BAT60B Small-Signal Schottky Diodes VOLTAGE RANGE 10 Volts FEATURES * * * * High current rectifier Schottky diode with low VF drop Low voltage, low inductance For power supply For detection and step-up-conversion SOD-323 .071(1.80) .063(1.60) MECHANICAL DATA Case: Molded plastic Epoxy: UL 94V-O rate flame retardant Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.004 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 OC ambient temperature unless otherwise specified. .006(.15) .014(.35) .010(.25) .055(1.40) .047(1.20) .106(2.70) .098(2.50) .003(.08) * * * * * MAX.039(1.00) Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. REF .019(0.46) .004(.10) .000(.00) Dimensions in inches and (millimeters) MAXIMUM RATINGS (@T A =25 OC unless otherwise noted) SYMBOL BAT60B Non-Repetitive Peak Reverse Voltage RATINGS VRM 10 UNITS Volts Maximum Forward Comtinuous Current IFM 3 Amps Forward Surge Current @ t=10ms Amps IFSM 5 Junction Capacitance (Note 1) CT 30 pF Maximum Power Dissipation (Note 2) Ptot 250 mW Junction Temperature TJ 150 O TSTG -65 to + 150 O Storage Temperature Range C C ELECTRICAL CHARACTERISTICS (@T A =25 OC unless otherwise noted) CHARACTERISTICS SYMBOL BAT60B UNITS Maximum Instantaneous Forward Voltage @IF=10mA @IF=100mA @IF=500mA @IF=1000mA VF 300 380 500 600 mVolts Maximum Instantaneous Peverse Current @VR=5V @VR=8V IR 15 25 uAmps NOTES : 1. Measured at 1MHz and applied reverse voltage of 5 volts. 2. Part mounted on FR-4 PC board with minimunm recommended pad layout. 2008-12 REV: A RATING AND CHARACTERISTICS CURVES ( BAT60B ) A 3200 125 OC 10-3 mA 85 OC 10-4 2400 25 OC 2000 10-6 IR IR 10-5 10-7 1600 1200 -40 OC 10-8 800 10-9 400 10-10 0 0 2 4 6 8 V 12 0 20 40 60 80 100 120 OC 150 S 100 FORWARD CURRENT IF = f (TS) REVERSE CURRENT IR = f (VR) Figure 1 Figure 2 100 102 A 10-2 IFmax/IFDC 10-1 -40 OC IF 25 OC 85 C O 10-3 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 101 125 OC 10-4 10-5 0 0.1 0.2 0.3 0.4 0.5 0.6 V 0.8 100 10-6 10-5 10-4 10-3 10-5 FORWARD CURRENT IF = f (VF) PERMISSIBLE PULSE LOAD IFmax/IFDC = f (tp) Figure 3 Figure 4 RATING AND CHARACTERISTICS CURVES ( BAT60B ) 102 101 RthJS 0.5 0.2 0.1 0.05 0.02 0.01 0.005 D=0 100 10-1 10-6 10-5 10-4 10-3 10-5 S PERMISSIBLE PULS LOAD RthJS = f (tp) Figure 5 100 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures. RECTRON