MURATA-PS D1U4-W-1600-12-HC1C

D1U4-W-1600-12-Hx Series
AC/DC Front End Power Supply
PRODUCT OVERVIEW
The D1U4-W-1600-12-Hx is a 1600 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping
redundant systems. The main output is 12V and standby output of either 5V or 3.3V. Packaged in 1U low profile, it is
designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power architecture systems requiring high power density. The highly efficient electrical and thermal design with internal cooling
fans supports reliable operation conditions. The D1U4-W-1600-12-Hx is designed to auto-recover from over-current
and overtemperature faults. Status information is provided with front panel LEDs, logic signals and I2C management
interface. Four units can be packaged into an optional 19” 1U power shelf to provide up to 6.4kW of power..
SELECTION GUIDE
Model Number
Power Output
High Line AC
Power Output
Low Line AC
Main
Output
Standby
Output
Airflow
1600W
1600W
1600W
1600W
1200W
1200W
1200W
1200W
12V
12V
12V
12V
3.3V
5V
3.3V
5V
Back to front
Back to front
Front to back
Front to back
D1U4-W-1600-12-HC2C
D1U4-W-1600-12-HA2C
D1U4-W-1600-12-HC1C
D1U4-W-1600-12-HA1C
FEATURES
RoHS compliant
1600W (220Vac), 1200W (110Vac)
Output Power
12V Main Output,
3.3V or 5V Standby Output
1U sized; dimensions 14.0” x 4.0” x 1.6”
17.9 Watts per cubic inch density
N+1 redundancy capable,
including hot-docking
Active Current Sharing on main output
Over-voltage, Over-current,
Over-temperature protection
Internal cooling fans
I²C Bus Interface with Status Indicators
INPUT CHARACTERISTICS
Parameter
Conditions
Min.
Input Voltage Operating Range
Low Line AC
High Line AC
90
180
47
78.5
70.5
Input Frequency
Turn-on Input Voltage
Turn-off Input Voltage
Maximum Input Current
Inrush Current
Power Factor
Ramp up
Ramp down
Low Line AC 90Vac
High Line AC 180Vac
Cold start between 0-1msec
Output load >90%
Output load >50%
Typ.
55
Max.
140
264
63
86.5
78
15
10
100
Units
Vac
Hz
Vac
Arms
Apk
95%
75%
OUTPUT VOLTAGE CHARACTERISTICS
Output
Voltage
Optional 1U x 19” Power-Shelf
12V
3.3Vsb
5Vsb
Parameter
Voltage Set Point Accuracy
Line and Load Regulation
Ripple Voltage & Noise
Output Current
Load Capacitance
Voltage Set Point Accuracy
Line and Load Regulation
Ripple Voltage & Noise
Operating Range
Load Capacitance
Voltage Set Point Accuracy
Line and Load Regulation
Ripple Voltage & Noise
Operating Range
Load Capacitance
Conditions
Min.
Typ.
Max.
12.12
11.75
12.48
120
131.6
40000
20MHz Bandwidth
0
3.3
3.2
3.4
33
6
1530
20MHz Bandwidth
0
5
20MHz Bandwidth
4.85
0
5.15
50
4
1530
Units
Vdc
mV p-p
A
μF
Vdc
mV p-p
A
μF
Vdc
mV p-p
A
μF
1
Ripple and noise are measured with 0.1 uF of ceramic capacitance and 2 x 270 uF of OSCON capacitance on each
of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial
cable with 50ohm scope termination is used. See Ripple Test Setup diagram.
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U4-1600-12-Hx.A02 Page 1 of 5
D1U4-W-1600-12-Hx Series
AC/DC Front End Power Supply
OUTPUT CHARACTERISTICS
Parameter
Conditions
Remote Sense
Efficiency
Output Rise Monotonicity
120
220Vac
90.6
Overshoot less than 10% for all outputs, no voltage negative between 10% to 95% during ramp up
AC ramp up
1.5
PS_On activated
150
12V Ramp 1A/ms
±600
3.3Vsb Ramp 1A/ms
±165
5Vsb Ramp 1A/ms
±250
Start-up Time
Transient Response
Current sharing accuracy (up to 3 in parallel)
At 100% load
Hot Swap Transients
Hold-up Time
All outputs within regulation
Min.
Typ.
Max.
±10
20
Units
mV
%
s
ms
mV
%
ms
GENERAL CHARACTERISTICS
Parameter
Conditions
Storage Temperature Range
Operating Temperature Range
Operating Humidity
Storage Humidity
Shock
Sinusoidal Vibration
Non-condensing
MTBF
Acoustic
Safety Approvals
Input Fuse
Material Flammability
Switching Frequency
Weight
Non-condensing
30G non operating
0.5G, 5 – 500 Hz operating
Calculated per Bellcore at Ta=30°C
Demonstrated
ISO 7779-1999
Min.
Typ.
-40
0
10
5
Max.
70
50
90
90
200
200
60
Units
°C
%
Khrs
Khrs
dB LpAm
c-CSA-us (CSA 60950-1-03/UL 60950-1, First Edition) TUV approval (Bauart) EN 60950-1:2001
Power Supply has internal 20A/250V fast blow fuse on the AC line input
UL 94V-0
90KHz for Boost PFC Converter
165KHz for Main Output Converter
200KHz for Standby Output Converter
2.1kg
PROTECTION CHARACTERISTICS
Output
Voltage
12V
3.3Vsb
5Vsb
Parameter
Conditions
Min.
Over-temperature
Over Voltage
Over Current
Over Voltage
Over Current
Over Voltage
Over Current
Auto-restart
Latching
Latching
Latching
Latching
Latching
Latching
55
13
145
3.57
6.5
5.6
5
Typ.
Max.
Units
65
14
165
4.02
8
6
7
°C
V
A
V
A
V
A
Max.
Units
ISOLATION CHARACTERISTICS
Parameter
Insulation Safety Rating / Test Voltage
Isolation
Material Flammability
Grounding
www.murata-ps.com
Conditions
Min.
Input to Output - Reinforced
Input to Chassis - Basic
Output to Chassis
Output to Output
UL 94V-0
3000
1500
Typ.
Vrms
Vrms
Main Output Return and Standby Output Return are connected internally. 100kΩ resistor parallel with 100nF
capacitor is connected between Return and power supply chassis. Main Output Return should be connected
to the System Chassis
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U4-1600-12-Hx.A02 Page 2 of 5
D1U4-W-1600-12-Hx Series
AC/DC Front End Power Supply
CONTROL SIGNALS
Status
Conditions
LED
Off
Flashing Yellow
Flashing Green
Green
No AC input to all PS
Power Supply Failure
Main Output Absent
Power Supply Good
Status
PS-ON, PGOOD, ACOK, PS_BAD, FANFAIL, OT Warning &
shutdown, AC Range
Output Fault
12V Output
12V
Fan1 Monitor
Fan2 Monitor
12V OV, 12V UV, 12V OC, Vsb Fail, Fan1 Fail, Fan2 Fail
8 bit scaled output voltage
8 bit scaled output current
8 bit scaled output current
8 bit scaled output current
I2C Registers
Description
EMISSIONS AND IMMUNITY
Characteristic
Description
Harmonics
Voltage Fluctuation and Flicker
Emission Conducted
Emission Radiated
IEC/EN 61000-3-2
IEC/EN 61000-3-3
FCC 47 CFR Parts 15/CISPR 22/EN55022
FCC 47 CFR Parts 15/CISPR 22/EN55022
Criteria
ESD
IEC/EN 61000-4-2
Electromagnetic Field
Electrical Fast Transients/Burst
Surge
RF Conducted Immunity
Magnetic Immunity
Voltage dips, interruptions
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
IEC/EN 61000-4-8
IEC/EN 61000-4-11
Class A, 6dB margin
Class A, 6dB margin
4kV contact discharge
8kV operational air discharge
15kV non-operational air discharge
1kV/2kV, Performance Criteria B
3 Vac, 80% AM, 1kHz, Performance Criteria A
3 A/m
RIPPLE TEST SETUP
0.1uF Ceramic
2x270uF OSCON
Power Supply
Load Box
AC Phase
AC Ground
BNC to BNC Shielded Cable
General Notes:
1. Load the outputs at specified minimum
output current.
2. Connect the probe as shown with the
input tip and ground as short as possible.
Oscilloscope
20MHz BW
3. Take all measurements
4. Repeat the measurements with the
outputs at specified maximum output
current.
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U4-1600-12-Hx.A02 Page 3 of 5
D1U4-W-1600-12-Hx Series
AC/DC Front End Power Supply
OUTPUT CONNECTOR AND SIGNAL SPECIFICATION
DC and Signal Connector: Tyco Part # 1-6450132-2, or FCI PowerBlade # 51732-021
P1
VOUT
P2
VOUT
P3
VRTN
P4
VRTN
P5
P6
VRTN
VRTN
P7
VOUT
P8
x1
x2
x3
x4
x5
x6
AC_OK
P_GOOD
V_SB
RETURN
V_SB
RETURN
V_SB
+OUT
V_SB
+OUT
D
SPARE
SPARE
V_SB
RETURN
V_SB
RETURN
V_SB
+OUT
V_SB
+OUT
C
I_SHARE
I2C ADR0
I2C ADR1
I2C ADR2
PS_KILL
PS_
PRESENT
B
SENSE +
SENSE -
I2C DATA
I2 C
CLOCK
SPARE
PS_ON
A
VOUT
mate-last pins
High Level
Low Level
I Max
Main output voltage
Main output voltage, return
VOUT remote sense, positive node input, connected to the
+ve load point
VOUT remote sense, negative node input, connected to the
-ve load point
Standby voltage output
Standby voltage, return, tied internally to Output Return
Active load sharing bus
0 – 8V
-4 mA / +5 mA
>2.4V (active, OK)
<0.4V
+4 mA
-2 mA
Pin Assignment
Signal Name
Description
P1, P2, P7, P8
P3, P4, P5, P6
VOUT
VRTN
A1
Sense +
A2
Sense -
C5, C6, D5, D6
C3, C4, D3, D4
B1
V_SB
V_SB Return
I_Share
D1
AC_OK
Input AC Voltage “OK” signal output (Internal pull up is
10kΩ to Vsb)
D2
P_Good
Power good signal output (Internal pull up is 10kΩ to Vsb)
>2.4V (active, Good)
+4 mA
B5
PS_Kill
Floating pin will turn off P/S (shorter pin, last-make and
first-break contact for hot plugging). This signal overrides
PS-On in disabling the Main Output
>2.1V (open, or Vsb)
<0.7V (active, PS:On)
N/A
B6
PS_Present
Internally tied to Vsb return
0V
A6
PS_On
Internal 1K ohm pull-up to Vsb, (accepts open collector/
drain drive), This signal to be pulled low to turn-on power
supply
>2.1V (open, or Vsb)
<0.7V (active, PS:On)
A3
A4
I2C Data
I2C Clock
I2C serial data bus
I2C serial clock bus
B2
I2C Adr0
Address input 0, internal pull-up to Vsb
B3
I2C Adr1
Address input 1, internal pull-up to Vsb
B4
I2C Adr2
Address input 2, internal pull-up to Vsb
Vsb
Vsb
>2.1V, < Vsb
<0.8V
>2.1V, <Vsb
<0.8V
>2.1V, <Vsb
<0.8V
-4 mA
-1 mA
±1 mA
±1 mA
±1 mA
D1U4 MATING CONNECTORS
12V D1U4 mating connector
Solder 1
Press Fit
Straight
Murata-PS
FCI
Tyco
N/A
51742-10802400CALF
TBD
Right Angle
N/A
51762-10802400CBLF
TBD
Straight
N/A
51742-10802400AALF
TBD
Right Angle
36-0430032-0
51762-10802400ABLF
TBD
1 Solder connector recommended for board thickness of <0.090
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U4-1600-12-Hx.A02 Page 4 of 5
D1U4-W-1600-12-Hx Series
AC/DC Front End Power Supply
MECHANICAL DIMENSIONS - D1U-W-1200-12-Hx
355,60 ±0,65
[ 14.000 ±0.025 ]
8,88
[ 0.350 ]
REF
101,60 ±0,65
[ 4.000 ±0.025 ]
9,68 ±0,40
[ 0.381 ±0.015 ]
SCALE
2,40 ±0,25
[ 0.094 ±0.009 ]
0.700
12,63 ±0,40
[ 0.497 ±0.015 ]
358,48 ±0,65
[ 14.113 ±0.025 ]
41,00 ±0,40
[ 1.614 ±0.015 ]
AC Input Connector: The AC input connector is standard IEC C20 20A.
Dimensions: 14.00”L x 4.0” W x 1.6” H
OPTIONAL ACCESSORIES
Description
Part Number
12V D1U output connector card
D1U-12-CONC
APPLICAITON NOTES
Document Number
Description
ACAN-27
Output Connector Card
ACAN-29
D1U Communication Protocol
USA:
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
www.murata-ps.com email: [email protected] ISO 9001 REGISTERED
01/22/09
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2009 Murata Power Solutions, Inc.
www.murata-ps.com
Mansfield (MA), Tel: (508) 339-3000, email: [email protected]
Canada:
Toronto, Tel: (866) 740-1232, email: [email protected]
UK:
Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected]
France:
Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected]
Germany:
München, Tel: +49 (0)89-544334-0, email: [email protected]
Japan:
Tokyo, Tel: 3-3779-1031, email: [email protected]
Osaka, Tel: 6-6354-2025, email: [email protected]
China:
Shanghai, Tel: +86 215 027 3678, email: [email protected]
Guangzhou, Tel: +86 208 221 8066, email: [email protected]
Singapore:
Parkway Centre, Tel: +65 6348 9096, email: [email protected]
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U4-1600-12-Hx.A02 Page 5 of 5