Intel® Core™2 Duo Processor E8000Δ and E7000Δ Series Datasheet June 2009 Document Number: 318732-006 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR ANY APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The Intel Core™2 Duo processor E8000 and E7000 series may contain design defects or errors known as errata which may cause the product to deviate from published specifications. ΔIntel processor numbers are not a measure of performance. Processor numbers differentiate features within each processor family, not across different processor families. See http://www.intel.com/products/processor_number for details. Over time processor numbers will increment based on changes in clock, speed, cache, FSB, or other features, and increments are not intended to represent proportional or quantitative increases in any particular feature. Current roadmap processor number progression is not necessarily representative of future roadmaps. See www.intel.com/products/ processor_number for details. ΦIntel® 64 requires a computer system with a processor, chipset, BIOS, operating system, device drivers and applications enabled for Intel 64. Processor will not operate (including 32-bit operation) without an Intel 64-enabled BIOS. Performance will vary depending on your hardware and software configurations. See http://developer.intel.com/technology/intel64/ for more information including details on which processors support Intel 64 or consult with your system vendor for more information. Enabling Execute Disable Bit functionality requires a PC with a processor with Execute Disable Bit capability and a supporting operating system. Check with your PC manufacturer on whether your system delivers Execute Disable Bit functionality. Intel® Virtualization Technology requires a computer system with a processor, chipset, BIOS, virtual machine monitor (VMM) and for some uses, certain platform software enabled for it. Functionality, performance or other benefit will vary depending on hardware and software configurations and may require a BIOS update. Software applications may not be compatible with all operating systems. Please check with your application vendor. See the Processor Spec Finder or contact your Intel representative for more information. No computer system can provide absolute security under all conditions. Intel® Trusted Execution Technology (Intel® TXT) requires a computer system with Intel® Virtualization Technology, an Intel TXT-enabled processor, chipset, BIOS, Authenticated Code Modules and an Intel TXT-compatible measured launched environment (MLE). The MLE could consist of a virtual machine monitor, an OS or an application. In addition, Intel TXT requires the system to contain a TPM v1.2, as defined by the Trusted Computing Group and specific software for some uses. For more information, see here Not all specified units of this processor support Thermal Monitor 2, Enhanced HALT State and Enhanced Intel SpeedStep® Technology. See the Processor Spec Finder at http://processorfinder.intel.com or contact your Intel representative for more information. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Intel, Pentium, Intel Core, Intel SpeedStep, and the Intel logo are trademarks of Intel Corporation in the U.S. and other countries. * Other names and brands may be claimed as the property of others. Copyright © 2008–2009, Intel Corporation. All rights reserved. 2 Datasheet Contents 1 Introduction .............................................................................................................. 9 1.1 Terminology ..................................................................................................... 10 1.1.1 Processor Terminology Definitions ............................................................ 10 1.2 References ....................................................................................................... 12 2 Electrical Specifications ........................................................................................... 13 2.1 Power and Ground Lands.................................................................................... 13 2.2 Decoupling Guidelines ........................................................................................ 13 2.2.1 VCC Decoupling ..................................................................................... 13 2.2.2 VTT Decoupling ...................................................................................... 13 2.2.3 FSB Decoupling...................................................................................... 14 2.3 Voltage Identification ......................................................................................... 14 2.4 Reserved, Unused, and TESTHI Signals ................................................................ 16 2.5 Power Segment Identifier (PSID)......................................................................... 16 2.6 Voltage and Current Specification ........................................................................ 17 2.6.1 Absolute Maximum and Minimum Ratings .................................................. 17 2.6.2 DC Voltage and Current Specification ........................................................ 18 2.6.3 VCC Overshoot ...................................................................................... 23 2.6.4 Die Voltage Validation ............................................................................. 24 2.7 Signaling Specifications...................................................................................... 24 2.7.1 FSB Signal Groups.................................................................................. 25 2.7.2 CMOS and Open Drain Signals ................................................................. 26 2.7.3 Processor DC Specifications ..................................................................... 27 2.7.3.1 Platform Environment Control Interface (PECI) DC Specifications..... 29 2.7.3.2 GTL+ Front Side Bus Specifications ............................................. 30 2.8 Clock Specifications ........................................................................................... 31 2.8.1 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking ............................ 31 2.8.2 FSB Frequency Select Signals (BSEL[2:0])................................................. 32 2.8.3 Phase Lock Loop (PLL) and Filter .............................................................. 32 2.8.4 BCLK[1:0] Specifications ......................................................................... 32 3 Package Mechanical Specifications .......................................................................... 35 3.1 Package Mechanical Drawing............................................................................... 35 3.2 Processor Component Keep-Out Zones ................................................................. 39 3.3 Package Loading Specifications ........................................................................... 39 3.4 Package Handling Guidelines............................................................................... 39 3.5 Package Insertion Specifications.......................................................................... 40 3.6 Processor Mass Specification ............................................................................... 40 3.7 Processor Materials............................................................................................ 40 3.8 Processor Markings............................................................................................ 40 3.9 Processor Land Coordinates ................................................................................ 41 4 Land Listing and Signal Descriptions ....................................................................... 43 4.1 Processor Land Assignments ............................................................................... 43 4.2 Alphabetical Signals Reference ............................................................................ 66 5 Thermal Specifications and Design Considerations .................................................. 77 5.1 Processor Thermal Specifications ......................................................................... 77 5.1.1 Thermal Specifications ............................................................................ 77 5.1.2 Thermal Metrology ................................................................................. 81 5.2 Processor Thermal Features ................................................................................ 81 5.2.1 Thermal Monitor..................................................................................... 81 5.2.2 Thermal Monitor 2 .................................................................................. 82 5.2.3 On-Demand Mode .................................................................................. 83 5.2.4 PROCHOT# Signal .................................................................................. 84 5.2.5 THERMTRIP# Signal ............................................................................... 84 5.3 Platform Environment Control Interface (PECI) ...................................................... 85 5.3.1 Introduction .......................................................................................... 85 5.3.1.1 TCONTROL and TCC activation on PECI-Based Systems.................. 85 5.3.2 PECI Specifications ................................................................................. 86 5.3.2.1 PECI Device Address ................................................................. 86 Datasheet 3 5.3.2.2 5.3.2.3 5.3.2.4 PECI Command Support .............................................................86 PECI Fault Handling Requirements ...............................................86 PECI GetTemp0() Error Code Support ..........................................86 6 Features ..................................................................................................................87 6.1 Power-On Configuration Options ..........................................................................87 6.2 Clock Control and Low Power States .....................................................................87 6.2.1 Normal State .........................................................................................88 6.2.2 HALT and Extended HALT Powerdown States ..............................................88 6.2.2.1 HALT Powerdown State ..............................................................88 6.2.2.2 Extended HALT Powerdown State ................................................89 6.2.3 Stop Grant and Extended Stop Grant States ...............................................89 6.2.3.1 Stop-Grant State.......................................................................89 6.2.3.2 Extended Stop Grant State .........................................................90 6.2.4 Extended HALT Snoop State, HALT Snoop State, Extended Stop Grant Snoop State, and Stop Grant Snoop State..................................90 6.2.4.1 HALT Snoop State, Stop Grant Snoop State ..................................90 6.2.4.2 Extended HALT Snoop State, Extended Stop Grant Snoop State.......90 6.2.5 Sleep State ............................................................................................90 6.2.6 Deep Sleep State....................................................................................91 6.2.7 Deeper Sleep State .................................................................................91 6.2.8 Enhanced Intel SpeedStep® Technology ....................................................92 6.3 Processor Power Status Indicator (PSI) Signal .......................................................92 7 Boxed Processor Specifications................................................................................93 7.1 Introduction ......................................................................................................93 7.2 Mechanical Specifications ....................................................................................94 7.2.1 Boxed Processor Cooling Solution Dimensions.............................................94 7.2.2 Boxed Processor Fan Heatsink Weight .......................................................95 7.2.3 Boxed Processor Retention Mechanism and Heatsink Attach Clip Assembly .....95 7.3 Electrical Requirements ......................................................................................95 7.3.1 Fan Heatsink Power Supply ......................................................................95 7.4 Thermal Specifications........................................................................................97 7.4.1 Boxed Processor Cooling Requirements......................................................97 7.4.2 Variable Speed Fan .................................................................................99 8 Debug Tools Specifications .................................................................................... 101 8.1 Logic Analyzer Interface (LAI) ........................................................................... 101 8.1.1 Mechanical Considerations ..................................................................... 101 8.1.2 Electrical Considerations ........................................................................ 101 4 Datasheet Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Datasheet Intel® Core™2 Duo Processor E8000 Series VCC Static and Transient Tolerance................ 21 Intel® Core™2 Duo Processor E7000 Series VCC Static and Transient Tolerance................ 23 VCC Overshoot Example Waveform ............................................................................. 24 Differential Clock Waveform ...................................................................................... 34 Measurement Points for Differential Clock Waveforms ................................................... 34 Processor Package Assembly Sketch ........................................................................... 35 Processor Package Drawing Sheet 1 of 3 ..................................................................... 36 Processor Package Drawing Sheet 2 of 3 ..................................................................... 37 Processor Package Drawing Sheet 3 of 3 ..................................................................... 38 Processor Top-Side Markings Example ........................................................................ 40 Processor Land Coordinates and Quadrants, Top View ................................................... 41 land-out Diagram (Top View – Left Side) ..................................................................... 44 land-out Diagram (Top View – Right Side) ................................................................... 45 Intel® Core™2 Duo Processor E8000 Series Thermal Profile ........................................... 79 Intel® Core™2 Duo Processor E7000 Series Thermal Profile ........................................... 80 Case Temperature (TC) Measurement Location ............................................................ 81 Thermal Monitor 2 Frequency and Voltage Ordering ...................................................... 83 Conceptual Fan Control Diagram on PECI-Based Platforms............................................. 85 Processor Low Power State Machine ........................................................................... 88 Mechanical Representation of the Boxed Processor ....................................................... 93 Space Requirements for the Boxed Processor (Side View).............................................. 94 Space Requirements for the Boxed Processor (Top View)............................................... 94 Overall View Space Requirements for the Boxed Processor............................................. 95 Boxed Processor Fan Heatsink Power Cable Connector Description .................................. 96 Baseboard Power Header Placement Relative to Processor Socket ................................... 97 Boxed Processor Fan Heatsink Airspace Keepout Requirements (side 1 view) ................... 98 Boxed Processor Fan Heatsink Airspace Keepout Requirements (side 2 view) ................... 98 Boxed Processor Fan Heatsink Set Points..................................................................... 99 5 Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 6 References ..............................................................................................................12 Voltage Identification Definition ..................................................................................15 Absolute Maximum and Minimum Ratings ....................................................................17 Voltage and Current Specifications..............................................................................18 Intel® Core™2 Duo Processor E8000 Series VCC Static and Transient Tolerance ................20 Intel® Core™2 Duo Processor E7000 Series VCC Static and Transient Tolerance ................22 VCC Overshoot Specifications......................................................................................23 FSB Signal Groups ....................................................................................................25 Signal Characteristics................................................................................................26 Signal Reference Voltages .........................................................................................26 GTL+ Signal Group DC Specifications ..........................................................................27 Open Drain and TAP Output Signal Group DC Specifications ...........................................27 CMOS Signal Group DC Specifications..........................................................................28 PECI DC Electrical Limits ...........................................................................................29 GTL+ Bus Voltage Definitions .....................................................................................30 Core Frequency to FSB Multiplier Configuration.............................................................31 BSEL[2:0] Frequency Table for BCLK[1:0] ...................................................................32 Front Side Bus Differential BCLK Specifications .............................................................32 FSB Differential Clock Specifications (1333 MHz FSB) ....................................................33 FSB Differential Clock Specifications (1066 MHz FSB) ....................................................33 Processor Loading Specifications.................................................................................39 Package Handling Guidelines......................................................................................39 Processor Materials ...................................................................................................40 Alphabetical Land Assignments...................................................................................46 Numerical Land Assignment .......................................................................................56 Signal Description.....................................................................................................66 Processor Thermal Specifications ................................................................................78 Intel® Core™2 Duo Processor E8000 Series Thermal Profile ...........................................79 Intel® Core™2 Duo Processor E7000 Series Thermal Profile ...........................................80 GetTemp0() Error Codes ...........................................................................................86 Power-On Configuration Option Signals .......................................................................87 Fan Heatsink Power and Signal Specifications ...............................................................96 Fan Heatsink Power and Signal Specifications ............................................................. 100 Datasheet Intel® Core™2 Duo Processor E8000 and E7000 Series Features • Available at 3.33 GHz, 3.16 GHz, 3.00 GHz, 2.83 GHz, and 2.66 GHz for the Intel Core™2 Duo processor E8000 series • Available at 3.06 GHz, 2.93 GHz, 2.80 GHz, 2.66 GHz, and 2.53 GHz for the Intel Core™2 Duo processor E7000 series • Enhanced Intel Speedstep® Technology • Supports Intel® 64Φ architecture • Supports Intel® Virtualization Technology (Intel® VT) (Intel Core™2 Duo processors E8600, E8500, E8400, E8300, E8200 and E7600 only) • Supports Intel® Trusted Execution Technology (Intel® TXT) (Intel Core™2 Duo processors E8600, E8500, E8400, E8300, and E8200 only) • Supports Execute Disable Bit capability • FSB frequency at 1333 MHz • FSB frequency at 1066 MHz (Intel Core™2 Duo processor E7000 series only) • Binary compatible with applications running on previous members of the Intel microprocessor line • • • • Advance Dynamic Execution Very deep out-of-order execution Enhanced branch prediction Optimized for 32-bit applications running on advanced 32-bit operating systems • Intel® Advanced Smart Cache • 6 MB Level 2 cache (Intel Core™2 Duo processor E8000 series only) • 3 MB Level 2 cache (Intel Core™2 Duo processor E7000 series only) • Intel® Advanced Digital Media Boost • Enhanced floating point and multimedia unit for enhanced video, audio, encryption, and 3D performance • Power Management capabilities • System Management mode • Multiple low-power states • 8-way cache associativity provides improved cache hit rate on load/store operations • 775-land Package The Intel® Core™2 Duo processor E8000 and E7000 series are based on the Enhanced Intel® Core™ microarchitecture. The Enhanced Intel® Core™ microarchitecture combines the performance across applications and usages where end-users can truly appreciate and experience the performance. These applications include Internet audio and streaming video, image processing, video content creation, speech, 3D, CAD, games, multimedia, and multitasking user environments. Intel® 64Φ architecture enables the processor to execute operating systems and applications written to take advantage of the Intel 64 architecture. The processor, supporting Enhanced Intel Speedstep® technology, allows tradeoffs to be made between performance and power consumption. The Intel Core™2 Duo processor E8000 and E7000 series also includes the Execute Disable Bit capability. This feature, combined with a supported operating system, allows memory to be marked as executable or non-executable. Virtualization Technology provides silicon-based functionality that works together with compatible Virtual Machine Monitor (VMM) software to improve on software-only solutions. The Intel® Trusted Execution Technology (Intel TXT) is a key element in Intel's safer computing initiative that defines a set of hardware enhancements that interoperate with an Intel TXT enabled operating system to help protect against software-based attacks. It creates a hardware foundation that builds on Intel's Virtualization Technology to help protect the confidentiality and integrity of data stored/created on the client PC. Datasheet 7 Revision History Revision Number -001 Description • Initial release • Added -002 Intel® Revision Date January 2008 Core™2 Duo processor E8300 and E7200 • Updated VID information. Updated Table 2-1. April 2008 • Added the PSI# signal -003 • Added Intel® Core™2 Duo processor E8600 and E7300 • Updated FSB termination voltage in Table 2-3. August 2008 -004 • Added Intel® Core™2 Duo processor E7400 October 2008 -005 • Added Intel® Core™2 Duo processor E7500 January 2009 -006 • Added Intel® Core™2 Duo processor E7600 June 2009 §§ 8 Datasheet Introduction 1 Introduction The Intel® Core™2 Duo processor E8000 and E7000 series is based on the Enhanced Intel® Core™ microarchitecture. The Intel Enhanced Core™ microarchitecture combines the performance of previous generation Desktop products with the power efficiencies of a low-power microarchitecture to enable smaller, quieter systems. The Intel® Core™2 Duo processor E8000 and E7000 series are 64-bit processors that maintain compatibility with IA-32 software. Note: In this document, the Intel® Core™2 Duo processor E8000 and E7000 series may be referred to as "the processor." Note: In this document, unless otherwise specified, the Intel® Core™2 Duo processor E8000 series refers to the Intel® Core™2 Duo processors E8600, E8500, E8400, E8300, E8200, and E8190. Note: In this document, unless otherwise specified, the Intel® Core™2 Duo processor E7000 series refers to the Intel® Core™2 Duo processors E7600, E7500, E7400, E7300 and E7200. The processors use Flip-Chip Land Grid Array (FC-LGA8) package technology, and plugs into a 775-land surface mount, Land Grid Array (LGA) socket, referred to as the LGA775 socket. The processors are based on 45 nm process technology. The processors feature the Intel Advanced Smart Cache, a shared multi-core optimized cache that significantly reduces latency to frequently used data. The Intel Core™2 Duo processor E8000 series features a 1333 MHz front side bus (FSB) and 6 MB of L2 cache. The Intel Core™2 Duo processor E7000 series features a 1333 MHz and 1066 MHz front side bus (FSB) and 3 MB of L2 cache. The processors support all the existing Streaming SIMD Extensions 2 (SSE2), Streaming SIMD Extensions 3 (SSE3), Supplemental Streaming SIMD Extension 3 (SSSE3), and the Streaming SIMD Extensions 4.1 (SSE4.1). The processors support several Advanced Technologies: Execute Disable Bit, Intel 64 architecture, and Enhanced Intel SpeedStep® Technology. The Intel Core™2 Duo processor E8600, E8500, E8400, E8300, and E8200 support Intel Trusted Execution Technology (Intel TXT) and Intel Virtualization Technology (Intel VT). The Intel Core™2 Duo processor E7600 supports Intel Virtualization Technology (Intel VT). The processor's front side bus (FSB) use a split-transaction, deferred reply protocol. The FSB uses Source-Synchronous Transfer of address and data to improve performance by transferring data four times per bus clock (4X data transfer rate). Along with the 4X data bus, the address bus can deliver addresses two times per bus clock and is referred to as a "double-clocked" or 2X address bus. Working together, the 4X data bus and 2X address bus provide a data bus bandwidth of up to 10.7 GB/s. Intel has enabled support components for the processor including heatsink, heatsink retention mechanism, and socket. Manufacturability is a high priority; hence, mechanical assembly may be completed from the top of the baseboard and should not require any special tooling. Datasheet 9 Introduction 1.1 Terminology A ‘#’ symbol after a signal name refers to an active low signal, indicating a signal is in the active state when driven to a low level. For example, when RESET# is low, a reset has been requested. Conversely, when NMI is high, a nonmaskable interrupt has occurred. In the case of signals where the name does not imply an active state but describes part of a binary sequence (such as address or data), the ‘#’ symbol implies that the signal is inverted. For example, D[3:0] = ‘HLHL’ refers to a hex ‘A’, and D[3:0]# = ‘LHLH’ also refers to a hex ‘A’ (H= High logic level, L= Low logic level). “Front Side Bus” refers to the interface between the processor and system core logic (a.k.a. the chipset components). The FSB is a multiprocessing interface to processors, memory, and I/O. 1.1.1 Processor Terminology Definitions Commonly used terms are explained here for clarification: • Intel® Core™2 Duo processor E8000 series — Dual core processor in the FCLGA8 package with a 6 MB L2 cache. • Intel® Core™2 Duo processor E7000 series — Dual core processor in the FCLGA8 package with a 3 MB L2 cache. • Processor — For this document, the term processor is the generic form of the Intel® Core™2 Duo processor E8000 series and Intel® Core™2 Duo processor E7000 series. • Voltage Regulator Design Guide — For this document “Voltage Regulator Design Guide” may be used in place of: — Voltage Regulator-Down (VRD) 11.0 Processor Power Delivery Design Guidelines For Desktop LGA775 Socket • Enhanced Intel® Core™ microarchitecture — A new foundation for Intel® architecture-based desktop, mobile and mainstream server multi-core processors. For additional information refer to: http://www.intel.com/technology/architecture/ coremicro/ • Keep-out zone — The area on or near the processor that system design can not use. • Processor core — Processor die with integrated L2 cache. • LGA775 socket — The processors mate with the system board through a surface mount, 775-land, LGA socket. • Integrated heat spreader (IHS) —A component of the processor package used to enhance the thermal performance of the package. Component thermal solutions interface with the processor at the IHS surface. • Retention mechanism (RM) — Since the LGA775 socket does not include any mechanical features for heatsink attach, a retention mechanism is required. Component thermal solutions should attach to the processor using a retention mechanism that is independent of the socket. • FSB (Front Side Bus) — The electrical interface that connects the processor to the chipset. Also referred to as the processor system bus or the system bus. All memory and I/O transactions as well as interrupt messages pass between the processor and chipset over the FSB. 10 Datasheet Introduction • Storage conditions — Refers to a non-operational state. The processor may be installed in a platform, in a tray, or loose. Processors may be sealed in packaging or exposed to free air. Under these conditions, processor lands should not be connected to any supply voltages, have any I/Os biased, or receive any clocks. Upon exposure to “free air”(i.e., unsealed packaging or a device removed from packaging material) the processor must be handled in accordance with moisture sensitivity labeling (MSL) as indicated on the packaging material. • Functional operation — Refers to normal operating conditions in which all processor specifications, including DC, AC, system bus, signal quality, mechanical and thermal are satisfied. • Execute Disable Bit — Execute Disable Bit allows memory to be marked as executable or non-executable, when combined with a supporting operating system. If code attempts to run in non-executable memory the processor raises an error to the operating system. This feature can prevent some classes of viruses or worms that exploit buffer over run vulnerabilities and can thus help improve the overall security of the system. See the Intel® Architecture Software Developer's Manual for more detailed information. • Intel® 64 Architecture— An enhancement to Intel's IA-32 architecture, allowing the processor to execute operating systems and applications written to take advantage of the Intel 64 architecture. Further details on Intel 64 architecture and programming model can be found in the Intel Extended Memory 64 Technology Software Developer Guide at http://developer.intel.com/technology/ 64bitextensions/. • Enhanced Intel SpeedStep® Technology — Enhanced Intel SpeedStep Technology allows trade-offs to be made between performance and power consumptions, based on processor utilization. This may lower average power consumption (in conjunction with OS support). • Intel® Virtualization Technology (Intel® VT) — A set of hardware enhancements to Intel server and client platforms that can improve virtualization solutions. Intel VT will provide a foundation for widely-deployed virtualization solutions and enables more robust hardware assisted virtualization solutions. More information can be found at: http://www.intel.com/technology/virtualization/ • Intel® Trusted Execution Technology (Intel® TXT) — A key element in Intel's safer computing initiative which defines a set of hardware enhancements that interoperate with an Intel TXT enabled OS to help protect against software-based attacks. Intel TXT creates a hardware foundation that builds on Intel's Virtualization Technology (Intel VT) to help protect the confidentiality and integrity of data stored/created on the client PC. • Platform Environment Control Interface (PECI) — A proprietary one-wire bus interface that provides a communication channel between the processor and chipset components to external monitoring devices. Datasheet 11 Introduction 1.2 References Material and concepts available in the following documents may be beneficial when reading this document. Table 1. References Document Location Intel® Core™2 Duo Processor E8000 and E7000 Series Specification Update www.intel.com/design/ processor/specupdt/ 318733.htm Intel® Core™2 Duo Processor E8000 and E7000 Series and Intel® Pentium Dual-Core Processor E6000 and E5000 Series Thermal and Mechanical Design Guidelines www.intel.com/design/ processor/designex/ 318734.htm Voltage Regulator-Down (VRD) 11.0 Processor Power Delivery Design Guidelines For Desktop LGA775 Socket http://www.intel.com/ design/processor/ applnots/313214.htm http://intel.com/design/ Pentium4/guides/ 302666.htm LGA775 Socket Mechanical Design Guide Intel® 64 and IA-32 Intel Architecture Software Developer's Manuals Volume 1: Basic Architecture Volume 2A: Instruction Set Reference, A-M Volume 2B: Instruction Set Reference, N-Z Volume 3A: System Programming Guide, Part 1 http://www.intel.com/ products/processor/ manuals/ Volume 3B: System Programming Guide, Part 2 § 12 Datasheet Electrical Specifications 2 Electrical Specifications This chapter describes the electrical characteristics of the processor interfaces and signals. DC electrical characteristics are provided. 2.1 Power and Ground Lands The processor has VCC (power), VTT, and VSS (ground) inputs for on-chip power distribution. All power lands must be connected to VCC, while all VSS lands must be connected to a system ground plane. The processor VCC lands must be supplied the voltage determined by the Voltage IDentification (VID) lands. The signals denoted as VTT provide termination for the front side bus and power to the I/O buffers. A separate supply must be implemented for these lands, that meets the VTT specifications outlined in Table 4. 2.2 Decoupling Guidelines Due to its large number of transistors and high internal clock speeds, the processor is capable of generating large current swings. This may cause voltages on power planes to sag below their minimum specified values if bulk decoupling is not adequate. Larger bulk storage (CBULK), such as electrolytic or aluminum-polymer capacitors, supply current during longer lasting changes in current demand by the component, such as coming out of an idle condition. Similarly, they act as a storage well for current when entering an idle condition from a running condition. The motherboard must be designed to ensure that the voltage provided to the processor remains within the specifications listed in Table 4. Failure to do so can result in timing violations or reduced lifetime of the component. 2.2.1 VCC Decoupling VCC regulator solutions need to provide sufficient decoupling capacitance to satisfy the processor voltage specifications. This includes bulk capacitance with low effective series resistance (ESR) to keep the voltage rail within specifications during large swings in load current. In addition, ceramic decoupling capacitors are required to filter high frequency content generated by the front side bus and processor activity. Consult the Voltage Regulator-Down (VRD) 11.0 Processor Power Delivery Design Guidelines For Desktop LGA775 Socket for further information. Contact your Intel field representative for additional information. 2.2.2 VTT Decoupling Decoupling must be provided on the motherboard. Decoupling solutions must be sized to meet the expected load. To ensure compliance with the specifications, various factors associated with the power delivery solution must be considered including regulator type, power plane and trace sizing, and component placement. A conservative decoupling solution would consist of a combination of low ESR bulk capacitors and high frequency ceramic capacitors. Datasheet 13 Electrical Specifications 2.2.3 FSB Decoupling The processor integrates signal termination on the die. In addition, some of the high frequency capacitance required for the FSB is included on the processor package. However, additional high frequency capacitance must be added to the motherboard to properly decouple the return currents from the front side bus. Bulk decoupling must also be provided by the motherboard for proper [A]GTL+ bus operation. 2.3 Voltage Identification The Voltage Identification (VID) specification for the processor is defined by the Voltage Regulator-Down (VRD) 11.0 Processor Power Delivery Design Guidelines For Desktop LGA775 Socket. The voltage set by the VID signals is the reference VR output voltage to be delivered to the processor VCC lands (see Chapter 2.6.3 for VCC overshoot specifications). Refer to Table 13 for the DC specifications for these signals. Voltages for each processor frequency is provided in Table 4. Note: To support the Deeper Sleep State the platform must use a VRD 11.1 compliant solution. The Deeper Sleep State also requires additional platform support. Individual processor VID values may be calibrated during manufacturing such that two devices at the same core speed may have different default VID settings. This is reflected by the VID Range values provided in Table 4. Refer to the Intel® Core™2 Duo Processor E8000 and E7000 Series Specification Update for further details on specific valid core frequency and VID values of the processor. Note that this differs from the VID employed by the processor during a power management event (Thermal Monitor 2, Enhanced Intel SpeedStep® technology, or Extended HALT State). The processor uses eight voltage identification signals, VID[7:0], to support automatic selection of power supply voltages. Table 2 specifies the voltage level corresponding to the state of VID[7:0]. A ‘1’ in this table refers to a high voltage level and a ‘0’ refers to a low voltage level. If the processor socket is empty (VID[7:0] = 11111110), or the voltage regulation circuit cannot supply the voltage that is requested, it must disable itself. The processor provides the ability to operate while transitioning to an adjacent VID and its associated processor core voltage (VCC). This will represent a DC shift in the load line. It should be noted that a low-to-high or high-to-low voltage state change may result in as many VID transitions as necessary to reach the target core voltage. Transitions above the specified VID are not permitted. Table 4 includes VID step sizes and DC shift ranges. Minimum and maximum voltages must be maintained as shown in Table 5, Figure 1, Table 6, and Figure 2, as measured across the VCC_SENSE and VSS_SENSE lands. The VRM or VRD utilized must be capable of regulating its output to the value defined by the new VID. DC specifications for dynamic VID transitions are included in Table 4 and Table 5. Refer to the Voltage Regulator Design Guide for further details. 14 Datasheet Electrical Specifications Table 2. Voltage Identification Definition VID VID VID VID VID VID VID VID 7 6 5 4 3 2 1 0 Voltage VID VID VID VID VID VID VID VID Voltage 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 OFF 0 1 0 1 1 1 0 0 0 0 0 0 0 0 1 0 1.6 0 1 0 1 1 1 1 0 1.025 0 0 0 0 0 1 0 0 1.5875 0 1 1 0 0 0 0 0 1.0125 0 0 0 0 0 1 1 0 1.575 0 1 1 0 0 0 1 0 1 0 0 0 0 1 0 0 0 1.5625 0 1 1 0 0 1 0 0 0.9875 0 0 0 0 1 0 1 0 1.55 0 1 1 0 0 1 1 0 0.975 0 0 0 0 1 1 0 0 1.5375 0 1 1 0 1 0 0 0 0.9625 0 0 0 0 1 1 1 0 1.525 0 1 1 0 1 0 1 0 0.95 0 0 0 1 0 0 0 0 1.5125 0 1 1 0 1 1 0 0 0.9375 0 0 0 1 0 0 1 0 1.5 0 1 1 0 1 1 1 0 0.925 0 0 0 1 0 1 0 0 1.4875 0 1 1 1 0 0 0 0 0.9125 0 0 0 1 0 1 1 0 1.475 0 1 1 1 0 0 1 0 0.9 0 0 0 1 1 0 0 0 1.4625 0 1 1 1 0 1 0 0 0.8875 0 0 0 1 1 0 1 0 1.45 0 1 1 1 0 1 1 0 0.875 0 0 0 1 1 1 0 0 1.4375 0 1 1 1 1 0 0 0 0.8625 0 0 0 1 1 1 1 0 1.425 0 1 1 1 1 0 1 0 0.85 0 0 1 0 0 0 0 0 1.4125 0 1 1 1 1 1 0 0 0.8375 0 0 1 0 0 0 1 0 1.4 0 1 1 1 1 1 1 0 0.825 0 0 1 0 0 1 0 0 1.3875 1 0 0 0 0 0 0 0 0.8125 0 0 1 0 0 1 1 0 1.375 1 0 0 0 0 0 1 0 0.8 0 0 1 0 1 0 0 0 1.3625 1 0 0 0 0 1 0 0 0.7875 0 0 1 0 1 0 1 0 1.35 1 0 0 0 0 1 1 0 0.775 0 0 1 0 1 1 0 0 1.3375 1 0 0 0 1 0 0 0 0.7625 0 0 1 0 1 1 1 0 1.325 1 0 0 0 1 0 1 0 0.75 0 0 1 1 0 0 0 0 1.3125 1 0 0 0 1 1 0 0 0.7375 0 0 1 1 0 0 1 0 1.3 1 0 0 0 1 1 1 0 0.725 0 0 1 1 0 1 0 0 1.2875 1 0 0 1 0 0 0 0 0.7125 0 0 1 1 0 1 1 0 1.275 1 0 0 1 0 0 1 0 0.7 0 0 1 1 1 0 0 0 1.2625 1 0 0 1 0 1 0 0 0.6875 0 0 1 1 1 0 1 0 1.25 1 0 0 1 0 1 1 0 0.675 0 0 1 1 1 1 0 0 1.2375 1 0 0 1 1 0 0 0 0.6625 0 0 1 1 1 1 1 0 1.225 1 0 0 1 1 0 1 0 0.65 0 1 0 0 0 0 0 0 1.2125 1 0 0 1 1 1 0 0 0.6375 0 1 0 0 0 0 1 0 1.2 1 0 0 1 1 1 1 0 0.625 0 1 0 0 0 1 0 0 1.1875 1 0 1 0 0 0 0 0 0.6125 0 1 0 0 0 1 1 0 1.175 1 0 1 0 0 0 1 0 0.6 0 1 0 0 1 0 0 0 1.1625 1 0 1 0 0 1 0 0 0.5875 0 1 0 0 1 0 1 0 1.15 1 0 1 0 0 1 1 0 0.575 0 1 0 0 1 1 0 0 1.1375 1 0 1 0 1 0 0 0 0.5625 0 1 0 0 1 1 1 0 1.125 1 0 1 0 1 0 1 0 0.55 0 1 0 1 0 0 0 0 1.1125 1 0 1 0 1 1 0 0 0.5375 0 1 0 1 0 0 1 0 1.1 1 0 1 0 1 1 1 0 0.525 0 1 0 1 0 1 0 0 1.0875 1 0 1 1 0 0 0 0 0.5125 0 1 0 1 0 1 1 0 1.075 1 0 1 1 0 0 1 0 0.5 0 1 0 1 1 0 0 0 1.0625 1 1 1 1 1 1 1 0 OFF 0 1 0 1 1 0 1 0 1.05 Datasheet 1.0375 15 Electrical Specifications 2.4 Reserved, Unused, and TESTHI Signals All RESERVED lands must remain unconnected. Connection of these lands to VCC, VSS, VTT, or to any other signal (including each other) can result in component malfunction or incompatibility with future processors. See Chapter 4 for a land listing of the processor and the location of all RESERVED lands. In a system level design, on-die termination has been included by the processor to allow signals to be terminated within the processor silicon. Most unused GTL+ inputs should be left as no connects as GTL+ termination is provided on the processor silicon. However, see Table 8 for details on GTL+ signals that do not include on-die termination. Unused active high inputs, should be connected through a resistor to ground (VSS). Unused outputs can be left unconnected, however this may interfere with some TAP functions, complicate debug probing, and prevent boundary scan testing. A resistor must be used when tying bidirectional signals to power or ground. When tying any signal to power or ground, a resistor will also allow for system testability. Resistor values should be within ± 20% of the impedance of the motherboard trace for front side bus signals. For unused GTL+ input or I/O signals, use pull-up resistors of the same value as the on-die termination resistors (RTT). For details see Table 15. TAP and CMOS signals do not include on-die termination. Inputs and utilized outputs must be terminated on the motherboard. Unused outputs may be terminated on the motherboard or left unconnected. Note that leaving unused outputs unterminated may interfere with some TAP functions, complicate debug probing, and prevent boundary scan testing. All TESTHI[12,10:0] lands should be individually connected to VTT using a pull-up resistor which matches the nominal trace impedance. The TESTHI signals may use individual pull-up resistors or be grouped together as detailed below. A matched resistor must be used for each group: • TESTHI[1:0] • TESTHI[7:2] • TESTHI8/FC42 – cannot be grouped with other TESTHI signals • TESTHI9/FC43 – cannot be grouped with other TESTHI signals • TESTHI10 – cannot be grouped with other TESTHI signals • TESTHI12/FC44 – cannot be grouped with other TESTHI signals Terminating multiple TESTHI pins together with a single pull-up resistor is not recommended for designs supporting boundary scan for proper Boundary Scan testing of the TESTHI signals. For optimum noise margin, all pull-up resistor values used for TESTHI[12,10:0] lands should have a resistance value within ± 20% of the impedance of the board transmission line traces. For example, if the nominal trace impedance is 50 Ω, then a value between 40 Ω and 60 Ω should be used. 2.5 Power Segment Identifier (PSID) Power Segment Identifier (PSID) is a mechanism to prevent booting under mismatched power requirement situations. The PSID mechanism enables BIOS to detect if the processor in use requires more power than the platform voltage regulator (VR) is capable of supplying. For example, a 130 W TDP processor installed in a board with a 65 W or 95 W TDP capable VR may draw too much power and cause a potential VR issue. 16 Datasheet Electrical Specifications 2.6 Voltage and Current Specification 2.6.1 Absolute Maximum and Minimum Ratings Table 3 specifies absolute maximum and minimum ratings only and lie outside the functional limits of the processor. Within functional operation limits, functionality and long-term reliability can be expected. At conditions outside functional operation condition limits, but within absolute maximum and minimum ratings, neither functionality nor long-term reliability can be expected. If a device is returned to conditions within functional operation limits after having been subjected to conditions outside these limits, but within the absolute maximum and minimum ratings, the device may be functional, but with its lifetime degraded depending on exposure to conditions exceeding the functional operation condition limits. At conditions exceeding absolute maximum and minimum ratings, neither functionality nor long-term reliability can be expected. Moreover, if a device is subjected to these conditions for any length of time then, when returned to conditions within the functional operating condition limits, it will either not function, or its reliability will be severely degraded. Although the processor contains protective circuitry to resist damage from static electric discharge, precautions should always be taken to avoid high static voltages or electric fields. Table 3. Absolute Maximum and Minimum Ratings Symbol Parameter Min Max Unit Notes1, 2 VCC Core voltage with respect to VSS –0.3 1.45 V - VTT FSB termination voltage with respect to VSS –0.3 1.45 V - TCASE Processor case temperature See Section 5 See Section 5 °C - TSTORAGE Processor storage temperature –40 85 °C 3, 4, 5 NOTES: 1. For functional operation, all processor electrical, signal quality, mechanical and thermal specifications must be satisfied. 2. Excessive overshoot or undershoot on any signal will likely result in permanent damage to the processor. 3. Storage temperature is applicable to storage conditions only. In this scenario, the processor must not receive a clock, and no lands can be connected to a voltage bias. Storage within these limits will not affect the long-term reliability of the device. For functional operation, refer to the processor case temperature specifications. 4. This rating applies to the processor and does not include any tray or packaging. 5. Failure to adhere to this specification can affect the long term reliability of the processor. Datasheet 17 Electrical Specifications 2.6.2 DC Voltage and Current Specification Table 4. Voltage and Current Specifications Symbol VID Range Parameter VID Processor Number (6 MB Cache): Core VCC 3.33 GHz E8500 3.16 GHz E8400 3 GHz E8300 2.83 GHz E8200 2.66 GHz E8190 2.66 GHz 3.06 GHz E7500 2.93 GHz E7400 2.80 GHz E7300 2.66 GHz E7200 2.53 GHz VCC_BOOT Default VCC voltage for initial power up VCCPLL PLL VCC ICC VTT_OUT_LEFT and VTT_OUT_RIGHT ICC 18 Unit 0.8500 — 1.3625 V 1 V 3, 4, 5 Refer to Table 5, Figure 1 Refer to Table 6, Figure 2 — 1.10 — V - 5% 1.50 + 5% V ICC for 775_VR_CONFIG_06: E8600 3.33 GHz E8500 3.16 GHz E8400 3 GHz E8300 2.83 GHz 75 E8200 2.66 GHz 75 E8190 2.66 GHz 75 Processor Number (3 MB Cache): VTT Max VCC for 775_VR_CONFIG_06: E7600 Product Number (6 MB Cache): Typ VCC for 775_VR_CONFIG_06: E8600 Processor Number (3 MB Cache): Notes2, 10 Min 75 — — 75 75 A 6 VCC for 775_VR_CONFIG_06: E7600 3.06 GHz E7500 2.93 GHz E7400 2.80 GHz 75 E7300 2.66 GHz 75 E7200 2.53 GHz 75 75 — — 75 FSB termination voltage on Intel 3 series Chipset family boards 1.045 1.1 1.155 (DC + AC specifications) on Intel 4 series Chipset family boards 1.14 1.2 1.26 — — 580 DC Current that may be drawn from VTT_OUT_LEFT and VTT_OUT_RIGHT per land A V 7, 8 mA Datasheet Electrical Specifications Table 4. Voltage and Current Specifications Symbol ITT Parameter ICC for VTT supply before VCC stable ICC for VTT supply after VCC stable Min Typ — — Max 4.5 4.6 Unit A ICC_VCCPLL ICC for PLL land — — 130 mA ICC_GTLREF ICC for GTLREF — — 200 µA Notes2, 10 9 NOTES: 1. Each processor is programmed with a maximum valid voltage identification value (VID), which is set at manufacturing and can not be altered. Individual maximum VID values are calibrated during manufacturing such that two processors at the same frequency may have different settings within the VID range. Note that this differs from the VID employed by the processor during a power management event (Thermal Monitor 2, Enhanced Intel SpeedStep® technology, or Extended HALT State). 2. Unless otherwise noted, all specifications in this table are based on estimates and simulations or empirical data. These specifications will be updated with characterized data from silicon measurements at a later date. 3. These voltages are targets only. A variable voltage source should exist on systems in the event that a different voltage is required. See Section 2.3 and Table 2 for more information. 4. The voltage specification requirements are measured across VCC_SENSE and VSS_SENSE lands at the socket with a 100 MHz bandwidth oscilloscope, 1.5 pF maximum probe capacitance, and 1 MΩ minimum impedance. The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from the system is not coupled into the oscilloscope probe. 5. Refer to Table 5, Figure 1, Table 6, and Figure 2 for the minimum, typical, and maximum VCC allowed for a given current. The processor should not be subjected to any VCC and ICC combination wherein VCC exceeds VCC_MAX for a given current. 6. ICC_MAX specification is based on VCC_MAX loadline. Refer to Figure 1 for details. 7. VTT must be provided using a separate voltage source and not be connected to VCC. This specification is measured at the land. 8. Baseboard bandwidth is limited to 20 MHz. 9. This is the maximum total current drawn from the VTT plane by only the processor. This specification does not include the current coming from on-board termination (RTT), through the signal line. Refer to the Voltage Regulator Design Guide to determine the total ITT drawn by the system. This parameter is based on design characterization and is not tested. 10. Adherence to the voltage specifications for the processor are required to ensure reliable processor operation. Datasheet 19 Electrical Specifications Table 5. Intel® Core™2 Duo Processor E8000 Series VCC Static and Transient Tolerance Voltage Deviation from VID Setting (V)1, 2, 3, 4 ICC (A) Maximum Voltage 1.40 mΩ Typical Voltage 1.48 mΩ Minimum Voltage 1.55 mΩ -0.038 0 0.000 -0.019 5 -0.007 -0.026 -0.046 10 -0.014 -0.034 -0.054 15 -0.021 -0.041 -0.061 20 -0.028 -0.049 -0.069 25 -0.035 -0.056 -0.077 30 -0.042 -0.063 -0.085 35 -0.049 -0.071 -0.092 40 -0.056 -0.078 -0.100 45 -0.063 -0.085 -0.108 50 -0.070 -0.093 -0.116 55 -0.077 -0.100 -0.123 60 -0.084 -0.108 -0.131 65 -0.091 -0.115 -0.139 70 -0.098 -0.122 -0.147 75 -0.105 -0.130 -0.154 NOTES: 1. The loadline specification includes both static and transient limits except for overshoot allowed as shown in Section 2.6.3. 2. This table is intended to aid in reading discrete points on Figure 1. 3. The loadlines specify voltage limits at the die measured at the VCC_SENSE and VSS_SENSE lands. Voltage regulation feedback for voltage regulator circuits must be taken from processor VCC and VSS lands. Refer to the Voltage Regulator Design Guide for socket loadline guidelines and VR implementation details. 4. Adherence to this loadline specification is required to ensure reliable processor operation. 20 Datasheet Electrical Specifications Figure 1. Intel® Core™2 Duo Processor E8000 Series VCC Static and Transient Tolerance Icc [A] 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 VID - 0.000 VID - 0.013 VID - 0.025 Vcc Maximum VID - 0.038 VID - 0.050 Vcc [V] VID - 0.063 VID - 0.075 Vcc Typical VID - 0.088 VID - 0.100 VID - 0.113 Vcc Minimum VID - 0.125 VID - 0.138 VID - 0.150 VID - 0.163 NOTES: 1. The loadline specification includes both static and transient limits except for overshoot allowed as shown in Section 2.6.3. 2. This loadline specification shows the deviation from the VID set point. 3. The loadlines specify voltage limits at the die measured at the VCC_SENSE and VSS_SENSE lands. Voltage regulation feedback for voltage regulator circuits must be taken from processor VCC and VSS lands. Refer to the Voltage Regulator Design Guide for socket loadline guidelines and VR implementation details. Datasheet 21 Electrical Specifications Table 6. Intel® Core™2 Duo Processor E7000 Series VCC Static and Transient Tolerance Voltage Deviation from VID Setting (V)1, 2, 3, 4 ICC (A) Maximum Voltage 1.65 mΩ Typical Voltage 1.73 mΩ Minimum Voltage 1.80 mΩ 0 0.000 -0.019 -0.038 5 -0.008 -0.028 -0.047 10 -0.017 -0.036 -0.056 15 -0.025 -0.045 -0.065 20 -0.033 -0.054 -0.074 25 -0.041 -0.062 -0.083 30 -0.050 -0.071 -0.092 35 -0.058 -0.079 -0.101 40 -0.066 -0.088 -0.110 45 -0.074 -0.097 -0.119 50 -0.083 -0.105 -0.128 55 -0.091 -0.114 -0.137 60 -0.099 -0.123 -0.146 65 -0.107 -0.131 -0.155 70 -0.116 -0.140 -0.164 75 -0.124 -0.148 -0.173 NOTES: 1. 2. 3. 4. 22 The loadline specification includes both static and transient limits except for overshoot allowed as shown in Section 2.6.3. This table is intended to aid in reading discrete points on Figure 1. The loadlines specify voltage limits at the die measured at the VCC_SENSE and VSS_SENSE lands. Voltage regulation feedback for voltage regulator circuits must be taken from processor VCC and VSS lands. Refer to the Voltage Regulator Design Guide for socket loadline guidelines and VR implementation details. Adherence to this loadline specification is required to ensure reliable processor operation. Datasheet Electrical Specifications Figure 2. Intel® Core™2 Duo Processor E7000 Series VCC Static and Transient Tolerance Icc [A] 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 VID - 0.000 VID - 0.013 VID - 0.025 Vcc Maximum VID - 0.038 VID - 0.050 VID - 0.063 Vcc [V] VID - 0.075 VID - 0.088 Vcc Typical VID - 0.100 VID - 0.113 Vcc Minimum VID - 0.125 VID - 0.138 VID - 0.150 VID - 0.163 VID - 0.175 VID - 0.188 NOTES: 1. 2. 3. 2.6.3 The loadline specification includes both static and transient limits except for overshoot allowed as shown in Section 2.6.3. This loadline specification shows the deviation from the VID set point. The loadlines specify voltage limits at the die measured at the VCC_SENSE and VSS_SENSE lands. Voltage regulation feedback for voltage regulator circuits must be taken from processor VCC and VSS lands. Refer to the Voltage Regulator Design Guide for socket loadline guidelines and VR implementation details. VCC Overshoot The processor can tolerate short transient overshoot events where VCC exceeds the VID voltage when transitioning from a high to low current load condition. This overshoot cannot exceed VID + VOS_MAX (VOS_MAX is the maximum allowable overshoot voltage). The time duration of the overshoot event must not exceed TOS_MAX (TOS_MAX is the maximum allowable time duration above VID). These specifications apply to the processor die voltage as measured across the VCC_SENSE and VSS_SENSE lands. Table 7. VCC Overshoot Specifications Symbol Parameter Min Max Unit Figure Notes VOS_MAX Magnitude of VCC overshoot above VID — 50 mV 3 1 TOS_MAX Time duration of VCC overshoot above VID — 25 µs 3 1 NOTES: 1. Adherence to these specifications is required to ensure reliable processor operation. Datasheet 23 Electrical Specifications Figure 3. VCC Overshoot Example Waveform Example Overshoot Waveform VOS Voltage [V] VID + 0.050 VID - 0.000 TOS 0 5 10 15 20 25 Time [us] TOS: Overshoot time above VID VOS: Overshoot above VID NOTES: 1. VOS is measured overshoot voltage. 2. TOS is measured time duration above VID. 2.6.4 Die Voltage Validation Overshoot events on processor must meet the specifications in Table 7 when measured across the VCC_SENSE and VSS_SENSE lands. Overshoot events that are < 10 ns in duration may be ignored. These measurements of processor die level overshoot must be taken with a bandwidth limited oscilloscope set to a greater than or equal to 100 MHz bandwidth limit. 2.7 Signaling Specifications Most processor Front Side Bus signals use Gunning Transceiver Logic (GTL+) signaling technology. This technology provides improved noise margins and reduced ringing through low voltage swings and controlled edge rates. Platforms implement a termination voltage level for GTL+ signals defined as VTT. Because platforms implement separate power planes for each processor (and chipset), separate VCC and VTT supplies are necessary. This configuration allows for improved noise tolerance as processor frequency increases. Speed enhancements to data and address busses have caused signal integrity considerations and platform design methods to become even more critical than with previous processor families. The GTL+ inputs require a reference voltage (GTLREF) which is used by the receivers to determine if a signal is a logical 0 or a logical 1. GTLREF must be generated on the motherboard (see Table 15 for GTLREF specifications). Termination resistors (RTT) for GTL+ signals are provided on the processor silicon and are terminated to VTT. Intel chipsets will also provide on-die termination, thus eliminating the need to terminate the bus on the motherboard for most GTL+ signals. 24 Datasheet Electrical Specifications 2.7.1 FSB Signal Groups The front side bus signals have been combined into groups by buffer type. GTL+ input signals have differential input buffers, which use GTLREF[1:0] as a reference level. In this document, the term “GTL+ Input” refers to the GTL+ input group as well as the GTL+ I/O group when receiving. Similarly, “GTL+ Output” refers to the GTL+ output group as well as the GTL+ I/O group when driving. With the implementation of a source synchronous data bus comes the need to specify two sets of timing parameters. One set is for common clock signals which are dependent upon the rising edge of BCLK0 (ADS#, HIT#, HITM#, etc.) and the second set is for the source synchronous signals which are relative to their respective strobe lines (data and address) as well as the rising edge of BCLK0. Asychronous signals are still present (A20M#, IGNNE#, etc.) and can become active at any time during the clock cycle. Table 8 identifies which signals are common clock, source synchronous, and asynchronous. Table 8. FSB Signal Groups Signal Group Signals1 Type GTL+ Common Clock Input Synchronous to BCLK[1:0] BPRI#, DEFER#, RESET#, RS[2:0]#, TRDY# GTL+ Common Clock I/O Synchronous to BCLK[1:0] ADS#, BNR#, BPM[5:0]#, BR0#3, DBSY#, DRDY#, HIT#, HITM#, LOCK# Signals REQ[4:0]#, A[16:3]# GTL+ Source Synchronous I/O GTL+ Strobes Synchronous to assoc. strobe Synchronous to BCLK[1:0] Associated Strobe 3 A[35:17]#3 ADSTB0# ADSTB1# D[15:0]#, DBI0# DSTBP0#, DSTBN0# D[31:16]#, DBI1# DSTBP1#, DSTBN1# D[47:32]#, DBI2# DSTBP2#, DSTBN2# D[63:48]#, DBI3# DSTBP3#, DSTBN3# ADSTB[1:0]#, DSTBP[3:0]#, DSTBN[3:0]# CMOS A20M#, DPRSTP#. DPSLP#, IGNNE#, INIT#, LINT0/ INTR, LINT1/NMI, SMI#3, STPCLK#, PWRGOOD, SLP#, TCK, TDI, TMS, TRST#, BSEL[2:0], VID[7:0], PSI# Open Drain Output FERR#/PBE#, IERR#, THERMTRIP#, TDO Open Drain Input/ Output PROCHOT#4 FSB Clock Power/Other Clock BCLK[1:0], ITP_CLK[1:0]2 VCC, VTT, VCCA, VCCIOPLL, VCCPLL, VSS, VSSA, GTLREF[1:0], COMP[8,3:0], RESERVED, TESTHI[12,10:0], VCC_SENSE, VCC_MB_REGULATION, VSS_SENSE, VSS_MB_REGULATION, DBR#2, VTT_OUT_LEFT, VTT_OUT_RIGHT, VTT_SEL, FCx, PECI, MSID[1:0] NOTES: 1. Refer to Section 4.2 for signal descriptions. 2. In processor systems where no debug port is implemented on the system board, these signals are used to support a debug port interposer. In systems with the debug port implemented on the system board, these signals are no connects. Datasheet 25 Electrical Specifications 3. 4. The value of these signals during the active-to-inactive edge of RESET# defines the processor configuration options. See Section 6.1 for details. PROCHOT# signal type is open drain output and CMOS input. . Table 9. Signal Characteristics Signals with RTT Signals with No RTT A[35:3]#, ADS#, ADSTB[1:0]#, BNR#, BPRI#, D[63:0]#, DBI[3:0]#, DBSY#, DEFER#, DRDY#, DSTBN[3:0]#, DSTBP[3:0]#, HIT#, HITM#, LOCK#, PROCHOT#, REQ[4:0]#, RS[2:0]#, TRDY# A20M#, BCLK[1:0], BPM[5:0]#, BSEL[2:0], COMP[8,3:0], FERR#/PBE#, IERR#, IGNNE#, INIT#, ITP_CLK[1:0], LINT0/INTR, LINT1/ NMI, MSID[1:0], PWRGOOD, RESET#, SMI#, STPCLK#, TDO, TESTHI[12,10:0], THERMTRIP#, VID[7:0], GTLREF[1:0], TCK, TDI, TMS, TRST#, VTT_SEL Open Drain Signals1 THERMTRIP#, FERR#/PBE#, IERR#, BPM[5:0]#, BR0#, TDO, FCx NOTES: 1. Signals that do not have RTT, nor are actively driven to their high-voltage level. Table 10. Signal Reference Voltages GTLREF BPM[5:0]#, RESET#, BNR#, HIT#, HITM#, BR0#, A[35:0]#, ADS#, ADSTB[1:0]#, BPRI#, D[63:0]#, DBI[3:0]#, DBSY#, DEFER#, DRDY#, DSTBN[3:0]#, DSTBP[3:0]#, LOCK#, REQ[4:0]#, RS[2:0]#, TRDY# VTT/2 A20M#, LINT0/INTR, LINT1/NMI, IGNNE#, INIT#, PROCHOT#, PWRGOOD1, SMI#, STPCLK#, TCK1, TDI1, TMS1, TRST#1 NOTE: 1. See Table 12 for more information. 2.7.2 CMOS and Open Drain Signals Legacy input signals such as A20M#, IGNNE#, INIT#, SMI#, and STPCLK# use CMOS input buffers. All of the CMOS and Open Drain signals are required to be asserted/deasserted for at least eight BCLKs in order for the processor to recognize the proper signal state. See Section 2.7.3 for the DC specifications. See Section 6.2 for additional timing requirements for entering and leaving the low power states. 26 Datasheet Electrical Specifications 2.7.3 Processor DC Specifications The processor DC specifications in this section are defined at the processor core (pads) unless otherwise stated. All specifications apply to all frequencies and cache sizes unless otherwise stated. Table 11. GTL+ Signal Group DC Specifications Symbol Parameter Min Max Unit Notes1 VIL Input Low Voltage -0.10 GTLREF – 0.10 V 2, 5 VIH Input High Voltage GTLREF + 0.10 VTT + 0.10 V 3, 4, 5 VOH Output High Voltage VTT – 0.10 VTT V 4, 5 IOL Output Low Current N/A VTT_MAX / [(RTT_MIN) + (2 * RON_MIN)] A - ILI Input Leakage Current N/A ± 100 µA 6 ILO Output Leakage Current N/A ± 100 µA 7 RON Buffer On Resistance 7.49 9.16 Ω NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. VIL is defined as the voltage range at a receiving agent that will be interpreted as a logical low value. 3. VIH is defined as the voltage range at a receiving agent that will be interpreted as a logical high value. 4. VIH and VOH may experience excursions above VTT. 5. The VTT referred to in these specifications is the instantaneous VTT. 6. Leakage to VSS with land held at VTT. 7. Leakage to VTT with land held at 300 mV. Table 12. Open Drain and TAP Output Signal Group DC Specifications Symbol Parameter Min Max Unit Notes1 VOL Output Low Voltage 0 0.20 V - IOL Output Low Current 16 50 mA 2 ILO Output Leakage Current N/A ± 200 µA 3 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. Measured at VTT * 0.2 V. 3. For Vin between 0 and VOH. Datasheet 27 Electrical Specifications Table 13. CMOS Signal Group DC Specifications Symb ol Parameter Min Max Unit Notes1 VIL Input Low Voltage -0.10 VTT * 0.30 V 3, 6 VIH Input High Voltage VTT * 0.70 VTT + 0.10 V 4, 5, 6 VOL Output Low Voltage -0.10 VTT * 0.10 V 6 VOH Output High Voltage 0.90 * VTT VTT + 0.10 V 2, 5, 6 IOL Output Low Current VTT * 0.10 / 67 VTT * 0.10 / 27 A 6, 7 IOH Output Low Current VTT * 0.10 / 67 VTT * 0.10 / 27 A 6, 7 ILI Input Leakage Current N/A ± 100 µA 8 ILO Output Leakage Current N/A ± 100 µA 9 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. All outputs are open drain. 3. VIL is defined as the voltage range at a receiving agent that will be interpreted as a logical low value. 4. VIH is defined as the voltage range at a receiving agent that will be interpreted as a logical high value. 5. VIH and VOH may experience excursions above VTT. 6. The VTT referred to in these specifications refers to instantaneous VTT. 7. IOL is measured at 0.10 * VTT. IOH is measured at 0.90 * VTT. 8. Leakage to VSS with land held at VTT. 9. Leakage to VTT with land held at 300 mV. 28 Datasheet Electrical Specifications 2.7.3.1 Platform Environment Control Interface (PECI) DC Specifications PECI is an Intel proprietary one-wire interface that provides a communication channel between Intel processors, chipsets, and external thermal monitoring devices. The processor contains Digital Thermal Sensors (DTS) distributed throughout die. These sensors are implemented as analog-to-digital converters calibrated at the factory for reasonable accuracy to provide a digital representation of relative processor temperature. PECI provides an interface to relay the highest DTS temperature within a die to external management devices for thermal/fan speed control. More detailed information may be found in the Platform Environment Control Interface (PECI) Specification. Table 14. PECI DC Electrical Limits Symbol Vin Definition and Conditions Input Voltage Range Vhysteresis Hysteresis Min Max Units -0.15 VTT V 0.1 * VTT — V Vn Negative-edge threshold voltage 0.275 * VTT 0.500 * VTT V Vp Positive-edge threshold voltage 0.550 * VTT 0.725 * VTT V Isource Isink High level output source (VOH = 0.75 * VTT) Low level output sink (VOL = 0.25 * VTT) -6.0 N/A mA 0.5 1.0 mA Notes1 2 Ileak+ High impedance state leakage to VTT N/A 50 µA 3 Ileak- High impedance leakage to GND N/A 10 µA 3 Cbus Bus capacitance per node N/A 10 pF 4 0.1 * VTT — Vp-p Vnoise Signal noise immunity above 300 MHz NOTES: 1. VTT supplies the PECI interface. PECI behavior does not affect VTT min/max specifications. Refer to Table 4 for VTT specifications. 2. The leakage specification applies to powered devices on the PECI bus. 3. The input buffers use a Schmitt-triggered input design for improved noise immunity. 4. One node is counted for each client and one node for the system host. Extended trace lengths might appear as additional nodes. . Datasheet 29 Electrical Specifications 2.7.3.2 GTL+ Front Side Bus Specifications In most cases, termination resistors are not required as these are integrated into the processor silicon. See Table 9 for details on which GTL+ signals do not include on-die termination. Valid high and low levels are determined by the input buffers by comparing with a reference voltage called GTLREF. Table 15 lists the GTLREF specifications. The GTL+ reference voltage (GTLREF) should be generated on the system board using high precision voltage divider circuits. Table 15. GTL+ Bus Voltage Definitions Symbol Parameter Min Typ Max Units Notes1 GTLREF_PU GTLREF pull up on Intel 3 Series Chipset family boards 57.6 * 0.99 57.6 57.6 * 1.01 Ω 2 GTLREF_PD GTLREF pull down on Intel 3 Series Chipset family boards 100 * 0.99 100 100 * 1.01 Ω 2 RTT Termination Resistance 45 50 55 Ω 3 COMP[3:0] COMP Resistance 49.40 49.90 50.40 Ω 4 COMP8 COMP Resistance 24.65 24.90 25.15 Ω 4 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. GTLREF is to be generated from VTT by a voltage divider of 1% resistors. If an Adjustable GTLREF circuit is used on the board (for Quad-Core processors compatibility), the two GTLREF lands connected to the Adjustable GTLREF circuit require the following: GTLREF_PU = 50 Ω, GTLREF_PD = 100 Ω. 3. RTT is the on-die termination resistance measured at VTT/3 of the GTL+ output driver. 4. COMP resistance must be provided on the system board with 1% resistors. COMP[3:0] and COMP8 resistors are to VSS. 30 Datasheet Electrical Specifications 2.8 Clock Specifications 2.8.1 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking BCLK[1:0] directly controls the FSB interface speed as well as the core frequency of the processor. As in previous generation processors, the processor core frequency is a multiple of the BCLK[1:0] frequency. The processor bus ratio multiplier will be set at its default ratio during manufacturing. The processor supports Half Ratios between 7.5 and 13.5, refer to Table 16 for the processor supported ratios. The processor uses a differential clocking implementation. For more information on the processor clocking, contact your Intel field representative. Table 16. Core Frequency to FSB Multiplier Configuration Multiplication of System Core Frequency to FSB Frequency Core Frequency (266 MHz BCLK/1066 MHz FSB) 1/6 Core Frequency (333 MHz BCLK/ 1333 MHz FSB) Notes1, 2 1.60 GHz 2 GHz - 1/7 1.86 GHz 2.33 GHz - 1/7.5 2 GHz 2.50 GHz - 1/8 2.13 GHz 2.66 GHz - 1/8.5 2.26 GHz 2.83 GHz - 1/9 2.40 GHz 3 GHz - 1/9.5 2.53 GHz 3.16 GHz - 1/10 2.66 GHz 3.33 GHz - 1/10.5 2.80 GHz 3.50 GHz - 1/11 2.93 GHz 3.66 GHz - 1/11.5 3.06 GHz 3.83 GHz - 1/12 3.20 GHz 4 GHz - 1/12.5 3.33 GHz 4.16 GHz - 1/13 3.46 GHz 4.33 GHz - 1/13.5 3.60GHz 4.50 GHz - 1/14 3.73 GHz 4.66 GHz - 1/15 4 GHz 5 GHz - NOTES: 1. Individual processors operate only at or below the rated frequency. 2. Listed frequencies are not necessarily committed production frequencies. Datasheet 31 Electrical Specifications 2.8.2 FSB Frequency Select Signals (BSEL[2:0]) The BSEL[2:0] signals are used to select the frequency of the processor input clock (BCLK[1:0]). Table 17 defines the possible combinations of the signals and the frequency associated with each combination. The required frequency is determined by the processor, chipset, and clock synthesizer. All agents must operate at the same frequency. The Intel® Core™2 Duo processor E7000 series operates at a 1333 MHz FSB and 1066 MHz FSB frequency (selected by a 333 MHz BCLK[1:0] or 266 MHz BCLK[1:0] frequency). The Intel® Core™2 Duo processor E8000 series operates at a 1333 MHz FSB frequency (selected by a 333 MHz BCLK[1:0] frequency). Individual processors will only operate at their specified FSB frequency. For more information about these signals, refer to Section 4.2. Table 17. 2.8.3 BSEL[2:0] Frequency Table for BCLK[1:0] BSEL2 BSEL1 BSEL0 FSB Frequency L L L 266 MHz L L H Reserved L H H Reserved L H L Reserved H H L Reserved H H H Reserved H L H Reserved H L L 333 MHz Phase Lock Loop (PLL) and Filter An on-die PLL filter solution will be implemented on the processor. The VCCPLL input is used for the PLL. Refer to Table 4 for DC specifications. 2.8.4 BCLK[1:0] Specifications Table 18. Front Side Bus Differential BCLK Specifications Symbol Parameter Min Typ Max Unit Figure VL Input Low Voltage -0.30 N/A N/A V 4 VH Input High Voltage N/A N/A 1.15 V 4 0.300 N/A 0.550 V 4 2 Range of Crossing Points N/A N/A 0.140 V 4 - VOS Overshoot N/A N/A 1.4 V 4 3 VUS Undershoot -0.300 N/A N/A V 4 3 Differential Output Swing 0.300 N/A N/A V 5 4 VCROSS(abs) ΔVCROSS VSWING Absolute Crossing Point Notes1 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. Crossing voltage is defined as the instantaneous voltage value when the rising edge of BCLK0 equals the falling edge of BCLK1. 3. “Steady state” voltage, not including overshoot or undershoot. 32 Datasheet Electrical Specifications 4. 5. Table 19. Overshoot is defined as the absolute value of the maximum voltage. Undershoot is defined as the absolute value of the minimum voltage. Measurement taken from differential waveform. FSB Differential Clock Specifications (1333 MHz FSB) T# Parameter Notes1 Min Nom Max Unit Figure BCLK[1:0] Frequency 331.633 — 333.367 MHz - T1: BCLK[1:0] Period 2.99970 — 3.01538 ns 4 2 — — 150 ps 4 3 T5: BCLK[1:0] Rise and Fall Slew Rate 2.5 — 8 V/ns 5 4 Slew Rate Matching N/A N/A 20 % T2: BCLK[1:0] Period Stability 6 5 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor core frequencies based on a 333 MHz BCLK[1:0]. 2. The period specified here is the average period. A given period may vary from this specification as governed by the period stability specification (T2). The Min period specification is based on -300 PPM deviation from a 3 ns period. The Max period specification is based on the summation of +300 PPM deviation from a 3 ns period and a +0.5% maximum variance due to spread spectrum clocking. 3. In this context, period stability is defined as the worst case timing difference between successive crossover voltages. In other words, the largest absolute difference between adjacent clock periods must be less than the period stability. 4. Slew rate is measured through the VSWING voltage range centered about differential zero. Measurement taken from differential waveform. 5. Matching applies to rising edge rate for Clock and falling edge rate for Clock#. It is measured using a ±75 mV window centered on the average cross point where Clock rising meets Clock# falling. The median cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. 6. Duty Cycle (High time/Period) must be between 40 and 60% Table 20. FSB Differential Clock Specifications (1066 MHz FSB) T# Parameter Notes1 Min Nom Max Unit Figure BCLK[1:0] Frequency 265.307 — 266.693 MHz - 6 T1: BCLK[1:0] Period 3.74963 — 3.76922 ns 4 2 — — 150 ps 4 3 T5: BCLK[1:0] Rise and Fall Slew Rate 2.5 — 8 V/ns 5 4 Slew Rate Matching N/A N/A 20 % - 5 T2: BCLK[1:0] Period Stability NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor core frequencies based on a 266 MHz BCLK[1:0]. 2. The period specified here is the average period. A given period may vary from this specification as governed by the period stability specification (T2). The Min period specification is based on -300 PPM deviation from a 3.75 ns period. The Max period specification is based on the summation of +300 PPM deviation from a 3.75 ns period and a +0.5% maximum variance due to spread spectrum clocking. 3. In this context, period stability is defined as the worst case timing difference between successive crossover voltages. In other words, the largest absolute difference between adjacent clock periods must be less than the period stability. 4. Slew rate is measured through the VSWING voltage range centered about differential zero. Measurement taken from differential waveform. Datasheet 33 Electrical Specifications 5. 6. Figure 4. Matching applies to rising edge rate for Clock and falling edge rate for Clock#. It is measured using a ±75 mV window centered on the average cross point where Clock rising meets Clock# falling. The median cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. Duty Cycle (High time/Period) must be between 40 and 60% Differential Clock Waveform Tph Overshoot BCLK1 VH Rising Edge Ringback V CROSS (ABS) Threshold Region V CROSS (ABS) Ringback Margin Falling Edge Ringback BCLK0 VL Undershoot Tpl Tp Tp = T1: BCLK[1:0] period T2: BCLK[1:0] period stability (not shown) Tph = T3: BCLK[1:0] pulse high time Tpl = T4: BCLK[1:0] pulse low time T5: BCLK[1:0] rise time through the threshold region T6: BCLK[1:0] fall time through the threshold region Figure 5. Measurement Points for Differential Clock Waveforms Slew_rise Slew _fall +150 mV 0.0V +150mV V_swing -150 mV 0.0V -150mV Diff T5 = BCLK[1:0] rise and fall time through the swing region §§ 34 Datasheet Package Mechanical Specifications 3 Package Mechanical Specifications The processor is packaged in a Flip-Chip Land Grid Array (FC-LGA8) package that interfaces with the motherboard using an LGA775 socket. The package consists of a processor core mounted on a substrate land-carrier. An integrated heat spreader (IHS) is attached to the package substrate and core and serves as the mating surface for processor component thermal solutions, such as a heatsink. Figure 6 shows a sketch of the processor package components and how they are assembled together. Refer to the LGA775 Socket Mechanical Design Guide for complete details on the LGA775 socket. The package components shown in Figure 6 include the following: • • • • • Figure 6. Integrated Heat Spreader (IHS) Thermal Interface Material (TIM) Processor core (die) Package substrate Capacitors Processor Package Assembly Sketch Core (die) TIM IHS Substrate Capacitors LGA775 Socket System Board Processor_Pkg_Assembly_775 NOTE: 1. Socket and motherboard are included for reference and are not part of processor package. 3.1 Package Mechanical Drawing The package mechanical drawings are shown in Figure 7 and Figure 8. The drawings include dimensions necessary to design a thermal solution for the processor. These dimensions include: • • • • • • • Datasheet Package reference with tolerances (total height, length, width, etc.) IHS parallelism and tilt Land dimensions Top-side and back-side component keep-out dimensions Reference datums All drawing dimensions are in mm [in]. Guidelines on potential IHS flatness variation with socket load plate actuation and installation of the cooling solution is available in the processor Thermal and Mechanical Design Guidelines. 35 Package Mechanical Specifications Figure 7. 36 Processor Package Drawing Sheet 1 of 3 Datasheet Package Mechanical Specifications Figure 8. Datasheet Processor Package Drawing Sheet 2 of 3 37 Package Mechanical Specifications Figure 9. 38 Processor Package Drawing Sheet 3 of 3 Datasheet Package Mechanical Specifications 3.2 Processor Component Keep-Out Zones The processor may contain components on the substrate that define component keepout zone requirements. A thermal and mechanical solution design must not intrude into the required keep-out zones. Decoupling capacitors are typically mounted to either the topside or land-side of the package substrate. See Figure 7 and Figure 8 for keep-out zones. The location and quantity of package capacitors may change due to manufacturing efficiencies but will remain within the component keep-in. 3.3 Package Loading Specifications Table 21 provides dynamic and static load specifications for the processor package. These mechanical maximum load limits should not be exceeded during heatsink assembly, shipping conditions, or standard use condition. Also, any mechanical system or component testing should not exceed the maximum limits. The processor package substrate should not be used as a mechanical reference or load-bearing surface for thermal and mechanical solution. The minimum loading specification must be maintained by any thermal and mechanical solutions. . Table 21. Processor Loading Specifications Parameter Minimum Maximum Notes Static 80 N [17 lbf] 311 N [70 lbf] 1, 2, 3 Dynamic - 756 N [170 lbf] 1, 3, 4 NOTES: 1. These specifications apply to uniform compressive loading in a direction normal to the processor IHS. 2. This is the maximum force that can be applied by a heatsink retention clip. The clip must also provide the minimum specified load on the processor package. 3. These specifications are based on limited testing for design characterization. Loading limits are for the package only and do not include the limits of the processor socket. 4. Dynamic loading is defined as an 11 ms duration average load superimposed on the static load requirement. 3.4 Package Handling Guidelines Table 22 includes a list of guidelines on package handling in terms of recommended maximum loading on the processor IHS relative to a fixed substrate. These package handling loads may be experienced during heatsink removal. Table 22. Package Handling Guidelines Parameter Maximum Recommended Notes Shear 311 N [70 lbf] 1, 4 Tensile 111 N [25 lbf] 2, 4 Torque 3.95 N-m [35 lbf-in] 3, 4 NOTES: 1. A shear load is defined as a load applied to the IHS in a direction parallel to the IHS top surface. 2. A tensile load is defined as a pulling load applied to the IHS in a direction normal to the IHS surface. 3. A torque load is defined as a twisting load applied to the IHS in an axis of rotation normal to the IHS top surface. 4. These guidelines are based on limited testing for design characterization. Datasheet 39 Package Mechanical Specifications 3.5 Package Insertion Specifications The processor can be inserted into and removed from a LGA775 socket 15 times. The socket should meet the LGA775 requirements detailed in the LGA775 Socket Mechanical Design Guide. 3.6 Processor Mass Specification The typical mass of the processor is 21.5 g [0.76 oz]. This mass [weight] includes all the components that are included in the package. 3.7 Processor Materials Table 23 lists some of the package components and associated materials. Table 23. 3.8 Processor Materials Component Material Integrated Heat Spreader (IHS) Nickel Plated Copper Substrate Fiber Reinforced Resin Substrate Lands Gold Plated Copper Processor Markings Figure 10 shows the top-side markings on the processor. This diagram is to aid in the identification of the processor. Figure 10. Processor Top-Side Markings Example INTEL M ©'06 E8500 Intel® Core®2 Duo SLxxx [COO] 3.16GHZ/6M/1333/06 [FPO] e4 ATPO S/N 40 Datasheet Package Mechanical Specifications 3.9 Processor Land Coordinates Figure 11 shows the top view of the processor land coordinates. The coordinates are referred to throughout the document to identify processor lands. . Figure 11. Processor Land Coordinates and Quadrants, Top View VCC / VSS 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 AN AM AL AK AJ AH AG AF AE AD AC AB AA Y W V U T R P N M L K J H G F E D C B A 8 7 6 5 4 3 2 1 AN AM AL AK AJ AH AG AF AE AD AC AB AA Y W V U T R P N M L K J H G F E D C B A Socket 775 Quadrants Top View 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 VTT / Clocks 8 7 6 5 4 3 2 Address/ Common Clock/ Async 1 Data § Datasheet 41 Package Mechanical Specifications 42 Datasheet Land Listing and Signal Descriptions 4 Land Listing and Signal Descriptions This chapter provides the processor land assignment and signal descriptions. 4.1 Processor Land Assignments This section contains the land listings for the processor. The land-out footprint is shown in Figure 12 and Figure 13. These figures represent the land-out arranged by land number and they show the physical location of each signal on the package land array (top view). Table 24 lists the processor lands ordered alphabetically by land (signal) name. Table 25 lists the processor lands ordered numerically by land number. Datasheet 43 Land Listing and Signal Descriptions Figure 12. land-out Diagram (Top View – Left Side) 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC VCC VSS VSS VCC VCC VSS VSS VCC VCC VSS VCC VCC VSS VSS VCC AM VCC VCC VSS VSS VCC VCC VSS VSS VCC VCC VSS VCC VCC VSS VSS VCC AL VCC VCC VSS VSS VCC VCC VSS VSS VCC VCC VSS VCC VCC VSS VSS VCC AK VSS VSS VSS VSS VCC VCC VSS VSS VCC VCC VSS VCC VCC VSS VSS VCC AJ VSS VSS VSS VSS VCC VCC VSS VSS VCC VCC VSS VCC VCC VSS VSS VCC AH VCC VCC VCC VCC VCC VCC VSS VSS VCC VCC VSS VCC VCC VSS VSS VCC AG VCC VCC VCC VCC VCC VCC VSS VSS VCC VCC VSS VCC VCC VSS VSS VCC AF VSS VSS VSS VSS VSS VSS VSS VSS VCC VCC VSS VCC VCC VSS VSS VCC AE VSS VSS VSS VSS VSS VSS VSS VCC VCC VCC VSS VCC VCC VSS VSS VCC AD VCC VCC VCC VCC VCC VCC VCC VCC AN AC VCC VCC VCC VCC VCC VCC VCC VCC AB VSS VSS VSS VSS VSS VSS VSS VSS AA VSS VSS VSS VSS VSS VSS VSS VSS Y VCC VCC VCC VCC VCC VCC VCC VCC W VCC VCC VCC VCC VCC VCC VCC VCC V VSS VSS VSS VSS VSS VSS VSS VSS U VCC VCC VCC VCC VCC VCC VCC VCC T VCC VCC VCC VCC VCC VCC VCC VCC R VSS VSS VSS VSS VSS VSS VSS VSS P VSS VSS VSS VSS VSS VSS VSS VSS N VCC VCC VCC VCC VCC VCC VCC VCC M VCC VCC VCC VCC VCC VCC VCC VCC L VSS VSS VSS VSS VSS VSS VSS VSS K VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC FC34 FC31 VCC BSEL1 FC15 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS FC33 FC32 BSEL2 J H G BSEL0 BCLK1 F RSVD BCLK0 VTT_SEL TESTHI0 TESTHI2 TESTHI7 E FC26 VSS VSS VSS VSS VTT VTT VTT VTT VTT D VTT TESTHI4 TESTHI5 TESTHI3 TESTHI6 RESET# D47# D44# D35# D36# D32# D31# RSVD VSS D43# DSTBN2# DSTBP2# D41# VSS D38# D37# VSS D30# FC10 RSVD D45# D42# VSS D40# D39# VSS D34# D33# VSS VCCPLL D46# VSS D48# DBI2# VSS D49# RSVD VSS VSS VCCIO PLL VSS D58# DBI3# VSS D54# DSTBP3# VSS D51# C VTT VTT VTT VTT VTT VTT B VTT VTT VTT VTT VTT VTT VSS VSSA D63# D59# VSS D60# D57# VSS D55# D53# A VTT VTT VTT VTT VTT VTT FC23 VCCA D62# VSS RSVD D61# VSS D56# DSTBN3# VSS 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 44 Datasheet Land Listing and Signal Descriptions Figure 13. 14 13 land-out Diagram (Top View – Right Side) 12 11 10 9 8 7 6 5 VID_SEL VSS_MB_RE VCC_MB_ ECT GULATION REGULATION 4 3 2 1 VSS_ SENSE VCC_ SENSE VSS VSS AN VCC VSS VCC VCC VSS VCC VCC VCC VSS VCC VCC VSS VCC VCC VID7 FC40 VID6 VSS VID2 VID0 VSS AM VCC VSS VCC VCC VSS VCC VCC VSS VID3 VID1 VID5 VRDSEL PROCHOT# FC25 AL VCC VSS VCC VCC VSS VCC VCC VSS FC8 VSS VID4 ITP_CLK0 VSS FC24 AK VCC VSS VCC VCC VSS VCC VCC VSS A35# A34# VSS ITP_CLK1 BPM0# BPM1# AJ VCC VSS VCC VCC VSS VCC VCC VSS VSS A33# A32# VSS RSVD VSS AH VCC VSS VCC VCC VSS VCC VCC VSS A29# A31# A30# BPM5# BPM3# TRST# AG VCC VSS VCC VCC VSS VCC VCC VSS VSS A27# A28# VSS BPM4# TDO AF VCC VSS VCC VCC VSS VCC SKTOCC# VSS RSVD VSS RSVD FC18 VSS TCK AE VCC VSS A22# ADSTB1# VSS FC36 BPM2# TDI AD VCC VSS VSS A25# RSVD VSS DBR# TMS AC VCC VSS A17# A24# A26# FC37 IERR# VSS AB VCC VSS VSS A23# A21# VSS FC39 VTT_OUT_ RIGHT AA VCC VSS A19# VSS A20# PSII# VSS VCC VSS A18# A16# VSS TESTHI1 TESTHI12/ FC44 MSID0 W VCC VSS VSS A14# A15# VSS RSVD MSID1 V VCC VSS A10# A12# A13# FC30 FC29 FC28 U VCC VSS VSS A9# A11# VSS DPRSTP# COMP1 T VCC VSS ADSTB0# VSS A8# FERR#/ PBE# VSS COMP3 R VCC VSS A4# RSVD VSS INIT# SMI# DPSLP# P VCC VSS VSS RSVD RSVD VSS IGNNE# PWRGOOD N VCC VSS REQ2# A5# A7# VCC VSS VSS A3# A6# VSS SLP# VCC VSS REQ3# VSS REQ0# A20M# FC0/ Y BOOTSELECT VSS M LINT1 L VSS LINT0 K J STPCLK# THERMTRIP# VCC VCC VCC VCC VCC VCC VCC VSS REQ4# REQ1# VSS FC22 FC3 VTT_OUT_ LEFT VSS VSS VSS VSS VSS VSS VSS VSS VSS TESTHI10 FC35 VSS GTLREF1 GTLREF0 D29# D27# DSTBN1# DBI1# FC38 D16# BPRI# DEFER# RSVD PECI TESTHI9/ FC43 TESTHI8/ FC42 COMP2 FC27 G F D28# VSS D24# D23# VSS D18# D17# VSS FC21 RS1# VSS BR0# FC5 VSS D26# DSTBP1# VSS D21# D19# VSS RSVD RSVD FC20 HITM# TRDY# VSS RSVD D25# VSS D15# D22# VSS D12# D20# VSS VSS HIT# VSS ADS# RSVD D52# VSS D14# D11# VSS FC41 DSTBN0# VSS D3# D1# VSS LOCK# BNR# DRDY# VSS VSS COMP8 D13# VSS D10# DSTBP0# VSS D6# D5# VSS D0# RS0# DBSY# D50# COMP0 VSS D9# D8# VSS DBI0# D7# VSS D4# D2# RS2# VSS 14 13 12 11 10 9 8 7 6 5 4 3 2 Datasheet H E D C B A 1 45 Land Listing and Signal Descriptions Table 24. Land Name 46 Alphabetical Land Assignments Land Signal Buffer # Type Table 24. Direction Land Name Alphabetical Land Assignments Land Signal Buffer # Type Direction A3# L5 Source Synch Input/Output BNR# C2 Common Clock Input/Output A4# P6 Source Synch Input/Output BPM0# AJ2 Common Clock Input/Output A5# M5 Source Synch Input/Output BPM1# AJ1 Common Clock Input/Output A6# L4 Source Synch Input/Output BPM2# AD2 Common Clock Input/Output A7# M4 Source Synch Input/Output BPM3# AG2 Common Clock Input/Output A8# R4 Source Synch Input/Output BPM4# AF2 Common Clock Input/Output A9# T5 Source Synch Input/Output BPM5# AG3 Common Clock Input/Output A10# U6 Source Synch Input/Output BPRI# G8 Common Clock A11# T4 Source Synch Input/Output BR0# F3 Common Clock Input/Output A12# U5 Source Synch Input/Output BSEL0 G29 A13# U4 Source Synch Input/Output BSEL1 H30 Asynch CMOS Output A14# V5 Source Synch Input/Output BSEL2 G30 Asynch CMOS Output A15# V4 Source Synch Input/Output COMP0 A13 Power/Other Input A16# W5 Source Synch Input/Output COMP1 T1 Power/Other Input A17# AB6 Source Synch Input/Output COMP2 G2 Power/Other Input A18# W6 Source Synch Input/Output COMP3 R1 Power/Other Input A19# Y6 Source Synch Input/Output COMP8 B13 Power/Other Input A20# Y4 Source Synch Input/Output D0# B4 Source Synch Input/Output A21# AA4 Source Synch Input/Output D1# C5 Source Synch Input/Output A22# AD6 Source Synch Input/Output D2# A4 Source Synch Input/Output A23# AA5 Source Synch Input/Output D3# C6 Source Synch Input/Output A24# AB5 Source Synch Input/Output D4# A5 Source Synch Input/Output A25# AC5 Source Synch Input/Output D5# B6 Source Synch Input/Output A26# AB4 Source Synch Input/Output D6# B7 Source Synch Input/Output A27# AF5 Source Synch Input/Output D7# A7 Source Synch Input/Output A28# AF4 Source Synch Input/Output D8# A10 Source Synch Input/Output A29# AG6 Source Synch Input/Output D9# A11 Source Synch Input/Output A30# AG4 Source Synch Input/Output D10# B10 Source Synch Input/Output A31# AG5 Source Synch Input/Output D11# C11 Source Synch Input/Output A32# AH4 Source Synch Input/Output D12# D8 Source Synch Input/Output A33# AH5 Source Synch Input/Output D13# B12 Source Synch Input/Output A34# AJ5 Source Synch Input/Output D14# C12 Source Synch Input/Output Asynch CMOS Input Output A35# AJ6 Source Synch Input/Output D15# D11 Source Synch Input/Output A20M# K3 Asynch CMOS Input D16# G9 Source Synch Input/Output Common Clock Input/Output ADS# D2 D17# F8 Source Synch Input/Output ADSTB0# R6 Source Synch Input/Output D18# F9 Source Synch Input/Output ADSTB1# AD5 Source Synch Input/Output D19# E9 Source Synch Input/Output BCLK0 F28 Clock Input D20# D7 Source Synch Input/Output BCLK1 G28 Clock Input D21# E10 Source Synch Input/Output Datasheet Land Listing and Signal Descriptions Table 24. Land Name Datasheet Alphabetical Land Assignments Land Signal Buffer # Type Table 24. Direction Land Name Alphabetical Land Assignments Land Signal Buffer # Type Direction D22# D10 Source Synch Input/Output D61# A19 Source Synch Input/Output D23# F11 Source Synch Input/Output D62# A22 Source Synch Input/Output D24# F12 Source Synch Input/Output D63# B22 Source Synch Input/Output D25# D13 Source Synch Input/Output DBI0# A8 Source Synch Input/Output D26# E13 Source Synch Input/Output DBI1# G11 Source Synch Input/Output D27# G13 Source Synch Input/Output DBI2# D19 Source Synch Input/Output D28# F14 Source Synch Input/Output DBI3# C20 Source Synch Input/Output D29# G14 Source Synch Input/Output DBR# AC2 Power/Other Output D30# F15 Source Synch Input/Output DBSY# B2 Common Clock Input/Output D31# G15 Source Synch Input/Output DEFER# G7 Common Clock Input D32# G16 Source Synch Input/Output DPRSTP# T2 Asynch CMOS Input D33# E15 Source Synch Input/Output DPSLP# P1 Asynch CMOS Input D34# E16 Source Synch Input/Output DRDY# C1 D35# G18 Source Synch Input/Output DSTBN0# C8 Source Synch Input/Output D36# G17 Source Synch Input/Output DSTBN1# G12 Source Synch Input/Output D37# F17 Source Synch Input/Output DSTBN2# G20 Source Synch Input/Output D38# F18 Source Synch Input/Output DSTBN3# A16 Source Synch Input/Output D39# E18 Source Synch Input/Output DSTBP0# B9 Source Synch Input/Output D40# E19 Source Synch Input/Output DSTBP1# E12 Source Synch Input/Output Common Clock Input/Output D41# F20 Source Synch Input/Output DSTBP2# G19 Source Synch Input/Output D42# E21 Source Synch Input/Output DSTBP3# C17 Source Synch Input/Output D43# F21 Source Synch Input/Output Power/Other G21 Source Synch Input/Output FC0/ BOOTSELECT Y1 D44# D45# E22 Source Synch Input/Output FC3 J2 Power/Other D46# D22 Source Synch Input/Output D47# G22 Source Synch Input/Output D48# D20 Source Synch Input/Output D49# D17 Source Synch Input/Output D50# A14 Source Synch Input/Output D51# C15 Source Synch Input/Output D52# C14 Source Synch Input/Output D53# B15 Source Synch Input/Output D54# C18 Source Synch Input/Output D55# B16 Source Synch Input/Output D56# A17 Source Synch Input/Output D57# B18 Source Synch Input/Output D58# C21 Source Synch Input/Output D59# B21 Source Synch Input/Output D60# B19 Source Synch Input/Output FC5 F2 Power/Other FC8 AK6 Power/Other FC10 E24 Power/Other FC15 H29 Power/Other FC18 AE3 Power/Other FC20 E5 Power/Other FC21 F6 Power/Other FC22 J3 Power/Other FC23 A24 Power/Other FC24 AK1 Power/Other FC25 AL1 Power/Other FC26 E29 Power/Other FC27 G1 Power/Other FC28 U1 Power/Other FC29 U2 Power/Other FC30 U3 Power/Other 47 Land Listing and Signal Descriptions Table 24. Land Name 48 Alphabetical Land Assignments Land Signal Buffer # Type Table 24. Direction Land Name Alphabetical Land Assignments Land Signal Buffer # Type FC31 J16 Power/Other RESERVED AE6 FC32 H15 Power/Other RESERVED AH2 FC33 H16 Power/Other RESERVED D1 FC34 J17 Power/Other RESERVED D14 FC35 H4 Power/Other RESERVED D16 FC36 AD3 Power/Other RESERVED E23 FC37 AB3 Power/Other RESERVED E6 FC38 G10 Power/Other RESERVED E7 FC39 AA2 Power/Other RESERVED F23 FC40 AM6 Power/Other RESERVED F29 FC41 C9 Power/Other RESERVED G6 FERR#/PBE# R3 Asynch CMOS Output RESERVED N4 GTLREF0 H1 Power/Other Input RESERVED N5 GTLREF1 H2 Power/Other Input RESERVED P5 Direction HIT# D4 Common Clock Input/Output RESET# G23 Common Clock Input HITM# E4 Common Clock Input/Output RS0# B3 Common Clock Input IERR# AB2 Asynch CMOS Output RS1# F5 Common Clock Input IGNNE# N2 Asynch CMOS Input RS2# A3 Common Clock Input INIT# P3 Asynch CMOS Input SKTOCC# AE8 Power/Other Output ITP_CLK0 AK3 TAP Input SLP# L2 Asynch CMOS Input ITP_CLK1 AJ3 TAP Input SMI# P2 Asynch CMOS Input LINT0 K1 Asynch CMOS Input STPCLK# M3 Asynch CMOS Input Input TCK AE1 TAP Input TDI AD1 TAP Input LINT1 L1 Asynch CMOS LOCK# C3 Common Clock Input/Output MSID0 W1 Power/Other Output TDO AF1 TAP Output MSID1 V1 Power/Other Output TESTHI0 F26 Power/Other Input Power/Other Input/Output PECI G5 PROCHOT# AL2 TESTHI1 W3 Power/Other Input Asynch CMOS Input/Output TESTHI10 H5 Power/Other Input TESTHI12/ FC44 W2 Power/Other Input TESTHI2 F25 Power/Other Input TESTHI3 G25 Power/Other Input TESTHI4 G27 Power/Other Input TESTHI5 G26 Power/Other Input TESTHI6 G24 Power/Other Input TESTHI7 F24 Power/Other Input TESTHI8/FC42 G3 Power/Other Input PSI# Y3 Asynch CMOS Output PWRGOOD N1 Power/Other Input REQ0# K4 Source Synch Input/Output REQ1# J5 Source Synch Input/Output REQ2# M6 Source Synch Input/Output REQ3# K6 Source Synch Input/Output REQ4# J6 Source Synch Input/Output RESERVED V2 RESERVED A20 RESERVED AC4 RESERVED AE4 TESTHI9/FC43 G4 Power/Other Input THERMTRIP# M2 Asynch CMOS Output TMS AC1 TAP Input Datasheet Land Listing and Signal Descriptions Table 24. Land Name Datasheet Alphabetical Land Assignments Land Signal Buffer # Type Table 24. Alphabetical Land Assignments Land Signal Buffer # Type Direction Land Name Common Clock Input VCC AF22 Power/Other Input TRDY# E3 TRST# AG1 TAP VCC AF8 Power/Other VCC AA8 Power/Other VCC AF9 Power/Other VCC AB8 Power/Other VCC AG11 Power/Other VCC AC23 Power/Other VCC AG12 Power/Other VCC AC24 Power/Other VCC AG14 Power/Other VCC AC25 Power/Other VCC AG15 Power/Other VCC AC26 Power/Other VCC AG18 Power/Other VCC AC27 Power/Other VCC AG19 Power/Other VCC AC28 Power/Other VCC AG21 Power/Other VCC AC29 Power/Other VCC AG22 Power/Other VCC AC30 Power/Other VCC AG25 Power/Other VCC AC8 Power/Other VCC AG26 Power/Other VCC AD23 Power/Other VCC AG27 Power/Other VCC AD24 Power/Other VCC AG28 Power/Other VCC AD25 Power/Other VCC AG29 Power/Other VCC AD26 Power/Other VCC AG30 Power/Other VCC AD27 Power/Other VCC AG8 Power/Other VCC AD28 Power/Other VCC AG9 Power/Other VCC AD29 Power/Other VCC AH11 Power/Other VCC AD30 Power/Other VCC AH12 Power/Other VCC AD8 Power/Other VCC AH14 Power/Other VCC AE11 Power/Other VCC AH15 Power/Other VCC AE12 Power/Other VCC AH18 Power/Other VCC AE14 Power/Other VCC AH19 Power/Other VCC AE15 Power/Other VCC AH21 Power/Other VCC AE18 Power/Other VCC AH22 Power/Other VCC AE19 Power/Other VCC AH25 Power/Other VCC AE21 Power/Other VCC AH26 Power/Other VCC AE22 Power/Other VCC AH27 Power/Other VCC AE23 Power/Other VCC AH28 Power/Other VCC AE9 Power/Other VCC AH29 Power/Other VCC AF11 Power/Other VCC AH30 Power/Other VCC AF12 Power/Other VCC AH8 Power/Other VCC AF14 Power/Other VCC AH9 Power/Other VCC AF15 Power/Other VCC AJ11 Power/Other VCC AF18 Power/Other VCC AJ12 Power/Other VCC AF19 Power/Other VCC AJ14 Power/Other VCC AF21 Power/Other VCC AJ15 Power/Other Direction 49 Land Listing and Signal Descriptions Table 24. Land Name 50 Alphabetical Land Assignments Land Signal Buffer # Type Direction Table 24. Land Name Alphabetical Land Assignments Land Signal Buffer # Type VCC AJ18 Power/Other VCC AM19 Power/Other VCC AJ19 Power/Other VCC AM21 Power/Other VCC AJ21 Power/Other VCC AM22 Power/Other VCC AJ22 Power/Other VCC AM25 Power/Other VCC AJ25 Power/Other VCC AM26 Power/Other VCC AJ26 Power/Other VCC AM29 Power/Other VCC AJ8 Power/Other VCC AM30 Power/Other VCC AJ9 Power/Other VCC AM8 Power/Other VCC AK11 Power/Other VCC AM9 Power/Other VCC AK12 Power/Other VCC AN11 Power/Other VCC AK14 Power/Other VCC AN12 Power/Other VCC AK15 Power/Other VCC AN14 Power/Other VCC AK18 Power/Other VCC AN15 Power/Other VCC AK19 Power/Other VCC AN18 Power/Other VCC AK21 Power/Other VCC AN19 Power/Other VCC AK22 Power/Other VCC AN21 Power/Other VCC AK25 Power/Other VCC AN22 Power/Other VCC AK26 Power/Other VCC AN25 Power/Other VCC AK8 Power/Other VCC AN26 Power/Other VCC AK9 Power/Other VCC AN29 Power/Other VCC AL11 Power/Other VCC AN30 Power/Other VCC AL12 Power/Other VCC AN8 Power/Other VCC AL14 Power/Other VCC AN9 Power/Other VCC AL15 Power/Other VCC J10 Power/Other VCC AL18 Power/Other VCC J11 Power/Other VCC AL19 Power/Other VCC J12 Power/Other VCC AL21 Power/Other VCC J13 Power/Other VCC AL22 Power/Other VCC J14 Power/Other VCC AL25 Power/Other VCC J15 Power/Other VCC AL26 Power/Other VCC J18 Power/Other VCC AL29 Power/Other VCC J19 Power/Other VCC AL30 Power/Other VCC J20 Power/Other VCC AL8 Power/Other VCC J21 Power/Other VCC AL9 Power/Other VCC J22 Power/Other VCC AM11 Power/Other VCC J23 Power/Other VCC AM12 Power/Other VCC J24 Power/Other VCC AM14 Power/Other VCC J25 Power/Other VCC AM15 Power/Other VCC J26 Power/Other VCC AM18 Power/Other VCC J27 Power/Other Direction Datasheet Land Listing and Signal Descriptions Table 24. Land Name Datasheet Alphabetical Land Assignments Land Signal Buffer # Type Direction Table 24. Land Name Alphabetical Land Assignments Land Signal Buffer # Type Direction VCC J28 Power/Other VCC T27 Power/Other VCC J29 Power/Other VCC T28 Power/Other VCC J30 Power/Other VCC T29 Power/Other VCC J8 Power/Other VCC T30 Power/Other VCC J9 Power/Other VCC T8 Power/Other VCC K23 Power/Other VCC U23 Power/Other VCC K24 Power/Other VCC U24 Power/Other VCC K25 Power/Other VCC U25 Power/Other VCC K26 Power/Other VCC U26 Power/Other VCC K27 Power/Other VCC U27 Power/Other VCC K28 Power/Other VCC U28 Power/Other VCC K29 Power/Other VCC U29 Power/Other VCC K30 Power/Other VCC U30 Power/Other VCC K8 Power/Other VCC U8 Power/Other VCC L8 Power/Other VCC V8 Power/Other VCC M23 Power/Other VCC W23 Power/Other VCC M24 Power/Other VCC W24 Power/Other VCC M25 Power/Other VCC W25 Power/Other VCC M26 Power/Other VCC W26 Power/Other VCC M27 Power/Other VCC W27 Power/Other VCC M28 Power/Other VCC W28 Power/Other VCC M29 Power/Other VCC W29 Power/Other VCC M30 Power/Other VCC W30 Power/Other VCC M8 Power/Other VCC W8 Power/Other VCC N23 Power/Other VCC Y23 Power/Other VCC N24 Power/Other VCC Y24 Power/Other VCC N25 Power/Other VCC Y25 Power/Other VCC N26 Power/Other VCC Y26 Power/Other VCC N27 Power/Other VCC Y27 Power/Other VCC N28 Power/Other VCC Y28 Power/Other VCC N29 Power/Other VCC Y29 Power/Other VCC N30 Power/Other VCC Y30 Power/Other VCC N8 Power/Other VCC Y8 Power/Other VCC_MB_ REGULATION AN5 Power/Other Output VCC_SENSE AN3 Power/Other Output VCC P8 Power/Other VCC R8 Power/Other VCC T23 Power/Other VCC T24 Power/Other VCC T25 Power/Other VCC T26 Power/Other VCCA A23 Power/Other VCCIOPLL C23 Power/Other VCCPLL D23 Power/Other VID_SELECT AN7 Power/Other Output 51 Land Listing and Signal Descriptions Table 24. Land Name 52 Alphabetical Land Assignments Land Signal Buffer # Type Table 24. Direction Land Name Alphabetical Land Assignments Land Signal Buffer # Type VID0 AM2 Asynch CMOS Output VSS AB26 Power/Other VID1 AL5 Asynch CMOS Output VSS AB27 Power/Other VID2 AM3 Asynch CMOS Output VSS AB28 Power/Other VID3 AL6 Asynch CMOS Output VSS AB29 Power/Other VID4 AK4 Asynch CMOS Output VSS AB30 Power/Other VID5 AL4 Asynch CMOS Output VSS AB7 Power/Other VID6 AM5 Asynch CMOS Output VSS AC3 Power/Other VID7 AM7 Asynch CMOS Output VSS AC6 Power/Other VRDSEL AL3 Power/Other VSS AC7 Power/Other VSS B1 Power/Other VSS AD4 Power/Other VSS B11 Power/Other VSS AD7 Power/Other VSS B14 Power/Other VSS AE10 Power/Other VSS B17 Power/Other VSS AE13 Power/Other VSS B20 Power/Other VSS AE16 Power/Other VSS B24 Power/Other VSS AE17 Power/Other VSS B5 Power/Other VSS AE2 Power/Other VSS B8 Power/Other VSS AE20 Power/Other VSS A12 Power/Other VSS AE24 Power/Other VSS A15 Power/Other VSS AE25 Power/Other VSS A18 Power/Other VSS AE26 Power/Other VSS A2 Power/Other VSS AE27 Power/Other VSS A21 Power/Other VSS AE28 Power/Other VSS A6 Power/Other VSS AE29 Power/Other VSS A9 Power/Other VSS AE30 Power/Other VSS AA23 Power/Other VSS AE5 Power/Other VSS AA24 Power/Other VSS AE7 Power/Other VSS AA25 Power/Other VSS AF10 Power/Other VSS AA26 Power/Other VSS AF13 Power/Other VSS AA27 Power/Other VSS AF16 Power/Other VSS AA28 Power/Other VSS AF17 Power/Other VSS AA29 Power/Other VSS AF20 Power/Other VSS AA3 Power/Other VSS AF23 Power/Other VSS AA30 Power/Other VSS AF24 Power/Other VSS AA6 Power/Other VSS AF25 Power/Other VSS AA7 Power/Other VSS AF26 Power/Other VSS AB1 Power/Other VSS AF27 Power/Other VSS AB23 Power/Other VSS AF28 Power/Other VSS AB24 Power/Other VSS AF29 Power/Other VSS AB25 Power/Other VSS AF3 Power/Other Direction Datasheet Land Listing and Signal Descriptions Table 24. Land Name Datasheet Alphabetical Land Assignments Land Signal Buffer # Type Direction Table 24. Land Name Alphabetical Land Assignments Land Signal Buffer # Type VSS AF30 Power/Other VSS AK2 Power/Other VSS AF6 Power/Other VSS AK20 Power/Other VSS AF7 Power/Other VSS AK23 Power/Other VSS AG10 Power/Other VSS AK24 Power/Other VSS AG13 Power/Other VSS AK27 Power/Other VSS AG16 Power/Other VSS AK28 Power/Other VSS AG17 Power/Other VSS AK29 Power/Other VSS AG20 Power/Other VSS AK30 Power/Other VSS AG23 Power/Other VSS AK5 Power/Other VSS AG24 Power/Other VSS AK7 Power/Other VSS AG7 Power/Other VSS AL10 Power/Other VSS AH1 Power/Other VSS AL13 Power/Other VSS AH10 Power/Other VSS AL16 Power/Other VSS AH13 Power/Other VSS AL17 Power/Other VSS AH16 Power/Other VSS AL20 Power/Other VSS AH17 Power/Other VSS AL23 Power/Other VSS AH20 Power/Other VSS AL24 Power/Other VSS AH23 Power/Other VSS AL27 Power/Other VSS AH24 Power/Other VSS AL28 Power/Other VSS AH3 Power/Other VSS AL7 Power/Other VSS AH6 Power/Other VSS AM1 Power/Other VSS AH7 Power/Other VSS AM10 Power/Other VSS AJ10 Power/Other VSS AM13 Power/Other VSS AJ13 Power/Other VSS AM16 Power/Other VSS AJ16 Power/Other VSS AM17 Power/Other VSS AJ17 Power/Other VSS AM20 Power/Other VSS AJ20 Power/Other VSS AM23 Power/Other VSS AJ23 Power/Other VSS AM24 Power/Other VSS AJ24 Power/Other VSS AM27 Power/Other VSS AJ27 Power/Other VSS AM28 Power/Other VSS AJ28 Power/Other VSS AM4 Power/Other VSS AJ29 Power/Other VSS AN1 Power/Other VSS AJ30 Power/Other VSS AN10 Power/Other VSS AJ4 Power/Other VSS AN13 Power/Other VSS AJ7 Power/Other VSS AN16 Power/Other VSS AK10 Power/Other VSS AN17 Power/Other VSS AK13 Power/Other VSS AN2 Power/Other VSS AK16 Power/Other VSS AN20 Power/Other VSS AK17 Power/Other VSS AN23 Power/Other Direction 53 Land Listing and Signal Descriptions Table 24. Land Name 54 Alphabetical Land Assignments Land Signal Buffer # Type Direction Table 24. Land Name Alphabetical Land Assignments Land Signal Buffer # Type VSS AN24 Power/Other VSS H12 Power/Other VSS AN27 Power/Other VSS H13 Power/Other VSS AN28 Power/Other VSS H14 Power/Other VSS C10 Power/Other VSS H17 Power/Other VSS C13 Power/Other VSS H18 Power/Other VSS C16 Power/Other VSS H19 Power/Other VSS C19 Power/Other VSS H20 Power/Other VSS C22 Power/Other VSS H21 Power/Other VSS C24 Power/Other VSS H22 Power/Other VSS C4 Power/Other VSS H23 Power/Other VSS C7 Power/Other VSS H24 Power/Other VSS D12 Power/Other VSS H25 Power/Other VSS D15 Power/Other VSS H26 Power/Other VSS D18 Power/Other VSS H27 Power/Other VSS D21 Power/Other VSS H28 Power/Other VSS D24 Power/Other VSS H3 Power/Other VSS D3 Power/Other VSS H6 Power/Other VSS D5 Power/Other VSS H7 Power/Other VSS D6 Power/Other VSS H8 Power/Other VSS D9 Power/Other VSS H9 Power/Other VSS E11 Power/Other VSS J4 Power/Other VSS E14 Power/Other VSS J7 Power/Other VSS E17 Power/Other VSS K2 Power/Other VSS E2 Power/Other VSS K5 Power/Other VSS E20 Power/Other VSS K7 Power/Other VSS E25 Power/Other VSS L23 Power/Other VSS E26 Power/Other VSS L24 Power/Other VSS E27 Power/Other VSS L25 Power/Other VSS E28 Power/Other VSS L26 Power/Other VSS E8 Power/Other VSS L27 Power/Other VSS F10 Power/Other VSS L28 Power/Other VSS F13 Power/Other VSS L29 Power/Other VSS F16 Power/Other VSS L3 Power/Other VSS F19 Power/Other VSS L30 Power/Other VSS F22 Power/Other VSS L6 Power/Other VSS F4 Power/Other VSS L7 Power/Other VSS F7 Power/Other VSS M1 Power/Other VSS H10 Power/Other VSS M7 Power/Other VSS H11 Power/Other VSS N3 Power/Other Direction Datasheet Land Listing and Signal Descriptions Table 24. Land Name VSS Datasheet Alphabetical Land Assignments Land Signal Buffer # Type N6 Direction Table 24. Land Name Alphabetical Land Assignments Land Signal Buffer # Type Power/Other VSS W7 Power/Other Direction VSS N7 Power/Other VSS Y2 Power/Other VSS P23 Power/Other VSS Y5 Power/Other VSS P24 Power/Other VSS Y7 Power/Other VSS P25 Power/Other AN6 Power/Other Output VSS P26 Power/Other VSS_MB_ REGULATION VSS P27 Power/Other VSS_SENSE AN4 Power/Other Output VSS P28 Power/Other VSSA B23 Power/Other VSS P29 Power/Other VTT B25 Power/Other VSS P30 Power/Other VTT B26 Power/Other VSS P4 Power/Other VTT B27 Power/Other VSS P7 Power/Other VTT B28 Power/Other VSS R2 Power/Other VTT B29 Power/Other VSS R23 Power/Other VTT B30 Power/Other VSS R24 Power/Other VTT A25 Power/Other VSS R25 Power/Other VTT A26 Power/Other VSS R26 Power/Other VTT A27 Power/Other VSS R27 Power/Other VTT A28 Power/Other VSS R28 Power/Other VTT A29 Power/Other VSS R29 Power/Other VTT A30 Power/Other VSS R30 Power/Other VTT C25 Power/Other VSS R5 Power/Other VTT C26 Power/Other VSS R7 Power/Other VTT C27 Power/Other VSS T3 Power/Other VTT C28 Power/Other VSS T6 Power/Other VTT C29 Power/Other VSS T7 Power/Other VTT C30 Power/Other VSS U7 Power/Other VTT D25 Power/Other VSS V23 Power/Other VTT D26 Power/Other VSS V24 Power/Other VTT D27 Power/Other VSS V25 Power/Other VTT D28 Power/Other VSS V26 Power/Other VTT D29 Power/Other VSS V27 Power/Other VTT D30 Power/Other VSS V28 Power/Other VTT_OUT_LEFT J1 Power/Other Output VSS V29 Power/Other VTT_OUT_RIG HT AA1 Power/Other Output VSS V3 Power/Other VTT_SEL F27 Power/Other Output VSS V30 Power/Other VSS V6 Power/Other VSS V7 Power/Other VSS W4 Power/Other 55 Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name 56 Signal Buffer Type Table 25. Direction Numerical Land Assignment Land # Land Name Signal Buffer Type Direction A2 VSS Power/Other B11 VSS Power/Other A3 RS2# Common Clock Input B12 D13# Source Synch Input/Output A4 D02# Source Synch Input/Output B13 COMP8 Power/Other Input A5 D04# Source Synch Input/Output B14 VSS Power/Other A6 VSS Power/Other B15 D53# Source Synch Input/Output A7 D07# Source Synch Input/Output B16 D55# Source Synch Input/Output A8 DBI0# Source Synch Input/Output B17 VSS Power/Other A9 VSS Power/Other B18 D57# Source Synch Input/Output A10 D08# Source Synch Input/Output B19 D60# Source Synch Input/Output A11 D09# Source Synch Input/Output B20 VSS Power/Other A12 VSS Power/Other B21 D59# Source Synch Input/Output A13 COMP0 Power/Other Input B22 D63# Source Synch Input/Output A14 D50# Source Synch Input/Output B23 VSSA Power/Other A15 VSS Power/Other B24 VSS Power/Other A16 DSTBN3# Source Synch Input/Output B25 VTT Power/Other A17 D56# Source Synch Input/Output B26 VTT Power/Other B27 VTT Power/Other B28 VTT Power/Other B29 VTT Power/Other B30 VTT Power/Other A18 VSS Power/Other A19 D61# Source Synch A20 RESERVED A21 VSS Power/Other A22 D62# Source Synch C1 DRDY# Common Clock Input/Output A23 VCCA Power/Other C2 BNR# Common Clock Input/Output A24 FC23 Power/Other C3 LOCK# Common Clock Input/Output A25 VTT Power/Other C4 VSS Power/Other A26 VTT Power/Other C5 D01# Source Synch Input/Output A27 VTT Power/Other C6 D03# Source Synch Input/Output A28 VTT Power/Other C7 VSS Power/Other A29 VTT Power/Other C8 DSTBN0# Source Synch Input/Output Input/Output Input/Output A30 VTT Power/Other C9 FC41 Power/Other B1 VSS Power/Other C10 VSS Power/Other B2 DBSY# Common Clock Input/Output C11 D11# Source Synch Input/Output B3 RS0# Common Clock Input C12 D14# Source Synch Input/Output B4 D00# Source Synch Input/Output C13 VSS Power/Other B5 VSS Power/Other C14 D52# Source Synch Input/Output B6 D05# Source Synch Input/Output C15 D51# Source Synch Input/Output B7 D06# Source Synch Input/Output C16 VSS Power/Other B8 VSS Power/Other C17 DSTBP3# Source Synch Input/Output B9 DSTBP0# Source Synch Input/Output C18 D54# Source Synch Input/Output B10 D10# Source Synch Input/Output C19 VSS Power/Other Datasheet Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name Datasheet Table 25. Signal Buffer Type Direction Numerical Land Assignment Land # Land Name Signal Buffer Type Direction C20 DBI3# Source Synch Input/Output D29 C21 D58# Source Synch Input/Output D30 VTT Power/Other C22 VSS Power/Other E2 VSS Power/Other C23 VCCIOPLL Power/Other E3 TRDY# Common Clock C24 VSS Power/Other E4 HITM# Common Clock Input/Output C25 VTT Power/Other E5 FC20 C26 VTT Power/Other E6 RESERVED C27 VTT Power/Other E7 RESERVED C28 VTT Power/Other E8 VSS Power/Other C29 VTT Power/Other E9 D19# Source Synch Input/Output C30 VTT Power/Other E10 D21# Source Synch Input/Output D1 RESERVED D2 ADS# Common Clock Input/Output Power/Other VTT Power/Other Input Power/Other E11 VSS Power/Other E12 DSTBP1# Source Synch Input/Output E13 D26# Source Synch Input/Output E14 VSS Power/Other D3 VSS D4 HIT# D5 VSS Power/Other E15 D33# Source Synch Input/Output D6 VSS Power/Other E16 D34# Source Synch Input/Output D7 D20# Source Synch Input/Output E17 VSS Power/Other D8 D12# Source Synch Input/Output E18 D39# Source Synch Input/Output Input/Output Common Clock Input/Output D9 VSS Power/Other E19 D40# Source Synch D10 D22# Source Synch Input/Output E20 VSS Power/Other D11 D15# Source Synch Input/Output E21 D42# Source Synch Input/Output D12 VSS Power/Other E22 D45# Source Synch Input/Output D13 D25# Source Synch E23 RESERVED D14 RESERVED E24 FC10 Power/Other E25 VSS Power/Other E26 VSS Power/Other E27 VSS Power/Other E28 VSS Power/Other Input/Output D15 VSS D16 RESERVED Power/Other D17 D49# Source Synch D18 VSS Power/Other D19 DBI2# Source Synch Input/Output E29 FC26 Power/Other D20 D48# Source Synch Input/Output F2 FC5 Power/Other F3 BR0# F4 VSS Power/Other Input/Output D21 VSS Power/Other D22 D46# Source Synch D23 VCCPLL Power/Other F5 RS1# Common Clock D24 VSS Power/Other F6 FC21 Power/Other D25 VTT Power/Other F7 VSS Power/Other D26 VTT Power/Other F8 D17# Source Synch Input/Output D27 VTT Power/Other F9 D18# Source Synch Input/Output D28 VTT Power/Other F10 VSS Power/Other Input/Output Common Clock Input/Output Input 57 Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name 58 Table 25. Signal Buffer Type Direction Numerical Land Assignment Land # Land Name Signal Buffer Type Direction F11 D23# Source Synch Input/Output G20 DSTBN2# Source Synch Input/Output F12 D24# Source Synch Input/Output G21 D44# Source Synch Input/Output F13 VSS Power/Other G22 D47# Source Synch Input/Output F14 D28# Source Synch Input/Output G23 RESET# Common Clock Input F15 D30# Source Synch Input/Output G24 TESTHI6 Power/Other Input F16 VSS Power/Other G25 TESTHI3 Power/Other Input F17 D37# Source Synch Input/Output G26 TESTHI5 Power/Other Input F18 D38# Source Synch Input/Output G27 TESTHI4 Power/Other Input F19 VSS Power/Other G28 BCLK1 Clock Input F20 D41# Source Synch Input/Output G29 BSEL0 Asynch CMOS Output F21 D43# Source Synch Input/Output G30 BSEL2 Asynch CMOS Output F22 VSS Power/Other H1 GTLREF0 Power/Other Input F23 RESERVED H2 GTLREF1 Power/Other Input F24 TESTHI7 Power/Other Input H3 VSS Power/Other F25 TESTHI2 Power/Other Input H4 FC35 Power/Other F26 TESTHI0 Power/Other Input H5 TESTHI10 Power/Other F27 VTT_SEL Power/Other Output H6 VSS Power/Other F28 BCLK0 Clock Input H7 VSS Power/Other F29 RESERVED H8 VSS Power/Other G1 FC27 Power/Other H9 VSS Power/Other G2 COMP2 Power/Other H10 VSS Power/Other G3 TESTHI8/ FC42 Power/Other Input H11 VSS Power/Other TESTHI9/ FC43 H12 VSS Power/Other G4 Power/Other Input H13 VSS Power/Other G5 PECI Power/Other Input/Output H14 VSS Power/Other H15 FC32 Power/Other Input H16 FC33 Power/Other VSS Power/Other G6 RESERVED G7 DEFER# Common Clock Input G8 BPRI# Common Clock Input H17 G9 D16# Source Synch Input/Output H18 VSS Power/Other H19 VSS Power/Other Input/Output H20 VSS Power/Other VSS Power/Other G10 FC38 Power/Other G11 DBI1# Source Synch G12 DSTBN1# Source Synch Input/Output H21 G13 D27# Source Synch Input/Output H22 VSS Power/Other VSS Power/Other G14 D29# Source Synch Input/Output H23 G15 D31# Source Synch Input/Output H24 VSS Power/Other VSS Power/Other G16 D32# Source Synch Input/Output H25 G17 D36# Source Synch Input/Output H26 VSS Power/Other VSS Power/Other VSS Power/Other G18 D35# Source Synch Input/Output H27 G19 DSTBP2# Source Synch Input/Output H28 Input Datasheet Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name H29 Datasheet Signal Buffer Type Table 25. Direction FC15 Power/Other H30 BSEL1 Asynch CMOS J1 VTT_OUT_LE FT Power/Other J2 FC3 Power/Other J3 FC22 Power/Other J4 VSS Power/Other J5 REQ1# Source Synch Input/Output J6 REQ4# Source Synch Input/Output J7 VSS Power/Other J8 VCC Power/Other J9 VCC Power/Other J10 VCC Power/Other J11 VCC Power/Other J12 VCC Power/Other J13 VCC Power/Other J14 VCC Power/Other J15 VCC Power/Other J16 FC31 Power/Other J17 FC34 Power/Other J18 VCC Power/Other J19 VCC Power/Other J20 VCC Power/Other J21 VCC Power/Other J22 VCC Power/Other J23 VCC Power/Other J24 VCC Power/Other J25 VCC Power/Other J26 VCC J27 VCC J28 J29 Output Output Numerical Land Assignment Land # Land Name Signal Buffer Type Direction K8 VCC Power/Other K23 VCC Power/Other K24 VCC Power/Other K25 VCC Power/Other K26 VCC Power/Other K27 VCC Power/Other K28 VCC Power/Other K29 VCC Power/Other K30 VCC Power/Other L1 LINT1 Asynch CMOS Input L2 SLP# Asynch CMOS Input L3 VSS Power/Other L4 A06# Source Synch Input/Output L5 A03# Source Synch Input/Output L6 VSS Power/Other L7 VSS Power/Other L8 VCC Power/Other L23 VSS Power/Other L24 VSS Power/Other L25 VSS Power/Other L26 VSS Power/Other L27 VSS Power/Other L28 VSS Power/Other L29 VSS Power/Other L30 VSS Power/Other M1 VSS Power/Other M2 THERMTRIP # Asynch CMOS Power/Other M3 STPCLK# Asynch CMOS Input Power/Other M4 A07# Source Synch Input/Output VCC Power/Other M5 A05# Source Synch Input/Output VCC Power/Other M6 REQ2# Source Synch Input/Output J30 VCC Power/Other K1 LINT0 Asynch CMOS Input M7 VSS Power/Other M8 VCC Power/Other K2 VSS Power/Other M23 VCC Power/Other K3 A20M# Asynch CMOS Input M24 VCC Power/Other K4 REQ0# Source Synch Input/Output M25 VCC Power/Other K5 VSS Power/Other M26 VCC Power/Other K6 REQ3# Source Synch M27 VCC Power/Other K7 VSS Power/Other M28 VCC Power/Other Input/Output Output 59 Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name 60 Signal Buffer Type Table 25. Direction Numerical Land Assignment Land # Land Name Signal Buffer Type Direction Input/Output M29 VCC Power/Other R6 ADSTB0# Source Synch M30 VCC Power/Other R7 VSS Power/Other N1 PWRGOOD Power/Other Input R8 VCC Power/Other N2 IGNNE# Asynch CMOS Input R23 VSS Power/Other N3 VSS Power/Other R24 VSS Power/Other N4 RESERVED R25 VSS Power/Other N5 RESERVED R26 VSS Power/Other N6 VSS Power/Other R27 VSS Power/Other N7 VSS Power/Other R28 VSS Power/Other N8 VCC Power/Other R29 VSS Power/Other N23 VCC Power/Other R30 VSS Power/Other N24 VCC Power/Other T1 COMP1 Power/Other Input N25 VCC Power/Other T2 DPRSTP# Asynch CMOS Input N26 VCC Power/Other T3 VSS Power/Other N27 VCC Power/Other T4 A11# Source Synch Input/Output N28 VCC Power/Other T5 A09# Source Synch Input/Output N29 VCC Power/Other T6 VSS Power/Other N30 VCC Power/Other T7 VSS Power/Other P1 DPSLP# Asynch CMOS Input T8 VCC Power/Other P2 SMI# Asynch CMOS Input T23 VCC Power/Other P3 INIT# Asynch CMOS Input T24 VCC Power/Other P4 VSS Power/Other T25 VCC Power/Other P5 RESERVED T26 VCC Power/Other P6 A04# T27 VCC Power/Other Source Synch Input/Output P7 VSS Power/Other T28 VCC Power/Other P8 VCC Power/Other T29 VCC Power/Other P23 VSS Power/Other T30 VCC Power/Other P24 VSS Power/Other U1 FC28 Power/Other P25 VSS Power/Other U2 FC29 Power/Other P26 VSS Power/Other U3 FC30 Power/Other P27 VSS Power/Other U4 A13# Source Synch Input/Output P28 VSS Power/Other U5 A12# Source Synch Input/Output P29 VSS Power/Other U6 A10# Source Synch Input/Output P30 VSS Power/Other U7 VSS Power/Other R1 COMP3 Power/Other R2 VSS Power/Other R3 FERR#/PBE# Asynch CMOS R4 A08# Source Synch R5 VSS Power/Other Input U8 VCC Power/Other U23 VCC Power/Other Output U24 VCC Power/Other Input/Output U25 VCC Power/Other U26 VCC Power/Other Datasheet Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name Datasheet Signal Buffer Type Table 25. Direction Numerical Land Assignment Land # Land Name Signal Buffer Type Direction U27 VCC Power/Other Y3 PSI# Asynch CMOS Output U28 VCC Power/Other Y4 A20# Source Synch Input/Output U29 VCC Power/Other Y5 VSS Power/Other U30 VCC Power/Other Y6 A19# Source Synch V1 MSID1 Power/Other Y7 VSS Power/Other V2 RESERVED V3 VSS Power/Other V4 A15# Source Synch V5 A14# Source Synch V6 VSS V7 VSS Output Y8 VCC Power/Other Y23 VCC Power/Other Input/Output Y24 VCC Power/Other Input/Output Y25 VCC Power/Other Power/Other Y26 VCC Power/Other Power/Other Y27 VCC Power/Other Input/Output V8 VCC Power/Other Y28 VCC Power/Other V23 VSS Power/Other Y29 VCC Power/Other V24 VSS Power/Other Y30 VCC Power/Other V25 VSS Power/Other AA1 Power/Other V26 VSS Power/Other VTT_OUT_RI GHT V27 VSS Power/Other AA2 FC39 Power/Other V28 VSS Power/Other AA3 VSS Power/Other V29 VSS Power/Other AA4 A21# Source Synch Input/Output V30 VSS Power/Other AA5 A23# Source Synch Input/Output W1 MSID0 Power/Other Output AA6 VSS Power/Other VSS Power/Other W2 TESTHI12/ FC44 AA7 Power/Other Input W3 TESTHI1 Power/Other Input AA8 VCC Power/Other AA23 VSS Power/Other W4 VSS Power/Other AA24 VSS Power/Other W5 A16# Source Synch Input/Output AA25 VSS Power/Other W6 A18# Source Synch Input/Output AA26 VSS Power/Other W7 VSS Power/Other AA27 VSS Power/Other Output W8 VCC Power/Other AA28 VSS Power/Other W23 VCC Power/Other AA29 VSS Power/Other W24 VCC Power/Other AA30 VSS Power/Other W25 VCC Power/Other AB1 VSS Power/Other W26 VCC Power/Other AB2 IERR# Asynch CMOS W27 VCC Power/Other AB3 FC37 Power/Other W28 VCC Power/Other AB4 A26# Source Synch Input/Output W29 VCC Power/Other AB5 A24# Source Synch Input/Output W30 VCC Power/Other AB6 A17# Source Synch Input/Output Y1 FC0/ BOOTSELECT Power/Other AB7 VSS Power/Other Y2 VSS Power/Other AB8 VCC Power/Other AB23 VSS Power/Other Output 61 Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name 62 Signal Buffer Type Table 25. Direction Numerical Land Assignment Land # Land Name Signal Buffer Type Direction Input AB24 VSS Power/Other AE1 TCK TAP AB25 VSS Power/Other AE2 VSS Power/Other AB26 VSS Power/Other AE3 FC18 Power/Other AB27 VSS Power/Other AE4 RESERVED AB28 VSS Power/Other AE5 VSS AB29 VSS Power/Other AE6 RESERVED AB30 VSS Power/Other AC1 TMS TAP Input AC2 DBR# Power/Other Output AC3 VSS Power/Other AC4 RESERVED AC5 A25# Source Synch AC6 VSS Power/Other AE13 VSS Power/Other AC7 VSS Power/Other AE14 VCC Power/Other Input/Output Power/Other AE7 VSS Power/Other AE8 SKTOCC# Power/Other AE9 VCC Power/Other AE10 VSS Power/Other AE11 VCC Power/Other AE12 VCC Power/Other AC8 VCC Power/Other AE15 VCC Power/Other AC23 VCC Power/Other AE16 VSS Power/Other AC24 VCC Power/Other AE17 VSS Power/Other AC25 VCC Power/Other AE18 VCC Power/Other AC26 VCC Power/Other AE19 VCC Power/Other AC27 VCC Power/Other AE20 VSS Power/Other AC28 VCC Power/Other AE21 VCC Power/Other AC29 VCC Power/Other AE22 VCC Power/Other AC30 VCC Power/Other AE23 VCC Power/Other AD1 TDI TAP AE24 VSS Power/Other AD2 BPM2# AE25 VSS Power/Other AD3 FC36 AE26 VSS Power/Other Input Common Clock Input/Output Power/Other AD4 VSS Power/Other AE27 VSS Power/Other AD5 ADSTB1# Source Synch Input/Output AE28 VSS Power/Other AD6 A22# Source Synch Input/Output AE29 VSS Power/Other AD7 VSS Power/Other AE30 VSS Power/Other Output AD8 VCC Power/Other AF1 TDO AD23 VCC Power/Other AF2 BPM4# AD24 VCC Power/Other AF3 VSS Power/Other AD25 VCC Power/Other AF4 A28# Source Synch Input/Output AD26 VCC Power/Other AF5 A27# Source Synch Input/Output AD27 VCC Power/Other AF6 VSS Power/Other AD28 VCC Power/Other AF7 VSS Power/Other AD29 VCC Power/Other AF8 VCC Power/Other AD30 VCC Power/Other AF9 VCC Power/Other TAP Output Common Clock Input/Output Datasheet Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name Datasheet Signal Buffer Type Table 25. Direction Numerical Land Assignment Land # Land Name Signal Buffer Type AF10 VSS Power/Other AG19 AF11 VCC Power/Other AG20 VSS Power/Other AF12 VCC Power/Other AG21 VCC Power/Other VCC Direction Power/Other AF13 VSS Power/Other AG22 VCC Power/Other AF14 VCC Power/Other AG23 VSS Power/Other AF15 VCC Power/Other AG24 VSS Power/Other AF16 VSS Power/Other AG25 VCC Power/Other AF17 VSS Power/Other AG26 VCC Power/Other AF18 VCC Power/Other AG27 VCC Power/Other AF19 VCC Power/Other AG28 VCC Power/Other AF20 VSS Power/Other AG29 VCC Power/Other AF21 VCC Power/Other AG30 VCC Power/Other AF22 VCC Power/Other AH1 VSS Power/Other AF23 VSS Power/Other AH2 RESERVED AF24 VSS Power/Other AH3 VSS Power/Other AF25 VSS Power/Other AH4 A32# Source Synch Input/Output AF26 VSS Power/Other AH5 A33# Source Synch Input/Output AF27 VSS Power/Other AH6 VSS Power/Other AF28 VSS Power/Other AH7 VSS Power/Other AF29 VSS Power/Other AH8 VCC Power/Other AF30 VSS Power/Other AH9 VCC Power/Other AG1 TRST# AH10 VSS Power/Other AG2 BPM3# Common Clock Input/Output TAP Input AH11 VCC Power/Other AG3 BPM5# Common Clock Input/Output AH12 VCC Power/Other AG4 A30# Source Synch Input/Output AH13 VSS Power/Other AG5 A31# Source Synch Input/Output AH14 VCC Power/Other AG6 A29# Source Synch Input/Output AH15 VCC Power/Other AG7 VSS Power/Other AH16 VSS Power/Other AG8 VCC Power/Other AH17 VSS Power/Other AG9 VCC Power/Other AH18 VCC Power/Other AG10 VSS Power/Other AH19 VCC Power/Other AG11 VCC Power/Other AH20 VSS Power/Other AG12 VCC Power/Other AH21 VCC Power/Other AG13 VSS Power/Other AH22 VCC Power/Other AG14 VCC Power/Other AH23 VSS Power/Other AG15 VCC Power/Other AH24 VSS Power/Other AG16 VSS Power/Other AH25 VCC Power/Other AG17 VSS Power/Other AH26 VCC Power/Other AG18 VCC Power/Other AH27 VCC Power/Other 63 Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name 64 Signal Buffer Type Table 25. Direction Numerical Land Assignment Land # Land Name Signal Buffer Type AH28 VCC Power/Other AK7 VSS Power/Other AH29 VCC Power/Other AK8 VCC Power/Other AH30 VCC AK9 VCC Power/Other AJ1 BPM1# Common Clock Input/Output Power/Other AK10 VSS Power/Other AJ2 BPM0# Common Clock Input/Output AK11 VCC Power/Other AJ3 ITP_CLK1 AK12 VCC Power/Other TAP Input AJ4 VSS Power/Other AK13 VSS Power/Other AJ5 A34# Source Synch Input/Output AK14 VCC Power/Other AJ6 A35# Source Synch Input/Output AK15 VCC Power/Other AJ7 VSS Power/Other AK16 VSS Power/Other AJ8 VCC Power/Other AK17 VSS Power/Other AJ9 VCC Power/Other AK18 VCC Power/Other AJ10 VSS Power/Other AK19 VCC Power/Other AJ11 VCC Power/Other AK20 VSS Power/Other AJ12 VCC Power/Other AK21 VCC Power/Other AJ13 VSS Power/Other AK22 VCC Power/Other AJ14 VCC Power/Other AK23 VSS Power/Other AJ15 VCC Power/Other AK24 VSS Power/Other AJ16 VSS Power/Other AK25 VCC Power/Other AJ17 VSS Power/Other AK26 VCC Power/Other AJ18 VCC Power/Other AK27 VSS Power/Other AJ19 VCC Power/Other AK28 VSS Power/Other AJ20 VSS Power/Other AK29 VSS Power/Other AJ21 VCC Power/Other AK30 VSS Power/Other AJ22 VCC Power/Other AL1 FC25 Power/Other AJ23 VSS Power/Other AL2 PROCHOT# Asynch CMOS Direction Input/Output AJ24 VSS Power/Other AL3 VRDSEL Power/Other AJ25 VCC Power/Other AL4 VID5 Asynch CMOS Output AJ26 VCC Power/Other AL5 VID1 Asynch CMOS Output AJ27 VSS Power/Other AL6 VID3 Asynch CMOS Output AJ28 VSS Power/Other AL7 VSS Power/Other AJ29 VSS Power/Other AL8 VCC Power/Other AJ30 VSS Power/Other AL9 VCC Power/Other AK1 FC24 Power/Other AL10 VSS Power/Other AK2 VSS Power/Other AL11 VCC Power/Other AK3 ITP_CLK0 TAP Input AL12 VCC Power/Other AK4 VID4 Asynch CMOS Output AL13 VSS Power/Other AK5 VSS Power/Other AL14 VCC Power/Other AK6 FC8 Power/Other AL15 VCC Power/Other Datasheet Land Listing and Signal Descriptions Table 25. Numerical Land Assignment Land # Land Name AL16 Datasheet VSS Signal Buffer Type Table 25. Direction Numerical Land Assignment Land # Land Name Signal Buffer Type Power/Other AM25 VCC Power/Other Direction AL17 VSS Power/Other AM26 VCC Power/Other AL18 VCC Power/Other AM27 VSS Power/Other AL19 VCC Power/Other AM28 VSS Power/Other AL20 VSS Power/Other AM29 VCC Power/Other AL21 VCC Power/Other AM30 VCC Power/Other AL22 VCC Power/Other AN1 VSS Power/Other AL23 VSS Power/Other AN2 VSS Power/Other AL24 VSS Power/Other AN3 VCC_SENSE Power/Other Output AL25 VCC Power/Other AN4 VSS_SENSE Power/Other Output AL26 VCC Power/Other AN5 Power/Other Output AL27 VSS Power/Other VCC_MB_ REGULATION AL28 VSS Power/Other AN6 VSS_MB_ REGULATION Power/Other Output AL29 VCC Power/Other AN7 VID_SELECT Power/Other Output AL30 VCC Power/Other AN8 VCC Power/Other AM1 VSS Power/Other AN9 VCC Power/Other AM10 VSS Power/Other AN10 VSS Power/Other AM11 VCC Power/Other AN11 VCC Power/Other AM12 VCC Power/Other AN12 VCC Power/Other AM13 VSS Power/Other AN13 VSS Power/Other AM14 VCC Power/Other AN14 VCC Power/Other AM15 VCC Power/Other AN15 VCC Power/Other AM16 VSS Power/Other AN16 VSS Power/Other AM17 VSS Power/Other AN17 VSS Power/Other AM18 VCC Power/Other AN18 VCC Power/Other AM19 VCC Power/Other AN19 VCC Power/Other AM2 VID0 Asynch CMOS Output AN20 VSS Power/Other AM3 VID2 Asynch CMOS Output AN21 VCC Power/Other AM4 VSS Power/Other AN22 VCC Power/Other AM5 VID6 Asynch CMOS AN23 VSS Power/Other AM6 FC40 Power/Other AM7 VID7 Asynch CMOS AM8 VCC AM9 Output AN24 VSS Power/Other AN25 VCC Power/Other Power/Other AN26 VCC Power/Other VCC Power/Other AN27 VSS Power/Other AM20 VSS Power/Other AN28 VSS Power/Other AM21 VCC Power/Other AN29 VCC Power/Other AM22 VCC Power/Other AN30 VCC Power/Other AM23 VSS Power/Other AM24 VSS Power/Other Output 65 Land Listing and Signal Descriptions 4.2 Alphabetical Signals Reference Table 26. Signal Description (Sheet 1 of 10) Name A[35:3]# Type Input/ Output Description A[35:3]# (Address) define a 236-byte physical memory address space. In sub-phase 1 of the address phase, these signals transmit the address of a transaction. In sub-phase 2, these signals transmit transaction type information. These signals must connect the appropriate pins/lands of all agents on the processor FSB. A[35:3]# are source synchronous signals and are latched into the receiving buffers by ADSTB[1:0]#. On the active-to-inactive transition of RESET#, the processor samples a subset of the A[35:3]# signals to determine power-on configuration. See Section 6.1 for more details. A20M# Input If A20M# (Address-20 Mask) is asserted, the processor masks physical address bit 20 (A20#) before looking up a line in any internal cache and before driving a read/write transaction on the bus. Asserting A20M# emulates the 8086 processor's address wrap-around at the 1-MB boundary. Assertion of A20M# is only supported in real mode. A20M# is an asynchronous signal. However, to ensure recognition of this signal following an Input/Output write instruction, it must be valid along with the TRDY# assertion of the corresponding Input/ Output Write bus transaction. ADS# Input/ Output ADS# (Address Strobe) is asserted to indicate the validity of the transaction address on the A[35:3]# and REQ[4:0]# signals. All bus agents observe the ADS# activation to begin protocol checking, address decode, internal snoop, or deferred reply ID match operations associated with the new transaction. Address strobes are used to latch A[35:3]# and REQ[4:0]# on their rising and falling edges. Strobes are associated with signals as shown below. ADSTB[1:0]# BCLK[1:0] Input/ Output Input Signals Associated Strobe REQ[4:0]#, A[16:3]# ADSTB0# A[35:17]# ADSTB1# The differential pair BCLK (Bus Clock) determines the FSB frequency. All processor FSB agents must receive these signals to drive their outputs and latch their inputs. All external timing parameters are specified with respect to the rising edge of BCLK0 crossing VCROSS. BNR# 66 Input/ Output BNR# (Block Next Request) is used to assert a bus stall by any bus agent unable to accept new bus transactions. During a bus stall, the current bus owner cannot issue any new transactions. Datasheet Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 2 of 10) Name Type Description BPM[5:0]# (Breakpoint Monitor) are breakpoint and performance monitor signals. They are outputs from the processor which indicate the status of breakpoints and programmable counters used for monitoring processor performance. BPM[5:0]# should connect the appropriate pins/lands of all processor FSB agents. BPM[5:0]# Input/ Output BPM4# provides PRDY# (Probe Ready) functionality for the TAP port. PRDY# is a processor output used by debug tools to determine processor debug readiness. BPM5# provides PREQ# (Probe Request) functionality for the TAP port. PREQ# is used by debug tools to request debug operation of the processor. These signals do not have on-die termination. Refer to Section 2.6.2 for termination requirements. BPRI# BR0# Datasheet Input Input/ Output BPRI# (Bus Priority Request) is used to arbitrate for ownership of the processor FSB. It must connect the appropriate pins/lands of all processor FSB agents. Observing BPRI# active (as asserted by the priority agent) causes all other agents to stop issuing new requests, unless such requests are part of an ongoing locked operation. The priority agent keeps BPRI# asserted until all of its requests are completed, then releases the bus by de-asserting BPRI#. BR0# drives the BREQ0# signal in the system and is used by the processor to request the bus. During power-on configuration this signal is sampled to determine the agent ID = 0. This signal does not have on-die termination and must be terminated. BSEL[2:0] Output The BCLK[1:0] frequency select signals BSEL[2:0] are used to select the processor input clock frequency. Table 17 defines the possible combinations of the signals and the frequency associated with each combination. The required frequency is determined by the processor, chipset, and clock synthesizer. All agents must operate at the same frequency. For more information about these signals, including termination recommendations refer to Section 2.8.2. COMP[3:0], COMP8 Analog COMP[3:0] and COMP8 must be terminated to VSS on the system board using precision resistors. 67 Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 3 of 10) Name Type Description D[63:0]# (Data) are the data signals. These signals provide a 64bit data path between the processor FSB agents, and must connect the appropriate pins/lands on all such agents. The data driver asserts DRDY# to indicate a valid data transfer. D[63:0]# are quad-pumped signals and will, thus, be driven four times in a common clock period. D[63:0]# are latched off the falling edge of both DSTBP[3:0]# and DSTBN[3:0]#. Each group of 16 data signals correspond to a pair of one DSTBP# and one DSTBN#. The following table shows the grouping of data signals to data strobes and DBI#. D[63:0]# Input/ Output Quad-Pumped Signal Groups Data Group DSTBN#/DSTBP# DBI# D[15:0]# 0 0 D[31:16]# 1 1 D[47:32]# 2 2 D[63:48]# 3 3 Furthermore, the DBI# signals determine the polarity of the data signals. Each group of 16 data signals corresponds to one DBI# signal. When the DBI# signal is active, the corresponding data group is inverted and therefore sampled active high. DBI[3:0]# (Data Bus Inversion) are source synchronous and indicate the polarity of the D[63:0]# signals.The DBI[3:0]# signals are activated when the data on the data bus is inverted. If more than half the data bits, within a 16-bit group, would have been asserted electrically low, the bus agent may invert the data bus signals for that particular sub-phase for that 16-bit group. DBI[3:0]# DBR# DBSY# 68 Input/ Output DBI[3:0] Assignment To Data Bus Bus Signal Data Bus Signals DBI3# D[63:48]# DBI2# D[47:32]# DBI1# D[31:16]# DBI0# D[15:0]# Output DBR# (Debug Reset) is used only in processor systems where no debug port is implemented on the system board. DBR# is used by a debug port interposer so that an in-target probe can drive system reset. If a debug port is implemented in the system, DBR# is a no connect in the system. DBR# is not a processor signal. Input/ Output DBSY# (Data Bus Busy) is asserted by the agent responsible for driving data on the processor FSB to indicate that the data bus is in use. The data bus is released after DBSY# is de-asserted. This signal must connect the appropriate pins/lands on all processor FSB agents. Datasheet Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 4 of 10) Name Type Description Input DEFER# is asserted by an agent to indicate that a transaction cannot be ensured in-order completion. Assertion of DEFER# is normally the responsibility of the addressed memory or input/ output agent. This signal must connect the appropriate pins/lands of all processor FSB agents. Input DPRSTP#, when asserted on the platform, causes the processor to transition from the Deep Sleep State to the Deeper Sleep state. To return to the Deep Sleep State, DPRSTP# must be de-asserted. Use of the DPRSTP# pin, and corresponding low power state, requires chipset support and may not be available on all platforms. NOTE: Some processors may not have the Deeper Sleep State enabled, refer to the Specification Update for specific sku and stepping guidance. DPSLP# Input DPSLP#, when asserted on the platform, causes the processor to transition from the Sleep State to the Deep Sleep state. To return to the Sleep State, DPSLP# must be de-asserted. Use of the DPSLP# pin, and corresponding low power state, requires chipset support and may not be available on all platforms. NOTE: Some processors may not have the Deep Sleep State enabled, refer to the Specification Update for specific processor and stepping guidance. DRDY# Input/ Output DRDY# (Data Ready) is asserted by the data driver on each data transfer, indicating valid data on the data bus. In a multi-common clock data transfer, DRDY# may be de-asserted to insert idle clocks. This signal must connect the appropriate pins/lands of all processor FSB agents. DEFER# DPRSTP# DSTBN[3:0]# are the data strobes used to latch in D[63:0]#. DSTBN[3:0]# Input/ Output Signals Associated Strobe D[15:0]#, DBI0# DSTBN0# D[31:16]#, DBI1# DSTBN1# D[47:32]#, DBI2# DSTBN2# D[63:48]#, DBI3# DSTBN3# DSTBP[3:0]# are the data strobes used to latch in D[63:0]#. Signals DSTBP[3:0]# Datasheet Input/ Output Associated Strobe D[15:0]#, DBI0# DSTBP0# D[31:16]#, DBI1# DSTBP1# D[47:32]#, DBI2# DSTBP2# D[63:48]#, DBI3# DSTBP3# FC0/BOOTSELECT Other FC0/BOOTSELECT is not used by the processor. When this land is tied to VSS previous processors based on the Intel NetBurst® microarchitecture should be disabled and prevented from booting. FCx Other FC signals are signals that are available for compatibility with other processors. 69 Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 5 of 10) Name Type Description FERR#/PBE# Output FERR#/PBE# (floating point error/pending break event) is a multiplexed signal and its meaning is qualified by STPCLK#. When STPCLK# is not asserted, FERR#/PBE# indicates a floating-point error and will be asserted when the processor detects an unmasked floating-point error. When STPCLK# is not asserted, FERR#/PBE# is similar to the ERROR# signal on the Intel 387 coprocessor, and is included for compatibility with systems using MS-DOS*-type floating-point error reporting. When STPCLK# is asserted, an assertion of FERR#/PBE# indicates that the processor has a pending break event waiting for service. The assertion of FERR#/ PBE# indicates that the processor should be returned to the Normal state. For additional information on the pending break event functionality, including the identification of support of the feature and enable/disable information, refer to volume 3 of the Intel Architecture Software Developer's Manual and the Intel Processor Identification and the CPUID Instruction application note. GTLREF[1:0] Input HIT# HITM# IERR# Input/ Output Input/ Output Output GTLREF[1:0] determine the signal reference level for GTL+ input signals. GTLREF is used by the GTL+ receivers to determine if a signal is a logical 0 or logical 1. HIT# (Snoop Hit) and HITM# (Hit Modified) convey transaction snoop operation results. Any FSB agent may assert both HIT# and HITM# together to indicate that it requires a snoop stall, which can be continued by reasserting HIT# and HITM# together. IERR# (Internal Error) is asserted by a processor as the result of an internal error. Assertion of IERR# is usually accompanied by a SHUTDOWN transaction on the processor FSB. This transaction may optionally be converted to an external error signal (e.g., NMI) by system core logic. The processor will keep IERR# asserted until the assertion of RESET#. This signal does not have on-die termination. Refer to Section 2.6.2 for termination requirements. IGNNE# Input IGNNE# (Ignore Numeric Error) is asserted to the processor to ignore a numeric error and continue to execute noncontrol floatingpoint instructions. If IGNNE# is de-asserted, the processor generates an exception on a noncontrol floating-point instruction if a previous floating-point instruction caused an error. IGNNE# has no effect when the NE bit in control register 0 (CR0) is set. IGNNE# is an asynchronous signal. However, to ensure recognition of this signal following an Input/Output write instruction, it must be valid along with the TRDY# assertion of the corresponding Input/ Output Write bus transaction. INIT# Input INIT# (Initialization), when asserted, resets integer registers inside the processor without affecting its internal caches or floating-point registers. The processor then begins execution at the power-on Reset vector configured during power-on configuration. The processor continues to handle snoop requests during INIT# assertion. INIT# is an asynchronous signal and must connect the appropriate pins/lands of all processor FSB agents. If INIT# is sampled active on the active to inactive transition of RESET#, then the processor executes its Built-in Self-Test (BIST). 70 Datasheet Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 6 of 10) Name ITP_CLK[1:0] LINT[1:0] Type Description Input ITP_CLK[1:0] are copies of BCLK that are used only in processor systems where no debug port is implemented on the system board. ITP_CLK[1:0] are used as BCLK[1:0] references for a debug port implemented on an interposer. If a debug port is implemented in the system, ITP_CLK[1:0] are no connects in the system. These are not processor signals. Input LINT[1:0] (Local APIC Interrupt) must connect the appropriate pins/lands of all APIC Bus agents. When the APIC is disabled, the LINT0 signal becomes INTR, a maskable interrupt request signal, and LINT1 becomes NMI, a nonmaskable interrupt. INTR and NMI are backward compatible with the signals of those names on the Pentium processor. Both signals are asynchronous. Both of these signals must be software configured using BIOS programming of the APIC register space to be used either as NMI/ INTR or LINT[1:0]. Because the APIC is enabled by default after Reset, operation of these signals as LINT[1:0] is the default configuration. LOCK# When the priority agent asserts BPRI# to arbitrate for ownership of the processor FSB, it will wait until it observes LOCK# de-asserted. This enables symmetric agents to retain ownership of the processor FSB throughout the bus locked operation and ensure the atomicity of lock. MSID[1:0] Output On the processor these signals are connected on the package to VSS. As an alternative to MSID, Intel has implemented the Power Segment Identifier (PSID) to report the maximum Thermal Design Power of the processor. Refer to Section 2.5 for additional information regarding PSID. PECI Input/ Output PECI is a proprietary one-wire bus interface. See Chapter 5.3 for details. Input/ Output As an output, PROCHOT# (Processor Hot) will go active when the processor temperature monitoring sensor detects that the processor has reached its maximum safe operating temperature. This indicates that the processor Thermal Control Circuit (TCC) has been activated, if enabled. As an input, assertion of PROCHOT# by the system will activate the TCC, if enabled. The TCC will remain active until the system de-asserts PROCHOT#. See Section 5.2.4 for more details. Output Processor Power Status Indicator Signal. This signal may be asserted when the processor is in the Deeper Sleep State. PSI# can be used to improve load efficiency of the voltage regulator, resulting in platform power savings. PROCHOT# PSI# Datasheet Input/ Output LOCK# indicates to the system that a transaction must occur atomically. This signal must connect the appropriate pins/lands of all processor FSB agents. For a locked sequence of transactions, LOCK# is asserted from the beginning of the first transaction to the end of the last transaction. 71 Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 7 of 10) Name PWRGOOD Type Input Description PWRGOOD (Power Good) is a processor input. The processor requires this signal to be a clean indication that the clocks and power supplies are stable and within their specifications. ‘Clean’ implies that the signal will remain low (capable of sinking leakage current), without glitches, from the time that the power supplies are turned on until they come within specification. The signal must then transition monotonically to a high state. PWRGOOD can be driven inactive at any time, but clocks and power must again be stable before a subsequent rising edge of PWRGOOD. The PWRGOOD signal must be supplied to the processor; it is used to protect internal circuits against voltage sequencing issues. It should be driven high throughout boundary scan operation. REQ[4:0]# RESET# Input/ Output Input REQ[4:0]# (Request Command) must connect the appropriate pins/lands of all processor FSB agents. They are asserted by the current bus owner to define the currently active transaction type. These signals are source synchronous to ADSTB0#. Asserting the RESET# signal resets the processor to a known state and invalidates its internal caches without writing back any of their contents. For a power-on Reset, RESET# must stay active for at least one millisecond after VCC and BCLK have reached their proper specifications. On observing active RESET#, all FSB agents will deassert their outputs within two clocks. RESET# must not be kept asserted for more than 10 ms while PWRGOOD is asserted. A number of bus signals are sampled at the active-to-inactive transition of RESET# for power-on configuration. These configuration options are described in the Section 6.1. This signal does not have on-die termination and must be terminated on the system board. 72 RESERVED All RESERVED lands must remain unconnected. Connection of these lands to VCC, VSS, VTT, or to any other signal (including each other) can result in component malfunction or incompatibility with future processors. RS[2:0]# Input RS[2:0]# (Response Status) are driven by the response agent (the agent responsible for completion of the current transaction), and must connect the appropriate pins/lands of all processor FSB agents. SKTOCC# Output SKTOCC# (Socket Occupied) will be pulled to ground by the processor. System board designers may use this signal to determine if the processor is present. Datasheet Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 8 of 10) Name SLP# SMI# Type Description Input SLP# (Sleep), when asserted in Extended Stop Grant or Stop Grant state, causes the processor to enter the Sleep state. In the Sleep state, the processor stops providing internal clock signals to all units, leaving only the Phase-Locked Loop (PLL) still operating. Processors in this state will not recognize snoops or interrupts. The processor will recognize only assertion of the RESET# signal, deassertion of SLP#, and removal of the BCLK input while in Sleep state. If SLP# is de-asserted, the processor exits Sleep state and returns to Extended Stop Grant or Stop Grant state, restarting its internal clock signals to the bus and processor core units. If DPSLP# is asserted while in the Sleep state, the processor will exit the Sleep state and transition to the Deep Sleep state. Use of the SLP# pin, and corresponding low power state, requires chipset support and may not be available on all platforms. NOTE: Some processors may not have the Sleep State enabled, refer to the Specification Update for specific processor and stepping guidance. Input SMI# (System Management Interrupt) is asserted asynchronously by system logic. On accepting a System Management Interrupt, the processor saves the current state and enter System Management Mode (SMM). An SMI Acknowledge transaction is issued, and the processor begins program execution from the SMM handler. If SMI# is asserted during the de-assertion of RESET#, the processor will tri-state its outputs. STPCLK# Input STPCLK# (Stop Clock), when asserted, causes the processor to enter a low power Stop-Grant state. The processor issues a StopGrant Acknowledge transaction, and stops providing internal clock signals to all processor core units except the FSB and APIC units. The processor continues to snoop bus transactions and service interrupts while in Stop-Grant state. When STPCLK# is deasserted, the processor restarts its internal clock to all units and resumes execution. The assertion of STPCLK# has no effect on the bus clock; STPCLK# is an asynchronous input. TCK Input TCK (Test Clock) provides the clock input for the processor Test Bus (also known as the Test Access Port). TDI Input TDI (Test Data In) transfers serial test data into the processor. TDI provides the serial input needed for JTAG specification support. TDO Output TDO (Test Data Out) transfers serial test data out of the processor. TDO provides the serial output needed for JTAG specification support. Input The TESTHI[12,10:0] lands must be connected to the processor’s appropriate power source (refer to VTT_OUT_LEFT and VTT_OUT_RIGHT signal description) through a resistor for proper processor operation. See Section 2.4 for more details. TESTHI[12,10:0] Datasheet 73 Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 9 of 10) Name Type Description Output In the event of a catastrophic cooling failure, the processor will automatically shut down when the silicon has reached a temperature approximately 20 °C above the maximum TC. Assertion of THERMTRIP# (Thermal Trip) indicates the processor junction temperature has reached a level beyond where permanent silicon damage may occur. Upon assertion of THERMTRIP#, the processor will shut off its internal clocks (thus, halting program execution) in an attempt to reduce the processor junction temperature. To protect the processor, its core voltage (VCC) must be removed following the assertion of THERMTRIP#. Driving of the THERMTRIP# signal is enabled within 10 μs of the assertion of PWRGOOD (provided VTT and VCC are asserted) and is disabled on de-assertion of PWRGOOD (if VTT or VCC are not valid, THERMTRIP# may also be disabled). Once activated, THERMTRIP# remains latched until PWRGOOD, VTT or VCC is de-asserted. While the deassertion of the PWRGOOD, VTT or VCC signal will de-assert THERMTRIP#, if the processor’s junction temperature remains at or above the trip level, THERMTRIP# will again be asserted within 10 μs of the assertion of PWRGOOD (provided VTT and VCC are valid). TMS Input TMS (Test Mode Select) is a JTAG specification support signal used by debug tools. TRDY# Input TRDY# (Target Ready) is asserted by the target to indicate that it is ready to receive a write or implicit writeback data transfer. TRDY# must connect the appropriate pins/lands of all FSB agents. TRST# Input TRST# (Test Reset) resets the Test Access Port (TAP) logic. TRST# must be driven low during power on Reset. VCC Input VCC are the power pins for the processor. The voltage supplied to these pins is determined by the VID[7:0] pins. VCCA Input VCCA provides isolated power for internal PLLs on previous generation processors. It may be left as a No-Connect on boards supporting the processor. VCCIOPLL Input VCCIOPLL provides isolated power for internal processor FSB PLLs on previous generation processors. It may be left as a No-Connect on boards supporting the processor. VCCPLL Input THERMTRIP# VCC_SENSE VCC_MB_ REGULATION 74 VCCPLL provides isolated power for internal processor FSB PLLs. Output VCC_SENSE is an isolated low impedance connection to processor core power (VCC). It can be used to sense or measure voltage near the silicon with little noise. Output This land is provided as a voltage regulator feedback sense point for VCC. It is connected internally in the processor package to the sense point land U27 as described in the Voltage Regulator Design Guide. Datasheet Land Listing and Signal Descriptions Table 26. Signal Description (Sheet 10 of 10) Name Type Description VID[7:0] Output The VID (Voltage ID) signals are used to support automatic selection of power supply voltages (VCC). Refer to the Voltage Regulator Design Guide for more information. The voltage supply for these signals must be valid before the VR can supply VCC to the processor. Conversely, the VR output must be disabled until the voltage supply for the VID signals becomes valid. The VID signals are needed to support the processor voltage specification variations. See Table 2 for definitions of these signals. The VR must supply the voltage that is requested by the signals, or disable itself. VID_SELECT Output This land is tied high on the processor package and is used by the VR to choose the proper VID table. Refer to the Voltage Regulator Design Guide for more information. VRDSEL Input This input should be left as a no connect in order for the processor to boot. The processor will not boot on legacy platforms where this land is connected to VSS. VSS Input VSS are the ground pins for the processor and should be connected to the system ground plane. VSSA Input VSSA provides isolated ground for internal PLLs on previous generation processors. It may be left as a No-Connect on boards supporting the processor. VSS_SENSE Output VSS_SENSE is an isolated low impedance connection to processor core VSS. It can be used to sense or measure ground near the silicon with little noise. Output This land is provided as a voltage regulator feedback sense point for VSS. It is connected internally in the processor package to the sense point land V27 as described in the Voltage Regulator Design Guide. VSS_MB_ REGULATION VTT Miscellaneous voltage supply. VTT_OUT_LEFT Output The VTT_OUT_LEFT and VTT_OUT_RIGHT signals are included to provide a voltage supply for some signals that require termination to VTT on the motherboard. Output The VTT_SEL signal is used to select the correct VTT voltage level for the processor. This land is connected internally in the package to VSS. VTT_OUT_RIGHT VTT_SEL 75 Datasheet Land Listing and Signal Descriptions 76 Datasheet Thermal Specifications and Design Considerations 5 Thermal Specifications and Design Considerations 5.1 Processor Thermal Specifications The processor requires a thermal solution to maintain temperatures within the operating limits as set forth in Section 5.1.1. Any attempt to operate the processor outside these operating limits may result in permanent damage to the processor and potentially other components within the system. As processor technology changes, thermal management becomes increasingly crucial when building computer systems. Maintaining the proper thermal environment is key to reliable, long-term system operation. A complete thermal solution includes both component and system level thermal management features. Component level thermal solutions can include active or passive heatsinks attached to the processor Integrated Heat Spreader (IHS). Typical system level thermal solutions may consist of system fans combined with ducting and venting. For more information on designing a component level thermal solution, refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2). Note: The boxed processor will ship with a component thermal solution. Refer to Chapter 7 for details on the boxed processor. 5.1.1 Thermal Specifications To allow for the optimal operation and long-term reliability of Intel processor-based systems, the system/processor thermal solution should be designed such that the processor remains within the minimum and maximum case temperature (TC) specifications when operating at or below the Thermal Design Power (TDP) value listed per frequency in Table 27. Thermal solutions not designed to provide this level of thermal capability may affect the long-term reliability of the processor and system. For more details on thermal solution design, refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2). The processor uses a methodology for managing processor temperatures which is intended to support acoustic noise reduction through fan speed control. Selection of the appropriate fan speed is based on the relative temperature data reported by the processor’s Platform Environment Control Interface (PECI) bus as described in Section 5.3. If the value reported using PECI is less than TCONTROL, then the case temperature is permitted to exceed the Thermal Profile. If the value reported using PECI is greater than or equal to TCONTROL, then the processor case temperature must remain at or below the temperature as specified by the thermal profile. The temperature reported over PECI is always a negative value and represents a delta below the onset of thermal control circuit (TCC) activation, as indicated by PROCHOT# (see Section 5.2). Systems that implement fan speed control must be designed to take these conditions in to account. Systems that do not alter the fan speed only need to ensure the case temperature meets the thermal profile specifications. To determine a processor's case temperature specification based on the thermal profile, it is necessary to accurately measure processor power dissipation. Intel has developed a methodology for accurate power measurement that correlates to Intel test temperature and voltage conditions. Refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2) for the details of this methodology. Datasheet 77 Thermal Specifications and Design Considerations The case temperature is defined at the geometric top center of the processor. Analysis indicates that real applications are unlikely to cause the processor to consume maximum power dissipation for sustained time periods. Intel recommends that complete thermal solution designs target the Thermal Design Power (TDP) indicated in Table 27 instead of the maximum processor power consumption. The Thermal Monitor feature is designed to protect the processor in the unlikely event that an application exceeds the TDP recommendation for a sustained periods of time. For more details on the usage of this feature, refer to Section 5.2. In all cases the Thermal Monitor or Thermal Monitor 2 feature must be enabled for the processor to remain within specification. Table 27. Processor Thermal Specifications Core Processor Frequency Number (GHz) Thermal Design Power (W)3,4 Extended HALT Power (W)1 Deeper Sleep Power (W)2 E8600 3.33 65.0 8 6 E8500 3.16 65.0 8 6 E8400 3 65.0 8 6 E8300 2.83 65.0 8 6 E8200 2.66 65.0 8 6 E8190 2.66 65.0 8 6 E7600 E7500 E7400 E7300 E7200 3.06 GHz 2.93 2.80 2.66 2.53 65.0 65.0 65.0 65.0 65.0 8 8 8 8 8 6 6 6 6 6 775_VR_ CONFIG_06 Guidance5 Minimum TC (°C) Maximum TC (°C) Notes 5 775_VR_ CONFIG_06 (65 W) 5 5 5 5 See Table 28 and Figure 14 5 775_VR_CONFIG _06 (65 W) 5 5 5 5 5 See Table 29 and Figure 15 NOTES: 1. Specification is at 36 °C TC and minimum voltage loadline. Specification is ensured by design characterization and not 100% tested. 2. Specification is at 34 °C TC and minimum voltage loadline. Specification is ensured by design characterization and not 100% tested. 3. Thermal Design Power (TDP) should be used for processor thermal solution design targets. The TDP is not the maximum power that the processor can dissipate. 4. This table shows the maximum TDP for a given frequency range. Individual processors may have a lower TDP. Therefore, the maximum TC will vary depending on the TDP of the individual processor. Refer to thermal profile figure and associated table for the allowed combinations of power and TC. 5. 775_VR_CONFIG_06 guidelines provide a design target for meeting future thermal requirements. 78 Datasheet Thermal Specifications and Design Considerations Table 28. Figure 14. Intel® Core™2 Duo Processor E8000 Series Thermal Profile Power (W) Maximum Tc (°C) Power (W) Maximum Tc (°C) Power (W) Maximum Tc (°C) 0 45.1 24 55.2 48 65.3 2 45.9 26 56.0 50 66.1 4 46.8 28 56.9 52 66.9 6 47.6 30 57.7 54 67.8 8 48.5 32 58.5 56 68.6 10 49.3 34 59.4 58 69.5 12 50.1 36 60.2 60 70.3 14 51.0 38 61.1 62 71.1 16 51.8 40 61.9 64 72.0 18 52.7 42 62.7 65 72.4 20 53.5 44 63.6 22 54.3 46 64.4 Intel® Core™2 Duo Processor E8000 Series Thermal Profile 72.0 68.0 64.0 Tcase (C) y = 0.42x + 45.1 60.0 56.0 52.0 48.0 44.0 0 10 20 30 40 50 60 Power (W) Datasheet 79 Thermal Specifications and Design Considerations Table 29. Figure 15. Intel® Core™2 Duo Processor E7000 Series Thermal Profile Power (W) Maximum Tc (°C) Power Maximum Tc (°C) Power Maximum Tc (°C) 0 44.9 24 55.7 48 66.5 2 45.8 26 56.6 50 67.4 4 46.7 28 57.5 52 68.3 6 47.6 30 58.4 54 69.2 8 48.5 32 59.3 56 70.1 10 49.4 34 60.2 58 71.0 12 50.3 36 61.1 60 71.9 14 51.2 38 62.0 62 72.8 16 52.1 40 62.9 64 73.7 18 53.0 42 63.8 65 74.1 20 53.9 44 64.7 22 54.8 46 65.6 Intel® Core™2 Duo Processor E7000 Series Thermal Profile 72.0 68.0 64.0 Tcase (C) y = 0.45x + 44.9 60.0 56.0 52.0 48.0 44.0 0 10 20 30 40 50 60 Power (W) 80 Datasheet Thermal Specifications and Design Considerations 5.1.2 Thermal Metrology The maximum and minimum case temperatures (TC) for the processor is specified in Table 27. This temperature specification is meant to help ensure proper operation of the processor. Figure 16 illustrates where Intel recommends TC thermal measurements should be made. For detailed guidelines on temperature measurement methodology, refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2). Figure 16. Case Temperature (TC) Measurement Location 37.5 mm Measure TC at this point (geometric center of the package) 37.5 mm 5.2 Processor Thermal Features 5.2.1 Thermal Monitor The Thermal Monitor feature helps control the processor temperature by activating the thermal control circuit (TCC) when the processor silicon reaches its maximum operating temperature. The TCC reduces processor power consumption by modulating (starting and stopping) the internal processor core clocks. The Thermal Monitor feature must be enabled for the processor to be operating within specifications. The temperature at which Thermal Monitor activates the thermal control circuit is not user configurable and is not software visible. Bus traffic is snooped in the normal manner, and interrupt requests are latched (and serviced during the time that the clocks are on) while the TCC is active. When the Thermal Monitor feature is enabled, and a high temperature situation exists (i.e., TCC is active), the clocks will be modulated by alternately turning the clocks off and on at a duty cycle specific to the processor (typically 30–50%). Clocks often will not be off for more than 3.0 microseconds when the TCC is active. Cycle times are processor speed dependent and will decrease as processor core frequencies increase. A small amount of hysteresis has been included to prevent rapid active/inactive transitions of the TCC when the processor temperature is near its maximum operating temperature. Once the temperature has dropped below the maximum operating temperature, and the hysteresis timer has expired, the TCC goes inactive and clock modulation ceases. With a properly designed and characterized thermal solution, it is anticipated that the TCC would only be activated for very short periods of time when running the most power intensive applications. The processor performance impact due to these brief Datasheet 81 Thermal Specifications and Design Considerations periods of TCC activation is expected to be so minor that it would be immeasurable. An under-designed thermal solution that is not able to prevent excessive activation of the TCC in the anticipated ambient environment may cause a noticeable performance loss, and in some cases may result in a TC that exceeds the specified maximum temperature and may affect the long-term reliability of the processor. In addition, a thermal solution that is significantly under-designed may not be capable of cooling the processor even when the TCC is active continuously. Refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2) for information on designing a thermal solution. The duty cycle for the TCC, when activated by the Thermal Monitor, is factory configured and cannot be modified. The Thermal Monitor does not require any additional hardware, software drivers, or interrupt handling routines. 5.2.2 Thermal Monitor 2 The processor also supports an additional power reduction capability known as Thermal Monitor 2. This mechanism provides an efficient means for limiting the processor temperature by reducing the power consumption within the processor. When Thermal Monitor 2 is enabled, and a high temperature situation is detected, the Thermal Control Circuit (TCC) will be activated. The TCC causes the processor to adjust its operating frequency (using the bus multiplier) and input voltage (using the VID signals). This combination of reduced frequency and VID results in a reduction to the processor power consumption. A processor enabled for Thermal Monitor 2 includes two operating points, each consisting of a specific operating frequency and voltage. The first operating point represents the normal operating condition for the processor. Under this condition, the core-frequency-to-FSB multiple used by the processor is that contained in the CLK_GEYSIII_STAT MSR and the VID is that specified in Table 4. These parameters represent normal system operation. The second operating point consists of both a lower operating frequency and voltage. When the TCC is activated, the processor automatically transitions to the new frequency. This transition occurs very rapidly (on the order of 5 μs). During the frequency transition, the processor is unable to service any bus requests, and consequently, all bus traffic is blocked. Edge-triggered interrupts will be latched and kept pending until the processor resumes operation at the new frequency. Once the new operating frequency is engaged, the processor will transition to the new core operating voltage by issuing a new VID code to the voltage regulator. The voltage regulator must support dynamic VID steps in order to support Thermal Monitor 2. During the voltage change, it will be necessary to transition through multiple VID codes to reach the target operating voltage. Each step will likely be one VID table entry (see Table 4). The processor continues to execute instructions during the voltage transition. Operation at the lower voltage reduces the power consumption of the processor. A small amount of hysteresis has been included to prevent rapid active/inactive transitions of the TCC when the processor temperature is near its maximum operating temperature. Once the temperature has dropped below the maximum operating temperature, and the hysteresis timer has expired, the operating frequency and voltage transition back to the normal system operating point. Transition of the VID code will occur first, in order to ensure proper operation once the processor reaches its normal operating frequency. Refer to Figure 17 for an illustration of this ordering. 82 Datasheet Thermal Specifications and Design Considerations Figure 17. Thermal Monitor 2 Frequency and Voltage Ordering TTM2 Temperature fMAX fTM2 Frequency VID VIDTM2 VID PROCHOT# The PROCHOT# signal is asserted when a high temperature situation is detected, regardless of whether Thermal Monitor or Thermal Monitor 2 is enabled. It should be noted that the Thermal Monitor 2 TCC cannot be activated using the ondemand mode. The Thermal Monitor TCC, however, can be activated through the use of the on-demand mode. 5.2.3 On-Demand Mode The processor provides an auxiliary mechanism that allows system software to force the processor to reduce its power consumption. This mechanism is referred to as “OnDemand” mode and is distinct from the Thermal Monitor feature. On-Demand mode is intended as a means to reduce system level power consumption. Systems using the processor must not rely on software usage of this mechanism to limit the processor temperature. If bit 4 of the ACPI P_CNT Control Register (located in the processor IA32_THERM_CONTROL MSR) is written to a '1', the processor will immediately reduce its power consumption using modulation (starting and stopping) of the internal core clock, independent of the processor temperature. When using On-Demand mode, the duty cycle of the clock modulation is programmable using bits 3:1 of the same ACPI P_CNT Control Register. In On-Demand mode, the duty cycle can be programmed from 12.5% on/87.5% off, to 87.5% on/12.5% off in 12.5% increments. On-Demand mode may be used in conjunction with the Thermal Monitor. If the system tries to enable OnDemand mode at the same time the TCC is engaged, the factory configured duty cycle of the TCC will override the duty cycle selected by the On-Demand mode. Datasheet 83 Thermal Specifications and Design Considerations 5.2.4 PROCHOT# Signal An external signal, PROCHOT# (processor hot), is asserted when the processor core temperature has reached its maximum operating temperature. If the Thermal Monitor is enabled (note that the Thermal Monitor must be enabled for the processor to be operating within specification), the TCC will be active when PROCHOT# is asserted. The processor can be configured to generate an interrupt upon the assertion or deassertion of PROCHOT#. PROCHOT# is a bi-directional signal. As an output, PROCHOT# (Processor Hot) will go active when the processor temperature monitoring sensor detects that one or both cores has reached its maximum safe operating temperature. This indicates that the processor Thermal Control Circuit (TCC) has been activated, if enabled. As an input, assertion of PROCHOT# by the system will activate the TCC, if enabled, for both cores. The TCC will remain active until the system de-asserts PROCHOT#. Note: PROCHOT# will not be asserted (as an output) or observed (as an input) when the processor is in the Stop Grant, Sleep, Deep Sleep, and Deeper Sleep low-power states, hence the thermal solution must be designed to ensure the processor remains within specification. If the processor enters one of the above low-power states with PROCHOT# already asserted, PROCHOT# will remain asserted until the processor exits the low-power state and the processor DTS temperature drops below the thermal trip point. PROCHOT# allows for some protection of various components from over-temperature situations. The PROCHOT# signal is bi-directional in that it can either signal when the processor (either core) has reached its maximum operating temperature or be driven from an external source to activate the TCC. The ability to activate the TCC using PROCHOT# can provide a means for thermal protection of system components. Bi-directional PROCHOT# can allow VR thermal designs to target maximum sustained current instead of maximum current. Systems should still provide proper cooling for the VR, and rely on bi-directional PROCHOT# only as a backup in case of system cooling failure. The system thermal design should allow the power delivery circuitry to operate within its temperature specification even while the processor is operating at its Thermal Design Power. With a properly designed and characterized thermal solution, it is anticipated that bi-directional PROCHOT# would only be asserted for very short periods of time when running the most power intensive applications. An under-designed thermal solution that is not able to prevent excessive assertion of PROCHOT# in the anticipated ambient environment may cause a noticeable performance loss. Refer to the Voltage Regulator Design Guide for details on implementing the bi-directional PROCHOT# feature. 5.2.5 THERMTRIP# Signal Regardless of whether or not Thermal Monitor or Thermal Monitor 2 is enabled, in the event of a catastrophic cooling failure, the processor will automatically shut down when the silicon has reached an elevated temperature (refer to the THERMTRIP# definition in Table 26). At this point, the FSB signal THERMTRIP# will go active and stay active as described in Table 26. THERMTRIP# activation is independent of processor activity and does not generate any bus cycles. If THERMTRIP# is asserted, processor core voltage (VCC) must be removed within the timeframe defined in Table 11. 84 Datasheet Thermal Specifications and Design Considerations 5.3 Platform Environment Control Interface (PECI) 5.3.1 Introduction PECI offers an interface for thermal monitoring of Intel processor and chipset components. It uses a single wire, thus alleviating routing congestion issues. PECI uses CRC checking on the host side to ensure reliable transfers between the host and client devices. Also, data transfer speeds across the PECI interface are negotiable within a wide range (2 Kbps to 2 Mbps). The PECI interface on the processor is disabled by default and must be enabled through BIOS. More information can be found in the Platform Environment Control Interface (PECI) Specification. 5.3.1.1 TCONTROL and TCC activation on PECI-Based Systems Fan speed control solutions based on PECI utilize a TCONTROL value stored in the processor IA32_TEMPERATURE_TARGET MSR. The TCONTROL MSR uses the same offset temperature format as PECI though it contains no sign bit. Thermal management devices should infer the TCONTROL value as negative. Thermal management algorithms should utilize the relative temperature value delivered over PECI in conjunction with the TCONTROL MSR value to control or optimize fan speeds. Figure 18 shows a conceptual fan control diagram using PECI temperatures. The relative temperature value reported over PECI represents the delta below the onset of thermal control circuit (TCC) activation as indicated by PROCHOT# assertions. As the temperature approaches TCC activation, the PECI value approaches zero. TCC activates at a PECI count of zero. Figure 18. Datasheet Conceptual Fan Control Diagram on PECI-Based Platforms 85 Thermal Specifications and Design Considerations 5.3.2 PECI Specifications 5.3.2.1 PECI Device Address The PECI register resides at address 30h. 5.3.2.2 PECI Command Support PECI command support is covered in detail in the Platform Environment Control Interface Specification. Refer to this document for details on supported PECI command function and codes. 5.3.2.3 PECI Fault Handling Requirements PECI is largely a fault tolerant interface, including noise immunity and error checking improvements over other comparable industry standard interfaces. The PECI client is as reliable as the device that it is embedded in, and thus given operating conditions that fall under the specification, the PECI will always respond to requests and the protocol itself can be relied upon to detect any transmission failures. There are, however, certain scenarios where the PECI is know to be unresponsive. Prior to a power-on RESET# and during RESET# assertion, PECI is not assured to provide reliable thermal data. System designs should implement a default power-on condition that ensures proper processor operation during the time frame when reliable data is not available using PECI. To protect platforms from potential operational or safety issues due to an abnormal condition on PECI, the Host controller should take action to protect the system from possible damage. It is recommended that the PECI host controller take appropriate action to protect the client processor device if valid temperature readings have not been obtained in response to three consecutive GetTemp()s or for a one second time interval. The host controller may also implement an alert to software in the event of a critical or continuous fault condition. 5.3.2.4 PECI GetTemp0() Error Code Support The error codes supported for the processor GetTemp() command are listed in Table 30: Table 30. GetTemp0() Error Codes Error Code Description 8000h General sensor error 8002h Sensor is operational, but has detected a temperature below its operational range (underflow) §§ 86 Datasheet Features 6 Features 6.1 Power-On Configuration Options Several configuration options can be configured by hardware. The processor samples the hardware configuration at reset, on the active-to-inactive transition of RESET#. For specifications on these options, refer to Table 31. The sampled information configures the processor for subsequent operation. These configuration options cannot be changed except by another reset. All resets reconfigure the processor; for configuration purposes, the processor does not distinguish between a "warm" reset and a "power-on" reset. Table 31. Power-On Configuration Option Signals Configuration Option Output tristate Execute BIST Signal1,2 SMI# A3# Disable dynamic bus parking A25# Symmetric agent arbitration ID BR0# RESERVED A[24:4]#, A[35:26]# NOTE: 1. Asserting this signal during RESET# will select the corresponding option. 2. Address signals not identified in this table as configuration options should not be asserted during RESET#. 3. Disabling of any of the cores within the processors must be handled by configuring the EXT_CONFIG Model Specific Register (MSR). This MSR will allow for the disabling of a single core per die within the processor package. 6.2 Clock Control and Low Power States The processor allows the use of AutoHALT and Stop-Grant states to reduce power consumption by stopping the clock to internal sections of the processor, depending on each particular state. See Figure 19 for a visual representation of the processor low power states. Datasheet 87 Features Figure 19. Processor Low Power State Machine HALT or MWAIT Instruction and HALT Bus Cycle Generated Normal State - Normal Execution STPCLK# Asserted INIT#, INTR, NMI, SMI#, RESET#, FSB interrupts Extended HALT or HALT State - BCLK running - Snoops and interrupts allowed Snoop Event Occurs STPCLK# De-asserted STPCLK# Asserted Snoop Event Serviced STPCLK# De-asserted Extended HALT Snoop or HALT Snoop State - BCLK running - Service Snoops to caches Stop Grant State - BCLK running - Snoops and interrupts allowed SLP# Asserted Extended Stop Grant or Stop Grant Snoop State - BCLK running - Service Snoops to caches Snoop Event Serviced SLP# De-asserted Sleep State - BCLK running - No Snoops or interrupts allowed - PECI unavailable in this state 6.2.1 Snoop Event Occurs DPSLP# Asserted DPSLP# De-asserted Deep Sleep State - BCLK can be stopped - No Snoops or interrupts allowed - PECI unavailable in this state DPRSTP# Asserted DPRSTP# De-asserted Deeper Sleep State - BCLK can be stopped - No Snoops or interrupts allowed - PECI unavailable in this state Normal State This is the normal operating state for the processor. 6.2.2 HALT and Extended HALT Powerdown States The processor supports the HALT or Extended HALT powerdown state. The Extended HALT powerdown state must be configured and enabled using the BIOS for the processor to remain within specification. The Extended HALT state is a lower power state as compared to the Stop Grant State. If Extended HALT is not enabled, the default powerdown state entered will be HALT. Refer to the sections below for details about the HALT and Extended HALT states. 6.2.2.1 HALT Powerdown State HALT is a low power state entered when all the processor cores have executed the HALT or MWAIT instructions. When one of the processor cores executes the HALT instruction, that processor core is halted, however, the other processor continues normal operation. The halted core will transition to the Normal state upon the occurrence of SMI#, INIT#, or LINT[1:0] (NMI, INTR). RESET# will cause the processor to immediately initialize itself. 88 Datasheet Features The return from a System Management Interrupt (SMI) handler can be to either Normal Mode or the HALT powerdown state. See the Intel Architecture Software Developer's Manual, Volume 3B: System Programming Guide, Part 2 for more information. The system can generate a STPCLK# while the processor is in the HALT powerdown state. When the system de-asserts the STPCLK# interrupt, the processor will return execution to the HALT state. While in HALT powerdown state, the processor will process bus snoops. 6.2.2.2 Extended HALT Powerdown State Extended HALT is a low power state entered when all processor cores have executed the HALT or MWAIT instructions and Extended HALT has been enabled using the BIOS. When one of the processor cores executes the HALT instruction, that logical processor is halted; however, the other processor continues normal operation. The Extended HALT powerdown state must be enabled using the BIOS for the processor to remain within its specification. The processor will automatically transition to a lower frequency and voltage operating point before entering the Extended HALT state. Note that the processor FSB frequency is not altered; only the internal core frequency is changed. When entering the low power state, the processor will first switch to the lower bus ratio and then transition to the lower VID. While in Extended HALT state, the processor will process bus snoops. The processor exits the Extended HALT state when a break event occurs. When the processor exits the Extended HALT state, it will resume operation at the lower frequency, transition the VID to the original value, and then change the bus ratio back to the original value. 6.2.3 Stop Grant and Extended Stop Grant States The processor supports the Stop Grant and Extended Stop Grant states. The Extended Stop Grant state is a feature that must be configured and enabled using the BIOS. Refer to the sections below for details about the Stop Grant and Extended Stop Grant states. 6.2.3.1 Stop-Grant State When the STPCLK# signal is asserted, the Stop Grant state of the processor is entered 20 bus clocks after the response phase of the processor-issued Stop Grant Acknowledge special bus cycle. Since the GTL+ signals receive power from the FSB, these signals should not be driven (allowing the level to return to VTT) for minimum power drawn by the termination resistors in this state. In addition, all other input signals on the FSB should be driven to the inactive state. RESET# will cause the processor to immediately initialize itself, but the processor will stay in Stop-Grant state. A transition back to the Normal state will occur with the deassertion of the STPCLK# signal. A transition to the Grant Snoop state will occur when the processor detects a snoop on the FSB (see Section 6.2.4). While in the Stop-Grant State, SMI#, INIT# and LINT[1:0] will be latched by the processor, and only serviced when the processor returns to the Normal State. Only one occurrence of each event will be recognized upon return to the Normal state. Datasheet 89 Features While in Stop-Grant state, the processor will process a FSB snoop. 6.2.3.2 Extended Stop Grant State Extended Stop Grant is a low power state entered when the STPCLK# signal is asserted and Extended Stop Grant has been enabled using the BIOS. The processor will automatically transition to a lower frequency and voltage operating point before entering the Extended Stop Grant state. When entering the low power state, the processor will first switch to the lower bus ratio and then transition to the lower VID. The processor exits the Extended Stop Grant state when a break event occurs. When the processor exits the Extended Stop Grant state, it will resume operation at the lower frequency, transition the VID to the original value, and then change the bus ratio back to the original value. 6.2.4 Extended HALT Snoop State, HALT Snoop State, Extended Stop Grant Snoop State, and Stop Grant Snoop State The Extended HALT Snoop State is used in conjunction with the Extended HALT state. If Extended HALT state is not enabled in the BIOS, the default Snoop State entered will be the HALT Snoop State. Refer to the sections below for details on HALT Snoop State, Stop Grant Snoop State, Extended HALT Snoop State, Extended Stop Grant Snoop State. 6.2.4.1 HALT Snoop State, Stop Grant Snoop State The processor will respond to snoop transactions on the FSB while in Stop-Grant state or in HALT powerdown state. During a snoop transaction, the processor enters the HALT Snoop State:Stop Grant Snoop state. The processor will stay in this state until the snoop on the FSB has been serviced (whether by the processor or another agent on the FSB). After the snoop is serviced, the processor will return to the Stop Grant state or HALT powerdown state, as appropriate. 6.2.4.2 Extended HALT Snoop State, Extended Stop Grant Snoop State The processor will remain in the lower bus ratio and VID operating point of the Extended HALT state or Extended Stop Grant state. While in the Extended HALT Snoop State or Extended Stop Grant Snoop State, snoops are handled the same way as in the HALT Snoop State or Stop Grant Snoop State. After the snoop is serviced the processor will return to the Extended HALT state or Extended Stop Grant state. 6.2.5 Sleep State The Sleep state is a low power state in which the processor maintains its context, maintains the phase-locked loop (PLL), and stops all internal clocks. The Sleep state is entered through assertion of the SLP# signal while in the Extended Stop Grant or Stop Grant state. The SLP# pin should only be asserted when the processor is in the Extended Stop Grant or Stop Grant state. SLP# assertions while the processor is not in these states is out of specification and may result in unapproved operation. In the Sleep state, the processor is incapable of responding to snoop transactions or latching interrupt signals. No transitions or assertions of signals (with the exception of SLP#, DPSLP# or RESET#) are allowed on the FSB while the processor is in Sleep state. Snoop events that occur while in Sleep state or during a transition into or out of 90 Datasheet Features Sleep state will cause unpredictable behavior. Any transition on an input signal before the processor has returned to the Stop-Grant state will result in unpredictable behavior.If RESET# is driven active while the processor is in the Sleep state, and held active as specified in the RESET# pin specification, then the processor will reset itself, ignoring the transition through the Stop-Grant state. If RESET# is driven active while the processor is in the Sleep state, the SLP# and STPCLK# signals should be de-asserted immediately after RESET# is asserted to ensure the processor correctly executes the Reset sequence. While in the Sleep state, the processor is capable of entering an even lower power state, the Deep Sleep state, by asserting the DPSLP# pin (See Section Section 6.2.6). While the processor is in the Sleep state, the SLP# pin must be de-asserted if another asynchronous FSB event needs to occur. PECI is not available and will not respond while in the Sleep State. Refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2) for guidance on how to ensure PECI thermal data is available when the Sleep State is enabled. 6.2.6 Deep Sleep State The Deep Sleep state is entered through assertion of the DPSLP# pin while in the Sleep state. BCLK may be stopped during the Deep Sleep state for additional platform level power savings. BCLK stop/restart timings on appropriate chipset-based platforms with the CK505 clock chip are as follows: • Deep Sleep entry: the system clock chip may stop/tristate BCLK within two BCLKs of DPSLP# assertion. It is permissible to leave BCLK running during Deep Sleep. • Deep Sleep exit: the system clock chip must drive BCLK to differential DC levels within 2-3 ns of DPSLP# de-assertion and start toggling BCLK within 10 BCLK periods. To re-enter the Sleep state, the DPSLP# pin must be de-asserted. BCLK can be restarted after DPSLP# de-assertion as described above. A period of 15 microseconds (to allow for PLL stabilization) must occur before the processor can be considered to be in the Sleep state. Once in the Sleep state, the SLP# pin must be de-asserted to reenter the Stop-Grant state. While in the Deep Sleep state the processor is incapable of responding to snoop transactions or latching interrupt signals. No transitions of signals are allowed on the FSB while the processor is in the Deep Sleep state. When the processor is in the Deep Sleep state it will not respond to interrupts or snoop transactions. Any transition on an input signal before the processor has returned to the Stop-Grant state will result in unpredictable behavior. PECI is not available and will not respond while in the Deep Sleep State. Refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2) for guidance on how to ensure PECI thermal data is available when the Deep Sleep State is enabled. 6.2.7 Deeper Sleep State The Deeper Sleep state is similar to the Deep Sleep state but the core voltage is reduced to a lower level. The Deeper Sleep state is entered through assertion of the DPRSTP# pin while in the Deep Sleep state. Exit from Deeper Sleep is initiated by DPRSTP# de-assertion. PECI is not available and will not respond while in the Deeper Sleep State. Refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2) for guidance on how to ensure PECI thermal data is available when the Deeper Sleep State is enabled. Datasheet 91 Features In response to entering Deeper Sleep, the processor drives the VID code corresponding to the Deeper Sleep core voltage on the VID pins. Unlike typical Dynamic VID changes (where the steps are single VID steps) the processor will perform a VID jump on the order of 100 mV. To support the Deeper Sleep State the platform must use a VRD 11.1 compliant solution. 6.2.8 Enhanced Intel SpeedStep® Technology The processor supports Enhanced Intel SpeedStep Technology. This technology enables the processor to switch between frequency and voltage points, which may result in platform power savings. To support this technology, the system must support dynamic VID transitions. Switching between voltage/frequency states is software controlled. Enhanced Intel SpeedStep Technology is a technology that creates processor performance states (P states). P states are power consumption and capability states within the Normal state as shown in Figure 19. Enhanced Intel SpeedStep Technology enables real-time dynamic switching between frequency and voltage points. It alters the performance of the processor by changing the bus to core frequency ratio and voltage. This allows the processor to run at different core frequencies and voltages to best serve the performance and power requirements of the processor and system. Note that the front side bus is not altered; only the internal core frequency is changed. In order to run at reduced power consumption, the voltage is altered in step with the bus ratio. The following are key features of Enhanced Intel SpeedStep Technology: • Voltage/Frequency selection is software controlled by writing to processor MSR's (Model Specific Registers), thus eliminating chipset dependency. — If the target frequency is higher than the current frequency, Vcc is incriminated in steps (+12.5 mV) by placing a new value on the VID signals after which the processor shifts to the new frequency. Note that the top frequency for the processor can not be exceeded. — If the target frequency is lower than the current frequency, the processor shifts to the new frequency and Vcc is then decremented in steps (-12.5 mV) by changing the target VID through the VID signals. 6.3 Processor Power Status Indicator (PSI) Signal The processor incorporates the PSI# signal that is asserted when the processor is in a reduced power consumption state. PSI# can be used to improve efficiency of the voltage regulator, resulting in platform power savings. PSI# may be asserted only when the processor is in the Deeper Sleep state. § 92 Datasheet Boxed Processor Specifications 7 Boxed Processor Specifications 7.1 Introduction The processor will also be offered as an Intel boxed processor. Intel boxed processors are intended for system integrators who build systems from baseboards and standard components. The boxed processor will be supplied with a cooling solution. This chapter documents baseboard and system requirements for the cooling solution that will be supplied with the boxed processor. This chapter is particularly important for OEMs that manufacture baseboards for system integrators. Note: Unless otherwise noted, all figures in this chapter are dimensioned in millimeters and inches [in brackets]. Figure 20 shows a mechanical representation of a boxed processor. Note: Drawings in this section reflect only the specifications on the Intel boxed processor product. These dimensions should not be used as a generic keep-out zone for all cooling solutions. It is the system designers’ responsibility to consider their proprietary cooling solution when designing to the required keep-out zone on their system platforms and chassis. Refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2) for further guidance. Contact your local Intel Sales Representative for this document. Figure 20. Mechanical Representation of the Boxed Processor NOTE: The airflow of the fan heatsink is into the center and out of the sides of the fan heatsink. Datasheet 93 Boxed Processor Specifications 7.2 Mechanical Specifications 7.2.1 Boxed Processor Cooling Solution Dimensions This section documents the mechanical specifications of the boxed processor. The boxed processor will be shipped with an unattached fan heatsink. Figure 20 shows a mechanical representation of the boxed processor. Clearance is required around the fan heatsink to ensure unimpeded airflow for proper cooling. The physical space requirements and dimensions for the boxed processor with assembled fan heatsink are shown in Figure 21 (Side View), and Figure 22 (Top View). The airspace requirements for the boxed processor fan heatsink must also be incorporated into new baseboard and system designs. Airspace requirements are shown in Figure 26 and Figure 27. Note that some figures have centerlines shown (marked with alphabetic designations) to clarify relative dimensioning. Figure 21. Space Requirements for the Boxed Processor (Side View) 95.0 [3.74] 81.3 [3.2] 10.0 [0.39] 25.0 [0.98] B Figure 22. d P Sid Vi Space Requirements for the Boxed Processor (Top View) 95.0 [3.74] 95.0 [3.74] NOTES: 1. Diagram does not show the attached hardware for the clip design and is provided only as a mechanical representation. 94 Datasheet Boxed Processor Specifications Figure 23. Overall View Space Requirements for the Boxed Processor 7.2.2 Boxed Processor Fan Heatsink Weight The boxed processor fan heatsink will not weigh more than 450 grams. See Chapter 5 and the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2) for details on the processor weight and heatsink requirements. 7.2.3 Boxed Processor Retention Mechanism and Heatsink Attach Clip Assembly The boxed processor thermal solution requires a heatsink attach clip assembly, to secure the processor and fan heatsink in the baseboard socket. The boxed processor will ship with the heatsink attach clip assembly. 7.3 Electrical Requirements 7.3.1 Fan Heatsink Power Supply The boxed processor's fan heatsink requires a +12 V power supply. A fan power cable will be shipped with the boxed processor to draw power from a power header on the baseboard. The power cable connector and pinout are shown in Figure 24. Baseboards must provide a matched power header to support the boxed processor. Table 32 contains specifications for the input and output signals at the fan heatsink connector. The fan heatsink outputs a SENSE signal, which is an open- collector output that pulses at a rate of 2 pulses per fan revolution. A baseboard pull-up resistor provides VOH to match the system board-mounted fan speed monitor requirements, if applicable. Use of the SENSE signal is optional. If the SENSE signal is not used, pin 3 of the connector should be tied to GND. The fan heatsink receives a PWM signal from the motherboard from the 4th pin of the connector labeled as CONTROL. Datasheet 95 Boxed Processor Specifications The boxed processor's fanheat sink requires a constant +12 V supplied to pin 2 and does not support variable voltage control or 3-pin PWM control. The power header on the baseboard must be positioned to allow the fan heatsink power cable to reach it. The power header identification and location should be documented in the platform documentation, or on the system board itself. Figure 25 shows the location of the fan power connector relative to the processor socket. The baseboard power header should be positioned within 110 mm [4.33 inches] from the center of the processor socket. Figure 24. Boxed Processor Fan Heatsink Power Cable Connector Description Pin 1 2 3 4 Signal GND +12 V SENSE CONTROL Straight square pin, 4-pin terminal housing with polarizing ribs and friction locking ramp. 0.100" pitch, 0.025" square pin width. Match with straight pin, friction lock header on mainboard. 1 2 3 4 Table 32. Fan Heatsink Power and Signal Specifications Description Min Typ Max Unit Notes 11.4 12 12.6 V - • Maximum fan steady-state current draw — 1.2 — A • Average fan steady-state current draw — 0.5 — A • Maximum fan start-up current draw — 2.2 — A • Fan start-up current draw maximum duration — 1.0 — Second SENSE: SENSE frequency — 2 — pulses per fan revolution 1 CONTROL 21 25 28 kHz 2, 3 +12 V: 12 volt fan power supply IC: - NOTES: 1. Baseboard should pull this pin up to 5 V with a resistor. 2. Open drain type, pulse width modulated. 3. Fan will have pull-up resistor for this signal to maximum of 5.25 V. 96 Datasheet Boxed Processor Specifications Figure 25. Baseboard Power Header Placement Relative to Processor Socket B R110 [4.33] C 7.4 Thermal Specifications This section describes the cooling requirements of the fan heatsink solution used by the boxed processor. 7.4.1 Boxed Processor Cooling Requirements The boxed processor may be directly cooled with a fan heatsink. However, meeting the processor's temperature specification is also a function of the thermal design of the entire system, and ultimately the responsibility of the system integrator. The processor temperature specification is provided in Chapter 5. The boxed processor fan heatsink is able to keep the processor temperature within the specifications (see Table 27) in chassis that provide good thermal management. For the boxed processor fan heatsink to operate properly, it is critical that the airflow provided to the fan heatsink is unimpeded. Airflow of the fan heatsink is into the center and out of the sides of the fan heatsink. Airspace is required around the fan to ensure that the airflow through the fan heatsink is not blocked. Blocking the airflow to the fan heatsink reduces the cooling efficiency and decreases fan life. Figure 26 and Figure 27 illustrate an acceptable airspace clearance for the fan heatsink. The air temperature entering the fan should be kept below 38 ºC. Again, meeting the processor's temperature specification is the responsibility of the system integrator. Datasheet 97 Boxed Processor Specifications Figure 26. Boxed Processor Fan Heatsink Airspace Keepout Requirements (side 1 view) Figure 27. Boxed Processor Fan Heatsink Airspace Keepout Requirements (side 2 view) 98 Datasheet Boxed Processor Specifications 7.4.2 Variable Speed Fan If the boxed processor fan heatsink 4-pin connector is connected to a 3-pin motherboard header it will operate as follows: The boxed processor fan will operate at different speeds over a short range of internal chassis temperatures. This allows the processor fan to operate at a lower speed and noise level, while internal chassis temperatures are low. If internal chassis temperature increases beyond a lower set point, the fan speed will rise linearly with the internal temperature until the higher set point is reached. At that point, the fan speed is at its maximum. As fan speed increases, so does fan noise levels. Systems should be designed to provide adequate air around the boxed processor fan heatsink that remains cooler then lower set point. These set points, represented in Figure 28 and Table 33, can vary by a few degrees from fan heatsink to fan heatsink. The internal chassis temperature should be kept below 38 ºC. Meeting the processor's temperature specification (see Chapter 5) is the responsibility of the system integrator. The motherboard must supply a constant +12 V to the processor's power header to ensure proper operation of the variable speed fan for the boxed processor. Refer to Table 32 for the specific requirements. Figure 28. Boxed Processor Fan Heatsink Set Points Higher Set Point Highest Noise Level Increasing Fan Speed & Noise Lower Set Point Lowest Noise Level X Y Z Internal Chassis Temperature (Degrees C) Datasheet 99 Boxed Processor Specifications Table 33. Fan Heatsink Power and Signal Specifications Boxed Processor Fan Heatsink Set Point (°C) Boxed Processor Fan Speed Notes X ≤ 30 When the internal chassis temperature is below or equal to this set point, the fan operates at its lowest speed. Recommended maximum internal chassis temperature for nominal operating environment. 1 Y = 35 When the internal chassis temperature is at this point, the fan operates between its lowest and highest speeds. Recommended maximum internal chassis temperature for worst-case operating environment. - Z ≥ 38 When the internal chassis temperature is above or equal to this set point, the fan operates at its highest speed. - NOTES: 1. Set point variance is approximately ± 1 °C from fan heatsink to fan heatsink. If the boxed processor fan heatsink 4-pin connector is connected to a 4-pin motherboard header and the motherboard is designed with a fan speed controller with PWM output (CONTROL see Table 32) and remote thermal diode measurement capability the boxed processor will operate as follows: As processor power has increased the required thermal solutions have generated increasingly more noise. Intel has added an option to the boxed processor that allows system integrators to have a quieter system in the most common usage. The 4th wire PWM solution provides better control over chassis acoustics. This is achieved by more accurate measurement of processor die temperature through the processor's Digital Thermal Sensors (DTS) and PECI. Fan RPM is modulated through the use of an ASIC located on the motherboard that sends out a PWM control signal to the 4th pin of the connector labeled as CONTROL. The fan speed is based on actual processor temperature instead of internal ambient chassis temperatures. If the new 4-pin active fan heat sink solution is connected to an older 3-pin baseboard processor fan header, it will default back to a thermistor controlled mode, allowing compatibility with existing 3-pin baseboard designs. Under thermistor controlled mode, the fan RPM is automatically varied based on the Tinlet temperature measured by a thermistor located at the fan inlet. For more details on specific motherboard requirements for 4-wire based fan speed control, refer to the appropriate Thermal and Mechanical Design Guidelines (see Section 1.2). § 100 Datasheet Debug Tools Specifications 8 Debug Tools Specifications 8.1 Logic Analyzer Interface (LAI) Intel is working with two logic analyzer vendors to provide logic analyzer interfaces (LAIs) for use in debugging Intel Core™2 Duo processor E8000 and E7000 series systems. Tektronix and Agilent should be contacted to get specific information about their logic analyzer interfaces. The following information is general in nature. Specific information must be obtained from the logic analyzer vendor. Due to the complexity of Intel Core™2 Duo processor E8000 and E7000 series systems, the LAI is critical in providing the ability to probe and capture FSB signals. There are two sets of considerations to keep in mind when designing an Intel Core™2 Duo processor E8000 and E7000 series system that can make use of an LAI: mechanical and electrical. 8.1.1 Mechanical Considerations The LAI is installed between the processor socket and the processor. The LAI lands plug into the processor socket, while the processor lands plug into a socket on the LAI. Cabling that is part of the LAI egresses the system to allow an electrical connection between the processor and a logic analyzer. The maximum volume occupied by the LAI, known as the keepout volume, as well as the cable egress restrictions, should be obtained from the logic analyzer vendor. System designers must make sure that the keepout volume remains unobstructed inside the system. Note that it is possible that the keepout volume reserved for the LAI may differ from the space normally occupied by the processor heatsink. If this is the case, the logic analyzer vendor will provide a cooling solution as part of the LAI. 8.1.2 Electrical Considerations The LAI will also affect the electrical performance of the FSB; therefore, it is critical to obtain electrical load models from each of the logic analyzers to be able to run system level simulations to prove that their tool will work in the system. Contact the logic analyzer vendor for electrical specifications and load models for the LAI solution it provides. § Datasheet 101 Debug Tools Specifications 102 Datasheet