SCHURTER 1070.0476

Analog 5-wire PET-On-Glass Touch Screen Specification
1. Mechanical Dimensions and Construction
1.1 General: Analog Resistive touch screen is laminated by ITO PET to ITO glass.
1.2 Construction:
Item
1
2
3
4
5
6
7
8
9
10
11
12
Description
ITO PET
(Top layer)
New designed printing
ITO Patterned Glass (Bottom layer)
New designed printing
Tail Base
Tail cover lay
Connector
Top layer circuit
Bottom layer circuit
Layer to layer contacted
Dot spacer
Isolation Layer
Glue
Preserve pet
Material
Remarks
0.188mm ITO PET Antiglare coating
Film
Surface hardness: 3H
Resistance:300~600Ω/□
2.8 mm ITO Glass Resistance:300~900Ω/□
Kapton
Separated Tail
Kapton
AMP compatible
2,54mm
Silver ink
Silver ink
Silver ink
UV Cure ink
Isolation Adhesive
UV Glue
PET Film
Touch screen side view:
Changes that contribute to technical improvement are subject to alternations
2006
Bearb.
Gepr.
Vert.
Datum
18.08.
18.08
Name
Maurer
Maurer
TOUCHSCREEN
17,15", 5-Wire
EDV-Datasheet
AMT-02512-01
SPECIFICATIONS OF ANALOG RESISTIVE
PET-ON-GLASS TOUCH SCREEN
don’t change manually
Manufactured by Apex Material Technology Corp.
H
Zu Änd.
Datum
Name
D 79346 Endingen
1070.0476
page 1 of 4
Index: -
1.3 Input Method and Activation Force
Input Method
16mm dia. Silicon "finger"
Average Activation Force
Less than 1.00 N
2. Typical Optical Characteristics
2.1
2.2
Visible Light Transmission:
Haze:
> 80%
< 13%
3. Electrical Specifications
3.1
3.2
3.3
3.4
3.5
3.6
Operating Voltage:
Contact current:
Circuit close resistance:
Circuit open resistance:
Contact bounce:
Linearity Specifications:
5.5V or less
20mA (maximum)
20~300Ω
> 10MΩ at 25VDC
< 15ms
The linearity specifications are based on Hampshire or
PenMount touch screen controllers and drivers to define.
10 mm inside of X and Y active area dimensions.
The area 10 mm inside of X and Y active area dimensions.
3.6.1 Inner Active Area :
Perimeter of Active Area :
Changes that contribute to technical improvement are subject to alternations
2006
Bearb.
Gepr.
Vert.
Datum
18.08.
18.08
Name
Maurer
Maurer
TOUCHSCREEN
17,15", 5-Wire
EDV-Datasheet
AMT-02512-01
SPECIFICATIONS OF ANALOG RESISTIVE
PET-ON-GLASS TOUCH SCREEN
don’t change manually
Manufactured by Apex Material Technology Corp.
H
Zu Änd.
Datum
Name
D 79346 Endingen
1070.0476
page 2 of 4
Index: -
3.6.2 Calculate Linearity
% Linearity =
∆X 2 + ∆Y 2
* 100
Active Area Diagonal
£ G
Y
£ G
X
3.6.3 Linearity:
Inner Active Area :
Perimeter of Active Area :
<1.0%
<1,5%
3.7 Electrostatic Discharge Protection : (per EN 61000-4-2 ) The touch screen withstands of 15KV air discharge
and 8KV contact discharge.
4. Environment Specification
4.1
4.2
Operating Temperature
Storage Temperature
- 10° C ~ + 60° C Humidity less than 90% RH, no dew condensation
- 40° C ~ + 80° C, at Ambient Humidity
5. Reliability Test
5.1
Exposure to high temperature
Touch panel is put into a test machine at the condition of 80°C for 504 hours.
Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following:
- Circuit close resistance: as Sec. 3.3
- Circuit open resistance: as Sec. 3.4
- Contact bounce: as Sec. 3.5
- Linearity test: as Sec. 3.6
5.2
Exposure to low temperature
Touch panel is put into a test machine at the condition of –40°C for 504 hours.
Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following:
- Circuit close resistance: as Sec. 3.3
- Circuit open resistance: as Sec. 3.4
- Contact bounce: as Sec. 3.5
- Linearity test: as Sec. 3.6
Changes that contribute to technical improvement are subject to alternations
2006
Bearb.
Gepr.
Vert.
Datum
18.08.
18.08
Name
Maurer
Maurer
TOUCHSCREEN
17,15", 5-Wire
EDV-Datasheet
AMT-02512-01
SPECIFICATIONS OF ANALOG RESISTIVE
PET-ON-GLASS TOUCH SCREEN
don’t change manually
Manufactured by Apex Material Technology Corp.
H
Zu Änd.
Datum
Name
D 79346 Endingen
1070.0476
page 3 of 4
Index: -
5.3
Exposure to constant temperature and humidity
Touch panel is put into a test machine at the condition of 60°C, 90%RH for 504 hours. Then it is left at the room
temperature for 24 hours or more. The measurement must satisfy the following:
- Circuit close resistance: as Sec. 3.3
- Circuit open resistance: as Sec. 3.4
- Contact bounce: as Sec. 3.5
- Linearity test: as Sec. 3.6
5.4
Thermal Shock
Touch panel is put into a test machine at the condition of –40°C for 30 minutes, and then 80°C for 30 minutes.
The process is repeated by 10 cycles. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following:
- Circuit close resistance: as Sec. 3.3
- Circuit open resistance: as Sec. 3.4
- Contact bounce: as Sec. 3.5
- Linearity test: as Sec. 3.6
6. Durability test:
6.1
Finger touches
Touch panel is hit 36 millions times with a silicone rubber of R8 finger, hitting rate is by 250g at 2 times per
second. The measurement must satisfy the following:
- Circuit close resistance: as Sec. 3.3
- Circuit open resistance: as Sec. 3.4
- Contact bounce: as Sec. 3.5
- Linearity test: as Sec. 3.6
7. Optical Performance:
7.1
Optical inspection method and optical defect standards refer to document. A001-2 Touch Screen Optical Quality
Standard.
7.2
Outside to Active Area : any optical defected in this area need to be ignored if no effected to touch screen function.
8. Others
8.1
Always store the touch screen in its original shipping container under normal conditions (20~25°C, 65% RH)
Changes that contribute to technical improvement are subject to alternations
2006
Bearb.
Gepr.
Vert.
Datum
18.08.
18.08
Name
Maurer
Maurer
TOUCHSCREEN
17,15", 5-Wire
EDV-Datasheet
AMT-02512-01
SPECIFICATIONS OF ANALOG RESISTIVE
PET-ON-GLASS TOUCH SCREEN
don’t change manually
Manufactured by Apex Material Technology Corp.
H
Zu Änd.
Datum
Name
D 79346 Endingen
1070.0476
page 4 of 4
Index: -