PCA EPA2116G

10Base-T Interface Module with
Enhanced CMA and Resistor Network
ELECTRONICS INC.
EPA2116G
• Optimized for AMD/PHY controllers •
• Robust construction allows for IR/VP processes •
• Complies with or exceeds IEEE 802.3, 10Base-T Requirements •
Electrical Parameters @ 25° C
Cut-off
Frequency
(MHz)
Insertion
Loss
(dB Max.)
Return
Loss
(dB Min.)
± 1.0
MHz
1-10
MHz
5-10
MHz
Attenuation
(dB Min.) (1)
@ 20
MHz
@ 25
MHz
@ 30
MHz
Common Mode Rejection
(dB Min.)
Crosstalk
(dB Min.)
[Between Channels]
@ 1-100
MHz
@ 1-10
MHz
@ 40
MHz
Xmit
Rcv
Xmit
Rcv
Xmit
Rcv
Xmit
Rcv
Xmit
Rcv
Xmit
Rcv
Xmit
Rcv
Xmit
Rcv
17
17
-1.5
-1
-15
-15
-7
-5
-18
-11
-30
-16
-33
-26
-30
-30
•
1
Isolation : meets or exceeds 802.3 IEEE Requirements • Characteristic Filter Impedance : 100 Ω •
• Note: 1) Referenced to the filter output @ 5 MHz for filter only, excluding resistor network. •
Schematic
Transmit Channel
61.9Ω
8
LPF
1.2KΩ
Receive Channel
14
422Ω
2
49.9Ω
11
LPF
15
3
1:1
61.9Ω
4
6
49.9Ω
7
16
422Ω
5
Chip Side
10
12
Chip Side
Media Side
Media Side
Dimensions
A
Dim.
Min.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
Q
.880
.360
.430
.700
.010
.100
.490
.017
.008
.095
0°
.025
N
J
PCA
EPA2116G
Date Code
B
Pad
Layout
Q
D
E
K
L
H
PCA ELECTRONICS, INC.
16799 SCHOENBORN ST.
NORTH HILLS, CA 91343
P
M
C
F
9
1:1
Package
Pin 1
I.D.
-35
(Inches)
Max. Nom.
.900
.380
.450
Typ.
.015
Typ.
.510
.022
.012
Typ.
5°
.045
(Millimeters)
Min. Max. Nom.
22.35
9.14
10.92
17.78
.254
2.54
12.45
.432
.203
2.41
0°
.635
.040
.100
.100
.540
22.86
9.65
11.43
Typ.
.381
Typ.
12.95
.559
.305
Typ.
5°
1.14
1.02
2.54
2.54
13.72
I
G
CSA2116Ga Rev. A
2/18/98
Product performance is limited to specified parameters. Data is subject to change without prior notice.
TEL: (818) 892-0761
FAX: (818) 894-5791
http://www.pca.com
10Base-T Module with
Enhanced Common Mode Attenuation
ELECTRONICS INC.
EPA2116G
The circuit below is a guideline for interconnecting PCA’s EPA2116G with AMD 79C96X and -970, PCnet chip family as
reference controllers. Further details of system design, such as chip pin-out, etc. can be obtained from the specific chip
manufacturer.
Typical insertion loss of the isolation transformer/filter is 0.7dB. This parameter covers the entire spectrum of the encoded
signals in 10 Base-T protocols. However, the predistortion resistor network introduces some loss which has to be taken
into account in determining how well your design meets the Standard Template requirements.
Users are encouraged to verify if this network best suits their application needs with the chip manufacturer before choosing
a specific set of values. Additionally, user should make sure that these resistor values provide 802.3 Return Loss
specification complaince at either extremes of the cable impedance, namely; 85Ω to 115Ω. Implement only those parts in
the design that will meet this requirement.
A quick calculation of the effective Thevenin’s termination impedance for the filter follows:
R(termination)= 2(61.9//422)//1.2K≈100Ω.
Thus, when measuring the return loss of these parts on the bench, it is not necessary to provide a shunting resistor across
the four outputs.
The phantom resistors shown around the RJ45 connector have been known to suppress unwanted radiation that unused
wires pick up from the immediate environment. Their placement and use are to be considered carefully before a design is
finalized.
It is recommended that there be a neat separation of ground planes in the layout. It is generally accepted practice to limit
the plane off at least 0.08 inches away from the chip side pins of EPA2116G. There need not be any ground plane beyond
this point.
For best results, PCB designer should design the outgoing traces preferably to be 50Ω, balanced and well coupled to
achieve minimum radiation from these traces.
Typical Application Circuit for UTP
TX+
TXd+
10 Base-T
PHY
TXTXdRX+
RX-
1
8
1
2
6
2
3
11
3
4
9
6
TX+
TX-
RJ45*
RX+
RX4
5
7
8
14
16
EPA2116G
5
12
Chassis
Ground
Notes : * Pin-outs shown are for NIC configurations.
For Hubs and Repeaters swap pins 1-2 with pins 3-6.
PCA ELECTRONICS, INC.
16799 SCHOENBORN ST.
NORTH HILLS, CA 91343
CSA2116Gb
Rev. A
2/18/98
TEL: (818) 892-0761
FAX: (818) 894-5791
http://www.pca.com