MORNSUN IE0515KS-1W

IE_KS-1W & IE_S-1W Series
1W FIXED INPUT ISOLATED & REGULATED
DUAL OUTPUT DC-DC CONVERTER
multi-country patent protection RoHS
FEATURES
PRODUCT PROGRAM
Low ripple and good EMC features
Good dynamic feature
3KVDC Isolation
SIP Package
Temperature Range: -40°C to +85°C
Internal SMD construction
No Heat sink Required
No External Component Required
RoHS Compliance
Input
Part
Number
Voltage (VDC)
The IE_KS-1W&IE_S-1W
Series
are
specially designed for applications where a
group of polar power supplies are isolated
from the input power supply in a distributed
Current (mA)
Switching
Efficiency
frequency
(%, Typ)
(KHz,Typ.)
Voltage
(VDC)
Max
Min
IE0505S-1W
±5
±100
±10
69
83
IE0505KS-1W*
±5
±100
±10
54
83
83
Nominal
Range
±9
±56
±6
61
IE0512KS-1W
±12
±42
±5
62
83
IE0515KS-1W
±15
±33
±4
64
250
IE1205S-1W
±5
±100
±10
72
100
IE1205KS-1W*
±5
±100
±10
54
83
±9
±56
±6
61
83
IE1212KS-1W*
±12
±42
±5
63
83
IE1215KS-1W*
±15
±33
±4
64
83
IE2405S-1W
±5
±100
±10
72
83
±5
±100
±10
54
83
±9
±56
±6
60
83
IE0509KS-1W*
IE1209KS-1W*
APPLICATIONS
Output
5
12
4.75-5.25
11.4-12.6
IE2405KS-1W
24
22.8-25.2
power supply system on a circuit board.
IE2409KS-1W*
These products apply to:
IE2412KS-1W
±12
±42
±5
63
83
1) Where the voltage of the input power
IE2415KS-1W
±15
±33
±4
64
300
supply is fixed (voltage variation ≤±5%);
2) Where isolation is necessary between
input
and
output
(isolation
voltage
≤3000VDC);
3) Where the regulation of the output
* Designing.
voltage and the output ripple noise are
demanded.
ISOLATION SPECIFICATIONS
MODEL SELECTION
IE0505KS-1W
Test conditions
Min
Isolation voltage
Tested for 1 minute and 1 mA max
3000
Typ
Max
Units
VDC
Isolation resistance
Test at 500VDC
1000
MΩ
OUTPUT SPECIFICATIONS
Rated Power
Package Style
Outp ut Vo ltage
In put Volta ge
Produ ct Se ries
MORNSUN Science & Technology co.,Ltd.
Address: 2th floor 6th building, Hangzhou
Industrial District, Guangzhou, China
Tel: 86-20-38601850
Fax: 86-20-38601272
http://www.mornsun-power.com
MORNSUN reserves the copyright
Item
Item
Test conditions
Output power
Min
Typ
0.1
Max
Units
1
W
Line regulation
For Vin change of ±5%
±0.25
Load regulation
10% to 100% full load
±1
Output voltage accuracy
100% full load
±3
Temperature drift
100% full load
0.03
Output ripple*
20MHz Bandwidth
10
20
Output noise*
20MHz Bandwidth
50
100
%
%/°C
mVp-p
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at testing of Power
Converter section, application notes.
Note:
1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load
unless otherwise specified.
2. See below recommended circuits for more details.
Specifications subject to change without notice
IE_KS-1W & IE_S-1W
A/2-2008
Page 1 of 2
COMMON SPECIFICATIONS
Item
Test conditions
Min
Typ
Storage humidity
Operating temp. range
-40
Storage temp. range
Lead temperature
Units
Filtering
To get an extreme low ripple, an “LC”
95
%
filtering network may be connected to the
input
85
-55
Temp. rise at full load
Max
125
20
°C
30
1.5mm from case for 10 seconds
IEXXXXS-1W
of
1
MTBF
3500
more
mutual interference see (figure 1).
s
L
L
+Vo
Vin
Cout
DC DC
Cin
K hours
5.2
0V
L Cout
GND
Weight
DC/DC
a
significant filtering effect. It should also be
Continuous
IEXXXXKS-1W *
the
produce
staggered with the DC/DC frequency to avoid
Plastic (UL94-V0)
Short circuit protection
ends
may
of the “LC” filtering network should be
Free air convection
Case material
output
which
noted that the inductance and the frequency
300
Cooling
and
converter,
-Vo
g
(Figure 1)
*Supply voltage must be discontinued at the end of short circuit duration.
In some circuits which are sensitive to noise
and ripple, a filtering capacitor may be added
TYPICAL CHARACTERISTICS
to the DC/DC output end and input end to
reduce the noise and ripple. However, the
Temperature Derating Graph
capacitance of the output filter capacitor must
proper. If the capacitance is too big, a startup
problem might arise. For every channel of
output,
providing
operation
is
the
safe
ensured,
and
the
reliable
greatest
capacitance of its filter capacitor refer to the
external capacitor table (table1).
EXTERNAL CAPACITOR TABLE (TABLE1)
Vin
Vout
Cout
Cin
(VDC)
(VDC)
(uF)
(uF)
Operating Temp.( C )
First Angle Projection
(Bottom View)
1 2
7
9 10
2.32
9.50
0 .90
(0 .035 )
OUTLINE DIMENSIONS
2.54
RECO MMENDED FOOTPRINT
Top view,grid:2.54mm(0.1inch)
diamete r:1.00mm(0.039inch)
±5
4.7
2.2
±9
2.2
1
±12
1
--
±15
0.47
5
4.7
12
24
--
Overload Protection
Under normal operating conditions, the
1 2
7
9 10
output circuit of these products has no
protection against over-current. The simplest
(1.080)
method is to connect a self-recovery fuse in
to the circuit.
(Si de View)
4.10
12.00
(0.472)
series at the input end or add a circuit breaker
0.50
(0.020)
Note:
Unit:mm(inch)
Pin section:0.50*0.30mm(0.020*0.012inch)
Pin section toleranc es: 0.10mm( 0.004inch)
General tolera nces: 0.25 mm( 0.010inch)
FOOTPRINT DETAILS
1
Vin
2
GND
When the environment temperature is
higher than 71°C, the product output
power should be less then 60% of the
rated power.
7
+Vo
No parallel connection or plug and play.
9
-Vo
10
0V
Pin
Function
Use dual output simultaneously, forbid
opening output pin(0V) to use as single
output.
APPLICATION NOTE
Requirement on output load
To ensure this module can operate efficiently and reliably, a minimum load is specified for
this kind of DC/DC converter in addition to a maximum load (namely full load). During
operation, make sure the specified range of input voltage is not exceeded, the minimum
output load is not less than 10% of the full load, that this product should never be
operated under no load!
MORNSUN reserves the copyright
Specifications subject to change without notice
IE_KS-1W & IE_S-1W
A/2-2008
Page 2 of 2