G_S-2W & H_S-2W Series 2W,FIXED INPUT,6000V ISOLATED&UNREGULATED SINGLE/DUAL OUTPUT DC-DC CONVERTER FEATURES multi-country patent protection RoHS PRODUCT PROGRAM High Efficiency Up To 80% SIP Package 6KVDC Isolation Low isolation capacitance Temperature Range: -40°C to +85°C Continuous Short Circuit Protection No Heatsink Required No External Component Required Internal SMD Construction Industry Standard Pinout RoHS Compliance Input Part Number Efficiency (%, Typ) Current (mA) Voltage (VDC) Max Min G0505S-2W * ±5 ±200 ±20 74 G0509S-2W * ±9 ±111 ±12 77 G0512S-2W * ±12 ±83 ±9 77 G0515S-2W * ±15 ±67 ±7 77 5 400 40 74 H0509S-2W 9 222 23 77 H0512S-2W 12 167 17 77 H0515S-2W 15 133 14 77 Nominal 5 H0505S-2W APPLICATIONS Output Voltage (VDC) Range 4.5-5.5 G1205S-2W ±5 ±200 ±20 75 G1209S-2W * ±9 ±111 ±12 78 G1212S-2W * ±12 ±83 ±9 80 G1215S-2W * ±15 ±67 ±7 78 5 400 40 75 78 12 10.8-13.2 The G_S-2W & H_S-2W Series are specially H1205S-2W designed for applications where a group of H1209S-2W 9 222 23 polar power supplies are isolated from the input H1212S-2W 12 167 17 80 power supply in a distributed power supply H1215S-2W 15 133 14 78 system on a circuit board. G2405S-2W * ±5 ±200 ±20 75 These products apply to: G2409S-2W * ±9 ±111 ±12 77 G2412S-2W * ±12 ±83 ±9 80 G2415S-2W * ±15 ±67 ±7 79 5 400 40 75 H2409S-2W 9 222 23 77 H2412S-2W 12 167 17 80 H2415S-2W 15 133 14 79 1) Where the voltage of the input power supply is fixed (voltage variation ≤ ±10%); 2) Where isolation is necessary between input and output (isolation voltage ≤6000VDC); 3) Where the regulation of the output voltage and the output ripple noise are not demanding. Such as: purely digital circuits, ordinary low H2405S-2W 24 21.6-26.4 * Designing. frequency analog circuits, and IGBT power OUTPUT SPECIFICATIONS device driving circuits. Item Test Conditions Min Output power Line regulation Typ 0.2 For Vin change of ±1% Max Units 2 W ±1.2 MODEL SELECTION 10% to 100% load(5V output) 10 15 H0505S-2W 10% to 100% load(9V output) 8.3 15 10% to 100% load(12V output) 6.8 15 6.3 15 R at e d Po wer Package St yle Outpu t Voltage Input Voltag e Product Series Load regulation 10% to 100% load(15V output) Output voltage accuracy MORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Hangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 http://www.mornsun-power.com MORNSUN reserves the copyright See tolerance envelope graph Temperature drift 100% full load Ripple & Noise* 20MHz Bandwidth Switching frequency % 150 Full load nominal input (5V input) 45 Full load nominal input (12V/24V input) 50 0.03 %/°C 250 mVp-p KHz *Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. See below recommended circuits for more details. Specifications subject to change without notice. G_S-2W & H_S-2W A/2-2008 Page 1 of 2 ISOLATION SPECIFICATIONS Item Test Conditions Isolation voltage Tested for 1 minute and 1mA max Isolation resistance Test at 500VDC Units Recommended testing and application circuit If you want to further decrease the 6000 VDC input/output ripple, an “LC” filtering network may 1000 MΩ Min Typ Isolation capacitance Max 10 be connected to the input and output ends of the DC/DC converter, see (Figure 1). pF Sin gle Ou tput COMMON SPECIFICATIONS Item Test conditions Min Typ Storage humidity Max Units 95 % Operating temperature -40 85 Storage temperature -55 125 Lead temperature L L +Vo Vin 1.5mm from case for 10 seconds 15 Short circuit protection °C 0V L Cout -Vo 30 3500 Weight DC DC Cin (Figure 1) It should also be noted that the inductance and the frequency of the “LC” filtering network Plastic(UL94-V0) MTBF +Vo Cout GND Free air convection Case material L L Vin Continuous Cooling Cout 0V Du al Out p ut 300 Temp. rise at full load DC DC Cin GND K hours should be staggered with the DC/DC frequency g to avoid mutual interference. However, the 4.3 capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup TYPICAL CHARACTERISTICS problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). EXTERNAL CAPACITOR TABLE (Table 1) Ambient Temperature ( C ) OUTLINE DIMENSIONS & PIN CONNECTIONS Cin (uF) 5 12 24 - 10 4.7 2.2 - First Angle Projection regulation, (Side View) 1 2 5 7 and over-current overheat protection that is connected to the input or output end in series (Figure 2). (0.100) Dual Output Single Output Vin 1 2 DC DC GND 7 Vin GND -Vo No Pin +Vo 0V Dual Output FOOTPRINT DETAILS Single Dual PIN 1 2 5 6 +Vo REG REG 5 6 7 (Bottom View) Note: Unit:mm(inch) Pin section:0.50*0.30mm(0.020*0.012inch) Pin section tolerances: 0.10mm( 0.004inch) General tolerances: 0.25mm( 0.010inch) over-voltage protection is a linear voltage regulator with (0.020) 5 6 Dual Cout Vout (uF) (VDC) ±5 4.7 ±9 2.2 ±12 1 ±15 0.47 Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage Single Output 12 Single Cout Vout (uF) (VDC) 5 10 9 4.7 12 2.2 15 1 It’s not recommend to connect any external capacitor in the application field with less than 0.5 watt output. RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) (0.161) Vin (VDC) Vin Vin GND -Vo 0V REG GND REG +Vo REG -Vo DC DC 0V (Figure 2) +Vo Overload Protection Under normal operating conditions, the output APPLICATION NOTE circuit of these products has no protection Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should never be against overload. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load; or use our company’s No parallel connection or plug and play. products with a lower rated output power (G_S-1W & H_S-1W). MORNSUN reserves the copyright Specifications subject to change without notice. G_S-2W & H_S-2W A/2-2008 Page 2 of 2