LABORATORY SM 6000 Series 6 0 0 0 W A T T S P R O G R A M M A B L E D C S U P P LY Features • • • • • • • Constant voltage and constant current operation Parallel operation master/slave EMC standard EN61204-3 CE marked Optional ethernet, RS232, IEEE 488 programming IEEE 488 programming option Ethernet, RS232 option Specifications OPERATING INPUT Efficiency 87%–91% Switching frequency 100kHz Thermal protection Yes 20A (electronic limit) Programming I/P to O/P: 3750V rms (8mm creepage), I/P – Case: 2500V rms, O/P – Case: 600VDC Analogue Programming of voltage and current by 0-5V. Programming speed See table Master/Slave operation Parallel and series operation with equal current and voltage sharing. In this way two or more SMunits can together be used as one high power unit. Voltage and current of the units is controlled by the master (by potentiometers or by programming). Series operation up to 600V Input voltage 342-457Vac 3 phase Frequency 48Hz–62Hz Inrush current Isolation OUTPUT Output voltage See table. Output voltage adjustment 0%–100% Output current See table. Output current adjustment 0%–100% Metering Digital meters standard Resolution 0.03% voltage and current control with 10 turn potentiometers. Indicators CV/CC mode, OVP triggered LEDs Temperature coefficient CV: 35x10-6 /°C, CC: 60x10-6 /°C Load regulation 0%–100% load see table Line regulation Line ±10% – see table The CV/CC regulated power supplies are very suitable for battery charging. Ask for the special datasheet “BATTERY CHARGING WITH SM-series POWER SUPPLIES”. This datasheet contains information about protective measures against accidental battery reversing. Ripple & Noise See table. ENVIRONMENTAL Operating temperature -20°C to 50°C SM15-400: < 0.5mΩ; < 2.3mΩ SM30-200: < 1.2mΩ; < 5mΩ SM45-140: < 1.7mΩ; < 10mΩ SM60-100: < 1.5mΩ; < 12mΩ SM70-90: < 1.8mΩ; < 12mΩ SM120-50: < 11mΩ; < 90mΩ SM300-20: < 34mΩ; < 330mΩ Cooling Low noise blower, fan speed adapts to temperature of internal heatsink. (from left to right). (50%–100% load step): 100µS; 120µS for SM 15-400. Stability CV: 5x10 , CC: 10x10 Output impedance (0-1kHz; 1-100kHz) Recovery time Remote sense BATTERY CHARGING -5 -5 2V max. per lead compensation. STANDARDS AND APPROVALS Safety standards EN60950 / EN61010 EMC standards EN61204-3, EN61000-6-2 EMI standards EN61000-6-3 (EN55022B) MECHANICAL Mounting 470 Bench or 19" rack mounting LABORATORY SM 6000 Series 6 0 0 0 W A T T S P R O G R A M M A B L E D C S U P P LY Selection Table OUTPUT VOLTAGE (0V TO) OUTPUT CURRENT (0A TO) SM15-400 15V 400A 8mV pk-pk 300mA pk-pk 3.3mS 2.5mV 24mA 0.2mV 4mA SM30-200 30V 200A 8mV pk-pk 60mA pk-pk 6.4mS 5mV 12mA 0.5mV 2mA SM45-140 45V 140A 10mV pk-pk 25mA pk-pk 2.7mS 5mV 9mA 1mV 1.5mA SM60-100 60V 100A 10mV pk-pk 10mA pk-pk 5.4mS 5mV 6mA 2mV 1mA SM70-90 70V 90A 10mV pk-pk 10mA pk-pk 6.8mS 5mV 5mA 2mV 1mA SM120-50 120V 50A 25mV pk-pk 10mA pk-pk 5.1mS 8mV 3mA 2mV 0.5mA SM300-20 300V 20A 50mV pk-pk 5mA pk-pk 8.5mS 15mV 1.2mA 3mV 0.2mA MODEL NUMBER RIPPLE & NOISE CV CC PROGRAMMING SPEED LOAD REG. 0%–100% CV CC LINE REG. 200–264VAC CV CC OPTIONS Screwdriver adjustment - option P001 Master / slave operation Battery charging SM45-140: P151, SM120-50: P152, SM300-20: P153 Increased max. output voltage / current - option P069 Enforced secondary isolation 1000V - option P089 High speed programming - SM15-400: P166, SM30-200: P167, SM45-140: P168, SM60-100: P169, SM70-90: P170, SM120-50: P171, SM300-20: P172. Built-in ISO AMP CARD for isolated analog programming - option P154 Built-in ethernet power supply controller - option P157 Built-in RS232 power suply controller - option P155 Built-in IEEE488 power supply controller - option P156 440 and 480 Vac input - option P165 Technical Illustrations Your dependable power partner – www.powerbox.com.au 471