COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Description Features Pericom Semiconductor’s PI3HDMI series of switch circuits are targeted for high-resolution video networks that are based on DVI/ HDMI standards, and TMDS signal processing. The PI3HDMI412-A is a 8- to 4-Channel Mux/DeMux Switch. The device multiplexes differential signals to one of two corresponding outputs. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. It is designed for low bit-to-bit skew and high channel-to-channel noise isolation. 4-Differential Channel 2:1 Mux/DeMux TMDS Signaling Data Rate: 1.65Gbps Crosstalk: -25dB@825MHz Switching speed: 4ns Isolation: -30dB@825MHz ESD: Data bits @ 8kV HBM, select bit @ 2 kV HBM Near-Zero Prop Delay: 250ps max. Low bit-to-bit skew Hot insertion capable Enable/Disable Time: 9ns Bidirectional Packaging (Pb-free & Green): - 42-pin TQFN (ZH) - 48-pin BQSOP (B) � �� � �� � �� � �� Because of its passive bidirectional feature, this switch can be used either at the video drivers side or at the receiver side. For PC graphics applications, the device sits at the drivers side to switch between multiple display units such as PC LCD monitor, projector, TV, etc. For consumer video applications, the device sits at the receiver end to switch between the source components such as DVD, D-VHS, STB, etc. Pin Descriptions (Top View) Block Diagram ��� ��� ��� ��� The maximum DVI/HDMI data rate of 1.65Gbps provides the resolution required by the next generation HDTV and PC graphics. Three differential channels are used for data (video signals for DVI or audio/video signals for HDMI), and one differential channel is used for Clock for decoding the TMDS signals at the outputs. ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ���� ��� ��� ��� ��� • • • • • • • • • • • • • � � � � � � � � � �� �� �� �� �� �� �� �� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� �� �� �� �� ��� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��� ��� ��� ��� ��� 42-pin TQFN 1 ���� ���� ���� ���� ���� ���� ���� ���� ��� ���� ���� ���� ���� ���� ���� ���� ���� VSS VDD VSS VSS C0+ C0- VSS VDD C1+ C1VSS VDD SEL VSS C2+ C2VDD VSS C3+ C3VSS VSS VDD VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 VDD VSS C0+A C0-A C1+A C1-A VSS C0+B C0-B C1+B C1-B VSS VDD C2+A C2-A C3+A C3-A VSS C2+B C2-B C3+B C3-B VSS VDD 48-pin BQSOP PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Truth Table Pin Description Function SEL NA L N to NB H N to Pin # Pin Name 5, 8, 13, 18, 20, 30, 40, 42 VDD + Power supply 3.30 1, 4, 10, 14, 17, 19, 21, 39, 41 VSS - Power supply 9 SEL Select pin, see truth table 2, 3, 6, 7, 11, 12, 15, 16, 31-38, 22-29 CXtx Data + Clk bits for TMDS signal Description Maximum Ratings (Above which useful life may be impaired. For user guidelines, not tested.) Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Storage Temperature....................................–65°C to +150°C Supply Voltage to VSS Potential...............–0.5V to +2.5V DC Input Voltage ...............................................VSS to VDD DC Output Current......................................................120mA Power Dissipation...........................................................0.5W DC Power Supply Characteristics Paramenter Description Min. Max. Units VDD Positive Power Supply 3.0 3.6 V VSS Negative Power Supply 1.5 1.6 V DC Electrical Characteristics for Switching over Operating Range (TA = –40°C to +85°C) Paramenter Typ(2) Description Test Conditions Min. VIH(3) Input HIGH Voltage Guaranteed HIGH level 0.65(VDD-VSS)+VSS VIL(3) Input LOW Voltage Guaranteed LOW level –0.5+VSS VIK Clamp Diode Voltage VDD=Max., IIN=–18mA IIH Input HIGH Current VDD=Max., VIN=VDD ±5 IIL Input LOW Current VDD=Max., VIN=VSS ±5 –0.7+VSS Max. Units 0.35(VDD-VSS)+VSS V –1.2+VSS µA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at TA = 25°C ambient and maximum loading. 3. VIH + VIL are for SEL input only. 2 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Power Supply Characteristics Parameters ICC Test Conditions(1) Description Quiescent Power Supply Current Min. VDD = Max., VIN = VDD or VSS Typ.(2) Max. 200 Units µA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at TA = 25°C ambient and maximum loading. Dynamic Electrical Characteristics Over the Operating Range (TA= -40º to +85ºC) Parameter Description Test Conditions Min. Typ.(2) Crosstalk See Fig. 1 for Measurement Setup, f = 825 MHz -25 OIRR OFF Isolation See Fig. 2 for Measurement Setup, f = 825 MHz -30 DR Data Rate XTALK Max. Units dB 4.0 Gbps ������� � � � �������� ������������ ������ ��� ����� ������ ������ ��� ���� Fig 1. Crosstalk Setup 3 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard ������� � � � �������� ������ ������������ ������ ������ ��� ���� Fig 2. Off-isolation setup Fig 3. Crosstalk 4 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Fig 4. Off Isolation Switching Characteristics (TA= -40º to +85ºC, VSS=0V, VDD=1.8V ±10%) Paramenter tPZH, tPZL tPHZ, tPLZ Description Min. Typ.(2) Max. Line Enable Time - SEL to AN, BN 0.5 8.0 Line Disable Time - SEL to AN, BN 0.5 4.0 Units ns Notes: 1. For measurement setup, please see “Test Circuit For Electrical Characteristic” on page 6, and “Switching waveforms” on page 7 5 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Test Circuit for Electrical Characteristics(1) ������� ��� ������� ��� ������ ��������� ���� ����� ��� �� �� ������� Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator 3. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. 4. All input impulses are supplied by generators having the following characteristics: PRR ≤ MHz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns. 5. The outputs are measured one at a time with one transition per measurement. Switch Positions Test Switch tPLZ, tPZL (output on B-side) 2 x (VDD - VSS) tPHZ, tPZH (output on B-side) VSS Prop Delay Open Test Circuit for Dynamic Electrical Characteristics �� ��������������������� �� �� ������������ �������� 6 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Switching Waveforms ��� ��� ����� ����� ��� ������ ���� ���� ���� ������ ����������� ���� ���� ����������� ������ ��� ��� ���� ������ Voltage Waveforms Enable and Disable Times 3.3V PI3HDMI412-A 3.3V 1.8k-ohm Select Line 1.5V 1.5k-ohm Select Line Example of a circuit that needs to be connected to the select lines of our device: 7 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Application Test Results Figure 1. TMDS TP2 Tx eye compliance test setup Figure 2. TMDS TP3 Rx "switch at receiver" eye compliance test setup 8 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Figure 3. TP2 (Tx) eye-measurements (left is with switch, right is without switch), refer to figure 1 for the test set up Figure 4. TP3 (Rx) - “Switch at receiver side” with 2-meter cable eye-measurements (left is with switch, right is without switch), refer to figure 2 for the test set up. 9 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Packaging Mechanical: 42-pin TQFN (ZH) Pin #1 Corner 2.05±.05 0.80±0.04 7.55±.05 3.50±0.10 0.5 9.0±0.10 Pin #1 Corner 0.20 REF. 0.4±0.05 0.25±.05 0.6±.03 Packaging Mechanical: 48-pin BQSOP (B) 48 .150 .157 3.80 4.00 .228 .244 5.80 6.20 Gauge Plane .020 .029 0.50 0.75 .010 0.25 BSC 1 .014 0.356 REF .386 .394 9.80 10.00 .015 0.381 x 45˚ .008 0.20 Nom Nom .063 1.60 .0157 BSC 0.40 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS 5˚ .0051 .009 0.13 0.23 10 .079 2.0 Max .002 0.05 .009 0.25 PS8814 02/08/06 COMPANY CONFIDENTIAL PI3HDMI412-A 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Ordering Information Ordering Code PI3HDMI412-AZHE PI3HDMI412-ABE Package Code Package Description ZH Pb-free & Green, 42-pin TQFN B Pb-free & Green, 42-pin BQSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 11 PS8814 02/08/06