LIGITEK LSBK3333

LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
ROUND TYPE LED LAMPS
Pb
Lead-Free Parts
LSBK3333
DATA SHEET
DOC. NO :
QW0905- LSBK3333
REV.
:
A
DATE
:
18 - Apr. - 2006
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LSBK3333
Page 1/5
Package Dimensions
5.0
5.9
7.6
8.6
1.5
MAX
25.0MIN
□0.5
TYP
1.0MIN
2.54TYP
+
-
Note : 1.All dimension are in millimeter tolerance is ± 0.25mm unless otherwise noted.
2.Specifications are subject to change without notice.
Directivity Radiation
0°
-30°
30°
-60°
100% 75% 50%
60°
25%
0
25% 50% 75% 100%
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LSBK3333
Page 2/5
Absolute Maximum Ratings at Ta=25 ℃
Ratings
Symbol
Parameter
UNIT
SBK
Forward Current
IF
30
mA
Peak Forward Current
Duty 1/10@10KHz
IFP
100
mA
Power Dissipation
PD
120
mW
Ir
50
μA
Electrostatic Discharge( * )
ESD
500
V
Operating Temperature
Topr
-20 ~ +80
℃
Storage Temperature
Tstg
-30 ~ +100
℃
Reverse Current @5V
Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic
* glove
is recommended when handing these LED. All devices, equipment and machinery must be properly
grounded.
Typical Electrical & Optical Characteristics (Ta=25 ℃)
COLOR
PART NO
MATERIAL
Emitted
LSBK3333
InGaN/SiC
Blue
Luminous
Peak Dominant Spectral Forward
wave
intensity
wave halfwidth voltage
length
@20mA(V)
@ 20mA(mcd)
length
△λ nm
λP nm λD nm
Lens
Water Clear
Viewing
angle
2θ 1/2
(deg)
Typ. Max. Min. Typ.
468
470
26
3.5
Note : 1.The forward voltage data did not including ± 0.1V testing tolerance.
2. The luminous intensity data did not including ±15% testing tolerance.
4.2
550
900
15
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Page 3/5
PART NO. LSBK3333
Typical Electro-Optical Characteristics Curve
SBK CHIP
Fig.2 Relative Intensity vs. Forward Current
30
1.5
Relative Intensity
Normalize @20mA
Forward Current(mA)
Fig.1 Forward current vs. Forward Voltage
25
20
15
10
5
0
1
2
3
4
1.25
1.0
0.75
0.5
0.25
0
5
0
5
Relative Intensity@20mA
Forward Current@20mA
40
30
20
10
0
50
75
Ambient Temperature( ℃)
20
25
30
Fig.4 Relative Intensity vs. Wavelength
Fig.3 Forward Current vs. Temperature
25
15
Forward Current(mA)
Forward Voltage(V)
0
10
100
1.0
0.5
0
380
430
480
530
580
Wavelength (nm)
630
680
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LSBK3333
Page 4/5
Soldering Condition(Pb-Free)
1.Iron:
Soldering Iron:30W Max
Temperature 350°C Max
Soldering Time:3 Seconds Max(One Time)
Distance:2mm Min(From solder joint to body)
2.Wave Soldering Profile
Dip Soldering
Preheat: 120°C Max
Preheat time: 60seconds Max
Ramp-up
2° C/sec(max)
Ramp-Down:-5° C/sec(max)
Solder Bath:260°C Max
Dipping Time:3 seconds Max
Distance:2mm Min(From solder joint to body)
Temp(° C)
260° C3sec Max
260°
5° /sec
max
120°
25°
0° 0
2° /sec
max
Preheat
60 Seconds Max
50
100
150
Time(sec)
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LSBK3333
Page 5/5
Reliability Test:
Test Item
Test Condition
Description
Reference
Standard
Operating Life Test
1.Under Room Temperature
2.If=20mA
3.t=1000 hrs (-24hrs, +72hrs)
This test is conducted for the purpose
of detemining the resistance of a part
in electrical and themal stressed.
MIL-STD-750: 1026
MIL-STD-883: 1005
JIS C 7021: B-1
High Temperature
Storage Test
1.Ta=105 ℃±5℃
2.t=1000 hrs (-24hrs, +72hrs)
The purpose of this is the resistance of
the device which is laid under condition
of high temperature for hours.
MIL-STD-883:1008
JIS C 7021: B-10
Low Temperature
Storage Test
1.Ta=-40 ℃±5 ℃
2.t=1000 hrs (-24hrs, +72hrs)
The purpose of this is the resistance
of the device which is laid under
condition of low temperature for hours.
High Temperature
High Humidity Test
1.Ta=65 ℃±5 ℃
2.RH=90 %~95%
3.t=240hrs ±2hrs
The purpose of this test is the resistance
of the device under tropical for hours.
1.Ta=105 ℃±5℃ &-40 ℃±5 ℃
(10min) (10min)
2.total 10 cycles
The purpose of this is the resistance of
the device to sudden extreme changes
in high and low temperature.
MIL-STD-202: 107D
MIL-STD-750: 1051
MIL-STD-883: 1011
Solder Resistance
Test
1.T.Sol=260 ℃±5℃
2.Dwell time= 10 ±1sec.
This test intended to determine the
thermal characteristic resistance
of the device to sudden exposures
at extreme changes in temperature
when soldering the lead wire.
MIL-STD-202: 210A
MIL-STD-750: 2031
JIS C 7021: A-1
Solderability Test
1.T.Sol=230 ℃±5℃
2.Dwell time=5 ±1sec
This test intended to see soldering well
performed or not.
MIL-STD-202: 208D
MIL-STD-750: 2026
MIL-STD-883: 2003
JIS C 7021: A-2
Thermal Shock Test
JIS C 7021: B-12
MIL-STD-202:103B
JIS C 7021: B-11