05066 PSOT03LC thru PSOT36LC Only One Name Means ProTek’Tion™ ULTRA LOW CAPACITANCE TVS ARRAY APPLICATIONS ✔ Ethernet - 10/100 Base T ✔ Cellular Phones ✔ FireWire ✔ Audio/Video Inputs ✔ Portable Electronics IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Ground) & Level 2(Line-Line) SOT-23 FEATURES ✔ ESD Protection > 40 kilovolts ✔ 500 Watts Peak Pulse Power per Line (tp = 8/20µs) ✔ Low Clamping Voltage ✔ Available in Multiple Voltage Types Ranging from 3V to 36V ✔ ULTRA LOW CAPACITANCE: 5pF MECHANICAL CHARACTERISTICS ✔ Molded JEDEC SOT-23 ✔ Weight 14 milligrams (Approximate) ✔ Flammability rating UL 94V-0 ✔ 8mm Tape and Reel Per EIA Standard 481 ✔ Device Marking: Marking Code PIN CONFIGURATION 1 3 2 05066.R4 8/03 1 www.protekdevices.com PSOT03LC thru PSOT36LC DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified SYMBOL VALUE UNITS Peak Pulse Power - tp= 8/20µs (See Figure 1) PPP 500 W Operating Temperature TJ -55°C to 150°C °C TSTG -55°C to 150°C °C PARAMETER Storage Temperature ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER (Note 1) DEVICE MARKING 03L 05L 08L 12L 15L 24L 36L PSOT03LC PSOT05LC PSOT08LC PSOT12LC PSOT15LC PSOT24LC PSOT36LC RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE (See Note 2) MAXIMUM CLAMPING VOLTAGE (See Fig. 2) MAXIMUM CLAMPING VOLTAGE (See Fig. 2) V WM VOLTS @ 1mA V(BR) VOLTS @ IP = 1A VC VOLTS 3.3 5.0 8.0 12.0 15.0 24.0 36.0 4.0 6.0 8.5 13.3 16.7 26.7 40.0 7.0 9.8 13.4 19.0 24.0 43.0 51.0 MAXIMUM LEAKAGE CURRENT TYPICAL CAPACITANCE @8/20µs VC @ IPP @VWM ID µA @0V, 1 MHz C pF 10.9V @ 43.0A 13.5V @ 42.0A 16.9V @ 34.0A 25.9V @ 21.0A 30.0V @ 17.0A 49.0V @ 12.0A 76.8V @ 9.0A 125 20 10 1 1 1 1 5 5 5 5 5 5 5 Note 1: Positive potential is applied from pin 1 to 2; pin 2 is ground. Note 2: Do not test or surge from pin 2 to 1. PIV typically greater than 100V for the rectifier diode. FIGURE 1 PEAK PULSE POWER VS PULSE TIME 120 IPP - Peak Pulse Current - % of IPP PPP - Peak Pulse Current - Watts 10,000 500W, 8/20µs Waveform 1,000 100 10 0.01 05066.R4 8/03 FIGURE 2 PULSE WAVE FORM tf 100 TEST WAVEFORM PARAMETERS tf = 8µs td = 20µs Peak Value IPP 80 e-t 60 40 td = t I /2 PP 20 0 1 10 100 td - Pulse Duration - µs 1,000 10,000 2 0 5 10 15 t - Time - µs 20 25 30 www.protekdevices.com PSOT03LC thru PSOT36LC GRAPHS FIGURE 3 POWER DERATING CURVE 100 Peak Pulse Power 8/20µs % Of Rated Power 80 60 40 20 Average Power 0 0 25 50 75 100 125 TL - Lead Temperature - °C 150 FIGURE 4 OVERSHOOT & CLAMPING VOLTAGE FOR PSOT03LC 5 Volts per Division 40 30 20 10 0 ESD Test Pulse: 7 kilovolt, 1/30ns (waveform) FIGURE 5 TYPICAL CLAMPING VOLTAGE VS PEAK PULSE CURRENT FOR PSOT05LC VC - Clamping Voltage - Volts 16 12 8 4 0 0 05066.R4 8/03 2 4 6 8 10 12 IPP - Peak Pulse Current - Amps 3 14 16 18 www.protekdevices.com PSOT03LC thru PSOT36LC APPLICATION NOTE The PSOTxxLC Series are low capacitance TVS arrays designed to protect I/O or data lines from the damaging effects of ESD or EFT. This product series provides unidirectional & bidirectional protection, with a surge capability of 500 Watts PPP per line for an 8/20µs waveform and ESD protection > 40 kilovolts. BIDIRECTIONAL COMMON-MODE CONFIGRUATION (Figure 1) Figure 1 - Common-Mode I/O Port Protection Two PSOTxxLC devices, when used in paralell, provide protection in a common-mode configuration as depicted in Figure 1. I/O LINE Circuit connectivity is as follows: ✔ ✔ ✔ ✔ ✔ I/O Line is connected to Device 1, Pin 1. I/O Line is connect to Device 2, Pin 2. Device 1, Pin 2 is connected to ground. Device 2, Pin 1 is connected to ground. Device 1 & 2, Pin 3 is not connected. 1 2 3 3 2 1 BIDIRECTIONAL DIFFERENTIAL-MODE CONFIGRUATION (Figure 1) In addition, two PSOTxxLC devices, when used in paralell, provide protection in a differential-mode configuration for Ethernet applications as depicted in Figure 2. GND Circuit connectivity is as follows: ✔ ✔ ✔ ✔ ✔ I/O Line 1 is connected to Device 1, Pin 1. I/O Line 1 is connect to Device 2, Pin 2. I/O Line 2 is connected to Device 1, Pin 1. I/O Line 2 is connect to Device 2, Pin 2. Device 1 & 2, Pin 3 is not connected. Figure 2 - Differential-Mode Ethernet Protection Circuit board layout is critical for Electromagnetic Compatibility (EMC) protection. The following guidelines are recommended: ✔ The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. ✔ The path length between the TVS device and the protected line should be minimized. ✔ All conductive loops including power and ground loops should be minimized. ✔ The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. ✔ Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 05066.R4 8/03 ETHERNET TRANSCEIVER I/O 1 CIRCUIT BOARD LAYOUT RECOMMENDATIONS 1 2 3 2 3 1 I/O 2 4 www.protekdevices.com PSOT03LC thru PSOT36LC PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE SOT-23 A L 0º - 10º 3 B 1 S PACKAGE DIMENSIONS 2 K J DIM V A B C D G H J K L S V G C D H MILLIMETERS MIN MAX 2.80 1.20 0.89 0.37 1.78 0.013 0.085 0.45 0.89 2.10 0.45 3.04 1.40 1.11 0.50 2.04 0.100 0.177 0.60 1.02 2.50 0.60 INCHES MIN MAX 0.1102 0.0472 0.0350 0.0150 0.0701 0.0005 0.0034 0.0180 0.0350 0.0830 0.0177 0.1197 0.0551 0.0440 0.0200 0.0807 0.0040 0.0070 0.0236 0.0401 0.0984 0.0236 NOTES MOUNTING PAD 1. Dimensioning and tolerances per ANSI Y14.5M, 1985. 2. Controlling Dimension: Inches 3. Pin 3 is the cathode (Unidirectional Only). 4. Dimensions are exclusive of mold flash and metal burrs. 0.037” (0.95mm) TAPE & REEL ORDERING NOMENCLATURE 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Suffix -T7 = 7 Inch Reel - 3,000 pieces per 8mm tape, i.e., PSOT05LC-T7. 3. Suffix -T13 = 13 Inch Reel - 10,000 pieces per 8mm tape, i.e., PSOT05LC-T13. 0.079” (2.00mm) 0.033” (0.85mm) 0.033” (0.85mm) Outline & Dimensions: Rev 1 - 11/01, 06012 COPYRIGHT © ProTek Devices 2003 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: [email protected] Web Site: www.protekdevices.com DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05066.R4 8/03 5 www.protekdevices.com