RECTRON SF166 SEMICONDUCTOR TECHNICAL SPECIFICATION GLASS PASSIVATED SUPER FAST RECTIFIER VOLTAGE 400 Volts CURRENT 16.0 Amperes FEATURES * * * * * * * Low switching noise Low forward voltage drop Low thermal resistance High current capability Super fast switching speed High reliability Good for switching mode circuit TO-220A MECHANICAL DATA * * * * * .108 (2.75) Case: TO-220A molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 2.24 grams .413 (10.5) .374 (9.5) .153 (3.9) .146 (3.7) .187 (4.7) .148 (3.8) .270 (6.9) .230 (5.8) .053 (1.3) .047 (1.2) .610 (15.5) .583 (14.8) .04MAX. (1.0) .157 (4.0) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. .583 (14.8) .531 (13.5) .051 (1.3) .035 (0.9) .028 (0.7) .022 (0.56) .014 (0.36) .126 (3.2) .102 (2.6) .091 (2.3) For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) SYMBOL SF166 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 400 Volts Maximum RMS Voltage V RMS 280 Volts VDC 400 Volts IO 16.0 Amps Amps RATINGS Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TC = 100oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range I FSM 250 RθJC 1.2 RθJA CJ 16 175 T J , T STG -55 to + 150 SYMBOL SF166 UNITS VF 1.35 Volts 0 C/ W pF 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 16.0A DC @T C = 25 o C Maximum DC Reverse Current at Rated DC Blocking Voltage @T C = 100 oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. Suffix “R” for Reverse Polarity. IR trr 10 500 50 uAmps nSec 2002-11 1000 16 12 8 Single Phase Half Wave 60Hz Inductive or Resistive Load 4 0 PEAK FORWARD SURGE CURRENT, (A) 50 100 CASE TEMPERATURE, ( ) 150 FIG. 3 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 300 INSTANTANEOUS REVERSE CURRENT, (uA) 20 0 TJ = 100 100 10 TJ = 25 1.0 250 0.1 200 0 8.3ms Single Half Sine-Wave (JEDEC Method) 150 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 100 50 0 1 INSTANTANEOUS FORWARD CURRENT, (A) FIG. 2 - TYPICAL REVERSE CHARACTERISTICS FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 50 30 20 14 12 10 4 2 1.0 .6 TJ=25 Pulse Width = 300uS 1% Duty Cycle .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) AVERAGE FORWARD CURRENT, (A) RATING AND CHARACTERISTIC CURVES ( SF166 ) 2.0 10000 1000 100 10 .1 TJ = 25 .2 .4 1.0 2 4 10 20 40 REVERSE VOLTAGE, ( V ) RECTRON 100