6mm SMT Tactiles Series HP03 Distinctive Characteristics .244” (6.2mm) square body allows compact mounting. Heat resistant resin body meets lead-free solder processing requirements and UL flammability rating of 94V-0. Stick-tube and tape-reel packaging allow rapid automated placement of devices. Gold plated contacts available for very low voltage/current applications offer advantages of little or no oxidization or sulfurization and stable contact resistance. Gull-winged terminals ensure mechanical stability during soldering and simplified solder joint inspection. Insert molded terminals lock out flux, solvents, and other contaminants and allow automated soldering. Tape-reel packaging meets EIA-481-2 Standard. Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum distance apart of .0039” (0.10mm). (Additional coplanarity details in Terms and Acronyms in the Supplement section.) Actual Size NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 6mm SMT Tactiles Series HP03 General Specifications Electrical Capacity (Resistive Load) Power Level (code P2): Logic Level (code P4): 3VA maximum @ 28V DC maximum (Applicable Range 10mA ~ 125mA @ 0.1V ~ 28V) 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: See Supplement for further explanation of operating range. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Total Travel: Materials & Finishes Actuator: Case: Base: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Processing Soldering: Cleaning: Standards & Certifications Flammability Standards: UL Recognition & CSA Certification: 100 milliohms maximum 100 megohms minimum @ 100V DC 250V AC minimum for 1 minute minimum between contacts & between contacts & case 500,000 operations minimum 500,000 operations minimum 1.60N .008” (0.2mm) Glass fiber reinforced polyamide (UL94V-0) Stainless steel Glass fiber reinforced polyamide (UL94V-0) Stainless steel with silver or gold plating Brass with silver or gold plating Brass with silver or gold plating –20°C through +70°C (–4°F through +158°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 100G (981m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Reflow Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 actuator and base These switches are designed for use in a low-voltage, low-current circuit. When used as intended, the results do not produce hazardous energy. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 6mm SMT Tactiles Series HP03 TYPICAL SWITCH ORDERING EXAMPLE 15A HP03 F POLE & CIRCUIT 15A SPST OFF P4 K R PACKAGING ACTUATOR COLOR K (ON) Black ( ) = Momentary Normally Open Contacts TERMINALS & CONTACTS ACTUATOR F Flat Button P2 Gull Wing for Upright Mount; Silver Contacts Rated 3VA max. DC P4 Gull Wing for Upright Mount; Gold Contacts Rated 0.4VA max. @ 28V AC/DC max. S Stick-Tube 100 Pieces/ Tube R Tape-Reel 1,000 Pieces/ Reel DESCRIPTION FOR TYPICAL ORDERING EXAMPLE HP0315AFKP4-R Gold Contacts with 0.4VA Rating Flat Black Button SPST OFF-(ON) Circuit and Normally Open Contacts Gull Wing Terminals for Upright Mount Tape-Reel Packaging POLE & CIRCUIT Actuator Position ( ) = Momentary Normal Pole Down Model HP0315A SP Switch Throw & Schematic SPST OFF 1 3 2 4 (ON) Note: Terminal numbers are not actually on the switch. TYPICAL SWITCH DIMENSIONS Gull-winged (3.5) Dia .138 (0.3) Typ .012 (0.5) Max .020 (2.2) Typ .087 1 (6.2) .244 1 (9.0) .354 2 HP0315AFKP4 3 3 (9.0) .354 (6.2) .244 (0.8) .031 (4.4) .173 4 (0.5) .020 (4.5) .177 4 (0.7) Typ .028 2 (4.5) .177 (1.4) Typ .055 NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series HP03 6mm SMT Tactiles PACKAGING S R Stick-Tube Switches must be ordered in 100piece increments when stick-tube packaging is selected. Tape-Reel Switches must be ordered in 1,000-piece increments when tape-reel packaging is selected. Packaging meets EIA-481-2 Standard. Stick-Tube Dimensions (10.5) .413 Each stick-tube contains 100 switches (12.5) .492 (660.0) 25.984 Tape-Reel Dimensions Each tape-reel of 1,100 pockets contains 1,000 switches. Minimum Leader Length: 15.748” (400mm). Minimum Trailer Length: 6.299” (160mm). (2.0) Typ .079 (6.5) R .256 (12.0) Typ .472 (4.0) Typ .157 (1.5) Dia Typ .059 (4.6) .181 (5.1) .201 (1.75) .069 (80.0) Dia 3.150 (10.5) Typ .413 (2.0) Typ .079 Overall Dia (330.0) 13.0 (16.4) .646 (7.5) (16.0) .295 .630 3° Max (6.5) .256 (0.4) .016 Direction of Feed (22.4) Max .882 (3.0) .118 KEYBOARD MATRIX Common Bus Matrix 6 10 6 4 7 8 9 3 11 8 A B 0 1 2 12 1 2 3 4 5 6 7 8 9 0 A B P C Te r m i n a t i o n s 1 2 3 4 5 6 7 8 9 10 11 12 13 3 2 1 1 5 4 6 2 7 8 9 6 A B 0 7 = ON 7 5 4 Keys (Switches) 5 4 13 Keys (Switches) 3 2 1 X-Y Matrix 9 5 P C Te rmina ti ons 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 0 A B = ON 3 Blue = PCB Trace, Black = Switch Circuit Blue = PCB Trace, Black = Switch Circuit These single pole, single throw switches can be used in a keyboard matrix and, using strapped terminals, achieve a common bus electrical configuration on a single-sided PC board. These single pole, single throw switches can be arranged on a single-sided PC board matrix with strapped terminals to achieve an X-Y type electrical interconnection. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07