Technical Data Sheet Pb Free Specification SSC-FCW100 (Rev 1.7, General) SSC Drawn Approval Customer Approval SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) Technical Data Sheet [ Contents ] 1. Absolute maximum ratings 2. Electro-optical characteristics 3. CIE Chromaticity Diagram 4. Characteristic diagram 5. Soldering profile 6. Outline dimension 7. Recommended soldering pad design 8. Reel packing dimension 9. Packing 10. Precaution for use SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) Technical Data Sheet SSC-FCW100 Description • White colored SMT package • Suitable for all SMT assembly methods and all soldering methods SSC-FCW100 Features • 2.0 X 1.5 X 0.5 mm • x, y coordination x: 0.31, Y 0.31 Applications • Cellular phone’s Flash lighting • Other decoration lighting SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) Technical Data Sheet 1. Absolute maximum ratings *1 (Ta=25℃) Parameter Symbol Value Unit Power Dissipation Pd 560 mW Forward Current IF 175 mA Peak Forward Current IFM *2 600 mA Reverse Voltage VR 5 V LED Junction Temperature Tj 125 ℃ Operation Temperature Topr. -30 ~ 85 ℃ Storage Temperature Tstg. -40 ~ 100 ℃ *1 Care is to be taken that power dissipation does not exceed the absolute maximum rating of the product. *2 IFM conditions is pulse width Tw ≤ 300ms and Duty ratio≤1/10 2. Electro-Optical Characteristics Parameter Symbol Forward Voltage VF (Ta=25℃) Condition Min Typ Max IF=175 ㎃ 2.7 3.0 3.7 3.2 - V IF=320 ㎃ (Flash mode*2) Reverse Current Luminous Intensity*1 IR IV VR=5V - - 30 IF=175 ㎃ 2.5 5.5 8 IF=320 ㎃ - 9 - IF=175 ㎃ - 17 25 IF=175 ㎃ - 5.5 8 IF=320 ㎃ - 9 - - 0.31 - - 0.31 - (Flash Luminous Flux*3 Illumination*4 ΦV lx mode*2) (Flash mode*2) X Chromaticity Coordination Y Viewing Angle*5 2θ1/2 IF=175 ㎃ IF=20 ㎃ Unit ㎂ cd Lm lx@1m ˚ 130 *1. The luminous intensity IV is measured at the peak of the spatial pattern which may not be aligned with the mechanical axis of the LED package. *2. Flash mode conditions are pulse width Tw = 1sec, duty ratio = 2/7 *3. Luminous flux measurement allowance is ±10% *4. This luminous intensity (Lux) is measured at a distance of 1m with condition Ta = 25℃ and it has 10% tolerance. *5. θ1/2 is the off-axis where the luminous intensity is ½ of the peak intensity. [Note] All measurements were made under the standardized environment of SSC (Tolerance : Color Coordinate ± 0.005, VF = ± 0.1) SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) 0.9 0.34 0.32 y Coord. 0.8 0.7 y Coord. Technical Data Sheet 3. CIE chromaticity Diagram C 0.30 0.28 0.6 0.26 0.5 0.24 0.24 B 0.26 0.28 0.30 0.32 0.34 x Coord. 0.4 0.3 0.2 0.1 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 x Coord. ※ Color Rank Rank Chromaticity Coordination x 0.247 0.292 0.272 0.317 y 0.255 0.255 0.300 0.300 x 0.272 0.317 0.295 0.335 y 0.300 0.300 0.335 0.335 B C SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) Technical Data Sheet 4. Characteristic Diagram Relative Intensity vs Forward Current Forward Current vs Forward Voltage 1000 Ratio of Luminous Intensity [%.] Forward Current [mA] 250 100 10 200 150 100 50 0 0 100 200 1 300 400 500 600 Forward Current [mA] 2.6 2.8 3.0 3.2 3.4 3.6 Forward Voltage [V] Forward Current vs Derating Curve Forward Current vs Chromaticity Coordinate 200 0.33 x y Chromatisity Coordinate x, y [a.u.] 180 Forward current IF(mA) 160 140 120 100 80 60 40 0.32 0.31 0.30 20 0 -2 5 0 25 50 75 o A m b ie n t te m p e ra tu re T a ( C ) 100 0.29 50 100 150 200 250 300 350 Forward Current [mA] SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 110 100 90 (Ta=25℃, IF=175mA) 80 70 120 60 130 50 140 40 30 150 160 20 170 10 180 0 Y Y Spectrum o Ta = 25 C 1.0 0.8 Intensity [a.u.] Technical Data Sheet Radiation Diagram 0.6 0.4 0.2 0.0 400 450 500 550 600 650 700 750 W avelength [nm ] SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) Reflow Soldering Conditions/ Profile (1) Lead Solder • Preliminary heating to be at 210℃ max. for 2 minutes max. • Soldering heat to be at 240℃max. for 10 seconds max. o Device Surface Temperature [ C] 280 240 200 160 120 80 40 0 0 15 30 45 60 75 90 105 120 135 150 165 180 195 Soldering Times [sec] (2) Lead-Free Solder • Preliminary heating to be at 220℃max. for 2 minutes max. • Soldering heat to be at 260℃max. for 10 seconds max. 280 o Device Surface Temperature [ C] Technical Data Sheet 5. Soldering profile 240 200 160 120 80 40 0 0 15 30 45 60 75 90 105 120 135 150 165 180 195 Soldering Times [sec] (3) Hand Soldering Condition • Not more than 3 seconds @MAX280℃, under Soldering iron. [Note] In case the soldered products are reused in soldering process, we don’t guarantee the products. SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) Tolerance: ±0.05, Unit: ㎜ 0.18 Resin Anode [SIDE VIEW] 0.50 1.20 2.00 0.50 ±0.05 1.50 [TOP VIEW] ±0.03 PCB 1.60 2.00 Technical Data Sheet 6. Outline Dimension 1.50 [BOTTOM VIEW] Cathode [Circuit Diagram] 7. Recommended Soldering pad design [ Normal Solder pad ] [ Solder pad for heat radiation ] SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) 1.75±0.1 8.0±0.2 4.0±0.1 0.65±0.1 ? 1.5 +0.1 -0 (2.75) 3.5±0.05 0.2±0.05 180 11.4 +0 -3 9 ±0.2 +0.2 -0 2 ±0.3 60 Technical Data Sheet 8. Reel Packing Dimension 22 13 ±0.2 Label Tolerance: ±0.2, Unit: ㎜ (1) Quantity: 2,000pcs./Reel (2) Cumulative Tolerance: Cumulative Tolerance/10pitches to be ±0.2mm (3) Adhesion Strength of Cover Tape: Adhesion strength to be 0.1-0.7N when the over tape is turned off from the carrier tape at10˚angle to be the carrier tape. (4) Package: P/N, Manufacturing data Code No. and quantity to be indicated on a damp proof Package. SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) Reel # # # # # # # # # # : N / P ## 제 품 명 : SSC-FCW 100 # # # # # # # # # # o N t o L Technical Data Sheet 9. Packing 수 량 : 2,000 Aluminum Vinyl Bag # # # # # # # # # # : N / P ## 제 품 명 : SSC-FCW 100 # # # # # # # # # # o N t o L 수 량 : 2,000 Outer Box *Material: Paper(SW3B(B)) SIZE(mm) TYPE a 245 7inch b 220 c 142 c CHIP LED PART : SSC-FCW 100 CO DE : Q 'YT : 20,000EA CHIP LED b a LO T N O : DATE : S EO UL S EM IC ON DU CTOR C O.,LTD SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0) Technical Data Sheet 10. Precaution for Use (1) Storage In order to avoid the absorption of moisture, it is recommended to store in the dry box (or desiccator) with a desiccant. Otherwise, to store them in the following environment is recommended. Temperature : 5℃~30℃ Humidity : 60%HR max. (2) Attention after opened However LED is corresponded SMD, when LED be soldered dip, interfacial separation may affect the light transmission efficiency, causing the light intensity to drop. Attention in followed. a. After opened and mounted, the soldering shall be quickly. b. Keeping of a fraction Temperature : 5 ~ 40℃ Humidity : less than 30% (3) In case of more than 1 week passed after opening or change color of indicator on desiccant components shall be dried 10-12hr. at 60±5℃. (4) In case of supposed the components is humid, shall be dried dip-solder just before. 100Hr at 80±5℃ or 12Hr at 100±5℃. (5) Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temp. after soldering. (6) Quick cooling shall not be avoid. (7) Components shall not be mounted on warped direction of PCB. (8) Anti radioactive ray design is not considered for the products listed here in. (9) Gallium arsenide is used in some of the products listed in this publication. These products are dangerous if they are burned or smashed in the process of disposal. It is also dangerous to drink the liquid or inhale the gas generated by such products when chemically disposed. (10) This device should not be used in any type of fluid such as water, oil, organic solvent and etc. When washing is required, IPA should be used. (11) When the LEDs are illuminating, operating current should be decided after considering the ambient maximum temperature. (12) LEDs must be stored to maintain a clean atmosphere. If the LEDs are stored for 3 months or more after being shipped from SSC, a sealed container with a nitrogen atmosphere should be used for storage. (13) The LEDs must be soldered within seven days after opening the moisture-proof packing. (14) Repack unused products with anti-moisture packing, fold to close any opening and then store in a dry place. (15) The appearance and specifications of the product may be modified for improvement without notice. SSCSSC-FCW100 Revision 1.7 www.ZLED.com 서식번호 : SSC-QP-7-07-24 (Rev.0.0)