6mm Tactiles Series HP02 Distinctive Characteristics .244” (6.2mm) square body allows compact mounting. Heat resistant resin body meets lead-free solder processing requirements and UL flammability rating of 94V-0. Stick-tube packaging allows rapid automated placement of devices. Gold plated contacts available for very low voltage/current applications offer advantages of little or no oxidization or sulfurization and stable contact resistance. Crimped terminals provide a spring type action which ensures secure mounting and prevents dislodging during automated soldering. Insert molded terminals lock out flux, solvents, and other contaminants and allow automated soldering. Actual Size NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 6mm Tactiles Series HP02 General Specifications Electrical Capacity (Resistive Load) Power Level (code P2): Logic Level (code P4): 3VA maximum @ 28V DC maximum (Applicable Range 10mA ~ 125mA @ 0.1V ~ 28V) 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: See Supplement for further explanation of operating range. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Total Travel: Materials & Finishes Actuator: Case: Base: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: PCB Processing Soldering: Cleaning: Standards & Certifications Flammability Standards: UL Recognition & CSA Certification: 100 milliohms maximum 100 megohms minimum @ 100V DC 250V AC minimum for 1 minute minimum between contacts & between contacts & case 500,000 operations minimum 500,000 operations minimum 1.60N .008” (0.2mm) Glass fiber reinforced polyamide (UL94V-0) Stainless steel Glass fiber reinforced polyamide (UL94V-0) Stainless steel with silver or gold plating Brass with silver or gold plating Brass with silver or gold plating –20°C through +70°C (–4°F through +158°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 100G (981m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 actuator and base These switches are designed for use in a low-voltage, low-current circuit. When used as intended, the results do not produce hazardous energy. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series HP02 6mm Tactiles TYPICAL SWITCH ORDERING EXAMPLE 15A HP02 F POLE & CIRCUIT 15A SPST OFF P2 K S ACTUATOR COLOR K (ON) Black ( ) = Momentary Normally Open Contacts PACKAGING TERMINALS & CONTACTS ACTUATOR F Flat Button P2 Straight PC; Silver Contacts Rated 3VA max. DC P4 Straight PC; Gold Contacts Rated 0.4VA max. @ 28V AC/DC max. Stick-Tube 100 Pieces/ Tube S DESCRIPTION FOR TYPICAL ORDERING EXAMPLE HP0215AFKP2-S Silver Contacts with 3VA Rating Flat Black Button SPST OFF-(ON) Circuit and Normally Open Contacts Straight PC Terminals Stick-Tube Packaging POLE & CIRCUIT Actuator Position ( ) = Momentary Normal Pole Down Model HP0215A SP Switch Throw & Schematic SPST OFF 1 3 2 4 (ON) Note: Terminal numbers are not actually on the switch. TYPICAL SWITCH DIMENSIONS Straight PC (3.5) Dia .138 (3.5) .138 (0.5) Max .020 1 3 (6.7) .264 (6.2) .244 2 (6.2) .244 (4.3) .169 1 4 2 (6.7) .264 4 (0.3) Typ .012 (0.8) .031 3 (0.7) Typ .028 (4.5) .177 (1.0) Dia Typ .039 (4.5) .177 HP0215AFKP2 NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series HP02 6mm Tactiles PACKAGING S Stick-Tube Switches must be ordered in 100-piece increments. Stick-Tube Dimensions (10.5) .413 Each stick-tube contains 100 switches. (12.5) .492 (660.0) 25.984 KEYBOARD MATRIX X-Y Matrix Common Bus Matrix 9 1 5 4 6 13 10 6 4 7 8 9 3 11 8 A B 0 1 2 12 1 2 3 4 5 6 7 8 9 0 A B P C Te r m i n a t i o n s 1 2 3 4 5 6 7 8 9 10 11 12 13 3 2 1 1 5 4 6 2 7 8 9 6 A B 0 7 = ON 7 Blue = PCB Trace, Black = Switch Circuit These single pole, single throw switches can be used in a keyboard matrix and, using strapped terminals, achieve a common bus electrical configuration on a single-sided PC board. 5 4 Keys (Switches) 3 2 Keys (Switches) 5 P C Termi nat ions 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 0 A B = ON 3 Blue = PCB Trace, Black = Switch Circuit These single pole, single throw switches can be arranged on a single-sided PC board matrix with strapped terminals to achieve an X-Y type electrical interconnection. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07