AXIAL SILASTIC GUARD JUNCTION STANDARD RECTIFIER 6A05G THRU 6A10G VOLTAGE RANGE 50 to 1000 Volts CURRENT 6.0 Ampere FEATURES • • • • • R-6 Glass passivated chip junction Low reverse leakage Low forward voltage High forward surge current capability High temperature soldering guaranteed 260℃/10 seconds,0.375”(9.5mm)lead length .052(1.3) .048(1.2) 1.0(25.4) MIN. DIA. .360(9.1) .340(8.6) MECHANICAL DATA • • • • • • .360(9.1) DIA. .340(8.6) Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.07ounce, 2.0 gram 1.0(25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% 6A 6A SYMBOLS 05G 1G Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current 0.375”(9.5mm) lead length at T A=60℃ Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 6.0A TA = 25℃ Maximum DC Reverse Current at rated DC blocking Voltage at TA = 100℃ Maximum Full Load Reverse Current, full cycle Average 0.375(9.5mm) lead length at TL=105℃ Typical Junction Capacitance (NOTE 2) Typical Thermal Resistance (NOTE 1) Operating Temperature Range Storage Temperature Range 6A 2GG 200 140 200 6A 4G 400 280 400 6A 6G 600 420 600 6A 8G 800 560 800 6A 10G 1000 700 1000 UNIT Volts Volts Volts I(AV) 6.0 Amps IFSM 250 Amps VF 0.95 10.0 500 Volts IR(AV) 500 µA CJ RθJA TJ TSTG 100 10 (-55 to +150) (-55 to +150) IR Notes: 1. Thermal Resistance from Junction to Ambient with 0.375”(9.5mm) lead length, PCB. mounted with 1.1”×1.1” (30mm×30mm) copper pads. 2. Measured at 1.0 MHz and applied reverse voltage of 4.0V E-mail: [email protected] Web Site: www.cnmic.com µA pF ℃/W ℃ ℃ AXIAL SILASTIC GUARD JUNCTION STANDARD RECTIFIER 6A05G THRU 6A10G VOLTAGE RANGE 50 to 1000 Volts CURRENT 6.0 Ampere RATING AND CHRACTERISTIC CURVES 6A05S THRU 6A10S FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 400 3.0 2.0 1.0 300 8.3ms Single Half Sine-Wave (JEDEC Method) T= Tjmax 250 CURRENT, (A) 4.0 PEAK FORWARD SURGE 60 Hz Resistive or inductive Loads Ground Plane 1”×1”Copper Surface Area P.C.Board Recommended P.C. Board Mounting 5.0 (A) AVERAGE FORWARD CURRENT, 6.0 200 100 0 0 25 50 60 100 75 125 1 Cycle 175 150 1 2 4 6 8 10 40 20 60 80 100 AMBIENT TEMPERATURE, (° C) NUMBER OF CYCLES AT 60 Hz FIG.4-TYPICAL REVERSE CHARACTERISTICS FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 INSTANTANEOUS REVERSE CURRENT, (μA) 100 (A) INSTANTANEOUS FORWARD CURRENT, 1000 10 TJ =25° C Pulse Width=300us 1% Duty Cycle 1.0 10 TJ=100° C 1.0 0.1 TJ =25° C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 REVERSE VOLTAGE,(%) INSTANTANEOUS FORWARD VOLTAGE,(V) FIG.6-TYPICAL THERMAL RESISTANCE FIG.5-TYPICAL JUNCTION CAPACITANCE VS LEAD LENGTH 1000 TJ =25° C f=1MHz Vsig=50mVp-p 50 40 Single Lead to heat Sink, Insignificant Heat Flow Through Other Lead 30 R θJL 100 (° C/W) 60 THERMAL RESISTANCE, JUNCTION CAPACITANCE,(pF) 70 20 10 Both Leads to Heat Sink, Equal Length 10 0.1 1.0 10 100 0 0 REVERSE VOLTAGE,(V) E-mail: [email protected] 0.2 0.4 0.6 0.8 EQUAL LEAD LENGTH TO HEAT SINK(IN.) Web Site: www.cnmic.com 1.0