LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only ROUND TYPE LED LAMPS Pb Lead-Free Parts LSBI2640/L5 DATA SHEET DOC. NO : QW0905-LSBI2640/L5 REV. : A DATE : 18 - Oct. - 2006 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/5 PART NO. LSBI2640/L5 Package Dimensions 2.9 3.3 3.1 4.3 1.5MAX 35.0MIN □0.5 TYP 1.0MIN 2.54TYP + Note : 1.All dimension are in millimeter tolerance is ± 0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBI2640/L5 Page 2/5 Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT SBI Forward Current IF 30 mA Peak Forward Current Duty 1/10@10KHz IFP 70 mA Power Dissipation PD 120 mW Ir 50 μA Electrostatic Discharge( * ) ESD 500 V Operating Temperature Topr -20 ~ +80 ℃ Storage Temperature Tstg -30 ~ +100 ℃ Reverse Current @5V Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic * glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Typical Electrical & Optical Characteristics (Ta=25 ℃) COLOR PART NO MATERIAL Emitted LSBI2640/L5 InGaN/SiC Blue Forward Peak Dominant Spectral voltage wave wave halfwidth length length △λnm @20mA(V) λPnm λDnm @20mA(mcd) Viewing angle 2θ 1/2 (deg) Typ. Max. Min. Typ. Lens Blue Diffused Luminous intensity 430 465 65 3.8 Note : 1.The forward voltage data did not including ± 0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 4.7 12 21 50 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBI2640/L5 Page 3/5 Typical Electro-Optical Characteristics Curve SBI CHIP Fig.2 Relative Intensity vs. Wavelength 30 1.0 Relative Intensity(%) Forward Current(mA DC) Fig.1 Forward current vs. Forward Voltage 25 20 15 10 5 0 1 2 3 4 0.5 0 380 5 Forward Voltage(V) 100 Relative Intensity Relative Intensity(%) 580 630 680 10 75 50 25 0 5 10 15 20 25 30 35 40 45 Fig.5 Forward Current vs. Ambient Temperature 40 30 20 10 0 25 50 75 Ambient Temperature ( ℃) 1 0 0 25 50 75 Lead Temperature ( ℃) Forward Current (mA DC) Forward Current (mA DC) 530 Fig.4 Relative Intensity vs. Lead Temperature 125 0 480 Wavelength (nm) Fig.3 Relative Intensity vs. Forward Current 0 430 100 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSBI2640/L5 Page 4/5 Soldering Condition(Pb-Free) 1.Iron: Soldering Iron:30W Max Temperature 350° C Max Soldering Time:3 Seconds Max(One time only) Distance:2mm Min(From solder joint to body) 2.Wave Soldering Profile Dip Soldering Preheat: 120°C Max Preheat time: 60seconds Max Ramp-up 2° C/sec(max) Ramp-Down:-5° C/sec(max) Solder Bath:260°C Max Dipping Time:3 seconds Max Distance:2mm Min(From solder joint to body) Temp(° C) 260° C3sec Max 260° 5° /sec max 120° 25° 0° 0 2° /sec max Preheat 50 100 60 Seconds Max Note: 1.Wave solder should not be made more than one time. 2.You can just only select one of the soldering conditions as above. 150 Time(sec) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 5/5 PART NO. LSBI2640/L5 Reliability Test: Test Item Test Condition Description Reference Standard Operating Life Test 1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5 ℃ 2.RH=90 %~95% 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hours. 1.Ta=105 ℃±5℃ &-40 ℃±5 ℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 Thermal Shock Test JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11