MICROSEMI LXMG1612-12-01

LXMG1612-12-xx
®
TM
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
P RODUCTION D ATASHEET
KEY FEATURES
DESCRIPTION
Input Voltage Range: The modules
convert DC voltage from the system
battery or AC adapter directly to highfrequency, high-voltage waves required
to ignite and operate CCFL lamps. A 5V
input inverter is also available
(LXMG1612-05-xx).
Direct Drive Technology: The module
design is based on a new Direct Drive
topology, which provides a number of
cost and performance advantages.
Additional Features: Other benefits of
this new topology are fixed-frequency
operation and secondary-side strikevoltage regulation and all LXMG161212-xx modules feature both open and
shorted lamp protection.
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
Protected by U.S. Patents: 5,923,129; 5,930,121; Patents Pending
PRODUCT HIGHLIGHT
ƒ RangeMAX Wide Range
Dimming
ƒ 9.6V to 14.4V Input Voltage
ƒ Fully Integrated Direct Drive
And Dimming Control
ƒ Single Sided PCB Layout
ƒ Easy To Use Brightness
Control
ƒ MicroAmp SLEEP Mode
ƒ Output Short-Circuit Protection
And Automatic Strike-Voltage
Regulation
ƒ Fixed Frequency Operation
ƒ UL 60950 E175910
ƒ RoHS Compliant
WWW . Microsemi .C OM
RangeMAX Wide Range Dimming,
Single
Output
Inverter.
The
LXMG1612-12-xx series of Direct
Drive™
CCFL
(Cold
Cathode
Fluorescent Lamp) Inverter Modules are
specifically de-signed for driving LCD
backlight lamps.
RangeMAX
Digital
Dimming
Technique. Digital Dimming provides
flicker-free brightness control in any
wide-range dimming application.
The modules are equipped with a
dimming input that permits brightness
control from an external potentiometer,
DC voltage source, or PWM signal. The
resultant “burst drive” that energizes the
lamp was designed specifically to ensure
that no premature lamp degradation
occurs.
APPLICATIONS
ƒ Notebook And Sub-Notebook
Computers
ƒ Portable Instrumentation
ƒ Desktop Displays
ƒ Low Ambient Light Conditions
(i.e. Aircraft Cabins,
Automobile)
BENEFITS
Potentiometer
PWM
Signal
2
3
BRITE
Microsemi
1
DC Voltage
Source
W
UNIVERSAL DIMMING INPUT
ƒ Smooth, Flicker Free 1-100%
Full-Range Brightness Control
Gives Your Product A High
Quality Image
ƒ Output Open Circuit Voltage
Regulation Minimizes Corona
Discharge For Long Life And
High Reliability
ƒ Power Efficient. “Low
Brightness” Capability Allows
For Advanced Power
Management
PACKAGE ORDER INFO
PART NUMBER
OUTPUT CONNECTOR
INVERTER MATES DIRECTLY TO
PANEL CONNECTORS
LXMG1612-12-01
LXMG1612-12-02
LXMG1612-12-03
JST SM02(8.0)B-BHS-1-TB (LF)(SN) or Yeon Ho 20015WR-05A00
JST SM02B-BHSS-1-TB (LF)(SN)or Yeon Ho 35001WR-02A00
Honda QZ-19-A3MYL #02
BHR-03VS-1
BHSR-02VS-1
Honda QZ-19-3F01
Copyright © 2000
Rev. 1.1, 2007-03-27
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1
LXMG1612-12
"PWM", V DC, OR POTENTIOMETER
LXMG1612-12-xx
®
TM
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
P RODUCTION D ATASHEET
ABSOLUTE MAXIMUM RATINGS (NOTE 1)
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of
specified terminal.
WWW . Microsemi .C OM
Input Signal Voltage (VIN1) ................................................................................................................................. -0.3V to 16V
Output Voltage, no load .........................................................................................................Internally Limited to 1800VRMS
Output Current ........................................................................................................................ 8.0mARMS (Internally Limited)
Output Power .................................................................................................................................................................. 6.0W
Input Signal Voltage (BRITE Input) .................................................................................................................. -0.3V to 5.5V
Input Signal Voltage ( SLEEP , VSYNC Inputs)..................................................................................................... -0.3V to 5.5V
Ambient Operating Temperature, zero airflow .....................................................................................................0°C to 70°C
Storage Temperature Range .............................................................................................................................. -40°C to 85°C
FUNCTIONAL PIN DESCRIPTION
CONN
PIN
DESCRIPTION
CN1 (Molex 53261-0871) Mates with 51021-0800 housing, 50079-8100 pins
CN-1
CN1-2
CN1-3
CN1-4
CN1-5
VIN1
Main Input Power Supply (9.6V < VIN1 < 14.4V)
GND
Power Supply Return
ON/OFF Control. (2.1V < SLEEP < VIN1 = ON, 0V < SLEEP < 0.8V = OFF, SLEEP Floating=OFF)
SLEEP
CN1-6
BRITE
CN1-7
BRITE RTN
Brightness Control (0.0V to 2.5VDC). 2.5VDC gives maximum lamp current.
CN1-8
VSYNC
Analog Ground. Use for BRITE signal return ONLY.
Vertical Synchronization Input. 2.5 to 5.0V Logic Level. (20Hz < fSYNC < 200Hz)
CN2 for LXMG1612-12-01 and -02 (JST SM02(8.0)B-BHS-1-TB (LF)(SN) | Yeon Ho 20015WR-05A00 or SM02B-BHSS-1-TB
(LF)(SN) | Yeon Ho 35001WR-02A00)
CN2-1
VHI
High voltage connection to high side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
CN2-2
VLO
Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground
CN2 for LXMG1612-12-03 (Honda QZ-19-A3MYL#02)
CN2-3
VHI
High voltage connection to high side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
CN2-1
VLO
Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground
PHYSICAL DIMENSIONS
PACKAGE DATA
LXMG1612-12-XX
4.96in.
126mm
MOUNTING HOLE
3.0mm DIA. ± .08 DIA
X CN1
0.13in.
0.63in.
3.3mm
16mm
0.5in.
CN2
12.7mm
W
GROUNDED MOUNTING HOLE
0.66in.
3.0mm DIA. ± .08 DIA
3.64in.
92.5mm
16.75mm
0.06in.
1.52mm
0.315in.
8.0mm
PCB tolerances ± 0.5mm
Copyright © 2000
Rev. 1.1, 2007-03-27
Warning
High Voltage Present at all
Output Connectors
Weight: 12.5 (g) typ
.
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2
LXMG1612-12-xx
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
®
TM
P RODUCTION D ATASHEET
Parameter
Symbol
Input Supply Voltage Range (Fully Regulated
Lamp Current)
Input Supply Voltage Range (Functional)
Output Power
Brightness Control Input Voltage Range
Lamp Operating Voltage
Lamp Current (Full Brightness)
Operating Ambient Temperature Range
Recommended Operating Conditions
Min
R.C.
Max
VIN1
PO
VBRT_ADJ
VLAMP
IOLAMP
TA
10.8
12
13.2
9.6
12
3.5
2.5
535
5.8
14.4
4.0
5
620
0.0
450
0
Units
V
W
V
VRMS
mARMS
°C
70
WWW . Microsemi .C OM
RECOMMENDED OPERATING CONDITIONS (R.C.)
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, the following specifications apply over the recommended operating conditions and ambient temperature of
25°C except where otherwise noted.
Parameter
`
Min. Average Lamp Current
(Note 2)
Lamp Start Voltage
Operating Frequency
IL(MIN)
VLS
IBRT
Units
VBRT_ADJ=2.5VDC, SLEEP=HIGH,
Burst Duty=100%, VIN1=12VDC
VBRT_ADJ=0VDC, SLEEP =HIGH, Burst Duty=2.0%,
VIN1=12VDC
0°C <TA < 70°C, VIN1 > 9.6VDC
VBRT_ADJ=2.5VDC, SLEEP=HIGH, VIN1=9.6V – 14.4V
5.2
5.8
6.4
0.12
mARMS
mARMS
1500
1650
1800
VRMS
63
68
73
kHz
VBRT_ADJ=0VDC
-685
-728
-775
µADC
VBRT_ADJ=2.5VDC
-260
-282
-305
µADC
2.35
2.40
VDC
Input Voltage for Max. Lamp Current
VBRT_ADJ
IO(LAMP)=100% Duty Cycle
2.30
Input Voltage for Min. Lamp Current
VBRT_ADJ
IO(LAMP)= Minimum Duty Cycle
0.0
SLEEP INPUT
RUN Mode
V SLEEP(HI)
VIN1=12V
1.9
SLEEP Mode
V SLEEP(LO)
VIN1=12V
-5.0
1.9
2.0
VDC
SLEEP=5.0V
SLEEP =0V
390
410
435
µADC
0.0
0.0
0.0
µADC
VSYNCH(HI)
VIN1=12V
1.50
2.5
5.0
VDC
VSYNCH(LO)
VIN1=12V
I SLEEP
VDC
2.1
VIN1
VDC
-3.0
0.0
1.2
VDC
Input Impedance
ZIN
25
27
29
KΩ
Input Frequency
fSYNC
20
200
Hz
10
µADC
POWER CHARACTERISTICS
Sleep Current
IIN(MIN)
VIN1=12VDC, SLEEP=0.0V
0.0
0.5
Note 2: Minimum lamp current required to maintain even light output may vary with display panel.
Average RMS current = (burst duty cycle) x (burst amplitude of 5.8mARMS)
Copyright © 2000
Rev. 1.1, 2007-03-27
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
ELECTRICALS
VSYNC CHARACTERISTICS
Logic High Level
`
LXMG1612-12-xx
Min
Typ
Max
BRITE INPUT
Input Current
`
IL(MAX)
fO
Input Current
`
Test Conditions
OUTPUT PIN CHARACTERISTICS
Full Bright Lamp Current
`
Symbol
LXMG1612-12-xx
®
TM
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
P RODUCTION D ATASHEET
WWW . Microsemi .C OM
HOW RANGEMAX WORKS
LAMP VOLTAGE & LAMP CURRENT – Burst Mode Operation
Figure 2 – 2% Burst Duty Cycle
Figure 1 – 50% Burst Duty Cycle
Rather than using the traditional dimming technique of varying
lamp current magnitude to adjust light output, RangeMAX
inverters use a fixed lamp current value with a duty cycle control
method.
The lamp current burst width can be modulated from 100%
(continuous lamp current) down to a 2% duty cycle, allowing the
lamp to be dimmed to less than 1% of its full brightness.
As can be seen in Trace 4 of Figure 3 photo at right, careful
design consideration was given to controlling lamp start voltage
to softly start current flow. This eliminates current overshoot that
can result in premature cathode wear and reduce lamp life.
Figure 3 – 2% Burst Duty Cycle (Expanded Time Base)
High Voltage
Transformer
Comparator
VBRITE
VHI
+
0.25 2.5V DC
Transformer
Driver
Ramp
DESCRIPTION
LAMP
-
Ramp Gen
VSENSE
VSYNC
ISENSE
VLO
Figure 4 – RangeMAX Block Diagram
Copyright © 2000
Rev. 1.1, 2007-03-27
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 4
LXMG1612-12-xx
®
TM
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
P RODUCTION D ATASHEET
Highlights
ƒ
Integrated brightness control circuit includes a DC voltage to
pulse width converter that minimizes system design work and
system noise susceptibility. This provides a familiar and
convenient interface while reducing the potential for
externally induced noise, which can cause lamp flicker.
ƒ
RangeMAX inverter modules are designed to operate with the
burst frequency synchronized to the video frame rate. This
provides operation with no visible display disturbances
caused by beat frequencies between the lamps and video
frame rates. In this synchronous mode, the inverter burst rate
operates at twice the video refresh rate, well beyond standard
50/60Hz video refresh rates where the eye can perceive
pulsing light.
ƒ
In applications with no access to a vertical sync., an onboard
oscillator operates the inverter burst rate at about 250Hz. In
this non-synchronous mode, minor display disturbances can
be found under certain video conditions. This performance
may be acceptable for many applications, but
synchronization must be used when no disturbance can be
tolerated.
ƒ
A single input will accommodate negative and positive
vertical sync pulses at any pulse width.
ƒ
Separate feedback loops for lamp current and open circuit
voltage regulation insure reliable strike under all operating
conditions, automatic over-voltage prevention with broken
or failed lamps, and accurate lamp current regulation.
WWW . Microsemi .C OM
HOW RANGEMAX WORKS (CONTINUED)
TYPICAL APPLICATION
12V
DAC or
Pot
BRITE
V IN1
ƒ
The brightness control may be a voltage output DAC, digital
resistor or a simple 10k potentiometer. If desired, an
additional series resistor with the 10k potentiometer can be
used to set a higher minimum brightness setting as shown in
Figure 5. A 2.5V to 5V Logic Level PWM signal from a
micro-controller may also be used as shown in Figure 5A.
ƒ
If synchronization to the video frame rate is desired, connect
the vertical sync pulse from the system video controller to
the VSYNC input. If no video synchronization is desired,
connect VSYNC to ground.
ƒ
If you need to turn the inverter ON/OFF remotely, connect
to 2.5V to 5V logic signal to the SLEEP input.
ƒ
Connect VHI to high voltage wire from the lamp. Connect
VLO to the low voltage wire (wire with thinner insulation).
Never connect VLO to circuit ground as this will defeat lamp
current regulation. If both lamp wires have heavy high
voltage insulation, connect the longest wire to VLO. This
wire is typically white.
V HI
10k
CCFL
TUBE
LXMG1612-12-xx
R
BRITE RTN
V SYNC
5V
SLEEP
GND
V LO
0V
V SYNC
Figure 5 - Potentiometer Brightness Control
PWM Signal
from System
BRITE
P.W.
LXMG1612-12-xx
< 2ms
0 < P.W. < 100% of period
Figure 5A - PWM Brightness Control
LXMG1612-12-XX OUTPUT CURRENT ADJUST
R4
R40
R17
R36
R39
R37
R38
C16
R11
C8
U1
R5
R35
R32
R31
C6
C21
R14
C12
C5
R41
R15
R12
C15
R2
R20
R7
C11
C4
C7
R16
Not Used
Not Used
Not Used
499K 1%
178K 1%
78.7K 1%
C9
C2
D1
Copyright © 2000
Rev. 1.1, 2007-03-27
R12
2.00K 1%
2.61K 1%
2.74K 1%
2.74K 1%
2.74K 1%
2.74K 1%
R3
C3
U3
R21
Output Current
7.0mA
6.0mA
5.8mA
5.0mA
4.0mA
3.0mA
R34
R6
C14
C13
C10
C17
R33
DESCRIPTION
R30
U4
D2
The LXMG1612-12 output current can be adjusted by changing the
value of two resistors on the PCB. The following table shows the
approximate new output current values:
R16
R10
R13
Figure 6- Component Replacement Locations
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5
LXMG1612-12-xx
TM
®
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
P RODUCTION D ATASHEET
NOTES
WWW . Microsemi .C OM
NOTES
PRODUCTION DATA – Information contained in this document is proprietary to
Microsemi and is current as of publication date. This document may not be modified in
any way without the express written consent of Microsemi. Product processing does not
necessarily include testing of all parameters. Microsemi reserves the right to change the
configuration and performance of the product and to discontinue product at any time.
Copyright © 2000
Rev. 1.1, 2007-03-27
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 6