IF_RN-1W & IF_RT-1W Series 1W,FIXED INPUT, ISOLATED & REGULATED SINGLE OUTPUT, DC-DC CONVERTER multi-country patent protection RoHS FEATURES PRODUCT PROGRAM Small Footprint, Very thin package 3KVDC Isolation Temperature Range: -40°C to +85°C No Heat sink Required High Power Density No External Component Required Industry Standard Pinout Pin-out compatible with DCP01 Series Short circuit protection RoHS Compliance Input Part Number Voltage (VDC) Nominal IF0505RN-1W 5 Range Output Current (mA) Efficiency Package (%, Typ.) Voltage (VDC) Max Min 5 200 20 70 DIP 5 200 20 70 SMD 4.75-5.25 IF0505RT-1W COMMON SPECIFICATION Item APPLICATIONS The IF_RN-1W & IF_RT-1W Series are Test Conditions Min Typ. Storage humidity Max Units 95 % specially designed for applications where a Operating temperature -40 85 group of polar power supplies are isolated from Storage temperature -55 125 the input power supply in a distributed power Temp. rise at full load supply system on a circuit board. Lead temperature These products apply to: 1) Where the voltage of the input power supply 1.5mm from case for 10 seconds Cooling 2) Where isolation is necessary between input Package material and output (isolation voltage ≤3000VDC); MTBF °C 25 260 Short circuit protection is fixed (voltage variation ≤ ±5%); 3) Where the regulation of the output voltage 15 Continuous Free air convection Epoxy Resin(UL94-V0) 3500 Weight K hours 1.4 g and the output ripple noise are not demanding. Such as: purely digital circuits, ordinary low frequency analog circuits, and IGBT power ISOLATION SPECIFICATIONS device driving circuits. Item Test Conditions Isolation voltage Tested for 1 minute and 1mA max 3000 Isolation resistance Test at 500VDC 1000 Min Isolation Capacitance Typ. Max Units VDC MΩ 25 pF MODEL SELECTION IF0505RN-1W OUTPUT SPECIFICATIONS R ated Pow er P ac ka ge St yle O ut put Voltage I np ut Voltage P roduc t Series Item Test Conditions Min Output power Typ. 0.1 Line regulation For Vin change of ±5% Load regulation 10% to 100% load MORNSUN Science& Technology co.,Ltd. Units 1 W ±0.25 ±1 % ±3 Output voltage accuracy 100% full load Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax:86-20-38601272 Http://www.mornsun-power.com Max Temperature drift Nominal input,100% full load 0.03 Ripple * 20MHz Bandwidth 10 20 Noise * 20MHz Bandwidth 50 75 Switching frequency Full load, nominal input 100 %/°C mVp-p KHz *Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. See below recommended circuits for more details. MORNSUN reserves the copyright Specifications subject to change without notice. IF_RN-1W&IF_RT-1W A/0-2008 Page 1 of 2 TYPICAL CHARACTERISTICS APPLICATION NOTE Requirement on output load To ensure this module can operate efficiently and Temperature Derating Graph reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company’s products with a lower rated output power. Operating Temp.( C ) Recommended testing circuit If you want to further decrease the input/output ripple, an RECOMMENDED REFLOW SOLDERING PROFILE “LC” filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). o 26 0 C 250 1 0 S ec Max Te m peratu r e ( o C) o 22 0 C 200 L L +Vo Vin DC DC Cin 150 GND 90 Sec Ma x ( >220 oC ) 100 Cout 0V (Figure 1) 50 It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered 0 Ti me ( s ec .) with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor OUTLINE DIMENSIONS & FOOTPRINT DETAILS must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided First Angle Pr ojection 3.25 (0.602) IF_RN-1W Series the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). IF_RT-1W Series 0.60 (0.024) 4.50 (0.177) 4.50 (0.177) S ide View EXTERNAL CAPACITOR TABLE (Table 1) Cin Vout Cout Vin (uF) (VDC) (VDC) (uF) 5 4.7 5 4.7 5.10 (0.201) 5.00 (0.197) 5 6 7 14 B ottom View 8 10.53 (0.415) 6.60 (0 .260) 7.62 ( 0.300) 6.6 0 (0.260) 1 2 It’s not recommended to connect any external capacitor in the 2.54 ( 0.010) 2.54 (0.010) 1 2 application field with less than 0.5 watt output. 5 6 7 14 19.50 (0.768) Overload Protection Under normal operating conditions, the output circuit of 8 19.50 (0. 768) 7.62 (0.300) these products has no protection against over load. The simplest method is to connect a self-recovery fuse in 7.62 (0.300) series at the input end or add a circuit breaker to the circuit. 10.53 (0.413) Input Over-voltage Protection Circuit The simplest device for input over-voltage protection is RECOMMENDED FOOTPRINT Top view,grid:2.54*2.54mm( 0.1*0.1inch) a linear voltage regulator with overheat protection that is 1.00 (0.039) 1 8 2 5 6 7 connected to the input end in series (Figure2). 2.00 (0 .0 79) 14 14 1 8 2 5 Vin 6 7 +Vout REG DC DC 1.00 (0.039) F OOTP RIN T DE TA ILS Pin 1 Function Vin 2 5 6 GND 0V +Vo NC 7,8,14 NC:No Connection Note: Unit:mm(inch) Pin section:0.50*0.25mm(0.020*0.010inch) Pin section tolerances: 0.10mm( 0.004inch) General tolerances: 0.25mm( 0.006inch) MORNSUN reserves the copyright GND 0V （Figure2） No parallel connection or plug and play. F OOT P RINT D E TAILS Pin 1 2 5 6 Function Vin GND 0V +Vo 7,8,14 NC NC:No Connection Specifications subject to change without notice. IF_RN-1W&IF_RT-1W A/0-2008 Page 2 of 2