AND190HOP Ultra Bright LED Lamps: Type 3 Weight: 1.0g Unit: mm AND190HOP 11.0±0.3 InGaAlP High Brightness Orange Light Emission T-3 Package (10 mm) 10.0±0.2 Features 1.0 MIN. 25.4 MIN. 2.0±0.2 13.5 ± 0.3 • New emission material (InGaAlP) orange LED • Peak wavelength (λp = 620 nm) high bright emission • All plastic mold type, clear colorless lens • Low drive current, (forward current = 1 to 20 mA) • Excellent On-Off contrast ratio • Fast response time, capable of pulse operation • High power luminous intensity • Suitable for Outdoor Message Signboards, Automotive use. • RoHS Compliant 0.5 2.54 Maximum Ratings (Ta = 25°C) 1 2 0.5 Cathode Index 1. Anode 2. Cathode Characteristics Symbol Rating Unit Forward Current IF 50 mA Reverse Voltage VR 5 V PD 125 mW TOpr -40 to 85 °C Power Dissipation Operating Temperature Range Maximum Ratings (Ta = 25°C) Characteristics Storage Temperature Range Symbol Rating Unit TStg -40 to 100 °C Electro-Optical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Minimum Typical Maximum Unit Forward Voltage VF IF = 20 mA – 2.0 2.4 V Reverse Current IR VR = 5 V – – 10 µA Luminous Intensity IV IF = 20 mA 4,000 6,000 – mcd Peak Emission Wavelength λP IF = 20 mA – 620 – nm Spectral Line Half Width ∆λ IF = 20 mA – 18 – nm Dominant Wavelength λd IF = 20 mA – 615 – nm Full Viewing Angle θ IV = 1/2 Peak – 6 – degree Precaution Please be careful of the following: 1. Soldering temperature: 260°C max Product Soldering time: 5 sec. max specifications contained herein may be changed without prior notice. It is therefore advisable to contact Purdy Electronics before proceeding with the design of equipment incorporating this product. Soldering portion of lead: up to 1.6 mm from the body of the device Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 6/12/07 AND190HOP InGaAIP High Brightness Orange Light Emission Ultra Bright LED Lamps: Type 3 IV – IF IF – VF 50000 50 Ta = 25°C Luminous Intensity IV (mcd) Forward Current IF (mA) 30000 Ta = 25°C 30 10 5 3 1 1.6 1.7 1.8 1.9 2.0 2.1 2.2 10000 5000 3000 1000 500 0.5 2.3 1 Forward Voltage VF (V) IV – TC 5 10 30 50 100 Relative Luminous Intensity – Wavelength 3 1.0 Relative Luminous Intensity Relative Luminous Intensity 3 Forward Current IF (mA) 1 0.5 0.3 0.1 -20 0 20 40 60 IF = 20 mA Ta = 25°C 0.8 0.6 0.4 0.2 0 580 80 600 620 640 660 680 700 Wavelength λ (nm) Case Temperature TC (°C) Radiation Pattern IF – Ta 20° 10° 0° 10° Ta = 25°C 20° 30° 30° 40° 40° 50° 50° 60° 60° 70° 70° 80° 80° Allowable Forward Current IF (mA) 80 60 40 20 90° 90° 0 0.2 0.4 0.6 0.8 0 0 20 40 60 80 Ambient Temperature Ta (°C) 100 2. The lead can be formed to 5 mm from the body of the deviceAvenue without• forming stress. Purdyup Electronics Corporation • 720 Palomar Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 6/12/07 AND190HOP InGaAIP High Brightness Orange Light Emission Ultra Bright LED Lamps: Type 3 Soldering should be performed after the lead forming. Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 6/12/07 AND190HOP InGaAIP High Brightness Orange Light Emission Ultra Bright LED Lamps: Type 3 Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 6/12/07