SSO-AD-230-TO52i Avalanche Photodiode Special characteristics: High gain at low bias voltage Fast rise time 230 µm diameter active area low capacitance Package 1a (TO52i) : Parameters: 2 Active area 1) dark current (M=100) 1) Total capacitance (M=100) Break-down voltage UBR (bei ID=2µA) Temperature coefficient of UBR Spectral responsivity at 780 nm Cut-off frequency (-3dB) Rise time 0,042 mm ∅ 230 µm max. 1,5 nA typ. 0,6 nA typ. 1,5 pF (90 ... 240) typ. 120 - 190 V typ. 0,4 %/°C min. 0,40 A/W typ. 0,45 A/W typ. 2 GHz typ. 180 ps Optimum gain Gain M "Excess Noise" factor (M=100) "Excess Noise" index (M=100) Noise current (M=100) N.E.P. (M=100, 880 nm) Operating temperature Storage temperature 50 - 60 min 200 typ. 2,2 typ. 0,2 ½ typ. 0,5 pA/Hz -14 ½ typ. 1 * 10 W/Hz -20 ... +70°C -60 ... +100°C 1) measurement conditions: Setup of photo current 10nA at M=1 and irradiation by a NIR-LED (880 nm, 80 nm bandwith). Rise of the photo current up to 1 µA, (M=100) by internal multiplication due to an increasing bias voltage SSO - AD - serie Spectral Responsivity at M=100 0,600 60 0,500 50 0,400 40 Sabs (A/W) Sabs (A/W) SSO - AD - serie Spectral Responsivity at M=1 0,300 30 0,200 20 0,100 10 0,000 0 400 500 600 700 800 900 1000 1100 400 500 600 Wavelength (nm) 700 800 900 1000 1100 Wavelength (nm) SSO - AD - serie quantum efficiency for M=1 SSO-AD 230 Ctot=f(UR) at f=100kHz 1,00 16 0,90 14 0,70 12 0,60 10 Ctot (pF) QE 0,80 0,50 0,40 8 6 0,30 4 0,20 2 0,10 0,00 0 400 480 560 640 720 800 880 960 1040 0 20 40 SSO-AD 230 dark current = f(UR) 80 100 SSO-AD 230 gain = f(UR/UBR) at λ = 880 nm 1000 10000,00 100 ID (pA) 60 UR (V) wavelength (nm) 1000,00 10 M 100,00 1 10,00 0,1 0,01 1,00 0 20 40 60 80 100 120 140 160 0,0 0,2 0,4 UR (V) 0,6 0,8 1,0 UR/UBR Maximum Ratings: • • • max. electrical power dissipation max. optical peak value, once max. continous optical operation • ( Pelectr. = Popt. * Sabs * M * UR ) 100 mW at 22°C 200 mW for 1 s IPh (DC) ≤ 250 µA ≤ 1 mA for signal 50 µs "on" / 1 ms "out" Bias supply voltage Current limiting resistor Application hints: • • • • • • • Current limit is to be realized via protecting resistor or current limiting - IC inside the supply voltage. Use of low noise read-out - IC. For higher gain a regulation of bias voltage due to the temperature is to be realized. For very small signals stray light (noise source) is to be excluded by filters in order to improve the signal-noise relation. Avoid touching the window with fingers! Careful cleaning with Ethyl alcohol possible. Avoid use of pointed and scratching tools! min. 0,1 µF, closest to APD APD Diode, protective circuit Read-out circuit or f.e. 50Ω Load resistance Handling precautions: • • • • Soldering temperature min. Pin - length ESD - protection Storage 260°C for max. 10 s. The device must be protected against solder flux vapour! 2mm Only small danger for the device. Standard precautionary measures are sufficient. Store devices in conductive foam. 1999/07