermal sensor which is configured to trip at approximately 135°C. Upon assertion
of THERMTRIP#, the processor will shut off its internal clocks (thus halting program
execution) in an attempt to reduce the processor junction temperature. To protect
the processor, its core voltage (Vcc) must be removed following the assertion of
THERMTRIP#. See Figure 19 and Table 22 for the appropriate power down
sequence and timing requirements.
For processors with CPUID of 0xF24:
Once activated, THERMTRIP# remains latched until RESET# is asserted. While
the assertion of the RESET# signal will de-assert THERMTRIP#, if the processor’s
junction temperature remains at or above the trip level, THERMTRIP# will again be
asserted.
For processors with CPUID of 0xF27 or higher:
Driving of the THERMTRIP# signal is enabled within 10 us of the assertion of
PWRGOOD and is disabled on de-assertion of PWRGOOD. Once activated,
THERMTRIP# remains latched until PWRGOOD is de-asserted. While the deassertion of the PWRGOOD signal will de-assert THERMTRIP#, if the processor’s
junction temperature remains at or above the trip level, THERMTRIP# will again be
asserted within 10 us of the assertion of PWRGOOD.
TMS
Input
TMS (Test Mode Select) is a JTAG specification support signal used by debug
tools.
TRDY#
Input
TRDY# (Target Ready) is asserted by the target to indicate that it is ready to receive
a write or implicit writeback data transfer. TRDY# must connect the appropriate pins
of all system bus agents.
TRST#
Input
TRST# (Test Reset) resets the Test Access Port (TAP) logic. TRST# must be driven
low during power on Reset. This can be done with a 680 ohm pull-down resistor.
VCCA
Input
VCCA provides isolated power for the internal processor core PLL’s. Refer to the
Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform
Design Guide for complete implementation details.
VCCIOPLL
Input
VCCIOPLL provides isolated power for internal processor system bus PLL’s. Follow the
guidelines for VCCA, and refer to the Mobile Intel Pentium 4 Processor-M and
Intel 845MP/845MZ Chipset Platform Design Guide for complete implementation
details.
VCCSENSE
Output
VCCSENSE is an isolated low impedance connection to processor core power (VCC). It
can be used to sense or measure power near the silicon with little noise.
VCCVID
Input
VID[4:0]
VSSA
VSSSENSE
88
Type
Output
Input
Output
Independent 1.2-V supply must be routed to VCCVID pin for the Mobile Intel
Pentium 4 Processor-M’s Voltage Identification circuit.
VID[4:0] (Voltage ID) pins are used to support automatic selection of power supply
voltages (Vcc). Unlike some previous generations of processors, these are open
drain signals that are driven by the Mobile Intel Pentium 4 Processor-M and must
be pulled up to 3.3 V (max.) with 1-Kohm resistors. The voltage supply for these
pins must be valid before the VR can supply Vcc to the processor. Conversely, the
VR output must be disabled until the voltage supply for the VID pins becomes valid.
The VID pins are needed to support the processor voltage specification variations.
See Table 3 for definitions of these pins. The VR must supply the voltage that is
requested by the pins, or disable itself.
VSSA is the isolated ground for internal PLLs.
VSSSENSE is an isolated low impedance connection to processor core VSS. It can be
used to sense or measure ground near the silicon with little noise.
Mobile Intel Pentium 4 Processor-M Datasheet
Thermal Specifications and Design Considerations
6.
Thermal Specifications and Design
Considerations
In order to achieve proper cooling of the processor, a thermal solution (e.g., heat spreader, heat
pipe, or other heat transfer system) must make firm contact to the exposed processor die. The
processor die must be clean before the thermal solution is attached or the processor may be
damaged.
Table 38 provides the Thermal Design Power (TDP) dissipation and the minimum and maximum
TJ temperatures for the Mobile Intel Pentium 4 Processor-M. A thermal solution should be
designed to ensure the junction temperature remains within the minimum and maximum TJ
specifications while operating at the Thermal Design Power. Additionally, a secondary failsafe
mechanism in hardware would be provided to shutdown the processor under catastrophic thermal
conditions, as described in Section 2.4.3. TDP is a thermal design power specification based on the
worst case power dissipation of the processor while executing publicly available software under
normal operating conditions at nominal voltages. Contact your Intel Field Sales Representative for
further information.
Table 38. Power Specifications for the Mobile Intel Pentium 4 Processor-M
Symbol
Parameter
TDP
Thermal Design Power at
2.6 GHz & 1.3 V
2.5 GHz & 1.3 V
2.4 GHz & 1.3 V
2.2 GHz & 1.3 V
2.0 GHz & 1.3 V
1.9 GHz & 1.3 V
1.8 GHz & 1.3 V
1.7 GHz & 1.3 V
1.6 GHz & 1.3 V
1.5 GHz & 1.3 V
1.4 GHz & 1.3 V
1.2 GHz & 1.2 V
PAH
PSGNT
PSLP
Auto Halt/Stop Grant/Sleep
Power at
1.3 V (for >2.0 GHz)
1.3 V (for <= 2.0 GHz)
1.2 V
PDSLP
Min
Typ
Max
35.0
35.0
35.0
35.0
32.0
32.0
30.0
30.0
30.0
26.9
25.8
20.8
Unit
Notes
W
At 100°C, Note 1
8.0
7.5
5.9
W
At 50°C, Note 2
Deep Sleep Power at
1.3 V
1.2 V
5.0
4.2
W
At 35°C, Note 2
PDPRSLP
Deeper Sleep Power at
1.0 V
2.9
W
At 35°C, Note 2
TJ
Junction Temperature
°C
Note 3
0
100
NOTES:
1. TDP is defined as the worst case power dissipated by the processor while executing publicly available
software under normal operating conditions at nominal voltages that meet the load line specifications. The
TDP number shown is a specification based on ICC (maximum) at nominal voltages and indirectly tested by
this ICC (maximum) testing. TDP definition is synonymous with the Thermal Design Power (typical)
specification referred to in the previous EMTS. The Intel TDP specification is a recommended design point
Mobile Intel Pentium 4 Processor-M Datasheet
89
Thermal Specifications and Design Considerations
and is not representative of the absolute maximum power the processor may dissipate under worst case
conditions.
2. Not 100% tested. These power specifications are determined by characterization of the processor currents at
higher temperatures and extrapolating the values for the temperature indicated.
3. The maximum junction temperature (TJ) is specified as the hottest location on the die. The thermal monitor’s
automatic mode is used to indicate that the maximum TJ has been reached. Refer to Section 6.1.1 for TJ
measurement guidelines (Refer to Section 6.1.2 for thermal monitor details).
6.1
Thermal Specifications
6.1.1
Thermal Diode
The Mobile Intel Pentium 4 Processor-M incorporates two methods of monitoring die temperature,
the thermal monitor and the thermal diode. The thermal monitor (detailed in Section 6.1.2) must be
used to determine when the minimum or maximum specified processor junction temperature has
been reached. The second method, the thermal diode, can be read by an off-die analog/digital
converter (a thermal sensor) located on the motherboard, or a stand-alone measurement kit. The
thermal diode may be used to monitor the die temperature of the processor for thermal
management or instrumentation purposes but cannot be used to indicate that the maximum TJ of
the processor has been reached. Table 39 and Table 40 provide the diode interface and
specifications.
Note:
The reading of the thermal sensor connected to the thermal diode does not reflect the temperature
of the hottest location on the die (TJ). This is due to inaccuracies in the thermal diode, on-die
temperature gradients between the location of the thermal diode and the hottest location on the die,
and time based variations in the die temperature. Time based variations can occur since the
sampling rate of the sensor is much slower than the die level temperature changes.
The offset between the thermal diode based temperature reading and the hottest location of the die
(thermal monitor) may be characterized using the thermal monitor’s Automatic mode activation of
thermal control circuit. This temperature offset must be taken into account when using the
processor thermal diode to implement power management events.
Table 39. Thermal Diode Interface
Signal Name
Pin/Ball Number
Signal Description
THERMDA
B3
Thermal diode anode
THERMDC
C4
Thermal diode cathode
Table 40. Thermal Diode Specifications
Symbol
Parameter
Min
IFW
Forward Bias Current
5
n
Diode Ideality Factor
1.0012
RT
Series Resistance
Typ
1.0021
3.86
Max
Unit
300
µA
1.0030
Notes
1
2, 3, 4
ohms
2, 3, 5
NOTES:
1. Intel does not support or recommend operation of the thermal diode under reverse bias.
2. Characterized at 100°C.
3. Not 100% tested. Specified by design characterization.
4. The ideality factor, n, represents the deviation from ideal diode behavior as exemplified by the diode
equation:
IFW=Is *(e(qVD/nkT) -1)
90
Mobile Intel Pentium 4 Processor-M Datasheet
Thermal Specifications and Design Considerations
Where IS = saturation current, q = electronic charge, VD = voltage across the diode, k = Boltzmann Constant,
and T = absolute temperature (Kelvin).
5. The series resistance, RT, is provided to allow for a more accurate measurement of the diode junction
temperature. RT as defined includes the pins of the processor but does not include any socket resistance or
board trace resistance between the socket and the external remote diode thermal sensor. RT can be used by
remote diode thermal sensors with automatic series resistance cancellation to calibrate out this error term.
Another application is that a temperature offset can be manually calculated and programmed into an offset
register in the remote diode thermal sensors as exemplified by the equation:
Terror = [RT*(N-1)*IFWmin]/[(nk/q)*ln N]
Where Terror = sensor temperature error, N = sensor current ration, k = Boltzmann Constant, q = electronic
charge.
6.1.2
Thermal Monitor
The thermal monitor feature found in the Mobile Intel Pentium 4 Processor-M allows system
designers to design lower cost thermal solutions without compromising system integrity or
reliability. By using a factory-tuned, precision on-die thermal sensor, and a fast acting thermal
control circuit (TCC), the processor, without the aid of any additional software or hardware, can
keep the processor’s die temperature within factory specifications under nearly all conditions. The
thermal monitor thus allows the processor and system thermal solutions to be designed much closer
to the power envelopes of real applications, instead of being designed to the much higher
maximum processor power envelopes.
The thermal monitor controls the processor temperature by modulating (starting and stopping) the
processor core clocks. The processor clocks are modulated when the thermal control circuit (TCC)
is activated. The thermal monitor uses two modes to activate the TCC: Automatic mode and OnDemand mode. Automatic mode is required for the processor to operate within specifications
and must first be enabled via BIOS. Once automatic mode is enabled, the TCC will activate only
when the internal die temperature is very near the temperature limits of the processor. When TCC
is enabled, and a high temperature situation exists (i.e. TCC is active), the clocks will be modulated
by alternately turning the clocks off and on at a duty cycle specific to the processor (typically
30-50%). An under-designed thermal solution that is not able to prevent excessive activation of the
TCC in the anticipated ambient environment may cause a noticeable performance loss. Cycle times
are processor speed dependent and will decrease linearly as processor core frequencies increase.
Once the temperature has returned to a non-critical level, modulation ceases and TCC goes
inactive. A small amount of hysteresis has been included to prevent rapid active/inactive transitions
of the TCC when the processor temperature is near the trip point. Processor performance will be
decreased by approximately the same amount as the duty cycle when the TCC is active, however,
with a properly designed and characterized thermal solution, the TCC will only be activated briefly
when running the most power intensive applications in a high ambient temperature environment.
For automatic mode, the duty cycle is factory configured and cannot be modified. Also, automatic
mode does not require any additional hardware, software drivers or interrupt handling routines.
The TCC may also be activated via On-Demand mode. If bit 4 of the ACPI Thermal Monitor
Control register is written to a 1 the TCC will be activated immediately, independent of the
processor temperature. When using On-Demand mode to activate the TCC, the duty cycle of the
clock modulation is programmable via bits 3:1 of the same ACPI Thermal Monitor Control
register. In automatic mode, the duty cycle is fixed, however in On-Demand mode, the duty cycle
can be programmed from 12.5% on/ 87.5% off, to 87.5% on/12.5% off in 12.5% increments. OnDemand mode may be used at the same time Automatic mode is enabled, however, if the system
tries to enable the TCC via On-Demand mode at the same time automatic mode is enabled AND a
high temperature condition exists, the duty cycle of the automatic mode will override the duty
cycle selected by the On-Demand mode.
Mobile Intel Pentium 4 Processor-M Datasheet
91
Thermal Specifications and Design Considerations
An external signal, PROCHOT# (processor hot) is asserted when the processor die temperature has
reached its thermal limit. If the TCC is enabled (note that the TCC must be enabled for the
processor to be operating within spec), TCC will be active when the PROCHOT# signal is active.
The temperature at which the thermal control circuit activates is not user configurable and is not
software visible. Bus snooping and interrupt latching are active while the TCC is active.
Besides the thermal sensor and TCC, the thermal monitor feature also includes one ACPI register,
performance monitoring logic, bits in three model specific registers (MSR), and one I/O pin
(PROCHOT#). All are available to monitor and control the state of the thermal monitor feature.
Thermal monitor can be configured to generate an interrupt upon the assertion or de-assertion of
PROCHOT#.
If automatic mode is disabled the processor will be operating out of specification. Regardless of
enabling of the automatic or On-Demand modes, in the event of a catastrophic cooling failure, the
processor will automatically shut down when the silicon has reached a temperature of
approximately 135 °C. At this point the system bus signal THERMTRIP# will go active and stay
active until RESET# has been initiated. THERMTRIP# activation is independent of processor
activity and does not generate any bus cycles. If THERMTRIP# is asserted, processor core voltage
(VCC) must be removed within the timeframe defined in Table 22.
92
Mobile Intel Pentium 4 Processor-M Datasheet
Configuration and Low Power Features
7.
Configuration and Low Power Features
7.1
Power-On Configuration Options
Several configuration options can be configured by hardware. The Mobile Intel Pentium 4
Processor-M samples its hardware configuration at reset, on the active-to-inactive transition of
RESET#. For specifications on these options, please refer to Table 41.
Frequency determination functionality will exist on engineering sample processors which means
that samples can run at varied frequencies. Production material will have the bus to core ratio
locked during manufacturing and can only be operated at the rated frequency.
The sampled information configures the processor for subsequent operation. These configuration
options cannot be changed except by another reset. All resets reconfigure the processor.
Table 41. Power-On Configuration Option Pins
Pin1
Configuration Option
Output tristate
SMI#
Execute BIST
INIT#
In Order Queue pipelining (set IOQ depth to 1)
A7#
Disable MCERR# observation
A9#
Disable BINIT# observation
A10#
APIC Cluster ID (0-3)
A[12:11]#
Disable bus parking
A15#
Symmetric agent arbitration ID
BR0#
NOTE: Asserting this signal during RESET# will select the corresponding option.
7.2
Clock Control and Low Power States
The use of AutoHALT, Stop-Grant, Sleep, Deep Sleep and Deeper Sleep states is allowed in
Mobile Intel Pentium 4 Processor-M based systems to reduce power consumption by stopping the
clock to internal sections of the processor, depending on each particular state. See Figure 35 for a
visual representation of the processor low-power states.
7.2.1
Normal State
This is the normal operating state for the processor.
7.2.2
AutoHALT Powerdown State
AutoHALT is a low-power state entered when the processor executes the HALT instruction. The
processor will transition to the Normal state upon the occurrence of SMI#, BINIT#, INIT#,
LINT[1:0] (NMI, INTR), or PSB interrupt message. RESET# will cause the processor to
immediately initialize itself.
Mobile Intel Pentium 4 Processor-M Datasheet
93
Configuration and Low Power Features
The return from a System Management Interrupt (SMI) handler can be to either Normal Mode or
the AutoHALT Powerdown state. See the Intel Architecture Software Developer's Manual, Volume
III: System Programmer's Guide for more information.
The system can generate a STPCLK# while the processor is in the AutoHALT Powerdown state.
When the system deasserts the STPCLK# interrupt, the processor will return execution to the
HALT state.
While in AutoHALT Powerdown state, the processor will process bus snoops.
Figure 35. Clock Control States
SLP# asserted
STPCLK# asserted
Normal STPCLK# de-asserted
Stop
Grant
Sleep
SLP# de-asserted
halt
break HLT
instruction
Auto Halt
STPCLK#
asserted
DPSLP#
de-asserted
snoop
snoop
STPCLK# serviced occurs
de-asserted
snoop
occurs
snoop
serviced
DPSLP#
asserted
core voltage raised
HALT/
Grant
Snoop
Deeper
Sleep
Deep
Sleep
core voltage lowered
V0001-04
Halt break - A20M#, BINIT#, INIT#, INTR, NMI, PREQ#, RESET#, SMI#, or APIC interrupt
7.2.3
Stop-Grant State
When the STPCLK# pin is asserted, the Stop-Grant state of the processor is entered 20 bus clocks
after the response phase of the processor-issued Stop Grant Acknowledge special bus cycle.
Since the AGTL+ signal pins receive power from the system bus, these pins should not be driven
(allowing the level to return to VCC) for minimum power drawn by the termination resistors in this
state. In addition, all other input pins on the system bus should be driven to the inactive state.
BINIT# will not be serviced while the processor is in Stop-Grant state. The event will be latched
and can be serviced by software upon exit from the Stop-Grant state.
RESET# will cause the processor to immediately initialize itself, but the processor will stay in
Stop-Grant state. A transition back to the Normal state will occur with the de-assertion of the
STPCLK# signal. When re-entering the Stop-Grant state from the Sleep state, STPCLK# should
only be de-asserted ten or more bus clocks after the deassertion of SLP#.
A transition to the HALT/Grant Snoop state will occur when the processor detects a snoop on the
system bus (see Section 7.2.4). A transition to the Sleep state (see Section 7.2.5) will occur with the
assertion of the SLP# signal.
94
Mobile Intel Pentium 4 Processor-M Datasheet
Configuration and Low Power Features
While in the Stop-Grant State, SMI#, INIT#, BINIT# and LINT[1:0] will be latched by the
processor, and only serviced when the processor returns to the Normal State. Only one occurrence
of each event will be recognized upon return to the Normal state.
While in Stop-Grant state, the processor will process a system bus snoop.
7.2.4
HALT/Grant Snoop State
The processor will respond to snoop transactions on the system bus while in Stop-Grant state or in
AutoHALT Power Down state. During a snoop transaction, the processor enters the HALT/Grant
Snoop state. The processor will stay in this state until the snoop on the system bus has been
serviced (whether by the processor or another agent on the system bus). After the snoop is serviced,
the processor will return to the Stop-Grant state or AutoHALT Power Down state, as appropriate.
7.2.5
Sleep State
The Sleep state is a low power state in which the processor maintains its context, maintains the
phase-locked loop (PLL), and has stopped all internal clocks. The Sleep state can only be entered
from Stop-Grant state. Once in the Stop-Grant state, the processor will enter the Sleep state upon
the assertion of the SLP# signal. The SLP# pin should only be asserted when the processor is in the
Stop Grant state. SLP# assertions while the processor is not in the Stop-Grant state is out of
specification and may result in unapproved operation.
Snoop events that occur while in Sleep State or during a transition into or out of Sleep state will
cause unpredictable behaviour.
In the Sleep state, the processor is incapable of responding to snoop transactions or latching
interrupt signals. No transitions or assertions of signals (with the exception of SLP#, DPSLP# or
RESET#) are allowed on the system bus while the processor is in Sleep state. Any transition on an
input signal before the processor has returned to Stop-Grant state will result in unpredictable
behaviour.
If RESET# is driven active while the processor is in the Sleep state, and held active as specified in
the RESET# pin specification, then the processor will reset itself, ignoring the transition through
Stop-Grant State. If RESET# is driven active while the processor is in the Sleep State, the SLP#
and STPCLK# signals should be deasserted immediately after RESET# is asserted to ensure the
processor correctly executes the Reset sequence.
While in the Sleep state, the processor is capable of entering an even lower power state, the Deep
Sleep state, by asserting the DPSLP# pin. (See Section 7.2.6.) Once in the Sleep or Deep Sleep
states, the SLP# pin must be de-asserted if another asynchronous system bus event needs to occur.
The SLP# pin has a minimum assertion of one BCLK period.
When the processor is in Sleep state, it will not respond to interrupts or snoop transactions.
7.2.6
Deep Sleep State
Deep Sleep state is a very low power state the processor can enter while maintaining context. Deep
Sleep state is entered by asserting the DPSLP# pin. The DPSLP# pin must be de-asserted to reenter the Sleep state. A period of 30 microseconds (to allow for PLL stabilization) must occur
before the processor can be considered to be in the Sleep State. Once in the Sleep state, the SLP#
pin can be deasserted to re-enter the Stop-Grant state.
Mobile Intel Pentium 4 Processor-M Datasheet
95
Configuration and Low Power Features
The clock may be stopped when the processor is in the Deep Sleep state in order to support the
ACPI S1 state. The clock may only be stopped after DPSLP# is asserted and must be restarted
before DPSLP# is deasserted. To provide maximum power conservation when stopping the clock
during Deep Sleep, hold the BLCK0 input at VOL and the BCLK1 input at VOH.
While in Deep Sleep state, the processor is incapable of responding to snoop transactions or
latching interrupt signals. No transitions of signals are allowed on the system bus while the
processor is in Deep Sleep state. Any transition on an input signal before the processor has returned
to Stop-Grant state will result in unpredictable behaviour.
7.2.7
Deeper Sleep State
The Deeper Sleep State is the lowest state power the processor can enter. This state is functionally
identical to the Deep Sleep state but at a lower core voltage. The control signals to the voltage
regulator to initiate a transition to the Deeper Sleep state are provided on the platform. Please refer
the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset Platform Design
Guide.
7.3
Enhanced Intel SpeedStep Technology
The Mobile Intel Pentium 4 Processor-M, when used in conjunction with the requisite Intel
SpeedStep technology applet or its equivalent, supports Enhanced Intel SpeedStep technology.
Enhanced Intel SpeedStep technology allows the processor to switch between two core frequencies
automatically based on CPU demand, without having to reset the processor or change the system
bus frequency. The processor has two bus ratios and voltages programmed into it instead of one
and the GHI# signal controls which bus ratio and voltage is used. After reset, the processor will
start in the lower of its two core frequencies, the “Battery Optimized” mode. An operating mode
transition to the high core frequency can be made by setting GHI# low, putting the processor into
the Deep Sleep state, regulating to the new VID output, and returning to the Normal state. This puts
the processor into the high core frequency, or “Maximum Performance” operating mode. Going
through these steps with GHI# set high, transitions the processor back to the low core frequency
operating mode. The processor will drive the VID[4:0] pins with the VID of the current operating
mode and the system logic is required to regulate the core voltage within specification for the
driven VID.
96
Mobile Intel Pentium 4 Processor-M Datasheet
Debug Tools Specifications
8.
Debug Tools Specifications
Please refer to the Mobile Intel Pentium 4 Processor-M and Intel 845MP/845MZ Chipset
Platform Design Guide for information regarding debug tools specifications.
8.1
Logic Analyzer Interface (LAI)
Intel is working with two logic analyzer vendors to provide logic analyzer interfaces (LAIs) for use
in debugging Mobile Intel Pentium 4 Processor-M systems. Tektronix* and Agilent* should be
contacted to get specific information about their logic analyzer interfaces. The following
information is general in nature. Specific information must be obtained from the logic analyzer
vendor.
Due to the complexity of Mobile Intel Pentium 4 Processor-M systems, the LAI is critical in
providing the ability to probe and capture system bus signals. There are two sets of considerations
to keep in mind when designing a Mobile Intel Pentium 4 Processor-M system that can make use of
an LAI: mechanical and electrical.
8.1.1
Mechanical Considerations
The LAI is installed between the processor socket and the Mobile Intel Pentium 4 Processor-M.
The LAI pins plug into the socket, while the Mobile Intel Pentium 4 Processor-M pins plug into a
socket on the LAI. Cabling that is part of the LAI egresses the system to allow an electrical
connection between the Mobile Intel Pentium 4 Processor-M and a logic analyzer. The maximum
volume occupied by the LAI, known as the keepout volume, as well as the cable egress restrictions,
should be obtained from the logic analyzer vendor. System designers must make sure that the
keepout volume remains unobstructed inside the system.
8.1.2
Electrical Considerations
The LAI will also affect the electrical performance of the system bus; therefore, it is critical to
obtain electrical load models from each of the logic analyzer vendors to be able to run system level
simulations to prove that their tool will work in the system. Contact the logic analyzer vendor for
electrical specifications and load models for the LAI solution they provide.
Mobile Intel Pentium 4 Processor-M Datasheet
97