Analog 4-wire PET-On-Glass Touch Screen Specification 1. Mechanical Dimensions and Construction 1.1 1.2 General: Analog Resistive touch screen is laminated by ITO PET to ITO glass. Construction : Item 1 2 3 4 5 6 7 8 9 10 11 12 13 Description ITO PET (Top layer) Material 0.188mm ITO PET Film ITO Patterned Glass (Bottom layer) 1.10mm ITO Glass Tail Base Tail Coverlay Conductor Top layer circuit Bottom layer circuit Layer to layer contacted Dot spacer Isolation Layer Stiffener Glue Tape Kapton Kapton Copper Silver ink Silver ink Silver ink UV Cure ink Isolation Adhesive Polyester UV Glue PET Film Remarks Antiglare coating Surface hardness: 3H Resistance:300~600Ω/□ Resistance:300~600Ω/□ Separated Tail Touch screen side view: Changes that contribute to technical improvement are subject to alternations 2006 Bearb. Gepr. Vert. Datum 21.08. 21.08. Name Maurer Maurer TOUCH SCREEN 5,72“, 4 Wire EDV-Datasheet AMT-09532-5-A1 SPECIFICATIONS OF ANALOG RESISTIVE PET-ON-GLASS TOUCH SCREEN don’t change manually Manufactured by Apex Material Technology Corp. H Zu Änd. Datum Name D 79346 Endingen 1070,0456 page 1 of 4 Index: - 1.3 Input Method and Activation Force Input Method 1.6mm Ø Delrin stylus 16mm Ø Silicon "finger" Average Activation Force 0,10 ~ 0,70 N 0,10 ~ 0,70 N 2. Typical Optical Characteristics 2.1 Visible Light Transmission: 2.2 Haze: > 80% < 13% 3. Electrical Specifications 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Operating Voltage: Contact current: Circuit close resistance: Circuit open resistance: Contact bounce: Linear Test : Capacitance: 5.5V or less 20mA (maximum) X : 350~900Ω Y : 200~700Ω > 10MΩ at 25VDC < 10ms <1.5 % 100nF(maximum) 4. Linearity 4.1 Linear Test Specification Direction X: <1.5 % Direction Y: <1.5 % 5. Environment Specification 5.1 Operating Temperature - 10° C ~ + 60° C 5.2 Storage Temperature - 20° C ~ + 80° C Humidity less than 90% RH at Ambient Humidity Changes that contribute to technical improvement are subject to alternations 2006 Bearb. Gepr. Vert. Datum 21.08. 21.08. Name Maurer Maurer TOUCH SCREEN 5,72“, 4 Wire EDV-Datasheet AMT-09532-5-A1 SPECIFICATIONS OF ANALOG RESISTIVE PET-ON-GLASS TOUCH SCREEN don’t change manually Manufactured by Apex Material Technology Corp. H Zu Änd. Datum Name D 79346 Endingen 1070,0456 page 2 of 4 Index: - 6. Reliability Test 6.1 Exposure to high temperature Touch panel is put into a test machine at the condition of 80°C for 288 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 6.2 Exposure to low temperature Touch panel is put into a test machine at the condition of –40°C for 288 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 6.3 Exposure to constant temperature and humidity Touch panel is put into a test machine at the condition of 60°C, 90%RH for 288 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 6.4 Thermal Shock Touch panel is put into a test machine at the condition of –40°C for 30 minutes, and then 80°C for 30 minutes. The process is repeated by 10 cycles. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 Changes that contribute to technical improvement are subject to alternations 2006 Bearb. Gepr. Vert. Datum 21.08. 21.08. Name Maurer Maurer TOUCH SCREEN 5,72“, 4 Wire EDV-Datasheet AMT-09532-5-A1 SPECIFICATIONS OF ANALOG RESISTIVE PET-ON-GLASS TOUCH SCREEN don’t change manually Manufactured by Apex Material Technology Corp. H Zu Änd. Datum Name D 79346 Endingen 1070,0456 page 3 of 4 Index: - 7. Durability test: 7.1 Finger touches Touch panel is hit 10 millions times with a silicone rubber of R8 finger, hitting rate is by 250g at 2 times per second. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 7.2 Stylus writing Touch panel is drawn by R 0,8 Derlin stylus pen, at 250g forces, repeat one inch by 100K times. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 8. Optical Performance 8.1 Optical inspection method and optical defect standards refer to document. A001-1 Touch Screen Optical Quality Standard. 8.2 Outside to Viewing Area : any optical defected in this area need to be ignored if no effected to touch screen function. 8.3 Silver Bus Pattern defect : Voids in traces to be less than 50% of the trace width. 8.3.1 Silver Bus Pattern gap: >0.1mm 8.3.2 Silver Bus and Active area gap: No silver ink may project beyond the viewing area. 8.4 Glass defects such as edge chips and scratches refer to A001-1 Touch Screen Optical Quality Standard. 8.5 Others 8.5.1 Folding line should be avoided on the pressure sensitive adhesive. 8.5.2 Refer to document A001-1 Touch Screen Optical Quality Standard. 8.5.3 Always store the touch screen in its original shipping container under normal conditions (20~25°C, 65% RH) Changes that contribute to technical improvement are subject to alternations 2006 Bearb. Gepr. Vert. Datum 21.08. 21.08. Name Maurer Maurer TOUCH SCREEN 5,72“, 4 Wire EDV-Datasheet AMT-09532-5-A1 SPECIFICATIONS OF ANALOG RESISTIVE PET-ON-GLASS TOUCH SCREEN don’t change manually Manufactured by Apex Material Technology Corp. H Zu Änd. Datum Name D 79346 Endingen 1070,0456 page 4 of 4 Index: -