Multi Control Devices Lever and Push Operation Type Switch SLLB5 Series Compact two-way input device approximately 50% smaller than our conventional models. Typical Specifications Multi Control Devices Items Specifications Rating（max.） （min.） / （Resistive load） 10mA 5V DC/50BA 3V DC Contact resistance Operating force 1Ω max. Lever portion 0.65%0.3N Push portion 2.5%1N 0.7mm Travel（Push operation） 100,000cycles Operating life Product Line Actuator configuration Push-on switch Mounting knob integrated Location lug Minimum order unit（pcs.） Product No. With SLLB510100 Without SLLB510200 Drawing No. 1 6,000 With With SLLB520100 Without SLLB520200 2 Mounting knob Variable Resistor Type Switch Type Taping Specification (Taping Packaging) Unit:mm Reel Size Number of packages（pcs.） ¿380 1 reel 1 case／ Japan 1 case／export packing 1,500 3,000 6,000 25.4 Notes 1. Products other than those listed in the above chart are also available. Please contact us for details. 2. Please contact us for automotive use products. 3. Please place purchase orders per minimum order unit (integer). 490 Tape width （mm） 24 Multi Control Devices Lever and Push Operation Type Switch SLLB5 Series Dimensions Unit:mm Style No. PC board mounting hole and land dimensions Mounting knob integrated Travel ON CCW (0.35) (0.7) CW Multi Control Devices 0.25 8.8 1 1.8 ø1 PUSH 3.8 5. 2 Y 4. 4 2 6 0.6 2 2.2 2 1. 1.2 2.7 T 2 C 0. 1 90ﾟ PC board mounting face 1 2 0.3 9.5 X Mounting knob 1.4 ON 1.6 1 2- Travel 0.65 (0.7) (0.35) les 7 2 0.8 ho 5 0. PUSH .1 3 C CW ø1 1 0.2 0.2 CCW Y 8.5 8.15 ø1 1.3 0.5 10.2 2 1 C T 1.2 Variable Resistor Type 2 2.2 2 0.6 6 PC board mounting face 9.5 Switch Type Note Above dimensions indicate locator pin configurations only. Circuit Diagram（Push Portion） PUSH C T Code Table Code table ( 0û 20û Angle Lever circuit Terminal (15û) = ON) 20û (15û) 1 2 C CCW CW 491 Multi Control Devices List of Varieties Switch type Series Items SKQUAA/SKQUBA SKQU SKQUCA SKQUDB SSAF SRBE SLLB5 Small type SLLB Multi Control Devices Photo Function 10 7.1 10.85 10 8.6 11.8 9.5 11 11.4 8.8 3.8 3 2.2 Resin 4-direction 8-direction With Without 2-direction − With Without Without With Center-push switch Encoder Operating temperature range Rating（max.） （Resistive load） With/Without With With/ Without With Without –30℃ to ＋85℃ 50mA 12V DC With 20mA 5V DC Electrical performance Directional resolution 4-direction Insulation resistance 100MΩ min. 100V DC Voltage proof 250V AC for 1min. 1.57 ＋0.49 −0.59 N 1.57 Push operating force ＋0.39 −0.69 Without + 5V 3.14±0.59N 5KΩ Measuring terminal Measuring circuit 8-direction − 2-direction 10MΩ min. 100V DC 50MΩ min. 50V DC 100MΩ min. 100V DC 100V AC for 1min. 50V AC for 1min. N 0.5N ＋0.5 −0.35 100V AC for 1min. ＋0.7 2.5 −0.5 N 0.65±0.3N 3.5±1.5N 2±1N 2.5±1N Actuator strength Mechanical performance 3±2mN・m Terminal strength 3N for 1min. Pushing direction 50N Operating direction 50N 10N Endurance 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2 hours respectively Operating life without load Operating life with load （at rated load） Environmental Soldering performance Cold 100,000cycles –30±2℃ for 96h –40±2℃ for 96h –20±2℃for 96h Dry heat 80±2℃ for 96h 85±2℃ for 96h Damp heat 60±2℃, 90 to 95%RH for 96h 40±2℃, 90 to 95%RH for 96h Manual soldering Dip soldering Reflow soldering Page Variable Resistor Type Switch Type N Encoder detent torque Vibration With –10℃ to ＋60℃ 1mA 5V DC 10mA 5V DC 1V max. at 1mA 5V DC （Resistive load） Output voltage Directional operating force 3 12 Single-shaft Outlined specifica-tions Dimensions W （typical value） D （mm） H Number of operating shafts Shaft material Directional resolution Directional operating feeling Lever return mechanism 350℃ max. 3s max. 350±10℃ 4 +10 s 350±5℃ 3s max. 260℃ max. 5s max.（SKQUAA,CA） Please see P.492 Please see P.492（SKQUBA,DB） 482 484 486 488 490 ● Switch Type Multi Control Devices Soldering Conditions ………………………………………………………………492 ● Switch Type Multi Control Devices Cautions ………………………………………………………………………………493 471 Switch Type Multi Control Devices Soldering Conditions Example of Reflow Soldering Condition 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2φ CA（K）or CC（T）at solder joints copper foil surface）. A heat resistive tape Multi Control Devices should be used to fix thermocouple. 3. Temperature profile Temperature (˚C ) 300 A max. B 200 D E 100 Room temperature Time (s) Pre-heating F max. Series （Reflow type） A（℃） 3s max. RKJXS 260 SLLB, SLLB5 240 SKRV/SKRH/SKQUBA,DB/SSAF/SRBE 260 C B（℃） C（s） D（℃） E（℃） （s） F 40 150 Variable Resistor Type Switch Type 230 20 40 150 120 180 Notes 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the material, size thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. 492